Develop Bugs

P3300 Boot Problem

Please Help
I Have A P3300 And After Changing Rom (had Greek Rom) And I Put The Pdaviet The Pda Can Not Boot.
I Tried With Hard Reset To Make It Boot Again But Even If I Tried Several Times The Result Is Always The Same:
Ipl 3.04.0001
Spl 3.04.000.
Gsm 02.93.90
Os 4.0.0.0
And The Booting Stops There
Does Anybody Can Help?

LINANTONIS said:
Please Help
I Have A P3300 And After Changing Rom (had Greek Rom) And I Put The Pdaviet The Pda Can Not Boot.
I Tried With Hard Reset To Make It Boot Again But Even If I Tried Several Times The Result Is Always The Same:
Ipl 3.04.0001
Spl 3.04.000.
Gsm 02.93.90
Os 4.0.0.0
And The Booting Stops There
Does Anybody Can Help?
Click to expand...
Click to collapse
can you enter the boatloader?

Boot Problem
Unfortunately I Can Not Syncronize It So I Can Not Put The Boatloader

you can go into the bootloader by pressing the voice speed dial button and soft reset your device.
then you will get a 3 collor screen (red,green and blue). if you are in the screen connect your usb cable and you will have a connection so you can update the rom.
first use USPL and after that run the rom update utility

Thank You For Your Help
But I Did What You Told Me I Connected And I Start Running The Uspl.
Unfortunately The Spl Can Not Finish And Stuck Always In 50.
From 30 To 50 The Message Is :cant Spawn Cmd.exe.:no Such File In Directory C:

Help Error CODE 244

new guy, not getting alot from the threads on error 244 during flash.
The raw info to catch my helpers up to speed:
1) My device = MDA Compact III - german version
IPL= 1.13.0001
SPL=1.11.0000
GSM=02.49.90
OS=1.13.0.0
2) I Flashed the USPL. I got to white screen and lost Activesync. I stayed in White Screen, went into boot loader mode and reconnected usb to device and saw USB in corner of screen and re-ran USPL-ROM UPDATE UTILITY and wasnt sure if I got the USPL rom on my device.
3) I assume I did because my SPL is 1.11.0000 after it rebooted.
4) I then tried to run the WWE-ROM UPDATE UTILITY for art_tmouk_11311001_024990...TMO_UK so I could change the language from German to English.
5) I got error code 244-device wouldnt support it at roughly the 3% mark of flashing process.
***********I need english*******I need expert help********I need detailed instructions******=Baby steps******** Somebody, anybody somewhere somehow-help me get english rom on my device!!!!!!!!!!!!!!!!!!!
Until the gadget gods shed there light on me, I am stuck with phone I cant understand. Actually all I want is enough knowledge to be dangerous messing with expensive electronic devices. I can break anything with electron flow!!!!!!!!!!!!!!!!!

my ARTEMIS is blocked "BRICK" please help

I updated my rom from the original spanish version to a Artemis_Touch_3.01
After some use, the device is blocked.
It starts the HArd reset, after "Format messages" It starts HTC white screen
IPL 3.13.0001
SPL 3.13.0000
and nothing more
.
It also works ROM update mode (Three colors screen) but when I execute the Rom update frommy pc, it reaches 2/3% and gives different Errors depending the ROM,
"Ivalid Vender ID [294] when I use the ROM HTC_P3300_SPA_3.13.412.1_4.1.13.44_02.94.90_Ship_R
ERROR [270]: Update Error -The Image File is corrupted - When I use Black & Blue 4.3 or Artemis_Touch_3.01
I need help!!!

brick?
hello,
First you must open the bootloader menu,
hold voice dial button and press soft reset.
If this not working hold voice dial and on/off button and softreset.
You must connect first your htc with your pc and the start the bootloader.
When you are in the bootloader menu, you can upload an orginal fabricrom to your htc.
Search xda-developer for the fabric rom.
And then you can change your rom for something else but don't forget the uspl.
When you want to change image you must install the uspl first otherwise everthing will blocked

the problem you have is that you have to run the uspl first before you can flash another firmware. If you run the uspl you will see that the spl loader of your device is version 1.11.000 and than you can flash an other rom of your choice
greetzz Patrick

uspl does not work. this is the point you can not get it.

have a problem but I cannot find anything useful for my case, maybe you can help me?
pvdhelm said:
the problem you have is that you have to run the uspl first before you can flash another firmware. If you run the uspl you will see that the spl loader of your device is version 1.11.000 and than you can flash an other rom of your choice
greetzz Patrick
Click to expand...
Click to collapse
Hi Patrick,
I have a dutch rom on my htc P3300
IPL: 1.12.0001
SPL: 1.12.0000
GSM: 02.67.90
os: 1.12.0.0
my HTC remains stuck on the startup screen (logo HTC) and will not get any further.
Connection with active synch is not possible, ans holding the buttons reset-voice rec-on/off buttons don't react. WM cannot be started in that way.
is it possible to find a boot program which allows me to start up WM again like a regular PC? something like a emergency startup disk? I have a 2GB micro SD card. After reading and trying so many things, I lost the way in this site and was hoping maybe you can send me some useful links that can solve my problem? I would appriciate the effort.I don't know if it's allowed to send my personal emailadress? If it is allowed please let me know. Maybe we can exchange directly some info, otherwise I don't have a problem mailing this site.
(I hope I can find this thread again after closing?)
Kind regards , Eli

my artemis is also in the same state
Hi All,
Please help me with problem which I am facing with my HTC P3300
When i switch it on..Its stuck in the state where it shows
IPL 3.07.0001
SPL 1.11.0000
GSM 03.08.90
OS 3.4.0.0
What I tried.
1. I tried USPL , its not loading as device is not getting detected in my laptop.
2. Volume Down+Reset is not working
Please help me with this

Confused about possible bricked device

My Device
T Mobile compact 111 (HTC P3300)
IPL 1.13.0001
SPL 1.13.0000
GSM 02.49.90
OS 3.4.0.0
I have spent hours and hours reading the form and following instructions on how to fix my device but without success.
First the device was stuck on the startup T-mobile Logo screen
Then after using mtty.exe and following instructions The device was then stuck on the boot loader screen. I have tried RUUWrapper and Hard-SPL-V7 but no joy – couldn’t get any connection to my device
I then tried Hard-SPL-v9 which did actually connect to my device
This changed the problem from ‘stuck on the boot loader’ back top ‘stuck on startup screen (t-mobile logo)’ but produced the following error
(ERROR [270]: UPdate Error
The image is corrupted. Please check your Update Utility)
I tried SSPL-HERM on the sd card but nothing!
I searched for “Hard SPL 1.1.3 utility” and didn’t find any utility for this
I have tried the suggested removing the battery soft reset hard reset etc etc
I’ve nearly pulled all my hair out!!! Arrrrrrrrrrrrrr!
Where can I go from here please?
Are there any specific downloads etc?
Many Many thanks

LAST HOPE!

I'm having a mare....my Artemis has died after a hard reset - just sits at bootloader. I can't flash any rom at all using RUU. All cooked roms fail after 3% with a "image corrupt" error and all original roms (wm5 and wm6 for o2 orbit) fail after 5% with "Flash Write" error.
I've also tried flashing from SD card....starts...but then fails on the validating certificate with an "SD FAT error" or sorts.
I know it's probably salvagable as I can get into bootloader....any ideas? People on forums are telling me to unlock using USPL...but because i cant get into the os to get activesync....it won't work.

a simular thing happens to me my one sits in a rgb screen and says ipl 3.04.0001 and spl 3.04.0000. none of the roms i used work ive just decided to leave it. if your ipl and spl is lower than mine i guess you will be more likley to get working again as people with the same ipl and spl as me cant get their one working

Try to go to bootloader and try to use it :
http://forum.xda-developers.com/showthread.php?t=311403
If it work try to flash with any custums roms.
If you don't have this , you only can flash with officials roms. That's why you can't flash with custums roms

Qui-Gon Ginn said:
Try to go to bootloader and try to use it :
http://forum.xda-developers.com/showthread.php?t=311403
If it work try to flash with any custums roms.
If you don't have this , you only can flash with officials roms. That's why you can't flash with custums roms
Click to expand...
Click to collapse
Thanks for this however I;ve been directed to that thread before and each time it's pointless. There is no point me attempting to USPL my device when I can't get an activesync connection due to the fact it has no OS bootable.
As for the official Roms...I've tried the ones that have been touted as official for the Orbit but with no effect.
My IPL SPL is currently 1.25.0001/1.25.0.000 but when i attempt to flash with official rom (!) it moves to the same as spikez - ipl 3.04.0001 and spl 3.04.0000
Anyone with any further help - ordered a new Touch HD but I need to get this one up and running
Thanks

have you tried sd card flash
make sure you put the orignal rom on the root of a none sdhc card (1gb or smaller) and is renamed to "Arteimg.nbh"
official wm5 rom
official wm6 rom
Simply put the phone in bootloader with your 'boot' card inserted and follow the instructions.

Spikez.....I've tried that before. It reads from the SD card....goes through the motions, and then provides an error after about 5-10mins saying "SD FAT update failed"
Any ideas...please reply if only to say "no chance mate"
Thanks for any help you can give me.

i still guess yours is more likely to be fixed than mine as mine just goes straight to the rgb screen can you take a picture of what appears on your screen.
Try use an none offical rom and does your artemis ask you to "update sd image press this key to start download"

unfortunately i've left my digi cam at work I can explain rather well though, bear with me:
I reset the device with SD card in and I get a white screen saying "Checking SD Card" - there is then an arrow asking me to hit volume key to flash...I do that.
I get 5 mins of "Reading from SD" at the bottom of the white screen. Following that I get a "verifying certificate" message and then about 10seconds later a "SD FAT update failed!!!" message...it then just sits there until I press a key on the device and then it falls back to bootloader (multi coloured screen)
this MUST be fixable by somebody who isn't a noob like me - any ideas?

either try add these files into root of sd card
Enterbootloader.exe
rapitool.exe
RomUpdateUtility.exe
RUUGetInfo.exe
RUUREsource.dll
RUU_USPL_Signed.nbh, and
"Arteimg.nbh"
or try once in bootloader plug in usb and try using a ruu

files didn't work...just went straight through to bootloader as opposed to reading SD card. As for launching the RUU through windows...didn't work either. Bombed out after 5% with a "FLASH WRITE " error

Wiggz said:
My IPL SPL is currently 1.25.0001/1.25.0.000 but when i attempt to flash with official rom (!) it moves to the same as spikez - ipl 3.04.0001 and spl 3.04.0000
Thanks
Click to expand...
Click to collapse
as your ipl and spl is so high i guess you may have a Brick i cant seem to get my one working either as i earlier stated it is very common that people with this ipl and spl cant seem to get theirs back working.

spikez93 said:
as your ipl and spl is so high i guess you may have a Brick i cant seem to get my one working either as i earlier stated it is very common that people with this ipl and spl cant seem to get theirs back working.
Click to expand...
Click to collapse
True but as can be seen from that post...mine shifts from 1.25 to 3.04 depending on the flash attempt?

my best suggestion to you is stick with it. Try read through this sign up and post here andrew, bill, [email protected] and noney82 very helpful read through see if that post is any use.