I'm having a mare....my Artemis has died after a hard reset - just sits at bootloader. I can't flash any rom at all using RUU. All cooked roms fail after 3% with a "image corrupt" error and all original roms (wm5 and wm6 for o2 orbit) fail after 5% with "Flash Write" error.
I've also tried flashing from SD card....starts...but then fails on the validating certificate with an "SD FAT error" or sorts.
I know it's probably salvagable as I can get into bootloader....any ideas? People on forums are telling me to unlock using USPL...but because i cant get into the os to get activesync....it won't work.
a simular thing happens to me my one sits in a rgb screen and says ipl 3.04.0001 and spl 3.04.0000. none of the roms i used work ive just decided to leave it. if your ipl and spl is lower than mine i guess you will be more likley to get working again as people with the same ipl and spl as me cant get their one working
Try to go to bootloader and try to use it :
http://forum.xda-developers.com/showthread.php?t=311403
If it work try to flash with any custums roms.
If you don't have this , you only can flash with officials roms. That's why you can't flash with custums roms
Qui-Gon Ginn said:
Try to go to bootloader and try to use it :
http://forum.xda-developers.com/showthread.php?t=311403
If it work try to flash with any custums roms.
If you don't have this , you only can flash with officials roms. That's why you can't flash with custums roms
Click to expand...
Click to collapse
Thanks for this however I;ve been directed to that thread before and each time it's pointless. There is no point me attempting to USPL my device when I can't get an activesync connection due to the fact it has no OS bootable.
As for the official Roms...I've tried the ones that have been touted as official for the Orbit but with no effect.
My IPL SPL is currently 1.25.0001/1.25.0.000 but when i attempt to flash with official rom (!) it moves to the same as spikez - ipl 3.04.0001 and spl 3.04.0000
Anyone with any further help - ordered a new Touch HD but I need to get this one up and running
Thanks
have you tried sd card flash
make sure you put the orignal rom on the root of a none sdhc card (1gb or smaller) and is renamed to "Arteimg.nbh"
official wm5 rom
official wm6 rom
Simply put the phone in bootloader with your 'boot' card inserted and follow the instructions.
Spikez.....I've tried that before. It reads from the SD card....goes through the motions, and then provides an error after about 5-10mins saying "SD FAT update failed"
Any ideas...please reply if only to say "no chance mate"
Thanks for any help you can give me.
i still guess yours is more likely to be fixed than mine as mine just goes straight to the rgb screen can you take a picture of what appears on your screen.
Try use an none offical rom and does your artemis ask you to "update sd image press this key to start download"
unfortunately i've left my digi cam at work I can explain rather well though, bear with me:
I reset the device with SD card in and I get a white screen saying "Checking SD Card" - there is then an arrow asking me to hit volume key to flash...I do that.
I get 5 mins of "Reading from SD" at the bottom of the white screen. Following that I get a "verifying certificate" message and then about 10seconds later a "SD FAT update failed!!!" message...it then just sits there until I press a key on the device and then it falls back to bootloader (multi coloured screen)
this MUST be fixable by somebody who isn't a noob like me - any ideas?
either try add these files into root of sd card
Enterbootloader.exe
rapitool.exe
RomUpdateUtility.exe
RUUGetInfo.exe
RUUREsource.dll
RUU_USPL_Signed.nbh, and
"Arteimg.nbh"
or try once in bootloader plug in usb and try using a ruu
files didn't work...just went straight through to bootloader as opposed to reading SD card. As for launching the RUU through windows...didn't work either. Bombed out after 5% with a "FLASH WRITE " error
Wiggz said:
My IPL SPL is currently 1.25.0001/1.25.0.000 but when i attempt to flash with official rom (!) it moves to the same as spikez - ipl 3.04.0001 and spl 3.04.0000
Thanks
Click to expand...
Click to collapse
as your ipl and spl is so high i guess you may have a Brick i cant seem to get my one working either as i earlier stated it is very common that people with this ipl and spl cant seem to get theirs back working.
spikez93 said:
as your ipl and spl is so high i guess you may have a Brick i cant seem to get my one working either as i earlier stated it is very common that people with this ipl and spl cant seem to get theirs back working.
Click to expand...
Click to collapse
True but as can be seen from that post...mine shifts from 1.25 to 3.04 depending on the flash attempt?
my best suggestion to you is stick with it. Try read through this sign up and post here andrew, bill, [email protected] and noney82 very helpful read through see if that post is any use.
Related
Hi all thanks for looking at my thread.
I'm try to upgrade my Dopod D810 and i encounted a problem and would really like some help here.
The steps i thought i should take were the following
Run...
Unlock and CID Unlock
HardSPL
Radio
ROM
However, after running the Unlock and CID Unlock, i tried to run HardSPL.
But i come accross the "ERROR [246] DEVICE NOT RESPONDING" when i run the ROm update utility.
On the PDA with the 3 color screen
TRIN100
IPL-SSPL by Des
TIN100
SPL - 1.07.ds
and in the white "USB"
what have i done wrong? should i have no ran the UNLOCK and CID Unlock? if so how do i revert this? and what are the correct steps to take to upgrade this?
I am a hermes user and i've done exactly what i did to my hermes to his one.
Please help me.
Kind Regards,
Jason
---------------------------------
guys please, i tired reading the wiki and it told me to run SSPL-TRIN on my device.
i ran it, tired running the utilites again and i get the same problem.
the wiki and text documents says that as long as my SPL ends in a ".ds" i should be able to flash any rom without a problem but i still cant.
all i want is to have a english ROM and the current radio
please help masters. i keep getting "ERROR [246] DEVICE NOT RESPONDING" when i try to flash LVSW lastest rom.
kind regards,
jason
----------
I have been able to upgrade the radio to 1.41.
but i still get ERROR 246 when i try to upgrade the ROM or HardSPL
I'm waiting for help and will be very greatful when someone responds.
Kindest regards,
Jason
have you tried to run the RUU again (leaving the device connected in bootloader, tri colour screen) after you get the error?
Same problem here...
Alternative flashing method.
I just can tell I success using MiniSD with TRINIMG.nbh and execute SSPL-TRIN.exe to flash it. Hope this help. Read Wiki for details.
EDIT
ok i understand that you are suggesting that i use my SD card to Flash the ROM in.
If this is successful i will be greatful but will i have to do this everytime from now on rather than through the computer?
jason
racerx_ said:
have you tried to run the RUU again (leaving the device connected in bootloader, tri colour screen) after you get the error?
Click to expand...
Click to collapse
Ok so i've tried to flash a ROM/HardSPL using the SD card.
i;ve rename the file to TRINIMG.nbh
and then i;ve loaded it in to the bootloader.
however i get a quick flash of a grey background with the word "Loading" and then it just goes to the tri color screen and nothing happens.
the Tricolor screen shows
TRIN100
IPL-0.50
TRIN100
SPL-1.20.Olipro
(white area) Serial(or USB)
Please someone help me out.
a member has mentioned that it is because i do not have Super CID and i should run the unlock. but i have done so.
please guru's of trinity! help me!!!
Personally, I've never been able to flash my phone from the SD card. Never tried before Hard-SPL, but certainly since it just does not work. Need a Windows XP machine (my vista 64 bit won't work - can't find the 64 bit driver for USB bootloader mode). Find yourself a windows pc!
nealed said:
Personally, I've never been able to flash my phone from the SD card. Never tried before Hard-SPL, but certainly since it just does not work. Need a Windows XP machine (my vista 64 bit won't work - can't find the 64 bit driver for USB bootloader mode). Find yourself a windows pc!
Click to expand...
Click to collapse
My attempts with the SD have not work, when i put the SD card in and put it in to boot loader, i get a quick flash of Loading and its just stuck on the tricolor displaying
TRIN100
IPL-0.50 (could this be the problem?)
TRIN100
SPL - 1.20.Olipro
(white area) serial
i do have a windows XP home machine.
man this is stressing me out. please guru's help me out
ok i dont know how but i've some how been able to upgrade to the lastest LVSW. there is a god (i've always known)
how i did this was i was trying to run HardSPL again. It went in to the bootmode while the Utitlty on the computer gave ERROR 246.
So i thought i'd run LVSW, and what do you know? it work! and upgraded!
the question i have is
when i load the bootloader screen i get
TRIN100
IPL - 0.50
TRIN100
SPL - 1.20. Olipro
but then ERROR 246 occurs
i get
TRIN100
IPL-SSPL by Des
TIN100
SPL - 1.07.ds
So does anyone know what is wrong with my Trinty?
What do you bootloaders show?
---------------------------------
edit.
i;ve also noticed that after successful being able to upgrade to LVSW when i look at device info.
my radio hasnt actually upgraded, but back when i wasnt able to upgrade the rom it said i had 1.41.
but now i only have radio 1.16. but i have been able to upgrade to radio 1.41. now.
I just use TRIN-SSPL.exe and make it go into SuperCID Bootloader mode. Then it ask me to confirm whether I want to flash it, press [Power] to continue and it work.
MJRL said:
Same problem here...
Click to expand...
Click to collapse
are you using xp or vista? If you have vista try that on a windows xp machine. I have seen that many time on my p3600.
Just my 2 cents
First time with vista, but after read so many problems with vista i've tried with xp, but gave same error has jasonchiu, i'll try has he did,ignoring the error
Is it possible that other files on the MiniSD?
Try format the memory card and write the files.
I am running Vista so this the only way for me,
I used this method to flash WM5 and WM6.
On the memory card, only
TRIN-SSPL.exe and TRINIMG.nbh
and the device is not SuperCID.
I updated my rom from the original spanish version to a Artemis_Touch_3.01
After some use, the device is blocked.
It starts the HArd reset, after "Format messages" It starts HTC white screen
IPL 3.13.0001
SPL 3.13.0000
and nothing more
.
It also works ROM update mode (Three colors screen) but when I execute the Rom update frommy pc, it reaches 2/3% and gives different Errors depending the ROM,
"Ivalid Vender ID [294] when I use the ROM HTC_P3300_SPA_3.13.412.1_4.1.13.44_02.94.90_Ship_R
ERROR [270]: Update Error -The Image File is corrupted - When I use Black & Blue 4.3 or Artemis_Touch_3.01
I need help!!!
brick?
hello,
First you must open the bootloader menu,
hold voice dial button and press soft reset.
If this not working hold voice dial and on/off button and softreset.
You must connect first your htc with your pc and the start the bootloader.
When you are in the bootloader menu, you can upload an orginal fabricrom to your htc.
Search xda-developer for the fabric rom.
And then you can change your rom for something else but don't forget the uspl.
When you want to change image you must install the uspl first otherwise everthing will blocked
the problem you have is that you have to run the uspl first before you can flash another firmware. If you run the uspl you will see that the spl loader of your device is version 1.11.000 and than you can flash an other rom of your choice
greetzz Patrick
uspl does not work. this is the point you can not get it.
have a problem but I cannot find anything useful for my case, maybe you can help me?
pvdhelm said:
the problem you have is that you have to run the uspl first before you can flash another firmware. If you run the uspl you will see that the spl loader of your device is version 1.11.000 and than you can flash an other rom of your choice
greetzz Patrick
Click to expand...
Click to collapse
Hi Patrick,
I have a dutch rom on my htc P3300
IPL: 1.12.0001
SPL: 1.12.0000
GSM: 02.67.90
os: 1.12.0.0
my HTC remains stuck on the startup screen (logo HTC) and will not get any further.
Connection with active synch is not possible, ans holding the buttons reset-voice rec-on/off buttons don't react. WM cannot be started in that way.
is it possible to find a boot program which allows me to start up WM again like a regular PC? something like a emergency startup disk? I have a 2GB micro SD card. After reading and trying so many things, I lost the way in this site and was hoping maybe you can send me some useful links that can solve my problem? I would appriciate the effort.I don't know if it's allowed to send my personal emailadress? If it is allowed please let me know. Maybe we can exchange directly some info, otherwise I don't have a problem mailing this site.
(I hope I can find this thread again after closing?)
Kind regards , Eli
my artemis is also in the same state
Hi All,
Please help me with problem which I am facing with my HTC P3300
When i switch it on..Its stuck in the state where it shows
IPL 3.07.0001
SPL 1.11.0000
GSM 03.08.90
OS 3.4.0.0
What I tried.
1. I tried USPL , its not loading as device is not getting detected in my laptop.
2. Volume Down+Reset is not working
Please help me with this
Hello !
First, sorry for my english.
Then, my SPV M650 (Artemis) is bricked.
It shows "Searching for SD Card" and still stay on the bootloader screen (the muticolor screen) and nothing else.
On the bootloader scren I can see the IPL and the SPL numbers :
IPL: 3.13.0001
SPL: 3.13.0000
When I connect the phone via an USB cable, on the phone screen I've got a "USB" item appears at bottom left and Windows XP see a pocket PC connected (but not activesynced).
When I tried to reflash it with the RUU tool, I always got an error 260.
The RUU tool can't connect to my phone.
For me, the SPL is not good but I don't know how to change it with my phone in this state.
I tried to flash it directly with a 2GB SD card (FAT32 formated) with only a ".nbh" file at the root directory but it don't work.
If someone got an idea... I will take it with pleasure...
Thank you for your help.
Hi,
Are you following these instructions:
http://wiki.xda-developers.com/index.php?pagename=Artemis_SD_Card_Flashing
I see from your SPL that you are not using the USPL so your flash image would have to be your original unmodified SPV M650 flash image. The name of the image file must be ARTEIMG.nbh or it will not be found.
Hope that this helps,
Matt.
Thank you for your help.
The phone is always on the boot loader but the flash with the original Orange ROM modified my IPL and my SPL (only after the second flash).
New IPL: 1.84.0001
New SPL: 1.84.0000
The flash not take 30min as follows in the wiki.
The steps during the falsh are :
- Checking SD Card
- Validation
- Formating BINFS (1s)
- Reading from SD (5min)
- Verifying certificate (5s)
- Flashing EXTROM (1s)
- Flashing GSM CODE (1s)
- Flashing first phase OS (10s)
- Reading second OS from SD! (5min)
- Flashing second phase OS (3s)
- Success. Press any key.
=> Back to bootloader.
So the phone still bricked.
It seems that you have now a working IPL, so now try to flash the USPL, after that your phone should have SPL 1.11.000 (or so )
Link: http://forum.xda-developers.com/showthread.php?t=311403
After that you should be able to flash any ROM you like.
Don´t forget to first flash a Radio!
Link: http://wiki.xda-developers.com/index.php?pagename=Artemis_RadioUpgrades
Good luck!
Thank you four your help mat2206.
But how can I flash USPL with a bricked phone ?
From SD card it's not work. I get a "Invalid certificate" error.
And for flash a new radio or ROM version, I will need the USPL...
Any ideas ?
Damned !
I find the way to flash USPL.
But I've got an 270 error when I did it at 99% of the flash.
Now the phone don't turn on. Not feels good...
Any ideas ?
drummer01 said:
I find the way to flash USPL.
But I've got an 270 error when I did it at 99% of the flash.
Now the phone don't turn on. Not feels good...
Any ideas ?
Click to expand...
Click to collapse
You need HTC assistence! You have damaged the SPL and now the phone is died!
You can't power on, you can't start bootloader, you can't do anything...
HTC Assistence
cesconoa said:
You need HTC assistence! You have damaged the SPL and now the phone is died!
You can't power on, you can't start bootloader, you can't do anything...
Click to expand...
Click to collapse
Thank you for this news.
But the phone is not under guarantee.
And I don't want to pay much money for unbrick my phone...
drummer01 said:
Thank you for this news.
But the phone is not under guarantee.
And I don't want to pay much money for unbrick my phone...
Click to expand...
Click to collapse
I hope you find a solution, I don't know if it's a way to write the rom without bootloader (something like JTAG)...
I've read a way in the assistence manual, but you need a particolar sim card...
Hi,
I'm using Artemis with one of Tom's ROM. The device was working well. But today suddenly the device won't start up - it is locked at the startup screen showing the SPL, IPL etc. I can enter the bootloader.
Can anybody tell me how to flash the ROM at this stage?
Flash from bootloader
Hi!
Please download an official rom and keep pressed the Power and Record buttons. You will see a screen with 3 colors (red green blue). Connect the USB cable and wait for Activesync. After this start the original rom flasher and follow the instructions. If you can start the Windows, you should flash the USPL again and you can flash cooked roms. If you flashed a new one, i think you should also upgrade the radio rom.
Sorry for my English
well i'll give it a try.
BTW will activesync work if the phone is not booting up?
sure it will, but make sure you have the only phone pluged in, nothing else, and disable all firewalls and antivriuses.
Good luck
i flashed with htc official rom and it worked first. after soft resetting a few time (due to program installation) the phone again back to earlier state.
it is showing:
ipl 3.13.0001
spl 3.13.0000
gsm 2.94.90
os 3.13.0.0
and stuck at this screen.
i tried to update the phone again with the same rom - but i'm getting error 270.
do i need to unlock cid before flashing?
but i can't use the uspl tool as i can't connect to activesync.
pls help.
make sure the battery is fully charged again.
Restart your PC, isbale ll antivirus and firewalls
Better if flashing in XP PC
put PPC in Boating status
Flash Shipped ROM
Specify which software caused you the trouble and do not install it again
CID unlock PPC
Flash any cooked ROM.
once i flashed the phone with the shipped rom successfully. The phone was CID unlocked then. But now when I try to flash the shipped again i'm getting an error message (error 292 or something - stating-invalid vendor id)
archat68 said:
once i flashed the phone with the shipped rom successfully. The phone was CID unlocked then. But now when I try to flash the shipped again i'm getting an error message (error 292 or something - stating-invalid vendor id)
Click to expand...
Click to collapse
you must unlock phone again.
I tried flashing the device with factory shipped ROM. but i'm getting Error 294-invalid vendor id message.
please suggest what to do?
chance are you have stuffed your bootloader...
start from scratch again by running uspl:
http://forum.xda-developers.com/showthread.php?t=311403
than flash your favorite rom again, ideally via sd-card-flashing:
http://wiki.xda-developers.com/index.php?pagename=Artemis_SD_Card_Flashing
greetz
thormdac said:
chance are you have stuffed your bootloader...
start from scratch again by running uspl:
http://forum.xda-developers.com/showthread.php?t=311403
than flash your favorite rom again, ideally via sd-card-flashing:
http://wiki.xda-developers.com/index.php?pagename=Artemis_SD_Card_Flashing
greetz
Click to expand...
Click to collapse
USPL needs activesync running. Can you tell me how to run USPL when I can't boot into windows?
well,
its been some time, but i am pretty sure uspl puts your device into bootloader and operates from there...
have you tried setting it into bootloader, connecting via usb and simply starting uspl?
running a normal setup-routine, there is no need to start it from wm either-simply put it into bootloader and start setup!
greetz
Well i tried that. But it seems that USPL doesn't work without activesync.
i've also tried flashing with SD card, but after a brief "Checking SD card content" message the phone goes back to bootloader.
Someone helpppp pls.
are u sure your sd card is correctly configured, according to the wiki entry- especially part "if above fails" ...?
if all steps fail, assumed you performed them correctly, you might try taking out battery and leave the device fully without power overnight...and restart it the next morning
I've used a 512MB SD card - formatted it- and copied the OS file as ARTEIMG.nbh - put the sd card in the phone and started the phone in bootloader mode.
I think there is nothing more to do.
I can enter the bootloader, connect the phone to PC in USB mode. So, I hope that my phone is not bricked.
But how to revive it?
if you are in bootloader, i dont see why you shouldnt be able to flash!!!
try another sd-card, use another xp computer, exchange the usb cable...
yust to be certain: have you left out battery over-night?
...and what are the details stated on boot-loader screen (numbers)?
oh, and I get the feeling you are not working exactly as told:
in your PC right-click on Computer, then select Manage
Select Disk Manager and then delete existing partition
create a new partition with max size 256MB
format this partition in FAT32
thormdac said:
(i)...and what are the details stated on boot-loader screen (numbers)?
(ii) oh, and I get the feeling you are not working exactly as told:
in your PC right-click on Computer, then select Manage
Select Disk Manager and then delete existing partition
create a new partition with max size 256MB
format this partition in FAT32
Click to expand...
Click to collapse
(i) See post no 5 for the details
(ii) You can not do this with a removable disk (SD card inserted through a card reader). Only works when you can get WM5Storage to work.
archat68 said:
(ii) You can not do this with a removable disk (SD card inserted through a card reader). Only works when you can get WM5Storage to work.
Click to expand...
Click to collapse
...i dont have my micro-sd-card-adapter at hand atm., but there sure will be possibilities formatting your sd card accordingly...try administrative tools/computermanagement/storage/diskmanagement under xp, boot your pc with a diskpartitioner like acronis disk director...
i can only advise you to keep trying...but as long as you can not say for sure sd-card-flashing is working correctly, i wouldnt give up...
and as far as flshing bootloader via usb/activesync goes, i can only say i once screwed my device due to insufficiant battery power during sd-card-flashing and thought it was bricked just at the point you are stuck now!!! - totally resetting it with the power-oiut-method, i.e. battery out overnight, revived it!!!
than agin i sure as hell did everything the way it was ment o be done...and nothing worked until i switched to another pc/ usb-cable!!!
so, to sum it up, DONT GIVE UP!!! bootloader is showing...so there must be a way to get this to work...
greetz
archat68 said:
I tried flashing the device with factory shipped ROM. but i'm getting Error 294-invalid vendor id message.
please suggest what to do?
Click to expand...
Click to collapse
Somebody please help me to revive my phone.
how can we help you, if you dont provide us any results of the steps suggested to you...ideally in a way so we can see what you actually did or didnt do, precisely as told ?!?
greetz
Upgrade to Hard-SPL Olipro 1.20 - USB or SD Just Added SD Card Method at Bottom of this Post
10 Step Program
Pulled from Website dated: Monday August 06, 2007 by ??? if someone knows, I'll give credit.
Recovered and Updated Monday October 27, 2009 by SuperSport
because the WiKi has vanished
Hard SPL will allow you to flash cooked ROMs without SuperCID’ing your device and also will protect your device from being bricked in a bad flash. If a bad flash occurs it should remain in bootloader, and you can re-flash another ROM.
Caution!!! Flashing Hard-SPL will Probably Hard Reset your device!!!! Backup all data FIRST!!!
Before you proceed, check which SPL is on your device:
*** Enter Tri Color Screen ***
--Unplug your phone from USB - Helps to avoid freezing USB Ports
--Hold down the Power & Camera Buttons
--While still holding them down, press the Reset Button using the Stylus
--Release the Reset Button, but continue to hold the Power/Camera buttons until you see the Tri Color Screen
*** Enter Tri Color Screen ***
If your SPL is 1.30.Olipro, 1.20.Olipro, or 9.99 CP, then you already have Hard-SPL on your device and can skip flashing HardSPL, although, I recommend using Olipro 1.20 to avoid problems.
If you want to continue flashing Olipro HardSPL 1.20:
Press the Reset Button using your Stylus. Wait for your phone to start back into Windows. Plug the USB Cable into your phone and PC. Verify ActiveSync or WMDC is connected properly. Now you can Flash.
1. Download "Olipro HardSPL 1.20.zip" in attachment below
2. Unzip the Files, and Run the Program "Olipro HardSPL 1.20.exe" This is a small AutoFlash file I created using Olipro 1.20
3. Windows Vista and Windows 7 may confirm you want to run the program. Choose YES.
4. Check the check box, click ‘Next’
5. Also Check this check box, click ‘Next’
6. In the next window, click the ‘Update’ button
This will show the version number of the ROM, radio, or in this case bootloader that you are about to flash.
7. After the version number has appeared, click 'Next'
8. In the following window, click ‘Next’, your phone may ask if it's ok to run the program, Tap 'Yes'.
(After you click this, the flash will begin, so do not disconnect your device or do anything on your computer)
9. A Progress bar will appear on your computer screen, and your trinity will display a grey screen with progress bar. Be patient while your device is being updated. This will only take a moment.
10. Once your device is finished updating, if it did not automatically soft reset, Press the Reset Button with the Stylus. Click the ‘Finish’ button to exit the RUU program.
To confirm Hard-SPL is on your device, re-enter Tri Color Screen following directions above. You should see the following:
Hard SPL 1.20.Olipro
TRIN100
IPL-0.50 (your device may show IPL-1.00)
TRIN100 MFG
SPL-1.20.Olipro
CONGRATULATIONS!! You have now installed Olipro's Hard-SPL 1.20 on your device using USB Method!! Press the Reset Button with your Stylus to restart.
**********************************
Alternate SD Card Method
**********************************
For those who would rather use their SD Card for this (Maybe your USB Port is not functioning). For this method, the way I'm describing, your phone must be running a version of Windows Mobile. Can be any Version, 5-7. If your phone does not currently run, flash back the OEM ROM that came with it Originally. You can find some in my signature.
Caution!!! Flashing Hard-SPL may Hard Reset your device!!!! Backup all data FIRST!!!
1. Be sure you have a, Non-SDHC, SD Memory Card.
2. Be sure the card is formatted Fat32 and Without a Label.
3. Download the attached HardSPL SD.zip file and extract it's contents. Copy both files, SSPL-TRIN.exe and TRINIMG.nbh, to the Root of your SD Card.
4. On your phone, use File Explorer to browse to the Root of your SD Card.
5. Tap the SSPL-TRIN.exe file. This should run the file.
6. On some phones, you will see a security message come up. Select 'Yes' to run the program.
7. You should now see a Grey screen with Blue Lettering. It will be asking you to Press power button. Go ahead and press the power button.
8. You will see the update progress for a short moment, it will restart, and update again, then show "Update Complete - UPDATE SUCCESS" If you see this message, it has worked.
9. Press the Reset Button with your Stylus to Restart
10. Delete the two files from your SD Card (TRINIMG.nbh, SSPL_TRIN.exe). To confirm Hard-SPL is on your device, Enter Tri Color Screen following directions above. You should see the following:
Hard SPL 1.20.Olipro
TRIN100
IPL-0.50 (your device may show IPL-1.00)
TRIN100 MFG
SPL-1.20.Olipro
CONGRATULATIONS!! You have now installed Olipro's Hard-SPL 1.20 on your device using SD Method!! Press the Reset Button with your Stylus to restart.
Maybe if this could be Stickied?
Thanks, it's a very nice guide for Trinty users, clean and detailed, I also recommand using Olipro 1.20 and not 1.30 to avoid problems, especially with 6.5 roms the annoying "WLAN ERRROR" sometimes seen in bootloader mode ...
Yes, make this "Sticky"
Brds,
nAr
Thanks narshorn! Someone else posted this a long time ago on a WiKi I believe, and I just recovered what I could of the original web page and then rewrote it to work with my files. The original page was removed from it's server, so I grabbed as much of the cached version of it as I could, thus, I don't know who did the original.
Also, thank you for the confirmation of using Olipro 1.20 and not 1.30. That was my belief, and I've heard others, but I'm glad you confirmed.
noob here, need help on flash HardSPL.
i encounter error when trying to update my hardSPL. when i try to flash when my phone is tri color screen mode, this error pop out.
ERROR [270]:UPDATE ERROR
The image file is corrupted. please check your update utility.
info update:
at last i manage to flash my phone to hardspl 1.20, i boot my d810 in normal mode, establish active connection with window, then the flash carry on without any error. but the phone hard reset
but, i wonder y i cant flash to hardspl in tri color screen ???
update to 1.20 spl Olipro true sd card not USB
hi and Thanks for so nice explanation. there is a way to update spl with sd card? my USB connection is faulty. if s/o know please let me know how.
tzuki1 said:
hi and Thanks for so nice explanation. there is a way to update spl with sd card? my USB connection is faulty. if s/o know please let me know how.
Click to expand...
Click to collapse
Just added SD Method to bottom of post #1. Good Luck!
thongkh said:
noob here, need help on flash HardSPL.
i encounter error when trying to update my hardSPL. when i try to flash when my phone is tri color screen mode, this error pop out.
ERROR [270]:UPDATE ERROR
The image file is corrupted. please check your update utility.
info update:
at last i manage to flash my phone to hardspl 1.20, i boot my d810 in normal mode, establish active connection with window, then the flash carry on without any error. but the phone hard reset
but, i wonder y i cant flash to hardspl in tri color screen ???
Click to expand...
Click to collapse
Because stupid me forgot that if you don't have HardSPL on your phone, then TRI COLOR SCREEN flashing is not possible. Doh! FIXED above.
Thank you for bringing this to my attention. When I physically went through the steps, I forgot I still had HardSPL on my phone from previous.
I just went through the steps AGAIN after removing HardSPL, and verifed it works correctly as listed in Post #1.
thankz for promptly reply
btw, what d diff between HardSPL 1.20 and 1.30?
thongkh said:
thankz for promptly reply
btw, what d diff between HardSPL 1.20 and 1.30?
Click to expand...
Click to collapse
I've seen many reports that 1.30 caused issues. Olipro, 'the guy who made our Trinity's safe for Flashing', stopped updating the thread, but if you read it, you will find many users reporting problems and asking for the thread to be updated to go back to 1.20.
I've been using 1.20 since it was released, and have NEVER had a problem with it. And believe me, I Flash a LOT!!! I'm expecting my poor Trinity to catch fire any day now.
Oh... Thx for the tutor...that what i need now...
Good job someone remembered howto
Thanks for the reminder - managed to forget how to enter tri-colour screen in the three months since I last reflashed.
I need help here
I have tried each of the methods.
though your explanation and step by step instructins are very clear, istill can't seem to get Olipro's HSPL on my phone. in the case of using active sync, after it enters the tri color screen nothing happens again and the i get an error message (ERROR 260).
When i tried using the SD method, when i tapped the SSPL_TRIN file, it goes stright to the tri color screen ths is the information i have there
TRIN100
IPL-SSPL by Des
TRIN100
SPL-1.07.ds
and for this reason i can seem to flash any rom with success each time it only gets to the tri colou screen and i get the ERROR 260 message.
Anyone with any idea on how i can fix this.
thanks in advance
redoxy said:
I need help here
I have tried each of the methods.
though your explanation and step by step instructins are very clear, istill can't seem to get Olipro's HSPL on my phone. in the case of using active sync, after it enters the tri color screen nothing happens again and the i get an error message (ERROR 260).
When i tried using the SD method, when i tapped the SSPL_TRIN file, it goes stright to the tri color screen ths is the information i have there
TRIN100
IPL-SSPL by Des
TRIN100
SPL-1.07.ds
and for this reason i can seem to flash any rom with success each time it only gets to the tri colou screen and i get the ERROR 260 message.
Anyone with any idea on how i can fix this.
thanks in advance
Click to expand...
Click to collapse
Did you copy the TRINIMG.nbh file to your SD Card also? Was your SD Card formatted FAT32 and No Label?
Using the SD Method, you do not need to be connected to your Computer. Copy both files to SD and do all work from phone.
Let me know if that works or not.
Remove the HARDSPL...
Hi,
How can I remove the HARDSPL from my Trinity and go back to the original?! Thanks!
sergiopedro said:
Hi,
How can I remove the HARDSPL from my Trinity and go back to the original?! Thanks!
Click to expand...
Click to collapse
Only do this if you do not plan to flash any more Custom ROMs, and would like to stick with the OEM ROM (You may Brick your Phone if you flash from the Stock SPL):
Download the "HardSPL SD.zip " file from the first post.
Extract the files
Copy ONLY the "SSPL_TRIN.exe" file to your SD Card.
Run the "SSPL_TRIN.exe" file from your SD Card (This puts your phone into a special mode that will allow the HardSPL to be overwritten)
Now, your phone should be in bootloader mode with:
TRIN100
IPL_SSPL by Des
TRIN100
SPL_1.07.ds
At this point, you can flash your OEM ROM that includes the Original SPL and IPL.
I use this one: http://www.mediafire.com/?v5yjt1zvgjm
Hi all
I have tried to flash with usb but i'm having a problem
i'm using active sync and after i click 'execute' at the mobile screen it enters the tri color screen and it disconnects the usb port. I get an error message (ERROR 246) that says the device is not responding.
I've tryed several times and it has the same behavior...
The tricolor screen shows this message:
TRIN100
IPL-SSPL by Des
TRIN100
SPL-1.07.ds
i havent try the sd method because i dont have a sd card right now...
Thank you
rcpamr said:
Hi all
I have tried to flash with usb but i'm having a problem
i'm using active sync and after i click 'execute' at the mobile screen it enters the tri color screen and it disconnects the usb port. I get an error message (ERROR 246) that says the device is not responding.
I've tryed several times and it has the same behavior...
The tricolor screen shows this message:
TRIN100
IPL-SSPL by Des
TRIN100
SPL-1.07.ds
i havent try the sd method because i dont have a sd card right now...
Thank you
Click to expand...
Click to collapse
Your mobile screen is showing the correct information, with the exception of USB not showing. As soon as you get to the Tri Color Screen, try removing then reconnecting the USB connection and see if that makes any difference.
Also, when the Tri Color Screen comes up, does your computer ask to install a driver? If it does, be sure to allow that.
SuperSport said:
Your mobile screen is showing the correct information, with the exception of USB not showing. As soon as you get to the Tri Color Screen, try removing then reconnecting the USB connection and see if that makes any difference.
Also, when the Tri Color Screen comes up, does your computer ask to install a driver? If it does, be sure to allow that.
Click to expand...
Click to collapse
Well i just trying all steps again and it worked just fine...go figure!
Thank u anyway
rcpamr said:
Well i just trying all steps again and it worked just fine...go figure!
Thank u anyway
Click to expand...
Click to collapse
Glad to hear you are going. Now you are safe to flash custom ROMs.
Also, remember that each time you flash back to the OEM ROM for any reason, it replaces the HardSPL with the stock one. You will then need to flash the HardSPL back again. At least this is the case for the OEM that I use.
SuperSport said:
Glad to hear you are going. Now you are safe to flash custom ROMs.
Also, remember that each time you flash back to the OEM ROM for any reason, it replaces the HardSPL with the stock one. You will then need to flash the HardSPL back again. At least this is the case for the OEM that I use.
Click to expand...
Click to collapse
ok. thank u so much!