Develop Bugs

Brick Hermes, stuck at WM6 Screen, help!

Recently tried upgrading my SPV M3100 from WM5 to black WM6. Everything was going fine and I had installed the following
SPL (Bootloader) version 2.10.Olipro (HardSPL v7)
Radio version 1.43.00.00 (optional)
Was updating to ROM version: Windows Mobile 6 LVSW 160607 when USB cable was disconnected before installation ands I am now left with WM6 screen only
Can anyone help?

If you stuck in the wm6 boot screen and have flashed HardSPL 2.10 already you can just enter the bootloader and reflash your ROM again. Why do you use nearly 6 months old ROM (LVSW)?

Did you try to reflash the ROM?
Just switch to the bootloader and run the update again.
If the updater is complaining about "Not able to do so" you might need another ROM, but that method worked to or three times for me.
Cheers,
Jago

tried raflashing but activesync won't pick up phone

you do not need active sync to pick it up. Just enter the bootloader and run RUU.

how do you reflash without activesync?

Read this:
http://wiki.xda-developers.com/index.php?pagename=Hermes_Unbrick

richard_g_johnston said:
how do you reflash without activesync?
Click to expand...
Click to collapse
Simply - flashing process itself is not done by the Active sync (its icon is grey when flashing). I have tried to flash a ROM this way and it works. You just have to input correct values to the RUU yourself. Bootloader is the tri color screen. You can access it by holding power and ok button while using the stylus to soft reset the device. Hermes will pick up the usb connection.

Please read the WIKI and flash an original WM6/WM5 rom before attempting to flash a cooked rom.. then make sure you know what you are doing before flashing the cooked.

tried both
http://wiki.xda-developers.com/index...Hermes_Unbrick
http://forum.xda-developers.com/showthread.php?t=286755
still no joy
my device
IPL-1.04
SPL-2.10.0lipro
how do u run RUU in bootloader mode?

richard_g_johnston said:
tried both
http://wiki.xda-developers.com/index...Hermes_Unbrick
http://forum.xda-developers.com/showthread.php?t=286755
still no joy
my device
IPL-1.04
SPL-2.10.0lipro
how do u run RUU in bootloader mode?
Click to expand...
Click to collapse
Put your device into bootloader mode.
Connect it via USB to your PC.
Run the RUU on your PC (like if you had Active sync working).
Flash the ROM.
(should work with all cooked ROMs)
Update: I tried it now with the Schaps 4.20 - it is working.

When you run ruu it should create ROMUpgradeUt.exe if it says it fails to find the device just run this. I usually take a copy before clicking to close the error box.

where do u locate RUU.exe
sorry I'm not an expert in this

RUUWrapper.exe should be in the folder with the image you are flashing. Sorry if I confused you saying ruu.

When you download the cooked rom it comes in rar or zip containing 2 files - one with extension .NBH and the second one is RUUWrapper.exe (resource upgrade unit), unpack them to one folder and run RUU.exe Be sure to flash only ROM for your device otherwise you will kill it for good.

tried running RUU but get error 260, i.e. cannot pick up phone on USB

See post 12

yeah, tried running ROMUpgradeUt.exe, but still no joy

markafreeman said:
See post 12
Click to expand...
Click to collapse
If this does not work for you - then you can use flashing from the SD card (no USB needed for this kind of flashing) . But try what markafreeman suggests first.

Lets try some troubleshooting:
Whne you connect your device in the bootloader (red green blue screen) to your pc what does it say?
In the white part of the screen on your device it should say USB - then it will work.
If not you can still try flashing the ROM from the SD card - you will need a card reader though for this kind of flashing.

FLASH disaster

I was becoming an expert in flashing...but the cable became undone during a flash :-(
Now it restarts to a blank screen with R1.50.08.11 / G32.83.7020 etc. but goes no further.
Computer no longer sees device.
Used hard keys to go into bootlocker. (IPL 0.50 / SPL- 1.07.000)
My VISTA :-( computer sees device.
Then try RUU, but this gives a 270 error.
Tried moving to XP, but the computer does not install the software for the USB port, so now the RUU gives 200 error. Arrgh.
Question: How to update from a very corrupted ROM? Or where can I find the drivers for the USB port, for XP. and if I do can I do the update from the hard bootlocker?
Any help really appreciated!
MS

Update
Found USB drivers for Windows XP
But getting identical problem as with Vista :-(
Device not seen unless in bootlocker mode.
RUU starts and after 1% quits with 270 error - image file corrupt.
Tried RUU a hard SPL (olipro) but same 270 error occured.
Help still needed...
MS

I think you have to flash original HTC rom prio to try other roms

i got a similar problem here, my vista can find trinity only when it is in bootloader mode.
my experience is that connect tinity to vista when it is in bootlader mode, then i can flash a new rom.
after that tinity can sync with vista only via bluetooth.
for your case, maybe you really need restore your trinity to official rom first.

sailer1983 said:
i got a similar problem here, my vista can find trinity only when it is in bootloader mode.
my experience is that connect tinity to vista when it is in bootlader mode, then i can flash a new rom.
after that tinity can sync with vista only via bluetooth.
for your case, maybe you really need restore your trinity to official rom first.
Click to expand...
Click to collapse
Maybe helps:
http://trinityguides.info/index.php?option=com_content&task=view&id=20&Itemid=66

The trinity upgrade guide does not help here.
I can connect to device I have sorted out all the VISTA and XP issues.
The problem is at 1% status the 270 error occurs.
The telephone is actuall a Swisscom 1510. Original ROM was lost in first flashing, have searched but not found official update.
Is there a mini-ROM or a windows WM5 lite ROM which may overwrite what happens while still using the hard bootloader?
MS

Use SD card method.
See wiki page.
Bye

Hi,
...or .... MTTY Procedure....
BYE, Bobo

Tried SD card method - nothing happens. Just sits in Bootloader :-(

Try this procedure
In windows Vista use the attached driver in order to recognize your Device.
If your device is already recognized from windows vista replace the drivers with the drivers in the zip drive.
You have to use the drivers in the attached file not the windows default drivers VERY IMPORTANT!!!
After your Windows vista recognized your device try to flash it
Cheers

Thanks for all the help....but still I am having no success.
The HTC trinity is recognised in both Vista and XP when I use bootloader. (ie HTC USB SYNCH in device manager. Without boot loader the device is more or less dead.
I tried the SD crard trick - nothing happens.
Tried mtty.exe - just get cannot open USB port (on both VISTA and XP).
Nevertheless, the bootloader sees the USB port and the RUU goes to 1% then stops so some communication is happening.
Any other ideas?
MS

The final and, j' m sure, the definitive solution:
Try this one http://forum.xda-developers.com/showthread.php?t=308691&highlight=stack+in+bootloader

Just before I try splxploit, as a note I got this out of mtty
Cmd>info 8
Block 0x0(0) is Reversed block
...
Block 0xC(12) is Reversed block
Block 0x335(821) is BAD block !!!
Seems my problem must be here. Is there another fix besides splxploit?
MS

Install Olipro hardspl 1.20.
Bye

Dear, carefully look that thread again. Stack overflow for Trinity.
It's all my advise. I think you don't do right "Stack method" to get out your problem.
Best regard.(rest calm and do it again).

Uhm, try to download some rom again? and try Rom NVID (no vendor ID) for example. ???

Quick update...
Tried SD card - get 00068002 loading .... then goes to IPL0.5 SPL 1.07
mtty info 8 shows bad blocks
task 2a doesn't clear bad blocks because of CID lock
Tried various hard-SPL OLIPRO 1.2 1.3 etc, to unlock CID - to no avail.
Can the CID not be unlocked through mtty?
MS

ManStan said:
Quick update...
Tried SD card - get 00068002 loading .... then goes to IPL0.5 SPL 1.07
mtty info 8 shows bad blocks
task 2a doesn't clear bad blocks because of CID lock
Tried various hard-SPL OLIPRO 1.2 1.3 etc, to unlock CID - to no avail.
Can the CID not be unlocked through mtty?
MS
Click to expand...
Click to collapse
So you haven't yet tried splxploit?

END of STORY
YESSS!
POF you are a genius - Splxpoilt worked a dream.
Had to run unbrick.bat once. Hit soft reset, and run again as explained in the readme.
This got a good SPL on the machine - then a standard RUU worked a dream.
At the same time I got the SD card update working too...
OK, OK, so I should have tried splxpoit earlier. But I think I had to do the rest first to understand what was going on.
Strange thing is if I look at my machine again under mtty, there is still the Bad block (821). Who cares, I am unbricked!!!
By the way, this board is just completely amazing.
THANKS TO ALL....

i have the same problem
could you help me . how did you repair your spv?

my ARTEMIS is blocked "BRICK" please help

I updated my rom from the original spanish version to a Artemis_Touch_3.01
After some use, the device is blocked.
It starts the HArd reset, after "Format messages" It starts HTC white screen
IPL 3.13.0001
SPL 3.13.0000
and nothing more
.
It also works ROM update mode (Three colors screen) but when I execute the Rom update frommy pc, it reaches 2/3% and gives different Errors depending the ROM,
"Ivalid Vender ID [294] when I use the ROM HTC_P3300_SPA_3.13.412.1_4.1.13.44_02.94.90_Ship_R
ERROR [270]: Update Error -The Image File is corrupted - When I use Black & Blue 4.3 or Artemis_Touch_3.01
I need help!!!

brick?
hello,
First you must open the bootloader menu,
hold voice dial button and press soft reset.
If this not working hold voice dial and on/off button and softreset.
You must connect first your htc with your pc and the start the bootloader.
When you are in the bootloader menu, you can upload an orginal fabricrom to your htc.
Search xda-developer for the fabric rom.
And then you can change your rom for something else but don't forget the uspl.
When you want to change image you must install the uspl first otherwise everthing will blocked

the problem you have is that you have to run the uspl first before you can flash another firmware. If you run the uspl you will see that the spl loader of your device is version 1.11.000 and than you can flash an other rom of your choice
greetzz Patrick

uspl does not work. this is the point you can not get it.

have a problem but I cannot find anything useful for my case, maybe you can help me?
pvdhelm said:
the problem you have is that you have to run the uspl first before you can flash another firmware. If you run the uspl you will see that the spl loader of your device is version 1.11.000 and than you can flash an other rom of your choice
greetzz Patrick
Click to expand...
Click to collapse
Hi Patrick,
I have a dutch rom on my htc P3300
IPL: 1.12.0001
SPL: 1.12.0000
GSM: 02.67.90
os: 1.12.0.0
my HTC remains stuck on the startup screen (logo HTC) and will not get any further.
Connection with active synch is not possible, ans holding the buttons reset-voice rec-on/off buttons don't react. WM cannot be started in that way.
is it possible to find a boot program which allows me to start up WM again like a regular PC? something like a emergency startup disk? I have a 2GB micro SD card. After reading and trying so many things, I lost the way in this site and was hoping maybe you can send me some useful links that can solve my problem? I would appriciate the effort.I don't know if it's allowed to send my personal emailadress? If it is allowed please let me know. Maybe we can exchange directly some info, otherwise I don't have a problem mailing this site.
(I hope I can find this thread again after closing?)
Kind regards , Eli

my artemis is also in the same state
Hi All,
Please help me with problem which I am facing with my HTC P3300
When i switch it on..Its stuck in the state where it shows
IPL 3.07.0001
SPL 1.11.0000
GSM 03.08.90
OS 3.4.0.0
What I tried.
1. I tried USPL , its not loading as device is not getting detected in my laptop.
2. Volume Down+Reset is not working
Please help me with this

LAST HOPE!

I'm having a mare....my Artemis has died after a hard reset - just sits at bootloader. I can't flash any rom at all using RUU. All cooked roms fail after 3% with a "image corrupt" error and all original roms (wm5 and wm6 for o2 orbit) fail after 5% with "Flash Write" error.
I've also tried flashing from SD card....starts...but then fails on the validating certificate with an "SD FAT error" or sorts.
I know it's probably salvagable as I can get into bootloader....any ideas? People on forums are telling me to unlock using USPL...but because i cant get into the os to get activesync....it won't work.

a simular thing happens to me my one sits in a rgb screen and says ipl 3.04.0001 and spl 3.04.0000. none of the roms i used work ive just decided to leave it. if your ipl and spl is lower than mine i guess you will be more likley to get working again as people with the same ipl and spl as me cant get their one working

Try to go to bootloader and try to use it :
http://forum.xda-developers.com/showthread.php?t=311403
If it work try to flash with any custums roms.
If you don't have this , you only can flash with officials roms. That's why you can't flash with custums roms

Qui-Gon Ginn said:
Try to go to bootloader and try to use it :
http://forum.xda-developers.com/showthread.php?t=311403
If it work try to flash with any custums roms.
If you don't have this , you only can flash with officials roms. That's why you can't flash with custums roms
Click to expand...
Click to collapse
Thanks for this however I;ve been directed to that thread before and each time it's pointless. There is no point me attempting to USPL my device when I can't get an activesync connection due to the fact it has no OS bootable.
As for the official Roms...I've tried the ones that have been touted as official for the Orbit but with no effect.
My IPL SPL is currently 1.25.0001/1.25.0.000 but when i attempt to flash with official rom (!) it moves to the same as spikez - ipl 3.04.0001 and spl 3.04.0000
Anyone with any further help - ordered a new Touch HD but I need to get this one up and running
Thanks

have you tried sd card flash
make sure you put the orignal rom on the root of a none sdhc card (1gb or smaller) and is renamed to "Arteimg.nbh"
official wm5 rom
official wm6 rom
Simply put the phone in bootloader with your 'boot' card inserted and follow the instructions.

Spikez.....I've tried that before. It reads from the SD card....goes through the motions, and then provides an error after about 5-10mins saying "SD FAT update failed"
Any ideas...please reply if only to say "no chance mate"
Thanks for any help you can give me.

i still guess yours is more likely to be fixed than mine as mine just goes straight to the rgb screen can you take a picture of what appears on your screen.
Try use an none offical rom and does your artemis ask you to "update sd image press this key to start download"

unfortunately i've left my digi cam at work I can explain rather well though, bear with me:
I reset the device with SD card in and I get a white screen saying "Checking SD Card" - there is then an arrow asking me to hit volume key to flash...I do that.
I get 5 mins of "Reading from SD" at the bottom of the white screen. Following that I get a "verifying certificate" message and then about 10seconds later a "SD FAT update failed!!!" message...it then just sits there until I press a key on the device and then it falls back to bootloader (multi coloured screen)
this MUST be fixable by somebody who isn't a noob like me - any ideas?

either try add these files into root of sd card
Enterbootloader.exe
rapitool.exe
RomUpdateUtility.exe
RUUGetInfo.exe
RUUREsource.dll
RUU_USPL_Signed.nbh, and
"Arteimg.nbh"
or try once in bootloader plug in usb and try using a ruu

files didn't work...just went straight through to bootloader as opposed to reading SD card. As for launching the RUU through windows...didn't work either. Bombed out after 5% with a "FLASH WRITE " error

Wiggz said:
My IPL SPL is currently 1.25.0001/1.25.0.000 but when i attempt to flash with official rom (!) it moves to the same as spikez - ipl 3.04.0001 and spl 3.04.0000
Thanks
Click to expand...
Click to collapse
as your ipl and spl is so high i guess you may have a Brick i cant seem to get my one working either as i earlier stated it is very common that people with this ipl and spl cant seem to get theirs back working.

spikez93 said:
as your ipl and spl is so high i guess you may have a Brick i cant seem to get my one working either as i earlier stated it is very common that people with this ipl and spl cant seem to get theirs back working.
Click to expand...
Click to collapse
True but as can be seen from that post...mine shifts from 1.25 to 3.04 depending on the flash attempt?

my best suggestion to you is stick with it. Try read through this sign up and post here andrew, bill, [email protected] and noney82 very helpful read through see if that post is any use.

How to Flash HardSPL (Using Olipro 1.20) - USB or SD

Upgrade to Hard-SPL Olipro 1.20 - USB or SD Just Added SD Card Method at Bottom of this Post
10 Step Program
Pulled from Website dated: Monday August 06, 2007 by ??? if someone knows, I'll give credit.
Recovered and Updated Monday October 27, 2009 by SuperSport
because the WiKi has vanished
Hard SPL will allow you to flash cooked ROMs without SuperCID’ing your device and also will protect your device from being bricked in a bad flash. If a bad flash occurs it should remain in bootloader, and you can re-flash another ROM.
Caution!!! Flashing Hard-SPL will Probably Hard Reset your device!!!! Backup all data FIRST!!!
Before you proceed, check which SPL is on your device:
*** Enter Tri Color Screen ***
--Unplug your phone from USB - Helps to avoid freezing USB Ports
--Hold down the Power & Camera Buttons
--While still holding them down, press the Reset Button using the Stylus
--Release the Reset Button, but continue to hold the Power/Camera buttons until you see the Tri Color Screen
*** Enter Tri Color Screen ***
If your SPL is 1.30.Olipro, 1.20.Olipro, or 9.99 CP, then you already have Hard-SPL on your device and can skip flashing HardSPL, although, I recommend using Olipro 1.20 to avoid problems.
If you want to continue flashing Olipro HardSPL 1.20:
Press the Reset Button using your Stylus. Wait for your phone to start back into Windows. Plug the USB Cable into your phone and PC. Verify ActiveSync or WMDC is connected properly. Now you can Flash.
1. Download "Olipro HardSPL 1.20.zip" in attachment below
2. Unzip the Files, and Run the Program "Olipro HardSPL 1.20.exe" This is a small AutoFlash file I created using Olipro 1.20
3. Windows Vista and Windows 7 may confirm you want to run the program. Choose YES.
4. Check the check box, click ‘Next’
5. Also Check this check box, click ‘Next’
6. In the next window, click the ‘Update’ button
This will show the version number of the ROM, radio, or in this case bootloader that you are about to flash.
7. After the version number has appeared, click 'Next'
8. In the following window, click ‘Next’, your phone may ask if it's ok to run the program, Tap 'Yes'.
(After you click this, the flash will begin, so do not disconnect your device or do anything on your computer)
9. A Progress bar will appear on your computer screen, and your trinity will display a grey screen with progress bar. Be patient while your device is being updated. This will only take a moment.
10. Once your device is finished updating, if it did not automatically soft reset, Press the Reset Button with the Stylus. Click the ‘Finish’ button to exit the RUU program.
To confirm Hard-SPL is on your device, re-enter Tri Color Screen following directions above. You should see the following:
Hard SPL 1.20.Olipro
TRIN100
IPL-0.50 (your device may show IPL-1.00)
TRIN100 MFG
SPL-1.20.Olipro
CONGRATULATIONS!! You have now installed Olipro's Hard-SPL 1.20 on your device using USB Method!! Press the Reset Button with your Stylus to restart.
**********************************
Alternate SD Card Method
**********************************
For those who would rather use their SD Card for this (Maybe your USB Port is not functioning). For this method, the way I'm describing, your phone must be running a version of Windows Mobile. Can be any Version, 5-7. If your phone does not currently run, flash back the OEM ROM that came with it Originally. You can find some in my signature.
Caution!!! Flashing Hard-SPL may Hard Reset your device!!!! Backup all data FIRST!!!
1. Be sure you have a, Non-SDHC, SD Memory Card.
2. Be sure the card is formatted Fat32 and Without a Label.
3. Download the attached HardSPL SD.zip file and extract it's contents. Copy both files, SSPL-TRIN.exe and TRINIMG.nbh, to the Root of your SD Card.
4. On your phone, use File Explorer to browse to the Root of your SD Card.
5. Tap the SSPL-TRIN.exe file. This should run the file.
6. On some phones, you will see a security message come up. Select 'Yes' to run the program.
7. You should now see a Grey screen with Blue Lettering. It will be asking you to Press power button. Go ahead and press the power button.
8. You will see the update progress for a short moment, it will restart, and update again, then show "Update Complete - UPDATE SUCCESS" If you see this message, it has worked.
9. Press the Reset Button with your Stylus to Restart
10. Delete the two files from your SD Card (TRINIMG.nbh, SSPL_TRIN.exe). To confirm Hard-SPL is on your device, Enter Tri Color Screen following directions above. You should see the following:
Hard SPL 1.20.Olipro
TRIN100
IPL-0.50 (your device may show IPL-1.00)
TRIN100 MFG
SPL-1.20.Olipro
CONGRATULATIONS!! You have now installed Olipro's Hard-SPL 1.20 on your device using SD Method!! Press the Reset Button with your Stylus to restart.
Maybe if this could be Stickied?

Thanks, it's a very nice guide for Trinty users, clean and detailed, I also recommand using Olipro 1.20 and not 1.30 to avoid problems, especially with 6.5 roms the annoying "WLAN ERRROR" sometimes seen in bootloader mode ...
Yes, make this "Sticky"
Brds,
nAr

Thanks narshorn! Someone else posted this a long time ago on a WiKi I believe, and I just recovered what I could of the original web page and then rewrote it to work with my files. The original page was removed from it's server, so I grabbed as much of the cached version of it as I could, thus, I don't know who did the original.
Also, thank you for the confirmation of using Olipro 1.20 and not 1.30. That was my belief, and I've heard others, but I'm glad you confirmed.

noob here, need help on flash HardSPL.
i encounter error when trying to update my hardSPL. when i try to flash when my phone is tri color screen mode, this error pop out.
ERROR [270]:UPDATE ERROR
The image file is corrupted. please check your update utility.
info update:
at last i manage to flash my phone to hardspl 1.20, i boot my d810 in normal mode, establish active connection with window, then the flash carry on without any error. but the phone hard reset
but, i wonder y i cant flash to hardspl in tri color screen ???

update to 1.20 spl Olipro true sd card not USB
hi and Thanks for so nice explanation. there is a way to update spl with sd card? my USB connection is faulty. if s/o know please let me know how.

tzuki1 said:
hi and Thanks for so nice explanation. there is a way to update spl with sd card? my USB connection is faulty. if s/o know please let me know how.
Click to expand...
Click to collapse
Just added SD Method to bottom of post #1. Good Luck!

thongkh said:
noob here, need help on flash HardSPL.
i encounter error when trying to update my hardSPL. when i try to flash when my phone is tri color screen mode, this error pop out.
ERROR [270]:UPDATE ERROR
The image file is corrupted. please check your update utility.
info update:
at last i manage to flash my phone to hardspl 1.20, i boot my d810 in normal mode, establish active connection with window, then the flash carry on without any error. but the phone hard reset
but, i wonder y i cant flash to hardspl in tri color screen ???
Click to expand...
Click to collapse
Because stupid me forgot that if you don't have HardSPL on your phone, then TRI COLOR SCREEN flashing is not possible. Doh! FIXED above.
Thank you for bringing this to my attention. When I physically went through the steps, I forgot I still had HardSPL on my phone from previous.
I just went through the steps AGAIN after removing HardSPL, and verifed it works correctly as listed in Post #1.

thankz for promptly reply
btw, what d diff between HardSPL 1.20 and 1.30?

thongkh said:
thankz for promptly reply
btw, what d diff between HardSPL 1.20 and 1.30?
Click to expand...
Click to collapse
I've seen many reports that 1.30 caused issues. Olipro, 'the guy who made our Trinity's safe for Flashing', stopped updating the thread, but if you read it, you will find many users reporting problems and asking for the thread to be updated to go back to 1.20.
I've been using 1.20 since it was released, and have NEVER had a problem with it. And believe me, I Flash a LOT!!! I'm expecting my poor Trinity to catch fire any day now.

Oh... Thx for the tutor...that what i need now...

Good job someone remembered howto
Thanks for the reminder - managed to forget how to enter tri-colour screen in the three months since I last reflashed.

I need help here
I have tried each of the methods.
though your explanation and step by step instructins are very clear, istill can't seem to get Olipro's HSPL on my phone. in the case of using active sync, after it enters the tri color screen nothing happens again and the i get an error message (ERROR 260).
When i tried using the SD method, when i tapped the SSPL_TRIN file, it goes stright to the tri color screen ths is the information i have there
TRIN100
IPL-SSPL by Des
TRIN100
SPL-1.07.ds
and for this reason i can seem to flash any rom with success each time it only gets to the tri colou screen and i get the ERROR 260 message.
Anyone with any idea on how i can fix this.
thanks in advance

redoxy said:
I need help here
I have tried each of the methods.
though your explanation and step by step instructins are very clear, istill can't seem to get Olipro's HSPL on my phone. in the case of using active sync, after it enters the tri color screen nothing happens again and the i get an error message (ERROR 260).
When i tried using the SD method, when i tapped the SSPL_TRIN file, it goes stright to the tri color screen ths is the information i have there
TRIN100
IPL-SSPL by Des
TRIN100
SPL-1.07.ds
and for this reason i can seem to flash any rom with success each time it only gets to the tri colou screen and i get the ERROR 260 message.
Anyone with any idea on how i can fix this.
thanks in advance
Click to expand...
Click to collapse
Did you copy the TRINIMG.nbh file to your SD Card also? Was your SD Card formatted FAT32 and No Label?
Using the SD Method, you do not need to be connected to your Computer. Copy both files to SD and do all work from phone.
Let me know if that works or not.

Remove the HARDSPL...
Hi,
How can I remove the HARDSPL from my Trinity and go back to the original?! Thanks!

sergiopedro said:
Hi,
How can I remove the HARDSPL from my Trinity and go back to the original?! Thanks!
Click to expand...
Click to collapse
Only do this if you do not plan to flash any more Custom ROMs, and would like to stick with the OEM ROM (You may Brick your Phone if you flash from the Stock SPL):
Download the "HardSPL SD.zip " file from the first post.
Extract the files
Copy ONLY the "SSPL_TRIN.exe" file to your SD Card.
Run the "SSPL_TRIN.exe" file from your SD Card (This puts your phone into a special mode that will allow the HardSPL to be overwritten)
Now, your phone should be in bootloader mode with:
TRIN100
IPL_SSPL by Des
TRIN100
SPL_1.07.ds
At this point, you can flash your OEM ROM that includes the Original SPL and IPL.
I use this one: http://www.mediafire.com/?v5yjt1zvgjm

Hi all
I have tried to flash with usb but i'm having a problem
i'm using active sync and after i click 'execute' at the mobile screen it enters the tri color screen and it disconnects the usb port. I get an error message (ERROR 246) that says the device is not responding.
I've tryed several times and it has the same behavior...
The tricolor screen shows this message:
TRIN100
IPL-SSPL by Des
TRIN100
SPL-1.07.ds
i havent try the sd method because i dont have a sd card right now...
Thank you

rcpamr said:
Hi all
I have tried to flash with usb but i'm having a problem
i'm using active sync and after i click 'execute' at the mobile screen it enters the tri color screen and it disconnects the usb port. I get an error message (ERROR 246) that says the device is not responding.
I've tryed several times and it has the same behavior...
The tricolor screen shows this message:
TRIN100
IPL-SSPL by Des
TRIN100
SPL-1.07.ds
i havent try the sd method because i dont have a sd card right now...
Thank you
Click to expand...
Click to collapse
Your mobile screen is showing the correct information, with the exception of USB not showing. As soon as you get to the Tri Color Screen, try removing then reconnecting the USB connection and see if that makes any difference.
Also, when the Tri Color Screen comes up, does your computer ask to install a driver? If it does, be sure to allow that.

SuperSport said:
Your mobile screen is showing the correct information, with the exception of USB not showing. As soon as you get to the Tri Color Screen, try removing then reconnecting the USB connection and see if that makes any difference.
Also, when the Tri Color Screen comes up, does your computer ask to install a driver? If it does, be sure to allow that.
Click to expand...
Click to collapse
Well i just trying all steps again and it worked just fine...go figure!
Thank u anyway

rcpamr said:
Well i just trying all steps again and it worked just fine...go figure!
Thank u anyway
Click to expand...
Click to collapse
Glad to hear you are going. Now you are safe to flash custom ROMs.
Also, remember that each time you flash back to the OEM ROM for any reason, it replaces the HardSPL with the stock one. You will then need to flash the HardSPL back again. At least this is the case for the OEM that I use.

SuperSport said:
Glad to hear you are going. Now you are safe to flash custom ROMs.
Also, remember that each time you flash back to the OEM ROM for any reason, it replaces the HardSPL with the stock one. You will then need to flash the HardSPL back again. At least this is the case for the OEM that I use.
Click to expand...
Click to collapse
ok. thank u so much!