Develop Bugs

P3300 Boot Problem

Please Help
I Have A P3300 And After Changing Rom (had Greek Rom) And I Put The Pdaviet The Pda Can Not Boot.
I Tried With Hard Reset To Make It Boot Again But Even If I Tried Several Times The Result Is Always The Same:
Ipl 3.04.0001
Spl 3.04.000.
Gsm 02.93.90
Os 4.0.0.0
And The Booting Stops There
Does Anybody Can Help?

LINANTONIS said:
Please Help
I Have A P3300 And After Changing Rom (had Greek Rom) And I Put The Pdaviet The Pda Can Not Boot.
I Tried With Hard Reset To Make It Boot Again But Even If I Tried Several Times The Result Is Always The Same:
Ipl 3.04.0001
Spl 3.04.000.
Gsm 02.93.90
Os 4.0.0.0
And The Booting Stops There
Does Anybody Can Help?
Click to expand...
Click to collapse
can you enter the boatloader?

Boot Problem
Unfortunately I Can Not Syncronize It So I Can Not Put The Boatloader

you can go into the bootloader by pressing the voice speed dial button and soft reset your device.
then you will get a 3 collor screen (red,green and blue). if you are in the screen connect your usb cable and you will have a connection so you can update the rom.
first use USPL and after that run the rom update utility

Thank You For Your Help
But I Did What You Told Me I Connected And I Start Running The Uspl.
Unfortunately The Spl Can Not Finish And Stuck Always In 50.
From 30 To 50 The Message Is :cant Spawn Cmd.exe.:no Such File In Directory C:

HardSPL + MTTY, an almost bricked HTC Diamond!

I really need some help!
I was following the the post The DEFINITIVE MTTY Thread!! REVISED 02-11-09 and I made a mistake as follows;
blanktruth said:
Ok, first of all I did not think that it was this dangerous to use MTTY!.
I followed everything and came to these lines
---------------------
Cmd>task 8
Cmd>
---------------------
But after Cmd>task 8 my device restarted immediately before the second line Cmd> appears and I panicked and disconnected my device and pushed the wrong buttons while "Touch Diamond" logo was on the screen.
Now, nothing happens. I can not start from the beginning because I can not start the bootloader by pushing Vol Down and the small red reset button...
Is there anything else left for me to try? Or should I throw my HTC to garbage?
Click to expand...
Click to collapse
Now, I do not know how, but I brought my HTC to bootloader mode and now I can see it via MTTY. But I mistakenly formatted the Internal Storage while I was trying to bring my HTC to bootloader.
Is there any way to upload the DIAMIMG.nbh file to Internal Storage? Or should I follow a different way to save my HTC Diamond?

i have the same probnlem!! with my diam300
my bootloader show not Diam300 64m but only 64M on the first position in 3color mode... plz help

Connect the Diamond and run the customruu.exe from your desktop, this should work.

how to connect if i used mtty... its clear everything what i have on device storage and in bootloader canot start stock or developed rom...
if i want start hard spl its say invalid model it....

blanktruth said:
I really need some help!
I was following the the post The DEFINITIVE MTTY Thread!! REVISED 02-11-09 and I made a mistake as follows;
Now, I do not know how, but I brought my HTC to bootloader mode and now I can see it via MTTY. But I mistakenly formatted the Internal Storage while I was trying to bring my HTC to bootloader.
Is there any way to upload the DIAMIMG.nbh file to Internal Storage? Or should I follow a different way to save my HTC Diamond?
Click to expand...
Click to collapse
The only thing to do now is to flash back a stock ROM or use a custom ROM with the RUU.

Solved!...
Dom1n8tr1x said:
First of, your device is supposed to soft-reset after the "task 8" command and you should have been holding down the "Volume Down" and "Back Buttons" to begin flashing your new ROM. The whole idea of using MTTY is to format your Main Storage and flash a new ROM. Therefor you should have loaded the ROM that you wanted to flash onto your Internal Storage.
Click to expand...
Click to collapse
Thank you for your reply.
Actually I had uploaded the ROM to my internal storage, but during trying to bring my phone to bootloader mode, I formatted the internal storage...
Anyway, what I did now is, first I opened the USB Connection feature from ActiveSync, and then used CustomRUU.exe to Flash the ROM...
Everything is solved now...
Thank you very much all...

ilijan said:
how to connect if i used mtty... its clear everything what i have on device storage and in bootloader canot start stock or developed rom...
if i want start hard spl its say invalid model it....[/QUOT
bootloader is all you need to revive the phone
connect it to usb in bootloader mode and just install an oficial diamond rom from an windows xp pc.
it's easy
Click to expand...
Click to collapse

plz write here step by step guide how you solved

How it was solved...
ilijan said:
plz write here step by step guide how you solved
Click to expand...
Click to collapse
Actually the most crucial part was to bringing phone to boot loader mode. And I think I managed that by pushing the Volume Down and Back (the arrow pointing left) buttons immediately after restarting my phone. And I had to do this after taking out the battery and putting it back after 5 sec.
When I pushed these buttons at the start up the phone tried to install the ROM from my internal storage, but as I explained I had deleted it by mistake. Therefore it could not find the ROM. I disconnected my phone from my PC and the screen started to say something like Retrying USB connection or waiting for USB connection, something like that.
I restarted my PC in Digitally Signed feature disabled by pressing F8 during start-up. Reconnected my phone to PC (the screen of the phone was still blinking as waiting or retrying usb connection). And voila the phone screen changed to boot loader mode...
The rest was easy. I opened the USB connection feature from ActiveSync and used CustomRUU.exe with a ROM to flash my phone...
That is all...

1. plug phone in to computer in bootloader
2. run customruu or stock from rom update on computer
3. wait for rom to flash to device
4.???
5.profit

but my booloader dont show model ID: DIAM300 64M what i had befor
and show me only: 64M
and any flash error with invalid model id, i canot flash, rom, stock rom, or hardspl...
understand me.. im not totaly noob... i used mtty X times... but now have this probles

can somebody help me?
my diamond dont have model id...
before i had in bootloader mode DIAM300 64M model id, but now i havent got... its show only 64M,
every rom flash stopped at 1% cose model id error,
every hard spl falsh finished 100% but after flash when device restart write model id error...
i cant do anithing... can somebody help me?

For everyone facing problems after flashing his/her device, take a look at the link in my sig.
There you can find a guide to restore your diamond.

you dont understand me..
i canto flash any rom any hard spl becous my diamond dont have device ID...
in bootloader dont show DIAM300 64M but only 64M
after all flash say error mobile ID...
i try mtty, hard reseted, soft... and nothing
after start its show me only first stock screan, the red text on the right bottom sight dont start: 1.17.25.14
2.100000
geny d2x
its maybe wrong but i forgot what waz here...
how can change device model ID? form 64M back to my stock DIAM300 64M?

Try another version of Hard-SPL, some people report that 1.40 not fully works.
I suggest you try 1.94 Olinex.

my diamond is death... if somebody know how can heal it... plz write me...
my device ID is missing... so i cant flash any rom, any hard spl, any radio...

try this? http://forum.xda-developers.com/showthread.php?t=409425&highlight=invalid+model+id

im not sure but i dont think one can brick his/her phone after hard spl, thats the reason of hard spl in the first place that u dont brick it. boot loader is always present

Guide
if you are using Windows XP try the following steps:
Connect your device to your PC
In Active Sync > connection settings > check Allow USB connections (which you have un-checked while doing MTTY)
Find a ROM with CustomRUU.exe / diamond wrapper
Now enter into bootloader mode(forget about the device ID)
Go to customRUU.exe and run it
Follow the ROM installation steps
This will help you installing your new ROM.
I had a similar problem and i resolved it by follwoing the above steps.

Guide
if you are using Windows XP try the following steps:
Connect your device to your PCIn Active Sync > connection settings > check
Allow USB connections (which you have un-checked while doing MTTY)
Find a ROM with CustomRUU.exe / diamond wrapper
Now enter into bootloader mode(forget about the device ID)
Go to customRUU.exe and run it
Follow the ROM installation steps
This will help you installing your new ROM.
I had a similar problem and i resolved it by follwoing the above steps.

p3300 freezing

Hi people
my p3300 keeps freezing after a few seconds on booting, it gets stuck on the boot screen where it displays your spl and gsm versions, also when i put it into bootloader it freezes if im quick enough to attach the usb cable the screen fades away to nothing.
does anyone have an idea i have even tried hard resetting but it says "format failed"
here is my setup
ipl - 1.14.0001
spl - 1.14.0000
gsm - 02.67.90
os - 1.14.0.0
it was running wm2005
my computer is win7 ultimate 32bit
any help will be appreciated

no help at all !
please guys

I have the exact same problem:
ipl - 1.14.0001
spl - 1.14.0000
gsm - 02.67.90
os - 1.14.0.0
it was running wm2005
only exception is that mine agrees to hardreset ... "Format is complete"
I have replaced the battery with a new and charged it before trying to boot.
I can enter the bootloader (this 3 colored screen) but I'm not really sure on what is safe to do from there.
I would prefer to try and put a original ROM from htc.com on the device but they have removed p3300 rom's from the download page
I have not used the device for half a year or so... is it a y2k10 problem ?!

looks like I found the solution.
I managed to put a old rom onto the p3300 from my SDCard described here
wiki.xda-developers.com/index.php?pagename=Artemis_SD_Card_Flashing

[Q] Help please. P3300 stuck in HTC screen!!

When turned on it shows a HTC screen with :
IPL 1.12.0001
SPL 1.12.0000
GSM 02.67.90
OS 1.12.0.0
I can get into bootloader mode but doesn´t know what to do then. Tried a hard reset but ends up with the same start-up screen.
I downloaded mtty because I saw in another post I might need that. Think I also need a Danish Rom, but have no idea how to get one.
Hope someone can help me?

...
if you gona use mtty.. (might not be needed in your case)
when it opens TYPE (no copy and paste, it wont work)
Cmd>password BsaD5SeoA
Cmd>ruurun 0
Cmd>ResetDevice
anyway..
you cant go no further than the start-up screne because I GUESS you tried flashing with no USPL..
click 1.11.cmon in my signature to download..
uspl 1.11.cmon will basicly take the security off the device so an unofficial/cooked rom can be flashed no matter what the rom size is.. instructions inside uspl1.11.cmon folder..
youl need your original rom though which can be found here
so.. to do list:
*find original rom - i think its the English or French rom..
*flash original rom - run ruu or use mtty
*do uspl 1.11.cmon - DONT SOFTRESET when instructions tells you to!
*flash new unofficial/cooked rom
DONE
any questions or if you get stuck, just private message me and ill help the best i can..
Rn

Thanks. I´ll try it out this weekend.

[Q] Bricked Artemis - can enter bootloader

Hello,
a friend of mine probably bricked his Artemis. He tried to flash, but did not HSPL first. Now the device can enter only bootloader. I tried many USPLs, MTTY, micro SD but nothing worked.
The version of SPL is 1.14, active sync does not go green after connecting, but if I try to flash, it is recognized and returns Error 300. I guess I need the original ROM, but it was in czech and I cannot find it anywhere.
Any ideas are very welcome.
Thanks in advance.

parizek said:
Hello,
a friend of mine probably bricked his Artemis. He tried to flash, but did not HSPL first. Now the device can enter only bootloader. I tried many USPLs, MTTY, micro SD but nothing worked.
The version of SPL is 1.14, active sync does not go green after connecting, but if I try to flash, it is recognized and returns Error 260. I guess I need the original ROM, but it was in czech and I cannot find it anywhere.
Any ideas are very welcome.
Thanks in advance.
Click to expand...
Click to collapse
for SPL Artemis you can try this and to l his official ROM you can look at -> http://www.shipped-roms.com/index.php?category=windows mobile&model = Artemis​ but first try to him that your friend's device hardreset !! like this way :To perform a hard reset
Press and hold the Left SOFT KEY and the Right SOFT KEY, and at the same time, use the stylus to press the RESET button at the lower left side of your device.
Release the stylus, but continue pressing the two soft key buttons. Release them only when you see the following message on your device screen: “Press Send to restore manufacturer default, or press other keys to cancel.“
Press on your device. Warning! Your device will be set back to factory default settings. Please ensure any additional installed programs and/or user data have been backed up before a hard reset is performed.

thanks for ideas. HR cannot be made - returns error like "cannot format partition".
On the shipped ROMs site I cannot download anything - it only says something about redirection on ppc geeks
Here I attach the screen, what I get after trying to flash..

...
only the original rom will bring your device back to life.
whats your red numbers and letters at device start-up?

I can get only to bootloader, so the IPL : 1.14.0001 and SPL 1.14.0000 , that's all I can get

hmm, after a communication with official HTC servise in Czech Republic I got the number of original ROM and successfully downloaded it.
But still the same issue. Is it possible, that Bootloader is corrupted ? The guy told me that it is the only possible cause, if this ROM does not work

...
Try this original rom..
The bootloader of this rom matches yours..
(1.14.0000)
1. Put device into bootloader
2. Connect device to PC
3. Run the RUU
4(a). If this does not work, then you are stuck in the mud..
4(b). If that original rom does work, then click here for USPL 1.11.CMON
Good luck!
Rn

Hi,
thanks man for all the ideas. Unfortunately the ROM you are hyperlinkinkg I have already tried with no success. I have given it maximum, now I am giving it up.
Thanks for your patient help.
p

ME to in same problem plz help IPL 3.04.0001 and SPL 3.04.0000