Recently tried upgrading my SPV M3100 from WM5 to black WM6. Everything was going fine and I had installed the following
SPL (Bootloader) version 2.10.Olipro (HardSPL v7)
Radio version 1.43.00.00 (optional)
Was updating to ROM version: Windows Mobile 6 LVSW 160607 when USB cable was disconnected before installation ands I am now left with WM6 screen only
Can anyone help?
If you stuck in the wm6 boot screen and have flashed HardSPL 2.10 already you can just enter the bootloader and reflash your ROM again. Why do you use nearly 6 months old ROM (LVSW)?
Did you try to reflash the ROM?
Just switch to the bootloader and run the update again.
If the updater is complaining about "Not able to do so" you might need another ROM, but that method worked to or three times for me.
Cheers,
Jago
tried raflashing but activesync won't pick up phone
you do not need active sync to pick it up. Just enter the bootloader and run RUU.
how do you reflash without activesync?
Read this:
http://wiki.xda-developers.com/index.php?pagename=Hermes_Unbrick
richard_g_johnston said:
how do you reflash without activesync?
Click to expand...
Click to collapse
Simply - flashing process itself is not done by the Active sync (its icon is grey when flashing). I have tried to flash a ROM this way and it works. You just have to input correct values to the RUU yourself. Bootloader is the tri color screen. You can access it by holding power and ok button while using the stylus to soft reset the device. Hermes will pick up the usb connection.
Please read the WIKI and flash an original WM6/WM5 rom before attempting to flash a cooked rom.. then make sure you know what you are doing before flashing the cooked.
tried both
http://wiki.xda-developers.com/index...Hermes_Unbrick
http://forum.xda-developers.com/showthread.php?t=286755
still no joy
my device
IPL-1.04
SPL-2.10.0lipro
how do u run RUU in bootloader mode?
richard_g_johnston said:
tried both
http://wiki.xda-developers.com/index...Hermes_Unbrick
http://forum.xda-developers.com/showthread.php?t=286755
still no joy
my device
IPL-1.04
SPL-2.10.0lipro
how do u run RUU in bootloader mode?
Click to expand...
Click to collapse
Put your device into bootloader mode.
Connect it via USB to your PC.
Run the RUU on your PC (like if you had Active sync working).
Flash the ROM.
(should work with all cooked ROMs)
Update: I tried it now with the Schaps 4.20 - it is working.
When you run ruu it should create ROMUpgradeUt.exe if it says it fails to find the device just run this. I usually take a copy before clicking to close the error box.
where do u locate RUU.exe
sorry I'm not an expert in this
RUUWrapper.exe should be in the folder with the image you are flashing. Sorry if I confused you saying ruu.
When you download the cooked rom it comes in rar or zip containing 2 files - one with extension .NBH and the second one is RUUWrapper.exe (resource upgrade unit), unpack them to one folder and run RUU.exe Be sure to flash only ROM for your device otherwise you will kill it for good.
tried running RUU but get error 260, i.e. cannot pick up phone on USB
See post 12
yeah, tried running ROMUpgradeUt.exe, but still no joy
markafreeman said:
See post 12
Click to expand...
Click to collapse
If this does not work for you - then you can use flashing from the SD card (no USB needed for this kind of flashing) . But try what markafreeman suggests first.
Lets try some troubleshooting:
Whne you connect your device in the bootloader (red green blue screen) to your pc what does it say?
In the white part of the screen on your device it should say USB - then it will work.
If not you can still try flashing the ROM from the SD card - you will need a card reader though for this kind of flashing.
Related
I have download two nb rom files and make nbh file with NBHgen and sample.txt (only OS and extended rom). After that I run modifided ruu updater with autodetecting SPL and start the update. I have to mention that my hermes was CID unlocked and I have flashed hundred of devices before. After about 23% updater stoped with an error message and want to start recovery mode... So I restarted my hermes but it not came up. Few seconds later my computer hangs on with blue screen message. Hermes never came up, even to bootloader. KITL mode also don't work. Charging too. Computer don't detect anything :-( Anyone have any suggestions? What could happend? I have not updateing SPL so why it won't start to bootloader?
ell82 said:
I have download two nb rom files and make nbh file with NBHgen and sample.txt (only OS and extended rom). After that I run modifided ruu updater with autodetecting SPL and start the update. I have to mention that my hermes was CID unlocked and I have flashed hundred of devices before. After about 23% updater stoped with an error message and want to start recovery mode... So I restarted my hermes but it not came up. Few seconds later my computer hangs on with blue screen message. Hermes never came up, even to bootloader. KITL mode also don't work. Charging too. Computer don't detect anything :-( Anyone have any suggestions? What could happend? I have not updateing SPL so why it won't start to bootloader?
Click to expand...
Click to collapse
did you have hardSPL when you flashed it?
ell82 said:
I have download two nb rom files and make nbh file with NBHgen and sample.txt (only OS and extended rom). After that I run modifided ruu updater with autodetecting SPL and start the update. I have to mention that my hermes was CID unlocked and I have flashed hundred of devices before. After about 23% updater stoped with an error message and want to start recovery mode... So I restarted my hermes but it not came up. Few seconds later my computer hangs on with blue screen message. Hermes never came up, even to bootloader. KITL mode also don't work. Charging too. Computer don't detect anything :-( Anyone have any suggestions? What could happend? I have not updateing SPL so why it won't start to bootloader?
Click to expand...
Click to collapse
Don't worry about it, if you have hardspl you can flash it again
okk said:
Don't worry about it, if you have hardspl you can flash it again
Click to expand...
Click to collapse
How do I can if it's not even start to bootloader?? I'm almost confident it was hardspl.
ell82 said:
How do I can if it's not even start to bootloader?? I'm almost confident it was hardspl.
Click to expand...
Click to collapse
You seem to have a dead battery, you need to charge it before you can flash your device again.
For clarification, if your battery is in fact dead, you won't be able to charge it with your own phone in it's current state (failed flash). You'll have to put the battery in another phone to charge or borrow someone else's battery.
shafez said:
You seem to have a dead battery, you need to charge it before you can flash your device again.
Click to expand...
Click to collapse
ell82 said:
I have download two nb rom files and make nbh file with NBHgen and sample.txt (only OS and extended rom). After that I run modifided ruu updater with autodetecting SPL and start the update. I have to mention that my hermes was CID unlocked and I have flashed hundred of devices before. After about 23% updater stoped with an error message and want to start recovery mode... So I restarted my hermes but it not came up. Few seconds later my computer hangs on with blue screen message. Hermes never came up, even to bootloader. KITL mode also don't work. Charging too. Computer don't detect anything :-( Anyone have any suggestions? What could happend? I have not updateing SPL so why it won't start to bootloader?
Click to expand...
Click to collapse
First, it souds like there's something wrong with your computer if you get a blue screen. You might wanna try rebooting your computer first. Use the AC wall adapter to charge your phone if you can't charge it on the computer. If you are able to charge the phone with the AC walll adapter, see if you can go into SPL or KITL. If you were able to get into the bootload or KITL, you will be fine.
The battery was charged before update to 100% so for sure it's not empty... :-(
Tell more about the PC
Most likely the blue screen is related to the USB driver. There should be a hex code displayed. What was that?
Also, please share OS version, and I don't want to assume ActiveSync version either.
We've got to fix the PC first. Have you tried Pof's "How to unbrick your Hermes" steps?
Try removing the battery for a while (as long as you can stand to), like at least 10 minutes, then put it back in.
Let us know just a bit more about your configuration.
ell82 said:
The battery was charged before update to 100% so for sure it's not empty... :-(
Click to expand...
Click to collapse
OS ver is Windows 2003 Enterprise R2 trial version, ActiveSync of course 4,5.
Pof's "How to unbrick your Hermes" steps will not work becouse my hermes is dead and even don't wont boot to bootloader or KITL... Removing battery for few hours do nothing. I'm not at home now, so I don't try to bring it back to life last few hours but I will soon.
ell82 said:
OS ver is Windows 2003 Enterprise R2 trial version, ActiveSync of course 4,5.
Pof's "How to unbrick your Hermes" steps will not work becouse my hermes is dead and even don't wont boot to bootloader or KITL... Removing battery for few hours do nothing. I'm not at home now, so I don't try to bring it back to life last few hours but I will soon.
Click to expand...
Click to collapse
Hmm...if you can't even get to the bootloader or KITL..your phone is basically dead.
I have written in first post that it's not boot to bootloader... Anyway, how is it possible to brick bootloader while I was flashing only OS and extended rom?
sample.txt
please show your sample.txt.
ell82 said:
I have written in first post that it's not boot to bootloader... Anyway, how is it possible to brick bootloader while I was flashing only OS and extended rom?
Click to expand...
Click to collapse
It's possible when you use the custom RUU Updater and you choose the wrong option, it will start to flash your bootloader first then the OS.
Does it includes IPL flashing ?
See this thread by Olipro
http://forum.xda-developers.com/showthread.php?p=1226412#post1226412
ell82 said:
I have download two nb rom files and make nbh file with NBHgen and sample.txt (only OS and extended rom). After that I run modifided ruu updater with autodetecting SPL and start the update. I have to mention that my hermes was CID unlocked and I have flashed hundred of devices before. After about 23% updater stoped with an error message and want to start recovery mode... So I restarted my hermes but it not came up. Few seconds later my computer hangs on with blue screen message. Hermes never came up, even to bootloader. KITL mode also don't work. Charging too. Computer don't detect anything :-( Anyone have any suggestions? What could happend? I have not updateing SPL so why it won't start to bootloader?
Click to expand...
Click to collapse
I forgot to mention that there's no need to include the extended rom. You can just ust the OS only and those extract CABs will run automatically when your first initialize your device. All the CABs in the extended rom is also in the \windows directory and there's a preconfig.txt file to specifiy which CAB to run. There's also a chance that you specify the wrong range in your sample.txt file which will caused the rom written in a different address and bricked your device.
sunlip said:
Does it includes IPL flashing ?
See this thread by Olipro
http://forum.xda-developers.com/showthread.php?p=1226412#post1226412
Click to expand...
Click to collapse
OS only don't have IPL in there unless you are doing a full rom upgrade.
My sample.txt looks like this:
HERM100
SuperCID
2.05.255.1
WWE
100,00_IPL.nb
200,01_SPL.nb
600,02_MainSplash.nb
601,03_SubSplash.nb
700,04_ExtROM.nb
300,05_GSM.nb
400,06_OS.nb
Click to expand...
Click to collapse
and my RUU updater marked this options before flash (see atatchment).
You created a NBH with a header containing IPL, SPL, splashes, and radio... and you only put OS and ExtROM in the NBH. You overwrite IPL & SPL with EMPTY data. Device is dead. Your "sample.txt" should have looked like this:
Code:
HERM100
SuperCID
2.05.255.1
WWE
700,04_ExtROM.nb
400,06_OS.nb
pof said:
You created a NBH with a header containing IPL, SPL, splashes, and radio... and you only put OS and ExtROM in the NBH. You overwrite IPL & SPL with EMPTY data. Device is dead. Your "sample.txt" should have looked like this:
Code:
HERM100
SuperCID
2.05.255.1
WWE
700,04_ExtROM.nb
400,06_OS.nb
Click to expand...
Click to collapse
If I may be so bold.. Your machine is a complete write-off. It is dead forever. Get it replaced..
As newbie on this, anyone please guide me step by step to upgrade my P3300 rom with nbh file. My device is unlock already with current ROM 5.2.1908 (build 18125.0.4.2).
The procedure is given in almost every thread. It's simple really. Is your SPL version anything other than 1.11.0000 or 1.11.cmon? If yes then your phone is not unlocked. Unlock your phone by running USPL from here or the updated USPL from here.
Check if the USPL has worked by checking your SPL number. During phone booting at the white HTC screen your SPL should show either 1.11.0000 ir 1.11.cmon.
If it does you are free to flash any ROM. Get the ROM of your choice, put your phone into bootloader mode by pressing the voice record, power key and reset button simultaenously for about 5 seconds till you see a three colored screen. Attach it with USB and flash the rom using RUU.
thanks randythered for ur reply. I did w/o problem on USPL but how to use the nbh extention? where that nbh file I shall put in? pc or devise or on specific folder? I got the three colors already, then what next? pl. enlighted
stacknickel said:
thanks randythered for ur reply. I did w/o problem on USPL but how to use the nbh extention? where that nbh file I shall put in? pc or devise or on specific folder? I got the three colors already, then what next? pl. enlighted
Click to expand...
Click to collapse
do u have only .nbh file or along with .nbh file any other files are there ?
generally along with the .nbh file there are other files like romupdateutuility.exe etc.,
download those files also and save those files into your PC.
after unlocking your device then staup the device with bootloader mode (three color screen)
connect the Device with the PC by USB cable.
in the device display u will a word USB (left bottom corner)
run the Romupdateutility from the PC...
the process will guide u next steps ...
after the completion u will have new OS
Last I would recommend tht u also upgrade you Radio ROM (this is responsible for all the communication functions of ur phone i.e. calls, GPS, WiFi etc) which will enhance the communication capabilities.
Radio ROMs Link : http://wiki.xda-developers.com/index..._RadioUpgrades.
Note : before flashing any ROM or upgrading the RADIO kindly CID unlock your device or you will end up the with bricked device .
You can download my ROMs, they come with the full package
trying upload but without success...
after remember operation will take 10 minutes
it displays
"Error [270]: UPDATE ERROR
Image file is corrupted. Please check your Update Utility"
Did I miss something here? Pl. help
stacknickel said:
trying upload but without success...
after remember operation will take 10 minutes
it displays
"Error [270]: UPDATE ERROR
Image file is corrupted. Please check your Update Utility"
Did I miss something here? Pl. help
Click to expand...
Click to collapse
your device not properly CID unlocked...
unlock the device properly with USPL...
stacknickel said:
trying upload but without success...
after remember operation will take 10 minutes
it displays
"Error [270]: UPDATE ERROR
Image file is corrupted. Please check your Update Utility"
Did I miss something here? Pl. help
Click to expand...
Click to collapse
As sixthsigma said, did you check if the phone is correctly unlocked? Is the SPL showing 1.11.0000 or 1.11.cmon?
Secondly, what OS are you flashing on? XP, Vista or Windows 7?
Hi Randythered, IPL 1.25.0001 and SPL 1.27.0000
I am using your ROM RtR Manila v1.0
using XP
Well, firstly thank you for wanting to try out my ROM
Secondly, you haven't unlocked your phone properly yet. The SPL must be 1.11.0000 or1.11.cmon, depending on which USPL you use.
strange... hv tried several time but w/o luck...
now I notice that it cut out after '70' and jump into 100 with disconnecting
any choices of other USPL instead of the one attached here?
Did you flash the old USPL or the new one which is nosize? It is preferable to install the old one first. And then go for the cmon nosize USPL if need be.
From a noob to a noob
Hi, heres the procedure for upgrading your rom put as noob friendly as i can put it.
WHAT YOU NEED
1. HTC Artemis p3300
2. computer running Windows XP with activesync installed
3. Usb cable to connect to computer
4. The new rom that you want to flash
5. And USPL which can be downloaded at this page http://forum.xda-developers.com/showthread.php?t=311403
NB: For most of the newer roms you will probably need the updated nosize version of uspl http://forum.xda-developers.com/showthread.php?t=521406
PREPARATION
NB: Anything you need to backup or keep from your device do it now.
NB: in some cases you may have to hard reset your device before it will take the flash
1. Extract Uspl to your desktop
2. Extract the rom you downloaded to your desktop
3. Remove your sim chip and memory card from your device
4. Reset your device and sync with windows xp
UPDATING
1. In the USPL folder run the program called "start_uspl" and let it do its thing in the dos window,in
my case it goes to 70 and then jumps to 100,if you have been watching your device screen you will
see the linux penguin for a few seconds and it will change to a white screen.
A window will popup on your computer, do as it requests, when finished it will reset your device.
Sync your device with your computer again.
2. In your downloaded rom folder you should find a file called "ROMUpdateUtility.exe" or "Ruu.exe", run
it and a window will popup, do as it requests.
Your device screen will go tri-color(red,green,blue) and the rom update will begin, wait till it
finishes and thats it.
thanks soloman1 and others
finally I got it with removing the sim card and memory card prior to upgrading
stacknickel said:
thanks soloman1 and others
finally I got it with removing the sim card and memory card prior to upgrading
Click to expand...
Click to collapse
same ting got me with my first rom thats why i thought to put it in, happy flashing (not in the naked way )
Lol I can't belive I forgot to tell you that!
It's ok. Thanks to u too randythered.
Do you have dedicate Manila in cab file?
Thank you, here you go!
sixthsigma said:
your device not properly CID unlocked...
unlock the device properly with USPL...
Click to expand...
Click to collapse
Sixthsigma...you said - "unlock the device properly with USPL..." - how do I do that?
I got the same error as mentioned when trying to flash using the numb3rs ROM:
http://thewingster.com/numb3rs.aspx
I ran the herald-uspl.exe file. and ended up with teh above error. My TMo Wing has the original ROM on it and the phone itself is probably unlocked. Ive had it for a year now. Do I need to call TMo to unlock or is there some app I can run to do this myself?
appreciate any help!
nevermind, it worked ok on the second attempt!
First of all, hi, i was reading a lot from this forum, and i must say, im impressed. Nice job!
Anyhoo, im running WM 6.1 (Lite) (http://forum.xda-developers.com/showthread.php?t=364031) on my HTC TyTn.
Now id like to flash it into, i dunno, the full version, or 6.5, or something else, but it wont.
I connect it through active sync(on my desktop pc), and i run 'Force Using Safe SSPL', i get the error : ERROR 246. The Update Utility cannot get response from your PDA Phone. Please check that your USB cradle/cable is connected properly between the PC and your PDA Phone. And also check your PDA Phone.
Click 'Exit' to quit.
I tried to run SPL-2.02/2.10/2.30 and then it goes into bootloader, and at 1% it says 'file corrupted'.
I tried those things on my laptop, too, but still the same problems.
Can anyone help me?
Rgrds
Install NetFrameworks from v1 to v3.5 make first your device is runing a functional rom.... or your rom... then perform the Hardspl v7 by olipro hardspl 2.10 and then try to upgrade some other... the fact here is.... how could you have 6.1 and now you are trying to make hardspl... oh bTW dont use SSPL please you gonna damage your device if it is not ready damaged.
Do i install NetFrameworks on HTC or on my PC?
Why not use SSPL? Which option should i use?
Do i install NetFrameworks on HTC or on my PC?
Why not use SSPL? Which option should i use?
hi,
when i try to perform the Hardspl v7 by olipro hardspl 2.10 i the following error:
Error 206 update problem
http://img97.imageshack.us/img97/107/48319879.png
please help me
nvr, worked it out.
Try this,
1. Make sure you have HSPL 2.10 or New Bootloader
2. Put Your device into bootloader mode (Until there a "SERIAL" in the bottom of ur device), connect it to PC (Now "SERIAL" change to "USB")
3. Run 838Pro_SEA_ENG_WM6_Upgrade_20070712 (official ROM or U can RUN other official ROM can be found on www.htc.com ), don't click "AUTODETECT",
4. Checklist the option button of SPL-2.02/2.10/2.30 New Bootloader and Is it Hard-SPL?, after that just click next2 until flashing started
5. If it didnt work repeat step 1-3 and checklist the option button " Force Using Safe SSPL " then follow all flashing step
6. Run AT&T Strip, link: http://www.4shared.com/file/61372397/e2bf76c0/official_ATT_WM6_striped.html
7. Flash WM6.5 ROM you want
Hope its usefull cause I use this when my hermes couldnt load and every flashing it's stuck on 1%
Good Luck
ksemeks said:
nvr, worked it out.
Click to expand...
Click to collapse
I'm having similar problems too, Please kindly share how you worked it out.
Upgrade to Hard-SPL Olipro 1.20 - USB or SD Just Added SD Card Method at Bottom of this Post
10 Step Program
Pulled from Website dated: Monday August 06, 2007 by ??? if someone knows, I'll give credit.
Recovered and Updated Monday October 27, 2009 by SuperSport
because the WiKi has vanished
Hard SPL will allow you to flash cooked ROMs without SuperCID’ing your device and also will protect your device from being bricked in a bad flash. If a bad flash occurs it should remain in bootloader, and you can re-flash another ROM.
Caution!!! Flashing Hard-SPL will Probably Hard Reset your device!!!! Backup all data FIRST!!!
Before you proceed, check which SPL is on your device:
*** Enter Tri Color Screen ***
--Unplug your phone from USB - Helps to avoid freezing USB Ports
--Hold down the Power & Camera Buttons
--While still holding them down, press the Reset Button using the Stylus
--Release the Reset Button, but continue to hold the Power/Camera buttons until you see the Tri Color Screen
*** Enter Tri Color Screen ***
If your SPL is 1.30.Olipro, 1.20.Olipro, or 9.99 CP, then you already have Hard-SPL on your device and can skip flashing HardSPL, although, I recommend using Olipro 1.20 to avoid problems.
If you want to continue flashing Olipro HardSPL 1.20:
Press the Reset Button using your Stylus. Wait for your phone to start back into Windows. Plug the USB Cable into your phone and PC. Verify ActiveSync or WMDC is connected properly. Now you can Flash.
1. Download "Olipro HardSPL 1.20.zip" in attachment below
2. Unzip the Files, and Run the Program "Olipro HardSPL 1.20.exe" This is a small AutoFlash file I created using Olipro 1.20
3. Windows Vista and Windows 7 may confirm you want to run the program. Choose YES.
4. Check the check box, click ‘Next’
5. Also Check this check box, click ‘Next’
6. In the next window, click the ‘Update’ button
This will show the version number of the ROM, radio, or in this case bootloader that you are about to flash.
7. After the version number has appeared, click 'Next'
8. In the following window, click ‘Next’, your phone may ask if it's ok to run the program, Tap 'Yes'.
(After you click this, the flash will begin, so do not disconnect your device or do anything on your computer)
9. A Progress bar will appear on your computer screen, and your trinity will display a grey screen with progress bar. Be patient while your device is being updated. This will only take a moment.
10. Once your device is finished updating, if it did not automatically soft reset, Press the Reset Button with the Stylus. Click the ‘Finish’ button to exit the RUU program.
To confirm Hard-SPL is on your device, re-enter Tri Color Screen following directions above. You should see the following:
Hard SPL 1.20.Olipro
TRIN100
IPL-0.50 (your device may show IPL-1.00)
TRIN100 MFG
SPL-1.20.Olipro
CONGRATULATIONS!! You have now installed Olipro's Hard-SPL 1.20 on your device using USB Method!! Press the Reset Button with your Stylus to restart.
**********************************
Alternate SD Card Method
**********************************
For those who would rather use their SD Card for this (Maybe your USB Port is not functioning). For this method, the way I'm describing, your phone must be running a version of Windows Mobile. Can be any Version, 5-7. If your phone does not currently run, flash back the OEM ROM that came with it Originally. You can find some in my signature.
Caution!!! Flashing Hard-SPL may Hard Reset your device!!!! Backup all data FIRST!!!
1. Be sure you have a, Non-SDHC, SD Memory Card.
2. Be sure the card is formatted Fat32 and Without a Label.
3. Download the attached HardSPL SD.zip file and extract it's contents. Copy both files, SSPL-TRIN.exe and TRINIMG.nbh, to the Root of your SD Card.
4. On your phone, use File Explorer to browse to the Root of your SD Card.
5. Tap the SSPL-TRIN.exe file. This should run the file.
6. On some phones, you will see a security message come up. Select 'Yes' to run the program.
7. You should now see a Grey screen with Blue Lettering. It will be asking you to Press power button. Go ahead and press the power button.
8. You will see the update progress for a short moment, it will restart, and update again, then show "Update Complete - UPDATE SUCCESS" If you see this message, it has worked.
9. Press the Reset Button with your Stylus to Restart
10. Delete the two files from your SD Card (TRINIMG.nbh, SSPL_TRIN.exe). To confirm Hard-SPL is on your device, Enter Tri Color Screen following directions above. You should see the following:
Hard SPL 1.20.Olipro
TRIN100
IPL-0.50 (your device may show IPL-1.00)
TRIN100 MFG
SPL-1.20.Olipro
CONGRATULATIONS!! You have now installed Olipro's Hard-SPL 1.20 on your device using SD Method!! Press the Reset Button with your Stylus to restart.
Maybe if this could be Stickied?
Thanks, it's a very nice guide for Trinty users, clean and detailed, I also recommand using Olipro 1.20 and not 1.30 to avoid problems, especially with 6.5 roms the annoying "WLAN ERRROR" sometimes seen in bootloader mode ...
Yes, make this "Sticky"
Brds,
nAr
Thanks narshorn! Someone else posted this a long time ago on a WiKi I believe, and I just recovered what I could of the original web page and then rewrote it to work with my files. The original page was removed from it's server, so I grabbed as much of the cached version of it as I could, thus, I don't know who did the original.
Also, thank you for the confirmation of using Olipro 1.20 and not 1.30. That was my belief, and I've heard others, but I'm glad you confirmed.
noob here, need help on flash HardSPL.
i encounter error when trying to update my hardSPL. when i try to flash when my phone is tri color screen mode, this error pop out.
ERROR [270]:UPDATE ERROR
The image file is corrupted. please check your update utility.
info update:
at last i manage to flash my phone to hardspl 1.20, i boot my d810 in normal mode, establish active connection with window, then the flash carry on without any error. but the phone hard reset
but, i wonder y i cant flash to hardspl in tri color screen ???
update to 1.20 spl Olipro true sd card not USB
hi and Thanks for so nice explanation. there is a way to update spl with sd card? my USB connection is faulty. if s/o know please let me know how.
tzuki1 said:
hi and Thanks for so nice explanation. there is a way to update spl with sd card? my USB connection is faulty. if s/o know please let me know how.
Click to expand...
Click to collapse
Just added SD Method to bottom of post #1. Good Luck!
thongkh said:
noob here, need help on flash HardSPL.
i encounter error when trying to update my hardSPL. when i try to flash when my phone is tri color screen mode, this error pop out.
ERROR [270]:UPDATE ERROR
The image file is corrupted. please check your update utility.
info update:
at last i manage to flash my phone to hardspl 1.20, i boot my d810 in normal mode, establish active connection with window, then the flash carry on without any error. but the phone hard reset
but, i wonder y i cant flash to hardspl in tri color screen ???
Click to expand...
Click to collapse
Because stupid me forgot that if you don't have HardSPL on your phone, then TRI COLOR SCREEN flashing is not possible. Doh! FIXED above.
Thank you for bringing this to my attention. When I physically went through the steps, I forgot I still had HardSPL on my phone from previous.
I just went through the steps AGAIN after removing HardSPL, and verifed it works correctly as listed in Post #1.
thankz for promptly reply
btw, what d diff between HardSPL 1.20 and 1.30?
thongkh said:
thankz for promptly reply
btw, what d diff between HardSPL 1.20 and 1.30?
Click to expand...
Click to collapse
I've seen many reports that 1.30 caused issues. Olipro, 'the guy who made our Trinity's safe for Flashing', stopped updating the thread, but if you read it, you will find many users reporting problems and asking for the thread to be updated to go back to 1.20.
I've been using 1.20 since it was released, and have NEVER had a problem with it. And believe me, I Flash a LOT!!! I'm expecting my poor Trinity to catch fire any day now.
Oh... Thx for the tutor...that what i need now...
Good job someone remembered howto
Thanks for the reminder - managed to forget how to enter tri-colour screen in the three months since I last reflashed.
I need help here
I have tried each of the methods.
though your explanation and step by step instructins are very clear, istill can't seem to get Olipro's HSPL on my phone. in the case of using active sync, after it enters the tri color screen nothing happens again and the i get an error message (ERROR 260).
When i tried using the SD method, when i tapped the SSPL_TRIN file, it goes stright to the tri color screen ths is the information i have there
TRIN100
IPL-SSPL by Des
TRIN100
SPL-1.07.ds
and for this reason i can seem to flash any rom with success each time it only gets to the tri colou screen and i get the ERROR 260 message.
Anyone with any idea on how i can fix this.
thanks in advance
redoxy said:
I need help here
I have tried each of the methods.
though your explanation and step by step instructins are very clear, istill can't seem to get Olipro's HSPL on my phone. in the case of using active sync, after it enters the tri color screen nothing happens again and the i get an error message (ERROR 260).
When i tried using the SD method, when i tapped the SSPL_TRIN file, it goes stright to the tri color screen ths is the information i have there
TRIN100
IPL-SSPL by Des
TRIN100
SPL-1.07.ds
and for this reason i can seem to flash any rom with success each time it only gets to the tri colou screen and i get the ERROR 260 message.
Anyone with any idea on how i can fix this.
thanks in advance
Click to expand...
Click to collapse
Did you copy the TRINIMG.nbh file to your SD Card also? Was your SD Card formatted FAT32 and No Label?
Using the SD Method, you do not need to be connected to your Computer. Copy both files to SD and do all work from phone.
Let me know if that works or not.
Remove the HARDSPL...
Hi,
How can I remove the HARDSPL from my Trinity and go back to the original?! Thanks!
sergiopedro said:
Hi,
How can I remove the HARDSPL from my Trinity and go back to the original?! Thanks!
Click to expand...
Click to collapse
Only do this if you do not plan to flash any more Custom ROMs, and would like to stick with the OEM ROM (You may Brick your Phone if you flash from the Stock SPL):
Download the "HardSPL SD.zip " file from the first post.
Extract the files
Copy ONLY the "SSPL_TRIN.exe" file to your SD Card.
Run the "SSPL_TRIN.exe" file from your SD Card (This puts your phone into a special mode that will allow the HardSPL to be overwritten)
Now, your phone should be in bootloader mode with:
TRIN100
IPL_SSPL by Des
TRIN100
SPL_1.07.ds
At this point, you can flash your OEM ROM that includes the Original SPL and IPL.
I use this one: http://www.mediafire.com/?v5yjt1zvgjm
Hi all
I have tried to flash with usb but i'm having a problem
i'm using active sync and after i click 'execute' at the mobile screen it enters the tri color screen and it disconnects the usb port. I get an error message (ERROR 246) that says the device is not responding.
I've tryed several times and it has the same behavior...
The tricolor screen shows this message:
TRIN100
IPL-SSPL by Des
TRIN100
SPL-1.07.ds
i havent try the sd method because i dont have a sd card right now...
Thank you
rcpamr said:
Hi all
I have tried to flash with usb but i'm having a problem
i'm using active sync and after i click 'execute' at the mobile screen it enters the tri color screen and it disconnects the usb port. I get an error message (ERROR 246) that says the device is not responding.
I've tryed several times and it has the same behavior...
The tricolor screen shows this message:
TRIN100
IPL-SSPL by Des
TRIN100
SPL-1.07.ds
i havent try the sd method because i dont have a sd card right now...
Thank you
Click to expand...
Click to collapse
Your mobile screen is showing the correct information, with the exception of USB not showing. As soon as you get to the Tri Color Screen, try removing then reconnecting the USB connection and see if that makes any difference.
Also, when the Tri Color Screen comes up, does your computer ask to install a driver? If it does, be sure to allow that.
SuperSport said:
Your mobile screen is showing the correct information, with the exception of USB not showing. As soon as you get to the Tri Color Screen, try removing then reconnecting the USB connection and see if that makes any difference.
Also, when the Tri Color Screen comes up, does your computer ask to install a driver? If it does, be sure to allow that.
Click to expand...
Click to collapse
Well i just trying all steps again and it worked just fine...go figure!
Thank u anyway
rcpamr said:
Well i just trying all steps again and it worked just fine...go figure!
Thank u anyway
Click to expand...
Click to collapse
Glad to hear you are going. Now you are safe to flash custom ROMs.
Also, remember that each time you flash back to the OEM ROM for any reason, it replaces the HardSPL with the stock one. You will then need to flash the HardSPL back again. At least this is the case for the OEM that I use.
SuperSport said:
Glad to hear you are going. Now you are safe to flash custom ROMs.
Also, remember that each time you flash back to the OEM ROM for any reason, it replaces the HardSPL with the stock one. You will then need to flash the HardSPL back again. At least this is the case for the OEM that I use.
Click to expand...
Click to collapse
ok. thank u so much!
I really need some help!
I was following the the post The DEFINITIVE MTTY Thread!! REVISED 02-11-09 and I made a mistake as follows;
blanktruth said:
Ok, first of all I did not think that it was this dangerous to use MTTY!.
I followed everything and came to these lines
---------------------
Cmd>task 8
Cmd>
---------------------
But after Cmd>task 8 my device restarted immediately before the second line Cmd> appears and I panicked and disconnected my device and pushed the wrong buttons while "Touch Diamond" logo was on the screen.
Now, nothing happens. I can not start from the beginning because I can not start the bootloader by pushing Vol Down and the small red reset button...
Is there anything else left for me to try? Or should I throw my HTC to garbage?
Click to expand...
Click to collapse
Now, I do not know how, but I brought my HTC to bootloader mode and now I can see it via MTTY. But I mistakenly formatted the Internal Storage while I was trying to bring my HTC to bootloader.
Is there any way to upload the DIAMIMG.nbh file to Internal Storage? Or should I follow a different way to save my HTC Diamond?
i have the same probnlem!! with my diam300
my bootloader show not Diam300 64m but only 64M on the first position in 3color mode... plz help
Connect the Diamond and run the customruu.exe from your desktop, this should work.
how to connect if i used mtty... its clear everything what i have on device storage and in bootloader canot start stock or developed rom...
if i want start hard spl its say invalid model it....
blanktruth said:
I really need some help!
I was following the the post The DEFINITIVE MTTY Thread!! REVISED 02-11-09 and I made a mistake as follows;
Now, I do not know how, but I brought my HTC to bootloader mode and now I can see it via MTTY. But I mistakenly formatted the Internal Storage while I was trying to bring my HTC to bootloader.
Is there any way to upload the DIAMIMG.nbh file to Internal Storage? Or should I follow a different way to save my HTC Diamond?
Click to expand...
Click to collapse
The only thing to do now is to flash back a stock ROM or use a custom ROM with the RUU.
Solved!...
Dom1n8tr1x said:
First of, your device is supposed to soft-reset after the "task 8" command and you should have been holding down the "Volume Down" and "Back Buttons" to begin flashing your new ROM. The whole idea of using MTTY is to format your Main Storage and flash a new ROM. Therefor you should have loaded the ROM that you wanted to flash onto your Internal Storage.
Click to expand...
Click to collapse
Thank you for your reply.
Actually I had uploaded the ROM to my internal storage, but during trying to bring my phone to bootloader mode, I formatted the internal storage...
Anyway, what I did now is, first I opened the USB Connection feature from ActiveSync, and then used CustomRUU.exe to Flash the ROM...
Everything is solved now...
Thank you very much all...
ilijan said:
how to connect if i used mtty... its clear everything what i have on device storage and in bootloader canot start stock or developed rom...
if i want start hard spl its say invalid model it....[/QUOT
bootloader is all you need to revive the phone
connect it to usb in bootloader mode and just install an oficial diamond rom from an windows xp pc.
it's easy
Click to expand...
Click to collapse
plz write here step by step guide how you solved
How it was solved...
ilijan said:
plz write here step by step guide how you solved
Click to expand...
Click to collapse
Actually the most crucial part was to bringing phone to boot loader mode. And I think I managed that by pushing the Volume Down and Back (the arrow pointing left) buttons immediately after restarting my phone. And I had to do this after taking out the battery and putting it back after 5 sec.
When I pushed these buttons at the start up the phone tried to install the ROM from my internal storage, but as I explained I had deleted it by mistake. Therefore it could not find the ROM. I disconnected my phone from my PC and the screen started to say something like Retrying USB connection or waiting for USB connection, something like that.
I restarted my PC in Digitally Signed feature disabled by pressing F8 during start-up. Reconnected my phone to PC (the screen of the phone was still blinking as waiting or retrying usb connection). And voila the phone screen changed to boot loader mode...
The rest was easy. I opened the USB connection feature from ActiveSync and used CustomRUU.exe with a ROM to flash my phone...
That is all...
1. plug phone in to computer in bootloader
2. run customruu or stock from rom update on computer
3. wait for rom to flash to device
4.???
5.profit
but my booloader dont show model ID: DIAM300 64M what i had befor
and show me only: 64M
and any flash error with invalid model id, i canot flash, rom, stock rom, or hardspl...
understand me.. im not totaly noob... i used mtty X times... but now have this probles
can somebody help me?
my diamond dont have model id...
before i had in bootloader mode DIAM300 64M model id, but now i havent got... its show only 64M,
every rom flash stopped at 1% cose model id error,
every hard spl falsh finished 100% but after flash when device restart write model id error...
i cant do anithing... can somebody help me?
For everyone facing problems after flashing his/her device, take a look at the link in my sig.
There you can find a guide to restore your diamond.
you dont understand me..
i canto flash any rom any hard spl becous my diamond dont have device ID...
in bootloader dont show DIAM300 64M but only 64M
after all flash say error mobile ID...
i try mtty, hard reseted, soft... and nothing
after start its show me only first stock screan, the red text on the right bottom sight dont start: 1.17.25.14
2.100000
geny d2x
its maybe wrong but i forgot what waz here...
how can change device model ID? form 64M back to my stock DIAM300 64M?
Try another version of Hard-SPL, some people report that 1.40 not fully works.
I suggest you try 1.94 Olinex.
my diamond is death... if somebody know how can heal it... plz write me...
my device ID is missing... so i cant flash any rom, any hard spl, any radio...
try this? http://forum.xda-developers.com/showthread.php?t=409425&highlight=invalid+model+id
im not sure but i dont think one can brick his/her phone after hard spl, thats the reason of hard spl in the first place that u dont brick it. boot loader is always present
Guide
if you are using Windows XP try the following steps:
Connect your device to your PC
In Active Sync > connection settings > check Allow USB connections (which you have un-checked while doing MTTY)
Find a ROM with CustomRUU.exe / diamond wrapper
Now enter into bootloader mode(forget about the device ID)
Go to customRUU.exe and run it
Follow the ROM installation steps
This will help you installing your new ROM.
I had a similar problem and i resolved it by follwoing the above steps.
Guide
if you are using Windows XP try the following steps:
Connect your device to your PCIn Active Sync > connection settings > check
Allow USB connections (which you have un-checked while doing MTTY)
Find a ROM with CustomRUU.exe / diamond wrapper
Now enter into bootloader mode(forget about the device ID)
Go to customRUU.exe and run it
Follow the ROM installation steps
This will help you installing your new ROM.
I had a similar problem and i resolved it by follwoing the above steps.