I was becoming an expert in flashing...but the cable became undone during a flash :-(
Now it restarts to a blank screen with R1.50.08.11 / G32.83.7020 etc. but goes no further.
Computer no longer sees device.
Used hard keys to go into bootlocker. (IPL 0.50 / SPL- 1.07.000)
My VISTA :-( computer sees device.
Then try RUU, but this gives a 270 error.
Tried moving to XP, but the computer does not install the software for the USB port, so now the RUU gives 200 error. Arrgh.
Question: How to update from a very corrupted ROM? Or where can I find the drivers for the USB port, for XP. and if I do can I do the update from the hard bootlocker?
Any help really appreciated!
MS
Update
Found USB drivers for Windows XP
But getting identical problem as with Vista :-(
Device not seen unless in bootlocker mode.
RUU starts and after 1% quits with 270 error - image file corrupt.
Tried RUU a hard SPL (olipro) but same 270 error occured.
Help still needed...
MS
I think you have to flash original HTC rom prio to try other roms
i got a similar problem here, my vista can find trinity only when it is in bootloader mode.
my experience is that connect tinity to vista when it is in bootlader mode, then i can flash a new rom.
after that tinity can sync with vista only via bluetooth.
for your case, maybe you really need restore your trinity to official rom first.
sailer1983 said:
i got a similar problem here, my vista can find trinity only when it is in bootloader mode.
my experience is that connect tinity to vista when it is in bootlader mode, then i can flash a new rom.
after that tinity can sync with vista only via bluetooth.
for your case, maybe you really need restore your trinity to official rom first.
Click to expand...
Click to collapse
Maybe helps:
http://trinityguides.info/index.php?option=com_content&task=view&id=20&Itemid=66
The trinity upgrade guide does not help here.
I can connect to device I have sorted out all the VISTA and XP issues.
The problem is at 1% status the 270 error occurs.
The telephone is actuall a Swisscom 1510. Original ROM was lost in first flashing, have searched but not found official update.
Is there a mini-ROM or a windows WM5 lite ROM which may overwrite what happens while still using the hard bootloader?
MS
Use SD card method.
See wiki page.
Bye
Hi,
...or .... MTTY Procedure....
BYE, Bobo
Tried SD card method - nothing happens. Just sits in Bootloader :-(
Try this procedure
In windows Vista use the attached driver in order to recognize your Device.
If your device is already recognized from windows vista replace the drivers with the drivers in the zip drive.
You have to use the drivers in the attached file not the windows default drivers VERY IMPORTANT!!!
After your Windows vista recognized your device try to flash it
Cheers
Thanks for all the help....but still I am having no success.
The HTC trinity is recognised in both Vista and XP when I use bootloader. (ie HTC USB SYNCH in device manager. Without boot loader the device is more or less dead.
I tried the SD crard trick - nothing happens.
Tried mtty.exe - just get cannot open USB port (on both VISTA and XP).
Nevertheless, the bootloader sees the USB port and the RUU goes to 1% then stops so some communication is happening.
Any other ideas?
MS
The final and, j' m sure, the definitive solution:
Try this one http://forum.xda-developers.com/showthread.php?t=308691&highlight=stack+in+bootloader
Just before I try splxploit, as a note I got this out of mtty
Cmd>info 8
Block 0x0(0) is Reversed block
...
Block 0xC(12) is Reversed block
Block 0x335(821) is BAD block !!!
Seems my problem must be here. Is there another fix besides splxploit?
MS
Install Olipro hardspl 1.20.
Bye
Dear, carefully look that thread again. Stack overflow for Trinity.
It's all my advise. I think you don't do right "Stack method" to get out your problem.
Best regard.(rest calm and do it again).
Uhm, try to download some rom again? and try Rom NVID (no vendor ID) for example. ???
Quick update...
Tried SD card - get 00068002 loading .... then goes to IPL0.5 SPL 1.07
mtty info 8 shows bad blocks
task 2a doesn't clear bad blocks because of CID lock
Tried various hard-SPL OLIPRO 1.2 1.3 etc, to unlock CID - to no avail.
Can the CID not be unlocked through mtty?
MS
ManStan said:
Quick update...
Tried SD card - get 00068002 loading .... then goes to IPL0.5 SPL 1.07
mtty info 8 shows bad blocks
task 2a doesn't clear bad blocks because of CID lock
Tried various hard-SPL OLIPRO 1.2 1.3 etc, to unlock CID - to no avail.
Can the CID not be unlocked through mtty?
MS
Click to expand...
Click to collapse
So you haven't yet tried splxploit?
END of STORY
YESSS!
POF you are a genius - Splxpoilt worked a dream.
Had to run unbrick.bat once. Hit soft reset, and run again as explained in the readme.
This got a good SPL on the machine - then a standard RUU worked a dream.
At the same time I got the SD card update working too...
OK, OK, so I should have tried splxpoit earlier. But I think I had to do the rest first to understand what was going on.
Strange thing is if I look at my machine again under mtty, there is still the Bad block (821). Who cares, I am unbricked!!!
By the way, this board is just completely amazing.
THANKS TO ALL....
i have the same problem
could you help me . how did you repair your spv?
Related
Hi all thanks for looking at my thread.
I'm try to upgrade my Dopod D810 and i encounted a problem and would really like some help here.
The steps i thought i should take were the following
Run...
Unlock and CID Unlock
HardSPL
Radio
ROM
However, after running the Unlock and CID Unlock, i tried to run HardSPL.
But i come accross the "ERROR [246] DEVICE NOT RESPONDING" when i run the ROm update utility.
On the PDA with the 3 color screen
TRIN100
IPL-SSPL by Des
TIN100
SPL - 1.07.ds
and in the white "USB"
what have i done wrong? should i have no ran the UNLOCK and CID Unlock? if so how do i revert this? and what are the correct steps to take to upgrade this?
I am a hermes user and i've done exactly what i did to my hermes to his one.
Please help me.
Kind Regards,
Jason
---------------------------------
guys please, i tired reading the wiki and it told me to run SSPL-TRIN on my device.
i ran it, tired running the utilites again and i get the same problem.
the wiki and text documents says that as long as my SPL ends in a ".ds" i should be able to flash any rom without a problem but i still cant.
all i want is to have a english ROM and the current radio
please help masters. i keep getting "ERROR [246] DEVICE NOT RESPONDING" when i try to flash LVSW lastest rom.
kind regards,
jason
----------
I have been able to upgrade the radio to 1.41.
but i still get ERROR 246 when i try to upgrade the ROM or HardSPL
I'm waiting for help and will be very greatful when someone responds.
Kindest regards,
Jason
have you tried to run the RUU again (leaving the device connected in bootloader, tri colour screen) after you get the error?
Same problem here...
Alternative flashing method.
I just can tell I success using MiniSD with TRINIMG.nbh and execute SSPL-TRIN.exe to flash it. Hope this help. Read Wiki for details.
EDIT
ok i understand that you are suggesting that i use my SD card to Flash the ROM in.
If this is successful i will be greatful but will i have to do this everytime from now on rather than through the computer?
jason
racerx_ said:
have you tried to run the RUU again (leaving the device connected in bootloader, tri colour screen) after you get the error?
Click to expand...
Click to collapse
Ok so i've tried to flash a ROM/HardSPL using the SD card.
i;ve rename the file to TRINIMG.nbh
and then i;ve loaded it in to the bootloader.
however i get a quick flash of a grey background with the word "Loading" and then it just goes to the tri color screen and nothing happens.
the Tricolor screen shows
TRIN100
IPL-0.50
TRIN100
SPL-1.20.Olipro
(white area) Serial(or USB)
Please someone help me out.
a member has mentioned that it is because i do not have Super CID and i should run the unlock. but i have done so.
please guru's of trinity! help me!!!
Personally, I've never been able to flash my phone from the SD card. Never tried before Hard-SPL, but certainly since it just does not work. Need a Windows XP machine (my vista 64 bit won't work - can't find the 64 bit driver for USB bootloader mode). Find yourself a windows pc!
nealed said:
Personally, I've never been able to flash my phone from the SD card. Never tried before Hard-SPL, but certainly since it just does not work. Need a Windows XP machine (my vista 64 bit won't work - can't find the 64 bit driver for USB bootloader mode). Find yourself a windows pc!
Click to expand...
Click to collapse
My attempts with the SD have not work, when i put the SD card in and put it in to boot loader, i get a quick flash of Loading and its just stuck on the tricolor displaying
TRIN100
IPL-0.50 (could this be the problem?)
TRIN100
SPL - 1.20.Olipro
(white area) serial
i do have a windows XP home machine.
man this is stressing me out. please guru's help me out
ok i dont know how but i've some how been able to upgrade to the lastest LVSW. there is a god (i've always known)
how i did this was i was trying to run HardSPL again. It went in to the bootmode while the Utitlty on the computer gave ERROR 246.
So i thought i'd run LVSW, and what do you know? it work! and upgraded!
the question i have is
when i load the bootloader screen i get
TRIN100
IPL - 0.50
TRIN100
SPL - 1.20. Olipro
but then ERROR 246 occurs
i get
TRIN100
IPL-SSPL by Des
TIN100
SPL - 1.07.ds
So does anyone know what is wrong with my Trinty?
What do you bootloaders show?
---------------------------------
edit.
i;ve also noticed that after successful being able to upgrade to LVSW when i look at device info.
my radio hasnt actually upgraded, but back when i wasnt able to upgrade the rom it said i had 1.41.
but now i only have radio 1.16. but i have been able to upgrade to radio 1.41. now.
I just use TRIN-SSPL.exe and make it go into SuperCID Bootloader mode. Then it ask me to confirm whether I want to flash it, press [Power] to continue and it work.
MJRL said:
Same problem here...
Click to expand...
Click to collapse
are you using xp or vista? If you have vista try that on a windows xp machine. I have seen that many time on my p3600.
Just my 2 cents
First time with vista, but after read so many problems with vista i've tried with xp, but gave same error has jasonchiu, i'll try has he did,ignoring the error
Is it possible that other files on the MiniSD?
Try format the memory card and write the files.
I am running Vista so this the only way for me,
I used this method to flash WM5 and WM6.
On the memory card, only
TRIN-SSPL.exe and TRINIMG.nbh
and the device is not SuperCID.
I have a TyTN with official Russian WM6 onto it, which includes 1.16 radio version. I want a newer one, because this seems unstable, so i decided to update just radio (i don't want any cooked ROM or whatever for now).
Each new version of radio I found here failed earlier or later on a Vista x64 computer with error 260. What I have tried is 1.54.07.00 and 1.54.00.10 and 1.50.
To my surprise, packaging is different, but the effect is the same: after "Verifying the image on your device" (i can hear USB disconnecting and connecting back as the device enters bootloader) they time out with 260.
Right now I'm trying to revert what have I done to Vista as it won't allow me to turn off driver signing, as advised.
Ah, this doesn't work either (same error 260).
What am I doing wrong? My bootloader is, as said on that screen:
Code:
HERM200
IPL-1.01
HERM200
SPL-1.40.Olipro
Yes, I have installed some...er...thing before, maybe it was called "HardSPL", but it didn't come handy and wasn't any use to me as I decided against cooking a ROM.
Update: What I like the most is, despite all my attempts the device still works! Other than the radio troubles, that is.
I've updated from an SD card.
Try this my friend... http://www.mrvanx.org
Thank you, I did.
Please note the x64 drivers are unsigned so to use them successfully you must disable driver signing.
Click to expand...
Click to collapse
This is what I'm unable to do, but I suppose is beyond this forum.
Hi
I have had the same problem with my x64 vista pc and the 260 error msg. It took me hours but what seemed to finally fix it for me was to:
1. completely remove WMDC from the pc, reboot the pc,
2. reinstall WMDC plus upgrade,
3. uncheck the allow USB connections option on your 8525, exit out of the window, then do a soft reset
4. now make a USB connection w the PC
Let us know how it works
Sorry, you'll have to wait till my next upgrade Everything is working so far - so until I need something that can't be achieved using SD flashing I'll stick to this technique. Thanks for the advice anyway.
Hi,
I tried to upgrade my XDA using Ranju's latest updater, the whole process failed and now I'm stuck at the BL screen "USB" at the top (when connected, otherwise it says "serial") and "v1.00" at the bottom.
My PC, SyncCentre and Windows Mobile Device Centre (I'm using Vista) all show the device as being disconnected (up until trying to upgrade everything had been fine).
As it's not showing up on my PC all of the software options for recovering it dont fail, all end with a plethora of USB not connected errors etc
I've tried the how-to on the wiki: http://wiki.xda-developers.com/index.php?pagename=Uni_Stuck_Bootloader_Serial to no avail.
Does anybody have any ideas? Greatly appreciated,
Thanks,
Lee
with jasjar-bl1.01-ruu-v1.2 I always restart my JJ Leave your uni in bl and start the application Good luck......
I think the Vista is not the problem this upgrade don't use AS or "in italian centro gestione dispositivi WM"
Bye
M.C.
Well, I flashed my Qtek a while ago, it failed to flash (using Vista) and doing a hard reset after it whas hanging at the startupscreen(the one with all the rom/radio numbers). No matter what I tried, following the instructions on Vista windows mobile center all failed... The good news is that your computer and your PDA still see when it is connected, ie USB/Serial, like in my case!
I then tried it on my desktop/XP, it flashed without a problem...
The funny bit is that I flashed my herald (WM6) 2 times using Vista without any problem...
I cannot explain but if U have the possibility, try and see if it works on XP...!
Good luck!
are you trying to flash it WITH your SIM card and / or SD card inside? If so, try taking them both out! It worked for me a few times!
I would start by getting rid of vista !
i had the same xprience
the different was i downgrade from wm6 to wm5 (i need the vcall)
failed in vista, succeed in xp
-> my advice : try in xp !! don't forget to remove the sd card
Manual for how to flash a rom in Vista
Read this post, you have the solution to the problem here:
http://forum.xda-developers.com/showthread.php?t=313001
You need to update the driver manually, if not, will not be able to install the driver.
You need to do this without sd/sdhc and without the sim.
If you follow these instructions, you can flash with success.
Greetings.
Kali.
Hi, all, i have problem with my SPV 700 (HTC 3600) - Trinity.. When I turn on it, I see only start screen eith HTC logo, (you'll see it in attachments) there is only M 05 B05, R 1.50.08.11, g 32.83.7020.20h, D 3.00, i can do nothing... I cant reflash ROM because my computer cannot find it, and instalation write updater is old, you must find newer updater.. When i install acivesync, it cannot find too, but my installers (5 downloaded) will start, but write Cannot find hardware. (or mobile phone). Is any program, to connect my htc, or reflash ROM?
I found Schaps_WM6Pro_Trinity_4.30.2008_WWE_Full(p3600I) or some next, but every write cannot connect. Thank you very much.
Load from mini SD!?
You can try loading your ROM from mini SD card !
You need to format sd card to FAT32 with Card Reader first!
Read this post:
http://forum.xda-developers.com/showthread.php?t=454123
and
http://forum.xda-developers.com/showthread.php?t=441787
Have you tried to hard reset, leave the device on tricolor screen and retry loading ROM?
Use the proper SPL to load!
If you are a Windows Vista user - the driver from this site it will be the sollution - search for it!
I cant go to tricolor display, i cant reset, i cant do anything, i thing it freeze.. sorry my english, im from slovakia. Or.. how I can go to tricolor mode? I try all combination clicks.
Power+Camera+reset button with ur touch pen
sorry, im stuppid, i now find reset button
FOR ALL RESET BUTTON IS NEAR USB CONNECTOR
http://www.hardreset.eu/htc_touch_cruise_polaris_hard_reset_soft_reset.html
but it dont work, i connect to pc, (no activesync but i connent) but when it sending new rom it still on 0% and cancel it.. i cant unlock CID. probably i havent good program.. I try HTC_Hermes_SIM_CID_Unlock_v3a and HTC_Trinity_SIM_CID_Unlock_v1, but nothing... this cannot find my device.. but HTC_Hermes_SIM_CID_Unlock_v3a find it, sending go to 7% but write I havent compatibile mobile phone with this software. What can I do?
OverrideCrash said:
sorry, im stuppid, i now find reset button
FOR ALL RESET BUTTON IS NEAR USB CONNECTOR
http://www.hardreset.eu/htc_touch_cruise_polaris_hard_reset_soft_reset.html
but it dont work, i connect to pc, (no activesync but i connent) but when it sending new rom it still on 0% and cancel it.. i cant unlock CID. probably i havent good program.. I try HTC_Hermes_SIM_CID_Unlock_v3a and HTC_Trinity_SIM_CID_Unlock_v1, but nothing... this cannot find my device.. but HTC_Hermes_SIM_CID_Unlock_v3a find it, sending go to 7% but write I havent compatibile mobile phone with this software. What can I do?
Click to expand...
Click to collapse
Man please read from instruction from the passage named HARD RESET, the button you are talking about its for software reset only!
Use the seq. Power+Camera+reset!Keep each button pushed and then use stillus for reset and you will get the Tricolor screen - but first format your SD like i describe in the post #2 and then copy your ROM on it!
exactly the same problem here. i tried to re install gelly_01 greek rom. The only requirement i did not follow was the connection with active sync. I am using Vista and the connection with the pc invokes the windows mobile device center. I tried to reinstall through a xp vmware with activesync but i get an error 270.
Any thoughts?
I am trying to find sth relevant.
thnx!
check this thread
http://forum.xda-developers.com/showthread.php?p=1923734
manos4596 said:
exactly the same problem here. i tried to re install gelly_01 greek rom. The only requirement i did not follow was the connection with active sync. I am using Vista and the connection with the pc invokes the windows mobile device center. I tried to reinstall through a xp vmware with activesync but i get an error 270.
Any thoughts?
I am trying to find sth relevant.
thnx!
Click to expand...
Click to collapse
Hard reset your phone first, then use the bootloader method(Camera+Power+Reset then in the bootloader connect the usb cable)!
First try this http://forum.xda-developers.com/showthread.php?t=299659
If not - read carefully the instructions from here:
- http://trinityguides.info/index.php?option=com_content&task=view&id=39&Itemid=66 - all you have to know about hard SPL and how to do.
Anyway, also try to change the Rom image that you have used when you bricked your device!Try a new ROM by the date of release!
Thnx for the advice! I got it working. Before reading your reply I had started installing the original rom provided by htc (WM5). It installed correctly and at least i have my phone back. I will check your links about hard SPL (thanx ) but i had installed the gelly_01 rom before , not through vista though.
I will try to reinstall it.
It's getting late here so i will check it tommorow and infirm you.
Regards.
problem solved Its working now, but I dont know how i repair it
for unlock CID HTC_Hermes_SIM_CID_Unlock_v3a.zip (Its not compatibile, but my opinion is it unlock but dont repair rom) then i give there [P3600i] HardSPL v1.1.rar and end is Trinity_WM_6.1_NEW.OS_19965_Diamond_edition_by_Akeo_V3.1.rar all files are in attachments.
I give there HTC_Trinity_SIM_CID_Unlock_v1.zip too, before Akeo Diamond edition.
This can be closed now. Thanks for all thank you ! Here are lot of good peoples really thx
slimul said:
You can try loading your ROM from mini SD card !
You need to format sd card to FAT32 with Card Reader first!
Read this post:
http://forum.xda-developers.com/showthread.php?t=454123
and
http://forum.xda-developers.com/showthread.php?t=441787
Have you tried to hard reset, leave the device on tricolor screen and retry loading ROM?
Use the proper SPL to load!
If you are a Windows Vista user - the driver from this site it will be the sollution - search for it!
Click to expand...
Click to collapse
Thanks a lot . i had the same problem but now my htc is back to life
i
i still have the problem with the rom , i just do every thing and don't work can any one cold help me
sorry the bad english
Okay, I've searched alot to get this thing solved. When I try to update my rom, the update starts normally, but then my telephone screen turns black, my gets disconnected, windows tells me it has found new hardware. The update failes and returns error 260 (connection lost). When I soft-reset the telephone afterwards, it returns to it's old shape.
Info about my telephone.
Rom: 1.93.404.1 NLD
Radio: 1.0025.05
PC: Windows XP SP 3, Active Sync 4.5
I tried to update with this rom: RUU_Diamond_HTC_NLD_2.03.404.3_Radio_Signed_Diamond_52.51.25.26_1.09.25.23_Ship.exe
I also tried to update to Hard-SPL but that gave me the same error.
PLease guys does anyone of you know how to fix this? (personally I think it's windows xp which is screwing up).
Thanks in advance, I appreciate all help.
Yours, Martijn.
Even the tiniest tip may help (A)
I had the same trouble with that rom, I tried from internal memory and it worked. Search the wiki I am sure the info is there.
"ERROR [260] : UPDATE ERROR
This error occurs when there is an "open port error" before upgrading the CE ROM image. Solution: You can reset the device and run RUU again. If you still encounter an "OPEN PORT ERROR" again, reset your computer and try again."
This is what the WIKI tells me. But I have tried that. How did you manage to perform the update on the internal storage? Because I tried that with hard-spl but it wouldn't work.
Besides I only have .exe files for the Hard-Spl and the official rom from HTC.
Thanks for your reply though.
EDIT PART, just read this on another thread in the wiki:
ERROR 260 (Update Error):
"Your phone is not connected to ActiveSync. Check your connection or restart the phone. Also make sure in ActiveSync that "Allow USB connections" is checked (under File->Connection Settings). If this still doesn't help, then remove the memory card and SIM card before flashing."
I'm going to try this now, if it worked, I'll let you know
Just found out I have a CDMA version or something, I'll try google for the problem now.
Get the rom image from your temp directory and look here, found in the wiki
http://wiki.xda-developers.com/index.php?pagename=Diamond_FlashfIS
Does the hardware install incorrectly? My laptop did this on XP.
XP would find the new hardware, my bootloader would say USB. Then it'd tell me new hardware could not be installed properly and from there my phone suffered those symptoms - Back to where I was. Funnily enough it eventually fixed itself.
dickenz said:
Does the hardware install incorrectly? My laptop did this on XP.
XP would find the new hardware, my bootloader would say USB. Then it'd tell me new hardware could not be installed properly and from there my phone suffered those symptoms - Back to where I was. Funnily enough it eventually fixed itself.
Click to expand...
Click to collapse
It looks alot like your problem yes. But last time the hardware installed correctly, then the patch I found for CDMA models on ppcgeeks failed, and my telephone got bricked. So I'll need to get that fixed first. After that I'll sure think twice before I try another rom update :/
Thanks for all the help though, and I have to advice everyone to not use the hard-spl for cmda users from ppcgeeks unless you're 100% sure it fits your model!