Hi all u guys out there hope someone can help me i installed this rom on my diamond the name was TEAL or some like that the first few times it was fine but then my battery was running low and then when i turned my diamond on again i had 2 setup mobile and now it just keep showing the screen that says it wanna setup and i cant acess USB from there so plz if u can help me recover my diamond plz reply
try update from Boot Screen
Blackster..try updatin frm boot screen..go in boot screen & then connect it to usb & try updatin the ROM...
to get in your bootscreen just reset your device while holding the volume down button
just so you know ^^
Tried every thing
,My vista wont show the usb from hardSPL and i cant connect from the setup and when i just installed the rom again it wont work
nothings work plz help
USB??
its just installing the usb driver but show no usb
simple thing
just run RUU from u'r PC...
Follow 1st Two steps by clicking next...
no need to perform mentioned task in RUU.
Connect USB Cable PC to Diamond...
On diamond hold on off button and volume down button and hit reset button on back..
you will forwarded to boot screen on diamond...
It will automaticly identify u'r USB connection to PC...
Once it displays USB on diamond boot menu, Hit Update button on RUU running on PC...
Then follow the RUU instructions...
Once finished, you have done...
Related
Hai ,
I tried different flashes of WM6 , then i reverted back to wm5.
But then again i flashed it with wm6 rom.
It flashes it successfully but after hard reset , pressing 0 , it just stays at splash screen giving infos in red.
I am stuck at spalsh screen ... any ideas ?
Also tried uni_exitbootloader .. but still stucks at splash screen
Tried Refalshing it many times but same ..
babablacksheep said:
Hai ,
I tried different flashes of WM6 , then i reverted back to wm5.
But then again i flashed it with wm6 rom.
It flashes it successfully but after hard reset , pressing 0 , it just stays at splash screen giving infos in red.
I am stuck at spalsh screen ... any ideas ?
Also tried uni_exitbootloader .. but still stucks at splash screen
Tried Refalshing it many times but same ..
Click to expand...
Click to collapse
Try enter bootloader and re-flash WM6 Rom, if it still fails to boot, search the Universal forum for MTTY commands to reset partition tables. I suspect the partitions are corrupt.
Hope youre battery is not too low.
Cheers,
Beast
babablacksheep said:
Hai ,
I tried different flashes of WM6 , then i reverted back to wm5.
But then again i flashed it with wm6 rom.
It flashes it successfully but after hard reset , pressing 0 , it just stays at splash screen giving infos in red.
I am stuck at spalsh screen ... any ideas ?
Also tried uni_exitbootloader .. but still stucks at splash screen
Tried Refalshing it many times but same ..
Click to expand...
Click to collapse
Something like this happened to me when I first flashed my Universal, I tried something in the Wiki (Cannot remember?) That told me to use that usb port from now on for all flashing. After that it worked. I will search further to see if I can help...
Okie Problem Solved.
I did this to get myself sigh if relief.
100% working
1. Take out the SD and SIM cards
2. Opened ActiveSync and go to file, connection setting and Un-check "Allow USB Connections". Then press Ok and close ActiveSync
3. Put in bootloader mode (Power + Light + reset) which brings up the "un-backlit" screen with "Serial" at the top and v0.XX at the bottom
4. Plug in USB cable DIRECTLY from PC to Jasjar (MAKE SURE NOT TO USE A USB HUB). You MIGHT then see a warning window complaining that an "Unsigned" device driver is being attempted to be installed. You will be prompted to either "STOP INSTALLATION" or "CONTINUE ANYWAY" - this warning can be safely ignored and so just click on "CONTINUE ANYWAY".
5. Open mtty utility / software
6. Select USB from the "Port" drop-down on the upper left corner of the dialog box and hit OK
7. Then another screen will come up. Hit enter and that will show "USB>"
8. Type "task 28 55aa" and hit enter. {type it manually/ don`t copy and paste commands}
9. use the "Original OEM ROM" that is made for your device and update with it (CE,Extended and Radio) Flash all
10. Hard Reset
Also if your device bootloader version is lower than "v 1.01" you should update that first (before installing the OEM ROM, but NOT before "Task 28 55aa").
After this is complete you may then use your device again.
NOTe : I find you must kill the wcescomm, wcesmgr and rapimgr exe's using task manager before you get the 'usb' option in mtty (kills activesync)
Please,
what to do when there's no USB port in mtty (only COM1 and COM2) ?????
babablacksheep
must say -Thank you!
vjj said:
Please,
what to do when there's no USB port in mtty (only COM1 and COM2) ?????
Click to expand...
Click to collapse
You must disable ActiveSync before connection
and put in bootloader mode (Power + Light + reset) BEFORE run MTTY
after USB must appear in drop-down menu
one more time thanked babablacksheep
while doing the gps upgrade, I was doing step 4 (Run the Alltel ROM exe file ) it failed at 8% then sent me to a recovery page after i removed the battery my touch wont do anything ,i tried soft reset ,camera and even hard .the only time i see anything is when i plug a usb cable in ,just a red light in the speaker hole.
try getting it to bootloader (hold power button, camera button and soft reset button) it should display a tricolor screen. now just plug in the usb cable and reflash the same rom or a different one
tried that it didn't work
What is the bootloader version you are using? 0.4 or 2.31
If you see 2.31.CoKE, you should be fine, but read more, more, more!!!
Don't want to sound like I'm not helping, but I am no expert right now, so don't want to further cause damage to your phone.
So go here:
http://forum.ppcgeeks.com/showthread.php?t=24979
i'm having a somewhat related problem..
I rom updated.. phone works but get a USB not recognized error when i plug it into any xp box.
I guess i need to try an activesync cab file..
if that doesn't work.. i'll reflash a rom through SD method once i find out how.
Anyone got a link for that?
Hello All,
My HTC Diamond Handset serial no is HT826K******* Tryed to change the ROM , but after reaching to 100% also the completed mesage is not coming . When I press the reset button Tri colour screen appears with error messgae " Upgrade ROM code error Please try Again".. . Please help
You probably don`t have the correct update package for your device... If you really want to update to this rom then you need the HardSPL. Install the HardSPL 1.93 Unsigned Developer edition.
do you have Hard-SPL?
I Recently updated through ROMUpdateUtility know i see touch diamond screen with RUU_Signed_1_93OliNex_HSPL_UnsignedEdition ...Please help
just flash another ROM while in bootloader and connected to usb. I would suggest to use a simply rom.
Hi,
But How , I am not able to copy the file to Internal memory as when I connect to laptop the the internal memory is not visible:
you don't need to put the nbh file in internal storage. Turn your device off. Press and hold the volume down button. While doing so press the power button. Keep holding the volume down button pressed until you see the multi colored screen which is called the bootloader. At the bottom it should say Serial. Using the USB cable with which you sync to your PC, plug the cable in to your PC and then plug the other end into your device.
The multi colored screen should soon say USB at the bottom of the screen. You are now ready to flash a new ROM. Just run the RUU as you would normally.
I did that; know I got the tri colour scree ;which says USB in white area know how to run RUU , my htc is connected to my laptop
create a folder on your pc and name it anything. now copy the nbh ans ruu.exe in that folder. run the ruu by double clicking it. this should be done when you get usb on your screen, if done correctly you rom flash should start flashing and a bar will appear on your phone.
Thanks All
Hi All,
Problem got fixed .
Solution used:-
Unsigned-Hard-SPL-Diamond-OliNex(2)
rumbles said:
you don't need to put the nbh file in internal storage. Turn your device off. Press and hold the volume down button. While doing so press the power button. Keep holding the volume down button pressed until you see the multi colored screen which is called the bootloader. At the bottom it should say Serial. Using the USB cable with which you sync to your PC, plug the cable in to your PC and then plug the other end into your device.
The multi colored screen should soon say USB at the bottom of the screen. You are now ready to flash a new ROM. Just run the RUU as you would normally.
Click to expand...
Click to collapse
so wut happens if i get no usb then wuts the matter ???
need to know what problem i have becuase i can never connect the fone via usb
Dynomite232 said:
so wut happens if i get no usb then wuts the matter ???
need to know what problem i have becuase i can never connect the fone via usb
Click to expand...
Click to collapse
Do you have the correct drivers installed?
Or Windows Mobile Device Center?
I think you need that I'm not too sure, I do anyway
hello. sorry for my poor english. i am trying to install a ROM on my htc diamond but when the flashing starts my phone looses connection to my pc (active sync) this happends when the 3 color lines is shown on my phone's screen. do anyone know how to fix this problem. thanks
ROM Update
xvision1992 said:
hello. sorry for my poor english. i am trying to install a ROM on my htc diamond but when the flashing starts my phone looses connection to my pc (active sync) this happends when the 3 color lines is shown on my phone's screen. do anyone know how to fix this problem. thanks
Click to expand...
Click to collapse
Hi!
Not sure if that works but if this is your first time to flash the drivers to recognize your device in bootloader mode needs to be installed which takes some time.
Try to put your device into bootloader mode (keep VolDown pressed during reset) than plug in USB. Diamond screen at bottom will change from Serial to USB if recognized and device drivers installed.
Now start up ROM Update and perform flash. You should MTTY before every flash.
Regards,
Cina.
If this is a spam, plz forgive me
Well, 2 all. I booted my Diamond with a 6.5 ROM. Normallt, it worked well. But this time, the ROM got some mistake that when it was goin' to finish, it froze it still kept the static in 30 mins later, and I got to reset it. Then, my Diamond restarted, and... froze at the Bootloader screen (3 colors screen) ( I tried all things to recover it, searching on the web, but nothing's ok I plugged it into my PC and my PC doesn't recognize it ( anyone knows out there plz help!!!!!!!
which version of windows operating system are you using. also try to reset and then again go into bootloader MANUALLY by pressing volume down key. see if the pc detects. also do you have ur stock rom?
meteorain08 said:
If this is a spam, plz forgive me
Well, 2 all. I booted my Diamond with a 6.5 ROM. Normallt, it worked well. But this time, the ROM got some mistake that when it was goin' to finish, it froze it still kept the static in 30 mins later, and I got to reset it. Then, my Diamond restarted, and... froze at the Bootloader screen (3 colors screen) ( I tried all things to recover it, searching on the web, but nothing's ok I plugged it into my PC and my PC doesn't recognize it ( anyone knows out there plz help!!!!!!!
Click to expand...
Click to collapse
enter bootloader, connect to PC. in white bar the 'Serial' will change to 'USB'
then you can run customeRUU to flash again
if the PC don't detect, try on other PC.
Well, if u know how to up ROM via PC then tell me, because I often up ROM directly on my Diamond, not via PC. And I plugged it to PC and the word "Serial" disappeared, but the word "USB" did not display on the screen
Did you make MTTY befor instal 6.5 rom try to make it and reinstal the rom