Develop Bugs

HELP!!!!

:?
I tried to make an update with the file JASJAR_WWE_11353_137_10301
Suddenly the Display stop et 99% of the extended Rom Update and on my monitor was an infomation like "an error happend"
After this, nothing else happend .
Yes, realy nothing happens anymore. I cant start the device not with power, not with reset or with power+reset
nothing nothing nothing
What can i do
If i start to try a new update, it schows me no information about what rom etc. is installed or what will be installed. if i then start i get the notice, that it is the wrong device.
Help me please. ist there any way to put the mda back to live?????
I guess i dont only need an update but the complete software

HELP!!!
I have the exact same issue after the upgrade. Nothing will happen. I spent several hours trying resets, combination of button pressed, removed battery, resets, just to try to get back the boot loader mode but nothing is happening.
there has to be a way to do this and I hope someone on this board had that issue before and got it resolved.

I had a similair issue with my old XDA II, it turned out my storage card was corrupted. Use a card reader to check your storage card is OK, perhaps format the storage card (having saved any data first of course) and see how you fare

Have had the same problem wirh a radio ROM update on my QTEK9000. The anly thin that still worked was the hard reset. After the hard reset the device still did not respond. But when i connected it to the PC I could start the updateprocess of the original ROM. I took about 20 minutes for the whole procedure and than the Qtek9000 was back in factory default (Pffff and I could breath again).
So perhaps you can try a hard rest and then connect aganin to the PC.

I allready tried this!
But nothing happens.
Even if i put the power device or the usb into the mda, no LED schows anything. just sometimes the LED is red for not more than a minute. if it then goes out, i get the message "Unknown usb device" in my PC

Are you in bootloeader mode? Do you see the words USB or Serial on the screen of the Universal in Portrait mode. Note: Backlight is off so you have too look real hard, but it should be there

no, i see nothing.

I had quite a hard time yesterday while upgrading. The bootloader is very hard to see, use a torch to lite up your display. In portrait view on the top should be the word serial or usb, on the bottom v1.00.
I also did a hard-reset in this stage, but it just returned to the bootloader menue.
If I connect to the PC and the device is recognized I see the word serial in the display change to USB. For me I do not know the reason but my PC did not want to fulfill the upgrade process. Needed to take another PC (Laptop) to solve the problem. After the upgrade of the ROM, You still need to upgrade the Radio (this was my experience) before a cold-reset will put You back to business.
Good luck.
Ruud

Having the exact same problem as gary_b and having performed quite a few upgrades, I can confirm there is absolutlely nothing on the screen. The unit will not go into bootloader mode or even able to do a hard reset. It is not recognized when plugged in the USB.
When connected to power and the hard reset procedure is done, the red charging light will come up for less than 1/2 seconds and disappear.
I tried all different combination to make it boot but nothing. If I could at least get it to bootloader more, I can revive it.

Feel very bad I cannot help here.
I was wondering Yesterday about one thing. IF, during all this upgrading process, the battery runs out, (as it does not seem to charge during upgrade process) will it show bootloader screen ?
Would it be possible to get a loaded battery from somebody to check yours ?

That is a good suggestion to try out, but I have been unable to find anyone that has that device. It might be simply a drained battery.
Mine got corrupted I think at the end of the upgrade right after I did a regular reset instead of teh power and reset procedure.
However, I would think that even with no battery in, the unit should power back up when plugged in no?

Maybe an idea for somebody who is doing upgrading now, and is in bootloader status anyway.
Take out the battery, but connect with USB to PC with ASync. Does the bootloader state show ?
I am sorry to not do it for myself, if You saw my desperate state Yesterday, You will believe that I am not willing to see that bootloader screen for some time, sorry.
Ruud

now i know what to do:
Nothing!!
I went to a service-point with my mda pro and there was nothing to do with it.
If this happens the complete memory is "killed". Like "format c:" and while format is running you switch out the power.
Thanks god: I got a new MDA pro because i did not tell them (in the store)that i tried an update!
But i called the service-line before anf they told me that there is nothing to do!
But thx

Wow, can't say that this is good informatuin for those with this problem, but very glad it worked out for You.

I ve had this problem 5 minutes ago. Finally a took out the battery. Then connect to AC and Red led is on. Then i put the battery, tried hard reset and message to confirm hard reset in the screen (wellcome to life, jasjar).Then i run radio update again and it's upgrading rigth now....buffffff

I almost suffered a heart attack when this happened an hour ago. Have found that the update works fine if the SD card is taken out... phew.

Not even stuck at Bootloader :(

Please help!
I just upgraded my ROM to Ivan's latest AKU3.5 from bootloader
This completed successfully (100% successful, disconnect and restart etc)
I disconnected and reset, except it was stuck in bootloader mode
I tried the Mtty method (for the first time ever) and followed the step by step instructions...
...after a few seconds a few command lines appeared with "USB>" on the last line
I took this to mean the process had finished (?), disconnected the device from USB and tried a soft reset
the device just stayed stuck in bootloader
next, i downloaded uni_exitbootloader and ran it (as this has worked for me many times in the past). it didn't work the first few times, but i disconnected and reconnected and this time it worked. It said "data sent, you can now reset your device"
This maybe where i went wrong?
I foolishly reset the device before disconnecting it from the USB. The PC immediately said "USB device not recognised" and the screen of my Universal went blank
Now, if i soft reset, it does nothing, i cannot even put it back into bootloader using the camera, on, reset button combination.
HOWEVER, if i press the two soft keys (as if i was going to do a hard reset) i get the white screen with the black text saying "Press 0 to restore etc"
If i press 0, it says "clearing" but the screen just goes blank
If i press x, the screen just goes blank
Now i am completely unable to try and use either mtty or exitbootloader as my PC just says "USB device not recognised" and neither applications run as they should
QUESTION: Have i totally bricked my Universal?!
If not, what can i possibly do...???
As usual, i will be extremely greatful for any advice or assistance to resurrect my favourite Pocket PC!
Thanks in advance for your help.

Aaagh! I think i just realised what i did...
1. I didn't read the posting "For all those stuck in the bootscreen, try the Mamaich method" carefully enough. I didn't realise that the Mamaich method totally erased the ROM!!!
2. By not flashing a new ROM to the device immediately and instead using exitbootloader to exit the bootloader screen i now have a device that has no ROM and probably has no way of knowing how to get into bootloader mode.
Can someone confirm this?
For one, i feel like an idiot for not reading the posting carefully, but having admitted to being stupid,...
... is there anything at all i can do???
Please help...

cancel that, you already said what i was going to ask above

have you try to flash it again with original ROM? sometimes it helps!

Once in bootloader mode, try plugging it into a different USB port, one directly on the PC.
I have had this where one port says not recognised, even after having been plugged in and used for ages, then I go to flash it and it won't work.
Another port has worked for me.

Since you ereased the DOC, all you've got to do now is to reflash the default ROM.

Thanks everyone...
Only problem is, i cannot get it into bootloader mode. And every port i plug it into (so far) says "device not recognised"...
Nevertheless, i did try to reflash the device, but it just gave me the "Error 150" message. It just doesn't know the device is connected i guess?
I think if i hadn't done the Exitbootloader step then i would have been able to reflash it. However, now that i have... i'm a bit stuck... any ideas of other ways to get the device into Bootloader mode?

try
you already know there is a file called EXITBOOTLOADER but did you know that here is a file called ENTERBL ?
try it .....

Thanks dhob187!
Where might i find this file though? Did you mean to attach it?
Just one other question...
How does ENTERBL work if the PC doesn't recognise my device i.e. "USB device not recognised"? Will the application override this and push commands to my pocket pc anyway?
Or is there a way i can get my PC to stop rejecting the device when i plug the USB in?
Thanks in advance,

I believe this is the file u needed
i don't know how this utility works, but just yesterday i stuck in the bootloader after upgrading my uni to AKU 3,5 and solved with ExitBootloader.exe. CMIIW it works the same way, just plug the USB cable then execute the utility (just simple as that).....
but have u tried my earlier suggestion? my friend got the exact problem like you (blank LCD not even bootloader), he was downloaded the original EXEC ROM and try to flash with it (with original upgrade utility also). and the thing start to blink, enter the bootloader and flashing!.....after he manage to wake the device up, then he tried to flash it again with the newest ROM and succeded........
sorry for my english.....

Please don't apologise for your English, thank you for your suggestions!
I didn't quite understand your initial post... but i do now.
Does it have to be the first ROM that it was shipped with or just an original i-mate JasJar ROM?
I can't try it now, but i'm excited to go home and give it a go later tonight... what's more i'm excited at the prospect that there may be some hope for my currently rather expensive paperweight!!!
If the aforementioned doesn't work, i'll try using your attachment.
Cheers again!

it doesn't have to be the first rom that shipped with your imate, just an original one. try your luck then! never give up, keep the faith!!!

sorry, forgot one thing, just ignore the USB error (not recognized) and go for the upgrade (execute the original upgradeUt.exe)

Hi Rudy173.
Thanks for your help, but unfortunately nothing has worked
I have tried running two official JasJar Roms without success... i always get the connection error message (this is surely because the PC always says "device not recognised" when i plug it in).
Also, when i run ENTERBL.exe i just get a failure saying that ...ENTERBL.exe is not a valid WIN32 application... etc...
So unfortunately, i'm still stuck... any further suggestions anyone?
Can the i-mate service centre help me? Is it likely to be expensive?

Back in business )
Wow, not entirely sure what i did... but my Universal is ALIVE!!!
As per the previous post, nothing seemed to be working so i removed Activesync 4.5 beta and reverted to 4.1. I then tried to reflash to an original ROM and the same "connection error" problem happened.
However, next time i tried to enter bootloader, by pressing light, on/off and reset, it went straight into bootloader and i was able to reflash from there
I didn't even need to reflash with an original i-mate ROM. I went straight for Ivan's latest.
This experience has taught me a few things:
1. I have become seriously attached to my Universal!
2. You should never give up hope of retrieval!!
3. This forum is full of very nice helpful people!!!
Thanks everyone.

wow! glad to hear that!
Happy ending....................

Hopeless HTC s621

I have my device unlocked already and have done many ROM upgrades before, this time my PC froze half way throught the upgrade. The device turns on and gets stuck on the T-mobile screen. It doesnt connect to active sync i cant even get Dashv2unlock to detect my device. Please help somebody.

from what i've read before about this type of issue (somewhat), try removing the battery and SIM for a few minutes, then replace and reboot and see if active sync recognizes it now.
if this info is no longer valid, I apologize.

I think you need to have your phone in bootloader mode and then flash again. Make sure the phone is off, and while holding down the camera key (to the right of the space key), connect the USB cable to your phone. The tri color bootloader screen should appear on your S620. Now run the upgrade file on your PC again.
Let us know how it goes....

im able to get to the tri color screen but when i start any Rom upgrade it gets to 3 percent and fails. I have also tried the SP-1.11 upgradeonly.exe and also the Dashv2Unlocker that i have paid for. Nothing

Diamond not conecting

I want to upgrade rom on may diamond but when conect the phone to my conputer the phone it just starts to charge. The computer does not detect him and I have activated usb conection on the phone.
I am using a standard miniusb cable used also for canon fotcamera, Nokia N95, motorola V3 (v360 L6, L7 etc.)
I did instaled Activesync on my computer but still no result.

You did no say which Win OS you are using - If Vista then you do not need activesync (AS) but windows mobile device centre or any other Win OS Before Vista then AS is what you need. AS needs to be installed before you connect your phone to the PC.
Have you restarted your PC first before install - this also helps sometimes

Try this....
Start>Settings>Connections>USB to PC and here ....uncheck the box Enable advanced network functionality
Just a reminder to please use the Internal Method when flashing a new Rom or Radio. Do not rely on your PC as errors occur more frequently.

R3PUBL1K said:
You did no say which Win OS you are using - If Vista then you do not need activesync (AS) but windows mobile device centre or any other Win OS Before Vista then AS is what you need. AS needs to be installed before you connect your phone to the PC.
Have you restarted your PC first before install - this also helps sometimes
Click to expand...
Click to collapse
I am using Win XP SP2 and I have tried every thing that you said but nothing.

band27 said:
Try this....
Start>Settings>Connections>USB to PC and here ....uncheck the box Enable advanced network functionality
Just a reminder to please use the Internal Method when flashing a new Rom or Radio. Do not rely on your PC as errors occur more frequently.
Click to expand...
Click to collapse
I did uncheck that box but without any results so now I will try internal method. But I'll have to send the file to the phone via bluetooth and see if it works.

band27 said:
Just a reminder to please use the Internal Method when flashing a new Rom or Radio. Do not rely on your PC as errors occur more frequently.
Click to expand...
Click to collapse
How much is it supose to take "Internal method"?
After pressing Vol_Down + Back button it showed the three color screen then it changed to a white screen with loading on it and it stays like that (after pressing Vol_Down + Back button I didn't press nothing else).

The Internal Method shouldn't take you any longer then 2 min. or so.
Once you have started the flashing to begin in the Grey menu....it will eventually say OK...OK
and yes
at this stage you soft reset and press vol down and centre round button.
Grey menu then gives you a choice to reset back to manufactures settings which is what you want (vol UP)......this should take an additions 2 min. if that.

band27 said:
The Internal Method shouldn't take you any longer then 2 min. or so.
Once you have started the flashing to begin in the Grey menu....it will eventually say OK...OK
and yes
at this stage you soft reset and press vol down and centre round button.
Grey menu then gives you a choice to reset back to manufactures settings which is what you want (vol UP)......this should take an additions 2 min. if that.
Click to expand...
Click to collapse
I have tried everything that you said and nothing.
The only diference is that now when I conect the cable to the phone it asks me witch mode to conect it (Activesync or storage), but the computer still doesn't see's it.

Tried another USB-cable?

chribruu said:
Tried another USB-cable?
Click to expand...
Click to collapse
I tried with 3 diferent cables.

Have you tried putting your device into bootload mode (soft reset & vol. down) and the connecting to your pc. The bottom of your coloured screen should switch from serial to usb....If this switches to USB then you are good to go with downloading what ever Rom using the RUU_
Keep me posted...

band27 said:
Have you tried putting your device into bootload mode (soft reset & vol. down) and the connecting to your pc. The bottom of your coloured screen should switch from serial to usb....If this switches to USB then you are good to go with downloading what ever Rom using the RUU_
Keep me posted...
Click to expand...
Click to collapse
It doesn't switch's to usb it only shows "serial". If I put it into bootmode while it is conected to USB it shows nothing, not "USB" or "Serial" it's blank.
I am begining to belive that there is a hardware problem in my phone.

Do you have .NET framework installed on your PC! if not, get it from http://www.microsoft.com/downloads/d...DisplayLang=en

HTC One X doesn´t start anymore

Hello guys,
I am new here and thats my first post, please tell me when I do something wrong. But I think this is the best forum to ask :
I had a well-functioning HTC One X. But at once it doesn´t start and stuck in the HTC bootlogo. I googled it and after many days I try to unlock the bootloader. The bootloader starts only after many trys and then shows a red field "battery level is too low to flash"(connected to PC). The red led doesn´t lights up. I leave it in the bootloader and after many hours it starts normally (bootloader still locked). I set the phone back to factory settings (not in the bootloader). I used it like every day, but after hours when I switch to the normal menü it was stucked for 5 seconds and then the screen become black and it wont restart. I buy accumulator for the phone and exchange it (I have a little bit "hardware skills"). I connected it with loading cable to the socket (not the PC!). The red LED flashes for a second and then happens nothing. After many trys the bootloader shows up (connected to my PC) and I googled for almost hours to find a solution. "I have to install a custom ROM". I unlocked the bootloader with the programm "One X All-In-One Kit v2.3". I don´t know why but I shut the phone down. I try to start the phone or the bootloader but it doesn´t work. I try it now for weeks but it is dead (but I´m very sure the problem that it doesn´t starts is not due to the unlocked bootloader, because it is the same problem with the "not starting" like the time before I unlocked it). But the strange thing is... and now comes the important part... when I connect the phone with my PC the PC make the "USB connected"-sound and says that there is a unrecognized device connected. And when I try to start the bootloader the PC makes the "USB disconnected"-sound and a second later the "device-driver software not installed"-sound (I hope you know what I mean) and when I keep trying to start the bootloader it happens again and again the same. I tried almost everything, I use a loading.bat file but it can´t detect the phone (you know "unrecognized device"). Is it the accumulator ? Is the hardware dead ? Or what is the problem ?
I hope you understand this text (I´m sixteen and from germany). If you don´t please ask me every question you have. I really hope you can help me with my really long-term problem.
Thanks for every question, reply, solution or improvement proposal for me
XilentMe

So, what i have deduced is that
1. You are stuck on fastboot with low battery.
2. Your PC does not recognize your device.
For this purpose, first download and install the htc usb drivers. These should work: http://forum.xda-developers.com/showthread.php?t=2211791
Then visit this thread: http://forum.xda-developers.com/showthread.php?t=1658084
follow the instructions, once your phone is charged enough, unlock the bootloader, flash a custom recovery, boot into recovery and let it charge for a while, then flash a new rom.
Dont forget to press the Thanks button if i helped

Okay thanks for your proposal, but the problem is now that I can´t boot into bootloader, the phone does nothing. No reaction, no charging LED, no normal boot, no bootloader...absolutely nothing. Only when I connect the HTC to the PC the PC make the "USB-device connected" sound, as if you connect a USB-stick to your PC, but nothing else happens.
Any ideas or similar problems ?
XilentMe

So try to charge via pc. Leave for some time connected to pc and try to power up.

Hey,
I tried it, but it didn´t work. Nothing happens, only the "plug off-sound" when I want to start the bootloader via volume down+power button, while it is connected to the PC. I have no idea what to do.
XilentMe