:?
I tried to make an update with the file JASJAR_WWE_11353_137_10301
Suddenly the Display stop et 99% of the extended Rom Update and on my monitor was an infomation like "an error happend"
After this, nothing else happend .
Yes, realy nothing happens anymore. I cant start the device not with power, not with reset or with power+reset
nothing nothing nothing
What can i do
If i start to try a new update, it schows me no information about what rom etc. is installed or what will be installed. if i then start i get the notice, that it is the wrong device.
Help me please. ist there any way to put the mda back to live?????
I guess i dont only need an update but the complete software
HELP!!!
I have the exact same issue after the upgrade. Nothing will happen. I spent several hours trying resets, combination of button pressed, removed battery, resets, just to try to get back the boot loader mode but nothing is happening.
there has to be a way to do this and I hope someone on this board had that issue before and got it resolved.
I had a similair issue with my old XDA II, it turned out my storage card was corrupted. Use a card reader to check your storage card is OK, perhaps format the storage card (having saved any data first of course) and see how you fare
Have had the same problem wirh a radio ROM update on my QTEK9000. The anly thin that still worked was the hard reset. After the hard reset the device still did not respond. But when i connected it to the PC I could start the updateprocess of the original ROM. I took about 20 minutes for the whole procedure and than the Qtek9000 was back in factory default (Pffff and I could breath again).
So perhaps you can try a hard rest and then connect aganin to the PC.
I allready tried this!
But nothing happens.
Even if i put the power device or the usb into the mda, no LED schows anything. just sometimes the LED is red for not more than a minute. if it then goes out, i get the message "Unknown usb device" in my PC
Are you in bootloeader mode? Do you see the words USB or Serial on the screen of the Universal in Portrait mode. Note: Backlight is off so you have too look real hard, but it should be there
no, i see nothing.
I had quite a hard time yesterday while upgrading. The bootloader is very hard to see, use a torch to lite up your display. In portrait view on the top should be the word serial or usb, on the bottom v1.00.
I also did a hard-reset in this stage, but it just returned to the bootloader menue.
If I connect to the PC and the device is recognized I see the word serial in the display change to USB. For me I do not know the reason but my PC did not want to fulfill the upgrade process. Needed to take another PC (Laptop) to solve the problem. After the upgrade of the ROM, You still need to upgrade the Radio (this was my experience) before a cold-reset will put You back to business.
Good luck.
Ruud
Having the exact same problem as gary_b and having performed quite a few upgrades, I can confirm there is absolutlely nothing on the screen. The unit will not go into bootloader mode or even able to do a hard reset. It is not recognized when plugged in the USB.
When connected to power and the hard reset procedure is done, the red charging light will come up for less than 1/2 seconds and disappear.
I tried all different combination to make it boot but nothing. If I could at least get it to bootloader more, I can revive it.
Feel very bad I cannot help here.
I was wondering Yesterday about one thing. IF, during all this upgrading process, the battery runs out, (as it does not seem to charge during upgrade process) will it show bootloader screen ?
Would it be possible to get a loaded battery from somebody to check yours ?
That is a good suggestion to try out, but I have been unable to find anyone that has that device. It might be simply a drained battery.
Mine got corrupted I think at the end of the upgrade right after I did a regular reset instead of teh power and reset procedure.
However, I would think that even with no battery in, the unit should power back up when plugged in no?
Maybe an idea for somebody who is doing upgrading now, and is in bootloader status anyway.
Take out the battery, but connect with USB to PC with ASync. Does the bootloader state show ?
I am sorry to not do it for myself, if You saw my desperate state Yesterday, You will believe that I am not willing to see that bootloader screen for some time, sorry.
Ruud
now i know what to do:
Nothing!!
I went to a service-point with my mda pro and there was nothing to do with it.
If this happens the complete memory is "killed". Like "format c:" and while format is running you switch out the power.
Thanks god: I got a new MDA pro because i did not tell them (in the store)that i tried an update!
But i called the service-line before anf they told me that there is nothing to do!
But thx
Wow, can't say that this is good informatuin for those with this problem, but very glad it worked out for You.
I ve had this problem 5 minutes ago. Finally a took out the battery. Then connect to AC and Red led is on. Then i put the battery, tried hard reset and message to confirm hard reset in the screen (wellcome to life, jasjar).Then i run radio update again and it's upgrading rigth now....buffffff
I almost suffered a heart attack when this happened an hour ago. Have found that the update works fine if the SD card is taken out... phew.
Related
Please help!
I just upgraded my ROM to Ivan's latest AKU3.5 from bootloader
This completed successfully (100% successful, disconnect and restart etc)
I disconnected and reset, except it was stuck in bootloader mode
I tried the Mtty method (for the first time ever) and followed the step by step instructions...
...after a few seconds a few command lines appeared with "USB>" on the last line
I took this to mean the process had finished (?), disconnected the device from USB and tried a soft reset
the device just stayed stuck in bootloader
next, i downloaded uni_exitbootloader and ran it (as this has worked for me many times in the past). it didn't work the first few times, but i disconnected and reconnected and this time it worked. It said "data sent, you can now reset your device"
This maybe where i went wrong?
I foolishly reset the device before disconnecting it from the USB. The PC immediately said "USB device not recognised" and the screen of my Universal went blank
Now, if i soft reset, it does nothing, i cannot even put it back into bootloader using the camera, on, reset button combination.
HOWEVER, if i press the two soft keys (as if i was going to do a hard reset) i get the white screen with the black text saying "Press 0 to restore etc"
If i press 0, it says "clearing" but the screen just goes blank
If i press x, the screen just goes blank
Now i am completely unable to try and use either mtty or exitbootloader as my PC just says "USB device not recognised" and neither applications run as they should
QUESTION: Have i totally bricked my Universal?!
If not, what can i possibly do...???
As usual, i will be extremely greatful for any advice or assistance to resurrect my favourite Pocket PC!
Thanks in advance for your help.
Aaagh! I think i just realised what i did...
1. I didn't read the posting "For all those stuck in the bootscreen, try the Mamaich method" carefully enough. I didn't realise that the Mamaich method totally erased the ROM!!!
2. By not flashing a new ROM to the device immediately and instead using exitbootloader to exit the bootloader screen i now have a device that has no ROM and probably has no way of knowing how to get into bootloader mode.
Can someone confirm this?
For one, i feel like an idiot for not reading the posting carefully, but having admitted to being stupid,...
... is there anything at all i can do???
Please help...
cancel that, you already said what i was going to ask above
have you try to flash it again with original ROM? sometimes it helps!
Once in bootloader mode, try plugging it into a different USB port, one directly on the PC.
I have had this where one port says not recognised, even after having been plugged in and used for ages, then I go to flash it and it won't work.
Another port has worked for me.
Since you ereased the DOC, all you've got to do now is to reflash the default ROM.
Thanks everyone...
Only problem is, i cannot get it into bootloader mode. And every port i plug it into (so far) says "device not recognised"...
Nevertheless, i did try to reflash the device, but it just gave me the "Error 150" message. It just doesn't know the device is connected i guess?
I think if i hadn't done the Exitbootloader step then i would have been able to reflash it. However, now that i have... i'm a bit stuck... any ideas of other ways to get the device into Bootloader mode?
try
you already know there is a file called EXITBOOTLOADER but did you know that here is a file called ENTERBL ?
try it .....
Thanks dhob187!
Where might i find this file though? Did you mean to attach it?
Just one other question...
How does ENTERBL work if the PC doesn't recognise my device i.e. "USB device not recognised"? Will the application override this and push commands to my pocket pc anyway?
Or is there a way i can get my PC to stop rejecting the device when i plug the USB in?
Thanks in advance,
I believe this is the file u needed
i don't know how this utility works, but just yesterday i stuck in the bootloader after upgrading my uni to AKU 3,5 and solved with ExitBootloader.exe. CMIIW it works the same way, just plug the USB cable then execute the utility (just simple as that).....
but have u tried my earlier suggestion? my friend got the exact problem like you (blank LCD not even bootloader), he was downloaded the original EXEC ROM and try to flash with it (with original upgrade utility also). and the thing start to blink, enter the bootloader and flashing!.....after he manage to wake the device up, then he tried to flash it again with the newest ROM and succeded........
sorry for my english.....
Please don't apologise for your English, thank you for your suggestions!
I didn't quite understand your initial post... but i do now.
Does it have to be the first ROM that it was shipped with or just an original i-mate JasJar ROM?
I can't try it now, but i'm excited to go home and give it a go later tonight... what's more i'm excited at the prospect that there may be some hope for my currently rather expensive paperweight!!!
If the aforementioned doesn't work, i'll try using your attachment.
Cheers again!
it doesn't have to be the first rom that shipped with your imate, just an original one. try your luck then! never give up, keep the faith!!!
sorry, forgot one thing, just ignore the USB error (not recognized) and go for the upgrade (execute the original upgradeUt.exe)
Hi Rudy173.
Thanks for your help, but unfortunately nothing has worked
I have tried running two official JasJar Roms without success... i always get the connection error message (this is surely because the PC always says "device not recognised" when i plug it in).
Also, when i run ENTERBL.exe i just get a failure saying that ...ENTERBL.exe is not a valid WIN32 application... etc...
So unfortunately, i'm still stuck... any further suggestions anyone?
Can the i-mate service centre help me? Is it likely to be expensive?
Back in business )
Wow, not entirely sure what i did... but my Universal is ALIVE!!!
As per the previous post, nothing seemed to be working so i removed Activesync 4.5 beta and reverted to 4.1. I then tried to reflash to an original ROM and the same "connection error" problem happened.
However, next time i tried to enter bootloader, by pressing light, on/off and reset, it went straight into bootloader and i was able to reflash from there
I didn't even need to reflash with an original i-mate ROM. I went straight for Ivan's latest.
This experience has taught me a few things:
1. I have become seriously attached to my Universal!
2. You should never give up hope of retrieval!!
3. This forum is full of very nice helpful people!!!
Thanks everyone.
wow! glad to hear that!
Happy ending....................
I have flashed many Custome ROM's before. I have HardSPL installed on my phone.
I tried flashing to a ROM (I forget which one now, I think Cloudfa or something) and it stopped at about 15%. The Update utility stopped as well.
I cannot connect to bootloader at all. I tried holding down on Volume down/Reset to enter bootloader, but the thing is that it's already in bootloader with the message "Upgrade ROM code error, Please try again"
ActiveSync doesn't see my phone either. In fact all it does is just sit on the bootloader screen with that error...
Please Help... Thanks You...
A normal soft reset still brings you back to Bootloader?
What happens when you plug in your device? Does it not change from serial to USB at the bottom?
band27 said:
A normal soft reset still brings you back to Bootloader?
What happens when you plug in your device? Does it not change from serial to USB at the bottom?
Click to expand...
Click to collapse
Sorry. Yes it does show USB when plugged in, but won't respond to anything that I have tried software wise. It does not switch from this bootloader/error screen at any point. Even after I pull my battery and turn it back on...
I have yet to come across a thread which has this exact problem...
jzalapski said:
Sorry. Yes it does show USB when plugged in, but won't respond to anything that I have tried software wise. It does not switch from this bootloader/error screen at any point. Even after I pull my battery and turn it back on...
I have yet to come across a thread which has this exact problem...
Click to expand...
Click to collapse
Have you tried flashing a different ROM while in bootloader?
^^ Yes. It give me an error on my computer...
I would like to try the internal flashing method but I don't seem to have a way of getting at my Storage Card.
I found this thread with a similar problem
http://forum.xda-developers.com/showthread.php?t=480022
I WAS just able to get off of that screen I was talking about, but the best I get is to the Touch Diamond Screen that lists my ROM and such. So no real progress.
I have a feeling that I would resolve my problem if I could Flash from the Interanl Storage...
Have you tried hard resetting the device?
Pull out stylus and Holding....1) Vol. Down 2) Center Round button 3) then press red button aka soft reset with stylus
Nothing...
im stuck
hi all i am very new to this im not sure what i have done or how to fix the problem i download these this morning and they worked
rom version 1.57.831.1(47324)wwe
radio version 1.14.25.24
protocol version 52.64.25.34u
when i bootload in tri colours screen it shows
BLAC100 32M
SPL-1.56.OliNex
MicroP-Blackstone (led)v6
if it shows that i must of done something right i think of what ill read
and i have windows 7 ulitmate and i have Miri_WM65_21815_V19.0_Premium
when i double click on the BLACKSTONE RUU WRAPPER it crashes then i rename a new folder and done it from there and it works but it comes up wit error 208 file open? then i got told to rename to ruu_signed.nbh file to blacimg.nbh and to store it in the root of my sd card done that then somehow i got it to come up to the screen by Turn off the phone, press and keep pressed volume down button and while keeping it pressed turn on the phone then i see a message "Press power to flash your device" and i press power to flash got to 0% and it crashed and come up with Upgrade ROM code error plz try again and stuck in bootloader mode but now it wont even turn on its dead it wont turn on no matter what i do can someone plz help
all i want to do is get windows mobile 6.5 working i cant understand that it can be so hard to do
thanxs blueboys25!
Im Not sure exactly what happened here, I've been flashing for nearly a year now a variety of ROMs, and this last time seems to have been fatal.
I went from a custom ROM, did the routine task29 before loading a new ROM; the task29 completed, I returned to bootloader to load the new ROM, and it wouldnt load past 0%. I tried to task29 again, and then that wouldnt load past 0%.
I've since tried mtty and doing set 14 0, task 29, task 8, which restarts it, but now I can no longer manually power it on by pressing hardware keys anymore.. I have to leave it plugged into USB and wait for it to auto-turn itself on after about 5 mins, it loads to "Touch Pro 2" screen, then I can press the little reset button and hold down vol key to get to bootloader. However, it only lasts there about 10 second before turning itself off again, showing the orange light like it's charging. Sometimes I am quick enough to get any ROM or manual HardSPL to try and load at bootloader, but it still sits at 0%.
I have also tried to load a ROM from the SD card, which seems maybe the only option how; however, I have heard you need at least 50% battery, and I have no way to see how much battery I have left, or whether its even charging.
I tried to install from SD yesterday, and got to the gray "Loading" screen, and it just sat there.. I wasnt sure how long it normally takes at that screen, so i powered it off, checked my SD card and now that shows as corrupt and cannot even be formatted... pretty much burnt out as well now, it seems.
Did I do the SD card installation right, using my RHODIMG.nbh file at the root? How long does it normally sit at the Loading screen? I have an 8GB mini-sd I could load from, but I dont want it to burn out as well..
Are there any other options?? I cant even send back to warranty, I dont think, because I cant even load back on the stock ROM or relock it...
Moved to Rhodium General forum because not a cooking problem.
Someone please help... I just tried again to load stock ROM from SD card, as well as custom, it just sits on "Loading..." on the gray screen...
Just for the record, I can get into bootloader, but as of now nothing will load past 0%.
I tried mtty set 14 0, task 29 and task 8, no luck...
I'm certainly not an expert, but just thought I'd throw out a few ideas.
Have you tried charging the phone on the wall charger (not USB) for several hours (like overnight). The fact the phone is powering off by itself suggests that you may be low on battery. USB won't charge the battery sufficiently in some cases of extreme low battery. Try another battery or charge if possible.
Having the RHODIMG.nbh file in the root of your micro-SD card is the correct way to boot from the card. Normally, it doesn't matter if there are other files on the card. But formatting it can't hurt at this point.
Only other thing I can think of, is try to re-flash the radio first, and see it that helps. That's all I can offer up at this point. I was going to suggest trying to flash the stock ROM, but you've already thought of that in your latest post.
Good luck!
redpoint73 said:
I'm certainly not an expert, but just thought I'd throw out a few ideas.
Have you tried charging the phone on the wall charger (not USB) for several hours (like overnight). The fact the phone is powering off by itself suggests that you may be low on battery. USB won't charge the battery sufficiently in some cases of extreme low battery. Try another battery or charge if possible.
Having the RHODIMG.nbh file in the root of your micro-SD card is the correct way to boot from the card. Normally, it doesn't matter if there are other files on the card. But formatting it can't hurt at this point.
Only other thing I can think of, is try to re-flash the radio first, and see it that helps. That's all I can offer up at this point. I was going to suggest trying to flash the stock ROM, but you've already thought of that in your latest post.
Good luck!
Click to expand...
Click to collapse
Thanks for the response; I just tried that (flashing the radio) and it didnt work. Ive also tried flashing a variety of ROMs and nbh files over SD;
It always seems to freeze at the gray "Loading..." screen and get no further.
venomshot629 said:
Thanks for the response; I just tried that (flashing the radio) and it didnt work. Ive also tried flashing a variety of ROMs and nbh files over SD;
It always seems to freeze at the gray "Loading..." screen and get no further.
Click to expand...
Click to collapse
Try using a different USB cable to flash via the PC. If you try the SD route again, some users report that using a NON-SDHC card solves the flashing problem. Give that a shot and then report back. I can't really think of anything else offhand.
cajunflavoredbob said:
Try using a different USB cable to flash via the PC. If you try the SD route again, some users report that using a NON-SDHC card solves the flashing problem. Give that a shot and then report back. I can't really think of anything else offhand.
Click to expand...
Click to collapse
I have tried again using a 512 MB SD card and it still hangs at the "Loading..." screen.
Also, when flashing with any USB cable, I am still stuck at just 0%.. I can get into the bootloader, etc, but it just refuses to flash any image..
I have a nordic HTC Touch Pro 2
This unit started acting up after I installed the Energy ROM from the 20th of December. It used to fail in booting occationally(fixed by attaching USB-power), but now it is thouroughly stuck in the bootloader.
This is what I see when I reboot:
RHOD100 32M SS-BC
SPL-0.85.OliNex
MicroP(LED) 0x0A
MicroLED(KEY) 0x04
TURBO HW/TURBO SW
TP MFG DATA
509,521 792,844
795,200 221,198
226,843 Calibrated
Serial (changes to USB when connected)
There is a quick flash of 2 previous screens, one tri-color and one saying something about no image to load.
I belive, but would be thrilled to be proven wrong, that I have tried all tricks.
Running Windows 7 I first disabled device driver signing and loaded the HTC USB driver. Downloaded mtty 1.42, connected to the phone via USB and ran "boot" command.
The only problem listed was one bad block in CE.
Tried reboot again with same error.
"info 8" revealed that the bad block is 370.
Ran "task 29" but it gave an error trying to delete block 370.
Rebooted and tried to flash latest 29007 Energy ROM. No errors reported during the flash, still when it rebooted after reaching 100% it stopped in bootloader again.
I have also tried this procedure and replaced the Energy ROM with the latest original nordic ROM. When I use "boot" command from mtty I get the HTC screen (white background with htc in green letters) but the phone apparantly is stuck there. A soft restart brings me bach to the bootloader again.
Is my phone bricked? I'm not sure what to do or try next and as I have seen others report my battery is draining and will not charge(no light) when plugged in to computer or charger.
Thanks in advance, I love what you all do for this community and wouldn't have still used tha TP2 if it wasn't for all the great ROMs presented here!
NVM, re-read and see you already tried my suggestion.
Additional info
I ahould add that I also can't do a hard reset. Pressing and holding send and end and then power button only result in getting the bootloader menu. I borrowed a freshly charged battery and tried loading a new ROM, but no change, it still only restarts to the bootloader after completion.
If you can get into bootloader and the usb shows when plugged in, you should be able to flash back to stock via RUU.
Try this;
Open your downloaded ROM with unzipper. You should see two files, the RUU and the RHODIMG.nbh. Copy the .nbh onto the root of your SD card. Powerup the device holding the volume down. It should boot to bootloader and immediatly look for and find the .nhb and install it.
Hope that helps.
Hi!
Thanks for your answers! Sorry about the late reply!
I tested with RHODIMG.nbh file(29007 Energy) on the SD-card. The installation started and ran as expected. When done the screen showed the following info:
"RHODIMG.nbh - OK
OS - OK
Update Complete
UPDATE SUCCESS"
There were no button to press on the screen, and pressing the power-button didn't do anything. I eventually removed the battery, reinstalled the battery and pressed the power button. Unfortunately for me I was once again presented with the bootloader screen.
Any ideas to a new approach? I really don't want to write off the phone as bricked, it should have about a year left in it before I consider replacing it.
Try this:
When powered off, attach headset to the phone. Then press power button.
My Touch Pro2 ran into the same situation recently, showing nothing but a 3-color screen with the same information as you listed. I haven't tried mtty but I found if I plug in the headset, it boots normally. No idea why...
It sounds like an error in the instruction set for the bootloader. Maybe cmonex can help you with a bootloader-friendly version of Hard SPL to re-flash.
cajunflavoredbob said:
It sounds like an error in the instruction set for the bootloader. Maybe cmonex can help you with a bootloader-friendly version of Hard SPL to re-flash.
Click to expand...
Click to collapse
he already has Hard-SPL so he could just reflash it with the Hard-SPL exe in manual mode, but as the version number is the same, the device may skip the updating of the SPL. if the OP wants to try this, I can make one with a different version number. though I seriously doubt that the issue would be fixed that way...
Headset trick
Hi,
Again, thanks to all that try to help me!
I tried the headset trick just now and look and behold, it actually worked! My limited brain can't come up with any plausible explenation but I'm happy anyway
I do remember reading about this trick at some point, but I couldn't locate a headset until today. Thanks lilei105!
Now I will reboot the unit several times to ensure this wasn't just a coincident.
Edit: Booted 4 times, still no problem. Have booted both with and without USB-cable connected to PC.
Yeah my advice would be re-flash it or install/download a different ROM.
i may be way off here, but could it be a problem with the volume down button on the unit? maybe the headset bypasses the standard volume button?
I've got a dead oneplus 5t from my son. It was not charging anymore.. So I've replaced charging cable and battery.. Seemed to work it was charging... However it doesn't boot... No logo screen screen stays black/blank.
Tried several suggestions on this forum to get into recovery mode, fastboot mode... But still nothing. Only vibrating works after a few seconds.
So tried to unbrick with OP5T_Unbrick_tool_dumpling_43_J.40_181105(OOS.5.1.7) and the qualcomdrivers..
I was able to install the drivers and I see they are installed in devicemanagement.. and an empty folder create for oneplus.
I charged the phone all night and was able to download the upgrade. It then says download complete and I tried to restart the phone..
Still just vibrating but nothing happens.. Seems like everything has vanished from the phone, no recovery, no bootloader, no files.
So how to proceed to get all the stuff on the phone? And maybe the displayscreen is dead, but how can I tell?
Also tried the SMT upgrade. Strange thing is the device and com port are seen in devicemanagement and active when I connect without volume up, but cannot start because it says When I try to use smt mode the program says: "This COM port is disable by user". With volume button up pressed and then connect, ledlight turns green but the qualcomdevice is grayed out in devicemanagement and it says waiting for device..
Any help is welcome. I am a noob in how to proceed on the phone however I have an IT background.
Spent already so many time figuring out .. maybe it's effortless and its for the trashbin.
Thanks in advance
SOLVED
I opened the phone again loosened all those tiny connections to battery, screen,charger, mainboard and re-attached them.. Somehow a connection seemed to be fitting allright as yI looked at it, but apparently wasn't :good: