Oneplus 5t black screen unbricktool doesnt seem to work - OnePlus 5T Questions & Answers

I've got a dead oneplus 5t from my son. It was not charging anymore.. So I've replaced charging cable and battery.. Seemed to work it was charging... However it doesn't boot... No logo screen screen stays black/blank.
Tried several suggestions on this forum to get into recovery mode, fastboot mode... But still nothing. Only vibrating works after a few seconds.
So tried to unbrick with OP5T_Unbrick_tool_dumpling_43_J.40_181105(OOS.5.1.7) and the qualcomdrivers..
I was able to install the drivers and I see they are installed in devicemanagement.. and an empty folder create for oneplus.
I charged the phone all night and was able to download the upgrade. It then says download complete and I tried to restart the phone..
Still just vibrating but nothing happens.. Seems like everything has vanished from the phone, no recovery, no bootloader, no files.
So how to proceed to get all the stuff on the phone? And maybe the displayscreen is dead, but how can I tell?
Also tried the SMT upgrade. Strange thing is the device and com port are seen in devicemanagement and active when I connect without volume up, but cannot start because it says When I try to use smt mode the program says: "This COM port is disable by user". With volume button up pressed and then connect, ledlight turns green but the qualcomdevice is grayed out in devicemanagement and it says waiting for device..
Any help is welcome. I am a noob in how to proceed on the phone however I have an IT background.
Spent already so many time figuring out .. maybe it's effortless and its for the trashbin.
Thanks in advance

SOLVED
I opened the phone again loosened all those tiny connections to battery, screen,charger, mainboard and re-attached them.. Somehow a connection seemed to be fitting allright as yI looked at it, but apparently wasn't :good:

Related

HELP!!!!

:?
I tried to make an update with the file JASJAR_WWE_11353_137_10301
Suddenly the Display stop et 99% of the extended Rom Update and on my monitor was an infomation like "an error happend"
After this, nothing else happend .
Yes, realy nothing happens anymore. I cant start the device not with power, not with reset or with power+reset
nothing nothing nothing
What can i do
If i start to try a new update, it schows me no information about what rom etc. is installed or what will be installed. if i then start i get the notice, that it is the wrong device.
Help me please. ist there any way to put the mda back to live?????
I guess i dont only need an update but the complete software
HELP!!!
I have the exact same issue after the upgrade. Nothing will happen. I spent several hours trying resets, combination of button pressed, removed battery, resets, just to try to get back the boot loader mode but nothing is happening.
there has to be a way to do this and I hope someone on this board had that issue before and got it resolved.
I had a similair issue with my old XDA II, it turned out my storage card was corrupted. Use a card reader to check your storage card is OK, perhaps format the storage card (having saved any data first of course) and see how you fare
Have had the same problem wirh a radio ROM update on my QTEK9000. The anly thin that still worked was the hard reset. After the hard reset the device still did not respond. But when i connected it to the PC I could start the updateprocess of the original ROM. I took about 20 minutes for the whole procedure and than the Qtek9000 was back in factory default (Pffff and I could breath again).
So perhaps you can try a hard rest and then connect aganin to the PC.
I allready tried this!
But nothing happens.
Even if i put the power device or the usb into the mda, no LED schows anything. just sometimes the LED is red for not more than a minute. if it then goes out, i get the message "Unknown usb device" in my PC
Are you in bootloeader mode? Do you see the words USB or Serial on the screen of the Universal in Portrait mode. Note: Backlight is off so you have too look real hard, but it should be there
no, i see nothing.
I had quite a hard time yesterday while upgrading. The bootloader is very hard to see, use a torch to lite up your display. In portrait view on the top should be the word serial or usb, on the bottom v1.00.
I also did a hard-reset in this stage, but it just returned to the bootloader menue.
If I connect to the PC and the device is recognized I see the word serial in the display change to USB. For me I do not know the reason but my PC did not want to fulfill the upgrade process. Needed to take another PC (Laptop) to solve the problem. After the upgrade of the ROM, You still need to upgrade the Radio (this was my experience) before a cold-reset will put You back to business.
Good luck.
Ruud
Having the exact same problem as gary_b and having performed quite a few upgrades, I can confirm there is absolutlely nothing on the screen. The unit will not go into bootloader mode or even able to do a hard reset. It is not recognized when plugged in the USB.
When connected to power and the hard reset procedure is done, the red charging light will come up for less than 1/2 seconds and disappear.
I tried all different combination to make it boot but nothing. If I could at least get it to bootloader more, I can revive it.
Feel very bad I cannot help here.
I was wondering Yesterday about one thing. IF, during all this upgrading process, the battery runs out, (as it does not seem to charge during upgrade process) will it show bootloader screen ?
Would it be possible to get a loaded battery from somebody to check yours ?
That is a good suggestion to try out, but I have been unable to find anyone that has that device. It might be simply a drained battery.
Mine got corrupted I think at the end of the upgrade right after I did a regular reset instead of teh power and reset procedure.
However, I would think that even with no battery in, the unit should power back up when plugged in no?
Maybe an idea for somebody who is doing upgrading now, and is in bootloader status anyway.
Take out the battery, but connect with USB to PC with ASync. Does the bootloader state show ?
I am sorry to not do it for myself, if You saw my desperate state Yesterday, You will believe that I am not willing to see that bootloader screen for some time, sorry.
Ruud
now i know what to do:
Nothing!!
I went to a service-point with my mda pro and there was nothing to do with it.
If this happens the complete memory is "killed". Like "format c:" and while format is running you switch out the power.
Thanks god: I got a new MDA pro because i did not tell them (in the store)that i tried an update!
But i called the service-line before anf they told me that there is nothing to do!
But thx
Wow, can't say that this is good informatuin for those with this problem, but very glad it worked out for You.
I ve had this problem 5 minutes ago. Finally a took out the battery. Then connect to AC and Red led is on. Then i put the battery, tried hard reset and message to confirm hard reset in the screen (wellcome to life, jasjar).Then i run radio update again and it's upgrading rigth now....buffffff
I almost suffered a heart attack when this happened an hour ago. Have found that the update works fine if the SD card is taken out... phew.

Desire Z wont power on :(

Hey guys,
Running ILWT CM7. Flashed about two weeks ago. My phone has been working fine except for the past few days where it's been constantly freezing, requiring a battery-out and turn on, and rebooting on it's own.
Last time it froze, I removed the battery and turned back on, and it got to the "htc" logo and froze. After ~25minutes, I took the battery out and tried again.
Phone seems completely dead, won't respond to power on, volume down and power on, no lights come on when charger cable is plugged in. When USB cable is plugged in and no buttons or anything on the phone is pressed, my laptop attempts to install drivers.
Tried leaving battery out for 30minutes and trying again, but no luck.
Any suggestions?
Cheers!
Stuck in RUU mode?
Kaph said:
Hey guys,
...
Last time it froze, I removed the battery and turned back on, and it got to the "htc" logo and froze. ...
Phone seems completely dead ... When USB cable is plugged in and no buttons or anything on the phone is pressed, my laptop attempts to install drivers.
... Any suggestions?
Cheers!
Click to expand...
Click to collapse
Looks like your phone is stuck in RUU mode.
In RUU mode you see the silver "HTC" logo as long as your phone is connected to your computer with an USB data cable. No charging lights will show in this mode.
You can use the following command to boot your phone to Android:
Code:
fastboot oem boot
When that does not work, because your partition table or system partition might be corrupted, then you would have to use the correct RUU (Rom Update Utility) for your phone to get it back to a working state.
When you have a bricked internal memory chip (emmc) than nothing will work properly to restore your phone to normal working conditions.
In the case you have an engineering HBOOT you could boot a ROM from SD card, but that is a far shot.
Best regards,
Catherall
catherall said:
Looks like your phone is stuck in RUU mode.
In RUU mode you see the silver "HTC" logo as long as your phone is connected to your computer with an USB data cable. No charging lights will show in this mode.
You can use the following command to boot your phone to Android:
Code:
fastboot oem boot
When that does not work, because your partition table or system partition might be corrupted, then you would have to use the correct RUU (Rom Update Utility) for your phone to get it back to a working state.
When you have a bricked internal memory chip (emmc) than nothing will work properly to restore your phone to normal working conditions.
In the case you have an engineering HBOOT you could boot a ROM from SD card, but that is a far shot.
Best regards,
Catherall
Click to expand...
Click to collapse
Thanks for the help
When plugged in with the USB cable -> computer, I still get no response from the phone itself. Screen doesn't turn on, still seems dead. My laptop still says "Installing device driver software" to no avail, and phone is still dead. No lights, screen is off, nada. As though it was powered-off.
ADB Devices lists nothing, and fastboot oem boot hangs on <waiting for device>.
Am I out of luck? I could send the phone off for repair, but as I'm rooted I think warranty is void.
Remarks
Kaph said:
Thanks for the help
My laptop still says "Installing device driver software" to no avail, and phone is still dead
ADB Devices lists nothing, and fastboot oem boot hangs on <waiting for device>.
Am I out of luck? I could send the phone off for repair, but as I'm rooted I think warranty is void.
Click to expand...
Click to collapse
Windows seems to need a driver installation for using fastboot. Did you try to automaticall install device driver software? Have you installed HTC sync on your Windows computer?
When your device does not respond at all, and even refuses to connect in fastboot, then nobody can tell that you have been rooted.
Best regards,
Catherall
Sounds like your EMMC is fried, as of now I don't think there's a solution other than sending it back. Many say HTC accept and fix it even though it is s-off
Sent from my HTC Vision using XDA
did you get this worked out? i had a similar problem, ended up booting into fastboot by holding the trackpad and the power button, then just selected reboot and my phone powered on like nothing had happened, i was running the same rom.
Hey, did you alreasy tourned your phone to the fastboot mode?
Or does your device still have a black screen during boot?
I rooted this phone and when I was done trying S-OFF, phone would not respond to anything. It would only blink the orange notification light when I pressed Power and Vol+, or it would stay steady green with both Vol keys and Power. But the phone screen would never turn on. So after trying for hours to figure it out. I finally took the battery off, plugged the phone held pressed the power button and then put the battery in place the phone finally turned on and it worked. I turned the phone off again and it was doing the same issue. So I did the same step but this time with power and vol- to get in the bootloader and changed the hboot version to Desire Z. After that phone works perfectly, turns on and off with out any issues.
I did have to try the trick a couple of times idk why but it would work once in a while not everytime i tried it. Hope this helps anyone who also ends up with a similar issue.

Dead Lg G3

So I bought a used G3 knowing about the issue it had; it didn't boot. I thought I could find a workaround to this but the phone doesn't boot, doesn't enter recovery or download mode. All the info I have is that when I take off the battery the pc sees it as an unknown device, while it's connected I press the power button for several seconds and it disconnects from the pc, reconnects after several more seconds of pressing the power button. Screen remains dead. Seller told me he had a perfectly working phone before he tried to root it and it never turned on again. One more indication is that the LED notification only flashed red a few times when I connected it to the wall charger and that was it. No LED working after that. I'm open to any suggestions though I guess I'm here for someone to tell me there's no hope reviving the device. Thanks in advance!
Same proble with mine but i bricked mines when update to lollipop and never turn on again . still waiting to some one help to revive my LG
If I come across any solution I'll post it here. In the meantime I've tried the following method on a freshly formatted laptop and I still get "Unknown Device" in Device Manager..
http://forum.xda-developers.com/showthread.php?t=2785089
same here
same problem, someone told me that if was the board or something like that and that it only can be fixed with a complete replacement of this, also, that it could be fixed with linux using comands to install .APK or .TOT.
linux sometimes sees it as Qualcomm CDMA Technologies MSM QHSUSB_BULK, using a virtual machine of linux ubuntu, windows 8.1 sees it as unknow device
LG dead since 3 months ago.................. i wasnt using the phone at all when this happended so........... :crying:
jc.delgado11 said:
same problem, someone told me that if was the board or something like that and that it only can be fixed with a complete replacement of this, also, that it could be fixed with linux using comands to install .APK or .TOT.
linux sometimes sees it as Qualcomm CDMA Technologies MSM QHSUSB_BULK, using a virtual machine of linux ubuntu, windows 8.1 sees it as unknow device
LG dead since 3 months ago.................. i wasnt using the phone at all when this happended so........... :crying:
Click to expand...
Click to collapse
I tried using a boot usb drive to see if ubuntu saw the device but it didn't. Maybe there's some things needed that I didn't do. The thing I don't understand the most is why do windows see it as an unknown device only with the battery out while if I connect the G3 with the battery on, it doesn't show anything on device manager..
Nubrig said:
So I bought a used G3 knowing about the issue it had; it didn't boot. I thought I could find a workaround to this but the phone doesn't boot, doesn't enter recovery or download mode. All the info I have is that when I take off the battery the pc sees it as an unknown device, while it's connected I press the power button for several seconds and it disconnects from the pc, reconnects after several more seconds of pressing the power button. Screen remains dead. Seller told me he had a perfectly working phone before he tried to root it and it never turned on again. One more indication is that the LED notification only flashed red a few times when I connected it to the wall charger and that was it. No LED working after that. I'm open to any suggestions though I guess I'm here for someone to tell me there's no hope reviving the device. Thanks in advance!
Click to expand...
Click to collapse
Hi there.
Please check these 2 threads out and see if any of it will help you. The one for the G2 can also be used for G3.
Here are the links:
http://forum.xda-developers.com/lg-g3/general/unbrick-lg-g3-qhsusbbulk-qualcomm-9008-t3072091 With this technique you would have to find the software online somewhere but this method does revive dead G3 with these symptoms.
http://forum.xda-developers.com/showthread.php?t=2475045
If I helped somehow, hit the THANKS button.
Good luck!
The thing is I can only get the device to be recognized as an Unknown Device in Device Manager and only with its battery out. If I keep 'volume up' pressed nothing happens, it's only shown after I simply connect the USB cable and it pops up after 10 seconds or so. It's very consistent in the way it behaves..
A small update, sometimes when I pull and put the battery again, I connect the phone to a pc while holding down vol- and the pc makes the connected usb sound while the phone led is blinking red for a couple of minutes, then it stops. That's about all there is concerning the phone giving signs of life..

Zenfone 2 does not turn on

Good morning, I have a big problem in my Zenfone 2 and would very much like your help.
Yesterday in the morning he hung up, I thought I had downloaded but I tried to turn it when he called saw the battery was at 50%, I found strange but ok, then the screen locked and the phone started to vibrate and I had to off it. When I called, the battery was at 50%, was saying that the phone was connected and there do not leave sound and saying he was carrying. I thought it might be the rom and turned it on PC to back up and exchange of rom, only the USB no longer recognized the connection to the PC. Was saying that tava carrying, I took the USB and stopped "load" when I called he carried again, just not giving connection to the PC. Anyway I did not back up and changed the rom, he continued the same thing (I was in the AICP (LP) and put the RussiaNBear (LP)).
So I was following a tutorial that I had used before to repair another error (I could not post the tutorial link here, but it's on youtube: (Tutorial - Zenfone 2 unbrick / Restore (ZE551ML / ZE550ML) - In the Droid Will channel)), but I gave soft to do so because the part of the AFT (Asus Flash Tools) it does not recognize the phone, having to disconnect the usb and connect again, and then I screwed me, 'cause the uSB connection was not working. After a few unsuccessful attempts, it seems I agravei even more the situation because now I turn the USB cable pressing volume down and it goes in "Moorefield" and the PC identifies a good, open the xFSTK and can pass the DNX, but when you finish spending DNX the phone should reboot and a screen appears with the symbol of a uSB connection, but that's not what happens. I spend the DNX, the phone restarts and vibrates, there is the xFSTK waiting to pass the OS, but not USB screen appears, the xFSTK does not recognize the phone more in "Moorefield" and I can not do anything else on the device.
I have already connected the phone on another pc, I have changed the cable and nothing. I think it is the mobile usb, if not it would not recognize the first part of xFSTK.
Apologies if I have not posted in the right place, for my English (Google Translate) and the text size, only tried to leave everything well explained so that everyone can understand. Thank you very much, beforehand to help you and I really hope we can solve this problem.
Thank you.
No one ?
no one can help me?

Oneplus 3 just died out of no where

So i was using my phone and decided to restart it after updating my adaway files but my phone never turned back on. The two press the power button screens did not show up either. I tried to uses the MSMdownload tool since i thought my phone was somehow bricked but that didnt work either, it just kept restarting the download process after everything was completed. my computer makes a sound when its connected and it connects correctly as a quallcomm 9008 device but even after all this nothing is working. has anyone experienced something like this or does anyone have any advice?
did you try to long press both power button and vol up ...you should feel a vibration...
maybe it's not turned of maybe it's error causing the screen to be off... also is there any heat?
Which method of the unbrick tool did you use? First or second? If the first, then maybe you should give the second also a try.
Sent from my ONEPLUS A3003 using Tapatalk
I've tried everything and I used th me second method yet nothing happened. I can see my phone get recognized by the computer and get listed on the MSN device list yet nothing happens after it finishes the process. After the green line shows up telling me that it's completed everything the process restarts writhing a few minutes unless I unplug it. No vibration no nothing the phone just died on me after I restarted it .
Try doing MSM on a different PC with all drivers installed , hope it helps
Try to repeat flashing again, there is no other way. Use method 2only. Extract tool again and try flash.
When I was used Xperia Z1, I bricked my phone with a soft brick. So I installed driver in my PC and flash Kernel though FASTBOOT(ADB) either it's not show Device in my PC (I show just "Unknown Device").
After that my phone can connect to my PC again (Now It shown C9303 or something that meant it know it's a phone).
So I can flash by Flashtools again. Soft brick is not scary as Hard brick, you'll find some way to bring it back easily.
Hope this help!
PS. Bricked Phone is WEAK in Battery, always connect it with charger.

Categories

Resources