Oneplus 3 just died out of no where - OnePlus 3 Questions & Answers

So i was using my phone and decided to restart it after updating my adaway files but my phone never turned back on. The two press the power button screens did not show up either. I tried to uses the MSMdownload tool since i thought my phone was somehow bricked but that didnt work either, it just kept restarting the download process after everything was completed. my computer makes a sound when its connected and it connects correctly as a quallcomm 9008 device but even after all this nothing is working. has anyone experienced something like this or does anyone have any advice?

did you try to long press both power button and vol up ...you should feel a vibration...
maybe it's not turned of maybe it's error causing the screen to be off... also is there any heat?

Which method of the unbrick tool did you use? First or second? If the first, then maybe you should give the second also a try.
Sent from my ONEPLUS A3003 using Tapatalk

I've tried everything and I used th me second method yet nothing happened. I can see my phone get recognized by the computer and get listed on the MSN device list yet nothing happens after it finishes the process. After the green line shows up telling me that it's completed everything the process restarts writhing a few minutes unless I unplug it. No vibration no nothing the phone just died on me after I restarted it .

Try doing MSM on a different PC with all drivers installed , hope it helps

Try to repeat flashing again, there is no other way. Use method 2only. Extract tool again and try flash.

When I was used Xperia Z1, I bricked my phone with a soft brick. So I installed driver in my PC and flash Kernel though FASTBOOT(ADB) either it's not show Device in my PC (I show just "Unknown Device").
After that my phone can connect to my PC again (Now It shown C9303 or something that meant it know it's a phone).
So I can flash by Flashtools again. Soft brick is not scary as Hard brick, you'll find some way to bring it back easily.
Hope this help!
PS. Bricked Phone is WEAK in Battery, always connect it with charger.

Related

Dead Lg G3

So I bought a used G3 knowing about the issue it had; it didn't boot. I thought I could find a workaround to this but the phone doesn't boot, doesn't enter recovery or download mode. All the info I have is that when I take off the battery the pc sees it as an unknown device, while it's connected I press the power button for several seconds and it disconnects from the pc, reconnects after several more seconds of pressing the power button. Screen remains dead. Seller told me he had a perfectly working phone before he tried to root it and it never turned on again. One more indication is that the LED notification only flashed red a few times when I connected it to the wall charger and that was it. No LED working after that. I'm open to any suggestions though I guess I'm here for someone to tell me there's no hope reviving the device. Thanks in advance!
Same proble with mine but i bricked mines when update to lollipop and never turn on again . still waiting to some one help to revive my LG
If I come across any solution I'll post it here. In the meantime I've tried the following method on a freshly formatted laptop and I still get "Unknown Device" in Device Manager..
http://forum.xda-developers.com/showthread.php?t=2785089
same here
same problem, someone told me that if was the board or something like that and that it only can be fixed with a complete replacement of this, also, that it could be fixed with linux using comands to install .APK or .TOT.
linux sometimes sees it as Qualcomm CDMA Technologies MSM QHSUSB_BULK, using a virtual machine of linux ubuntu, windows 8.1 sees it as unknow device
LG dead since 3 months ago.................. i wasnt using the phone at all when this happended so........... :crying:
jc.delgado11 said:
same problem, someone told me that if was the board or something like that and that it only can be fixed with a complete replacement of this, also, that it could be fixed with linux using comands to install .APK or .TOT.
linux sometimes sees it as Qualcomm CDMA Technologies MSM QHSUSB_BULK, using a virtual machine of linux ubuntu, windows 8.1 sees it as unknow device
LG dead since 3 months ago.................. i wasnt using the phone at all when this happended so........... :crying:
Click to expand...
Click to collapse
I tried using a boot usb drive to see if ubuntu saw the device but it didn't. Maybe there's some things needed that I didn't do. The thing I don't understand the most is why do windows see it as an unknown device only with the battery out while if I connect the G3 with the battery on, it doesn't show anything on device manager..
Nubrig said:
So I bought a used G3 knowing about the issue it had; it didn't boot. I thought I could find a workaround to this but the phone doesn't boot, doesn't enter recovery or download mode. All the info I have is that when I take off the battery the pc sees it as an unknown device, while it's connected I press the power button for several seconds and it disconnects from the pc, reconnects after several more seconds of pressing the power button. Screen remains dead. Seller told me he had a perfectly working phone before he tried to root it and it never turned on again. One more indication is that the LED notification only flashed red a few times when I connected it to the wall charger and that was it. No LED working after that. I'm open to any suggestions though I guess I'm here for someone to tell me there's no hope reviving the device. Thanks in advance!
Click to expand...
Click to collapse
Hi there.
Please check these 2 threads out and see if any of it will help you. The one for the G2 can also be used for G3.
Here are the links:
http://forum.xda-developers.com/lg-g3/general/unbrick-lg-g3-qhsusbbulk-qualcomm-9008-t3072091 With this technique you would have to find the software online somewhere but this method does revive dead G3 with these symptoms.
http://forum.xda-developers.com/showthread.php?t=2475045
If I helped somehow, hit the THANKS button.
Good luck!
The thing is I can only get the device to be recognized as an Unknown Device in Device Manager and only with its battery out. If I keep 'volume up' pressed nothing happens, it's only shown after I simply connect the USB cable and it pops up after 10 seconds or so. It's very consistent in the way it behaves..
A small update, sometimes when I pull and put the battery again, I connect the phone to a pc while holding down vol- and the pc makes the connected usb sound while the phone led is blinking red for a couple of minutes, then it stops. That's about all there is concerning the phone giving signs of life..

Zenfone 2 does not turn on

Good morning, I have a big problem in my Zenfone 2 and would very much like your help.
Yesterday in the morning he hung up, I thought I had downloaded but I tried to turn it when he called saw the battery was at 50%, I found strange but ok, then the screen locked and the phone started to vibrate and I had to off it. When I called, the battery was at 50%, was saying that the phone was connected and there do not leave sound and saying he was carrying. I thought it might be the rom and turned it on PC to back up and exchange of rom, only the USB no longer recognized the connection to the PC. Was saying that tava carrying, I took the USB and stopped "load" when I called he carried again, just not giving connection to the PC. Anyway I did not back up and changed the rom, he continued the same thing (I was in the AICP (LP) and put the RussiaNBear (LP)).
So I was following a tutorial that I had used before to repair another error (I could not post the tutorial link here, but it's on youtube: (Tutorial - Zenfone 2 unbrick / Restore (ZE551ML / ZE550ML) - In the Droid Will channel)), but I gave soft to do so because the part of the AFT (Asus Flash Tools) it does not recognize the phone, having to disconnect the usb and connect again, and then I screwed me, 'cause the uSB connection was not working. After a few unsuccessful attempts, it seems I agravei even more the situation because now I turn the USB cable pressing volume down and it goes in "Moorefield" and the PC identifies a good, open the xFSTK and can pass the DNX, but when you finish spending DNX the phone should reboot and a screen appears with the symbol of a uSB connection, but that's not what happens. I spend the DNX, the phone restarts and vibrates, there is the xFSTK waiting to pass the OS, but not USB screen appears, the xFSTK does not recognize the phone more in "Moorefield" and I can not do anything else on the device.
I have already connected the phone on another pc, I have changed the cable and nothing. I think it is the mobile usb, if not it would not recognize the first part of xFSTK.
Apologies if I have not posted in the right place, for my English (Google Translate) and the text size, only tried to leave everything well explained so that everyone can understand. Thank you very much, beforehand to help you and I really hope we can solve this problem.
Thank you.
No one ?
no one can help me?

[qhsusb_bulk] Super Bricked Nexus 5X?

So, the other day my phone started acting weird. It randomly restarted, then worked another hour or so, and then started shutting down almost immediately after booting. I was running a Nexus 5X with rooted stock Android 7.0.0 (SuperSU root) and ElementalX kernel. It had been running this for a few months without any issues. I can't think of anything I did to trigger this. I didn't run any updates, I haven't flashed anything since I installed ElementalX couple months ago.
After a lot of troubleshooting (at first I could still get into the bootloader and recovery, but when I did, TWRP didn't recognize any partitions? I was unable to access the file system in TWRP), it finally got so bad that my phone is no longer recognized by my laptop other than "QHSUSB_BULK" device in the Device Manager (Windows 10 x64). Completely black screen, no response, no LED when plugging in adapter. One time I managed to get into the bootloader (randomly, no idea what triggered it) and I managed to put stock 7.1.1 on it, but soon after the installation of that, the exact same thing happened: random reboots, progressively getting worse to in the end: no recovery, no bootloader, only recognized as "QHSUSB_BULK". So I was back to the lowest point.
I read about a "hidden second bootloader" on the 5X, that would be accessable through Power+Both Volume keys, but that doesn't work at all for me (tried it for up to 1 minute of pressing).
After hours of searching (I probably read all the 5X + other phones's topics here that have this issue..), I came here: www.droidsavvy.com/unbrick-qualcomm-mobiles/
I followed those steps precisely, got my laptop to recognize the phone as 'Qualcomm HS-USB QDLoader 9008' by installing the Qualcomm drivers with driver signature verification turned off, but I just couldn't get the QFIL program to flash anything to my phone. It threw a "Download Fail:Sahara FailSahara Fail" saying it couldn't send the Flashing program to my phone. I tried several things here: attempted to power off the phone, then hold Volume up+plug in USB --> flash straight away, different driver/software versions, different laptop, but all to no avail.
I have no real way of telling whether the phone is on or off (it seems impossible to actually turn it off - if I hold power for 30 or so secs I do hear the USB disconnect-connect sound from my laptop, but the device is still shown as "QHSUSB_BULK" so it won't actually turn off properly).
My current hypothesis: it's a hardware fault (eMMC?) and as I'm still within warranty I can send it in for repair/replacement.
Perhaps there is a very slight chance that someone has also encountered this, and it's still a software problem which can be helped by me in some way?
Thanks in advance!
Its probably some part of the motherboard that is faulty. Take it into a repair center. Get it replaced.

How to "debrick/unbrick"an oppo find 7/7a

Greetings,im Akmal and today I will be sharing some helpful solution to unbrick your Oppo Find 7/7A.​Short Story(myb a lil bit longer)¬
So my find 7A got soft bricked when I install custom rom without using TWRP(pretty stupid to do so)
After rebooting my phone keeps on booting to fastboot mode and no matter it happen the same if i press vol up/vol down and power button.
At this stage I knew my phone is soft bricked.So I found the solution to it through some old posts which you have to extract the ColorOS blablabla and adb thingy(I dont wanna go through it here)
But I dont realised that i forget to flash a file name "TZ.MBN"
Now that my phone wont ever boot or even to fastboot which resulted to hard brick.
No recovery screen.
No Charging status screen
No Fastboot screen
No sign of vibrating when i push the power button
-So here is the solution-
Disclaimer-I am not responsible for what ever happen to your device after this-
-there are already some other posts like this but I make this post to let you know that its still working.
1a)First,download the OPPO UNBRICK TOOL HERE
bit.ly/OPPOUNBRICK
1b)goto Google and search for Qualcomm qd loader.download,install and restart your pc.
2)After restarting,Extract the file from OPPO UNBRICK TOOL and open "Msm8974DownloadTool.exe"
3)as you may have notice,its chinese language or some aliens language but dont worry it isn't corrupted,just follow through↓
4)disconnect your device battery,then open the software and press start,after that connect the phone to your pc/laptop (WITHOUT BATTERY) and hold volume up button
5)please wait patiently as it is reflashing stock rom to your device.
6)as you may have noticed maybe your device disconnected but DONT GET PANICKED! press again the power button until its downloading again on the software.
7)If it has done downloading,some row should be in a Green colour.
8)disconnect your cable and try turning on your device again.
That's it!Any comment or curiosity I will try helping you through the comment section but I not guaranteed everything I can answer
P/S:if your device is softbricked,you just should disconnect your battery,and then open the software and press start,then connect the phone to your pc/laptop (WITHOUT BATTERY) and hold volume up button.
If your device is hard bricked(like mine)only holding the power button could work as well
*UPDATE* 24/2/2019
-If you guys still have any concerns kindly contact me through twitter (0728mal)
*UPDATE* 4/7/2020
-yes it is still working guys,no worries kayy
-no you don't need internet for it to work,the software already has all the files needed to flash the device,which is why the file is pretty big.
best regards,
Akmal

			
				
Link updated :good:
akmlfhm said:
Greetings,im Akmal and today I will be sharing some helpful solution to unbrick your Oppo Find 7/7A.​Short Story(myb a lil bit longer)¬
So my find 7A got soft bricked when I install custom rom without using TWRP(pretty stupid to do so)
After rebooting my phone keeps on booting to fastboot mode and no matter it happen the same if i press vol up/vol down and power button.
At this stage I knew my phone is soft bricked.So I found the solution to it through some old posts which you have to extract the ColorOS blablabla and adb thingy(I dont wanna go through it here)
But I dont realised that i forget to flash a file name "TZ.MBN"
Now that my phone wont ever boot or even to fastboot which resulted to hard brick.
No recovery screen.
No Charging status screen
No Fastboot screen
No sign of vibrating when i push the power button
-So here is the solution which make my phone came to life again-
Disclaimer-I am not responsible for what ever happen to your device after this-
-there are already some other posts like this but I make this post to let you know that its still working.
-make sure to charge the phone first even if you do not know if it charging or not
1)First,download the OPPO UNBRICK TOOL HERE
bit.ly/OPPOUNBRICK
2)Extract the file and open "Msm8974DownloadTool.exe"
3)as you may have notice,its chinese language or some aliens language but dont worry its not corrupted,just follow through
4)Connect your phone to PC and press the power button until you heard some like mounted usb alert on windows.(its ok aslong windows does not detect it on device manager but its ok if you can hear the alert sound.
5)back to the software,no need to mess around with it.Click on start until its downloading a "new life" to your phone.
6)as you may have noticed maybe your device disconnected but DONT GET PANICKED! press again the power button until its downloading again on the software.
7)If it has done downloading,some row should be in a Green colour.
8)disconnect your cable and try to turning on your device again.
That's it!Any comment or curiosity I will try helping you through the comment section but I not guaranteed everything I can answer
best regards,
Akmal
Click to expand...
Click to collapse
hi im having this problem as well. my find 7a is hard bricked after i flash coloros v2.1.5i without twrp. the problem is, my computer does not detect my phone at all even after i hard reset and hold power button for 30 seconds. i dont think the battery is drained because before this happened, my phones battery was about 90% and i try recharging the phone for 30 minutes, and nothing happened. so the debrick tool cannot be used. can you suggest anything for my problem?
Got excited when I read this post! Is there an Oppo Unbrick tool for Mac? I don't have a Windows machine so I can't run the .exe file... Is there an equivalent for those of us not on Windows? Thank you
Shadician said:
Got excited when I read this post! Is there an Oppo Unbrick tool for Mac? I don't have a Windows machine so I can't run the .exe file... Is there an equivalent for those of us not on Windows? Thank you
Click to expand...
Click to collapse
On Mac's OS, you can always install Windows on its proprietary virtual machine and get the process going that way.
babyenchantress said:
hi im having this problem as well. my find 7a is hard bricked after i flash coloros v2.1.5i without twrp. the problem is, my computer does not detect my phone at all even after i hard reset and hold power button for 30 seconds. i dont think the battery is drained because before this happened, my phones battery was about 90% and i try recharging the phone for 30 minutes, and nothing happened. so the debrick tool cannot be used. can you suggest anything for my problem?
Click to expand...
Click to collapse
hello there!I'm really sorry for not checking this that often and really sorry if i let you down because im too busy with my schools work
btw before my computer can detect my phone i have to download a driver which detect qualcomm processor for my oppo then it can be detected by my pc therefore i can do the unbrick process:good:
Shadician said:
Got excited when I read this post! Is there an Oppo Unbrick tool for Mac? I don't have a Windows machine so I can't run the .exe file... Is there an equivalent for those of us not on Windows? Thank you
Click to expand...
Click to collapse
yeah you can try WINE also but i never have any experience with mac os before so i cant guarantee that it will work considering that you're configuring your drivers,which can go wrong if not done correctly
So I have bricked my phone (X9006) while trying to install TWRP recovery. It is stuck on logo and adb/ fastboot does not recognise it anymore. I have tried the above-mentioned tool, but this program also does not do anything for a long time. Am I missing something in applying this solution?
Edit: I am an Windows 10 and I might not have the Qualcomm drivers installed. I don't know how to install
true_friend2004 said:
So I have bricked my phone (X9006) while trying to install TWRP recovery. It is stuck on logo and adb/ fastboot does not recognise it anymore. I have tried the above-mentioned tool, but this program also does not do anything for a long time. Am I missing something in applying this solution?
Edit: I am an Windows 10 and I might not have the Qualcomm drivers installed. I don't know how to install
Click to expand...
Click to collapse
Hello there.have you tried downloading the "Qualcomm"
Driver software on your PC?
is it necessary to remove the battery? I don't have tools for opening my phone and it's battery is non-removable
Perhaps an important step is missing. The Qualcomm qd loader driver is may not signed. I had to boot into the extended start menu on Windows 10 and disable the driver signature check - point 7 - and could now successfully debrick my find7.

Oneplus 5t black screen unbricktool doesnt seem to work

I've got a dead oneplus 5t from my son. It was not charging anymore.. So I've replaced charging cable and battery.. Seemed to work it was charging... However it doesn't boot... No logo screen screen stays black/blank.
Tried several suggestions on this forum to get into recovery mode, fastboot mode... But still nothing. Only vibrating works after a few seconds.
So tried to unbrick with OP5T_Unbrick_tool_dumpling_43_J.40_181105(OOS.5.1.7) and the qualcomdrivers..
I was able to install the drivers and I see they are installed in devicemanagement.. and an empty folder create for oneplus.
I charged the phone all night and was able to download the upgrade. It then says download complete and I tried to restart the phone..
Still just vibrating but nothing happens.. Seems like everything has vanished from the phone, no recovery, no bootloader, no files.
So how to proceed to get all the stuff on the phone? And maybe the displayscreen is dead, but how can I tell?
Also tried the SMT upgrade. Strange thing is the device and com port are seen in devicemanagement and active when I connect without volume up, but cannot start because it says When I try to use smt mode the program says: "This COM port is disable by user". With volume button up pressed and then connect, ledlight turns green but the qualcomdevice is grayed out in devicemanagement and it says waiting for device..
Any help is welcome. I am a noob in how to proceed on the phone however I have an IT background.
Spent already so many time figuring out .. maybe it's effortless and its for the trashbin.
Thanks in advance
SOLVED
I opened the phone again loosened all those tiny connections to battery, screen,charger, mainboard and re-attached them.. Somehow a connection seemed to be fitting allright as yI looked at it, but apparently wasn't :good:

Categories

Resources