Upgrade ROM code error - Touch Diamond, MDA Compact IV ROM Development

I have flashed many Custome ROM's before. I have HardSPL installed on my phone.
I tried flashing to a ROM (I forget which one now, I think Cloudfa or something) and it stopped at about 15%. The Update utility stopped as well.
I cannot connect to bootloader at all. I tried holding down on Volume down/Reset to enter bootloader, but the thing is that it's already in bootloader with the message "Upgrade ROM code error, Please try again"
ActiveSync doesn't see my phone either. In fact all it does is just sit on the bootloader screen with that error...
Please Help... Thanks You...

A normal soft reset still brings you back to Bootloader?
What happens when you plug in your device? Does it not change from serial to USB at the bottom?

band27 said:
A normal soft reset still brings you back to Bootloader?
What happens when you plug in your device? Does it not change from serial to USB at the bottom?
Click to expand...
Click to collapse
Sorry. Yes it does show USB when plugged in, but won't respond to anything that I have tried software wise. It does not switch from this bootloader/error screen at any point. Even after I pull my battery and turn it back on...
I have yet to come across a thread which has this exact problem...

jzalapski said:
Sorry. Yes it does show USB when plugged in, but won't respond to anything that I have tried software wise. It does not switch from this bootloader/error screen at any point. Even after I pull my battery and turn it back on...
I have yet to come across a thread which has this exact problem...
Click to expand...
Click to collapse
Have you tried flashing a different ROM while in bootloader?

^^ Yes. It give me an error on my computer...
I would like to try the internal flashing method but I don't seem to have a way of getting at my Storage Card.
I found this thread with a similar problem
http://forum.xda-developers.com/showthread.php?t=480022
I WAS just able to get off of that screen I was talking about, but the best I get is to the Touch Diamond Screen that lists my ROM and such. So no real progress.
I have a feeling that I would resolve my problem if I could Flash from the Interanl Storage...

Have you tried hard resetting the device?
Pull out stylus and Holding....1) Vol. Down 2) Center Round button 3) then press red button aka soft reset with stylus

Nothing...

im stuck
hi all i am very new to this im not sure what i have done or how to fix the problem i download these this morning and they worked
rom version 1.57.831.1(47324)wwe
radio version 1.14.25.24
protocol version 52.64.25.34u
when i bootload in tri colours screen it shows
BLAC100 32M
SPL-1.56.OliNex
MicroP-Blackstone (led)v6
if it shows that i must of done something right i think of what ill read
and i have windows 7 ulitmate and i have Miri_WM65_21815_V19.0_Premium
when i double click on the BLACKSTONE RUU WRAPPER it crashes then i rename a new folder and done it from there and it works but it comes up wit error 208 file open? then i got told to rename to ruu_signed.nbh file to blacimg.nbh and to store it in the root of my sd card done that then somehow i got it to come up to the screen by Turn off the phone, press and keep pressed volume down button and while keeping it pressed turn on the phone then i see a message "Press power to flash your device" and i press power to flash got to 0% and it crashed and come up with Upgrade ROM code error plz try again and stuck in bootloader mode but now it wont even turn on its dead it wont turn on no matter what i do can someone plz help
all i want to do is get windows mobile 6.5 working i cant understand that it can be so hard to do
thanxs blueboys25!

Related

HELP!!!!

:?
I tried to make an update with the file JASJAR_WWE_11353_137_10301
Suddenly the Display stop et 99% of the extended Rom Update and on my monitor was an infomation like "an error happend"
After this, nothing else happend .
Yes, realy nothing happens anymore. I cant start the device not with power, not with reset or with power+reset
nothing nothing nothing
What can i do
If i start to try a new update, it schows me no information about what rom etc. is installed or what will be installed. if i then start i get the notice, that it is the wrong device.
Help me please. ist there any way to put the mda back to live?????
I guess i dont only need an update but the complete software
HELP!!!
I have the exact same issue after the upgrade. Nothing will happen. I spent several hours trying resets, combination of button pressed, removed battery, resets, just to try to get back the boot loader mode but nothing is happening.
there has to be a way to do this and I hope someone on this board had that issue before and got it resolved.
I had a similair issue with my old XDA II, it turned out my storage card was corrupted. Use a card reader to check your storage card is OK, perhaps format the storage card (having saved any data first of course) and see how you fare
Have had the same problem wirh a radio ROM update on my QTEK9000. The anly thin that still worked was the hard reset. After the hard reset the device still did not respond. But when i connected it to the PC I could start the updateprocess of the original ROM. I took about 20 minutes for the whole procedure and than the Qtek9000 was back in factory default (Pffff and I could breath again).
So perhaps you can try a hard rest and then connect aganin to the PC.
I allready tried this!
But nothing happens.
Even if i put the power device or the usb into the mda, no LED schows anything. just sometimes the LED is red for not more than a minute. if it then goes out, i get the message "Unknown usb device" in my PC
Are you in bootloeader mode? Do you see the words USB or Serial on the screen of the Universal in Portrait mode. Note: Backlight is off so you have too look real hard, but it should be there
no, i see nothing.
I had quite a hard time yesterday while upgrading. The bootloader is very hard to see, use a torch to lite up your display. In portrait view on the top should be the word serial or usb, on the bottom v1.00.
I also did a hard-reset in this stage, but it just returned to the bootloader menue.
If I connect to the PC and the device is recognized I see the word serial in the display change to USB. For me I do not know the reason but my PC did not want to fulfill the upgrade process. Needed to take another PC (Laptop) to solve the problem. After the upgrade of the ROM, You still need to upgrade the Radio (this was my experience) before a cold-reset will put You back to business.
Good luck.
Ruud
Having the exact same problem as gary_b and having performed quite a few upgrades, I can confirm there is absolutlely nothing on the screen. The unit will not go into bootloader mode or even able to do a hard reset. It is not recognized when plugged in the USB.
When connected to power and the hard reset procedure is done, the red charging light will come up for less than 1/2 seconds and disappear.
I tried all different combination to make it boot but nothing. If I could at least get it to bootloader more, I can revive it.
Feel very bad I cannot help here.
I was wondering Yesterday about one thing. IF, during all this upgrading process, the battery runs out, (as it does not seem to charge during upgrade process) will it show bootloader screen ?
Would it be possible to get a loaded battery from somebody to check yours ?
That is a good suggestion to try out, but I have been unable to find anyone that has that device. It might be simply a drained battery.
Mine got corrupted I think at the end of the upgrade right after I did a regular reset instead of teh power and reset procedure.
However, I would think that even with no battery in, the unit should power back up when plugged in no?
Maybe an idea for somebody who is doing upgrading now, and is in bootloader status anyway.
Take out the battery, but connect with USB to PC with ASync. Does the bootloader state show ?
I am sorry to not do it for myself, if You saw my desperate state Yesterday, You will believe that I am not willing to see that bootloader screen for some time, sorry.
Ruud
now i know what to do:
Nothing!!
I went to a service-point with my mda pro and there was nothing to do with it.
If this happens the complete memory is "killed". Like "format c:" and while format is running you switch out the power.
Thanks god: I got a new MDA pro because i did not tell them (in the store)that i tried an update!
But i called the service-line before anf they told me that there is nothing to do!
But thx
Wow, can't say that this is good informatuin for those with this problem, but very glad it worked out for You.
I ve had this problem 5 minutes ago. Finally a took out the battery. Then connect to AC and Red led is on. Then i put the battery, tried hard reset and message to confirm hard reset in the screen (wellcome to life, jasjar).Then i run radio update again and it's upgrading rigth now....buffffff
I almost suffered a heart attack when this happened an hour ago. Have found that the update works fine if the SD card is taken out... phew.

sprint touch not booting any screen ...help

while doing the gps upgrade, I was doing step 4 (Run the Alltel ROM exe file ) it failed at 8% then sent me to a recovery page after i removed the battery my touch wont do anything ,i tried soft reset ,camera and even hard .the only time i see anything is when i plug a usb cable in ,just a red light in the speaker hole.
try getting it to bootloader (hold power button, camera button and soft reset button) it should display a tricolor screen. now just plug in the usb cable and reflash the same rom or a different one
tried that it didn't work
What is the bootloader version you are using? 0.4 or 2.31
If you see 2.31.CoKE, you should be fine, but read more, more, more!!!
Don't want to sound like I'm not helping, but I am no expert right now, so don't want to further cause damage to your phone.
So go here:
http://forum.ppcgeeks.com/showthread.php?t=24979
i'm having a somewhat related problem..
I rom updated.. phone works but get a USB not recognized error when i plug it into any xp box.
I guess i need to try an activesync cab file..
if that doesn't work.. i'll reflash a rom through SD method once i find out how.
Anyone got a link for that?

Can't get to bootloader!

When ever I try to get to bootloader mode, my phone just comes up to the tri-color screen. I press and hold the left OK key along with the power button, then do a soft reset. I only get to the tri-color screen. Can someone help me out with this please...I'm trying to upgrade to a WM6.1 rom on my 8525 via SD card.
1jaxstate1 said:
When ever I try to get to bootloader mode, my phone just comes up to the tri-color screen.
Click to expand...
Click to collapse
the tri-color screen is the bootloader. (read the wiki)
wfg
starbase64
1jaxstate1 said:
When ever I try to get to bootloader mode, my phone just comes up to the tri-color screen. I press and hold the left OK key along with the power button, then do a soft reset. I only get to the tri-color screen. Can someone help me out with this please...I'm trying to upgrade to a WM6.1 rom on my 8525 via SD card.
Click to expand...
Click to collapse
The tri-color screen IS the bootloader. I have found with my 8525, that if you turn the device off (power button for 5 seconds, then tap OK), all you need do is hold the side OK and the power button together for a few seconds. No need to find the reset hole if the device is OFF.
If you have an SD card in the device (with a copy of HERMIMG.NBH on it), the Tri-Color screen will come up, searching the card. When the NBH file has been found, it will show you the various parts that the file includes, and prompt you to press the power button to begin.
It's really easy this way. I rarely flash through USB anymore.
Hope this helps,
-pvs
Wow..thanks for the speedy response. I'll give it a try. Thanks again.
When I try to upgrade via SD, the bootloader never reads the SD card, it just sits...and says serial at the bottom of the screen.
When I try to upgrade via USB, after I start the RUU, the active sync connection is broken, and the phone goes into the bootloader screen and just sits...and says USB at the bottom of the screen.
If anyone has had this problem, please let me know. If not..I guess I'll just have to go out and buy a Tilt.
Current ROM: 2.15.502.3
Current Radio: 1.40.30.00
SUCCESS!!!!
Thanks for your help. My company has the firewall on and it, for some reason was killing my active sync connection. I was able to upgrade via USB. And this ROM is looking great starbase64
1jaxstate1 said:
When I try to upgrade via SD, the bootloader never reads the SD card, it just sits...and says serial at the bottom of the screen.
Click to expand...
Click to collapse
1) Is your SD card freshly formatted (FAT32)?
2) have you installed HardSPL? If not, do it.
3) Are you sure you spelled the name of the NBH correctly? HERMIMG.NBH
4) Copy HERMIMG.NBH to the root of your SD card
5) Shut off the device (power off all the way)
6) Insert the SD card with only the one file (HERMIMG.NBH) on it
7) Press the side OK button and the power button simultaneously for a couple of seconds
8) your device should start up, and the bootloader will look for the HERMIMG.NBH file
9) If all the above is done corectly, your device SHOULD find the NBH and tell you what parts it contains, then ask you if you wish to proceed, by pressing the power key. If this isn't happening for you, I'm afraid I don't have any other suggestions for you.
1jaxstate1 said:
When I try to upgrade via USB, after I start the RUU, the active sync connection is broken, and the phone goes into the bootloader screen and just sits...and says USB at the bottom of the screen.
If anyone has had this problem, please let me know.
Click to expand...
Click to collapse
Others HAVE had this problem. You need to disable one of the settings in ActiveSync, but I don't remember which one. Try doing a search under the main HERMES forum, including all subforums. This is one of those questions that gets asked a lot, so be prepared to sift through all the repetitive threads (GOD, if only people would SEARCH first!).
1jaxstate1 said:
If not..I guess I'll just have to go out and buy a Tilt.
Click to expand...
Click to collapse
You might want to read THIS, first
Good luck,
-pvs
when you say copy the .nbh file to the root of the SD card what exactly do you mean. When i put the SD card in there and format it its completely empty with nothing there, then the only option i have is open the SD card folder and put it in there, is that correct?
okay so i just did the SD card flashing, said on the screen it was flashing and did the whole thing fine. Told me it was complete so i pressed the power the button to restart the phone and no matter how many times i restart the phone it just boots into Tri color screen and says serial at the bottom.
I tried soft reset and removing the battery no matter how many times i do it, always comes back to Tri color screen.. help!
ahhhhwhoa said:
okay so i just did the SD card flashing, said on the screen it was flashing and did the whole thing fine. Told me it was complete so i pressed the power the button to restart the phone and no matter how many times i restart the phone it just boots into Tri color screen and says serial at the bottom.
I tried soft reset and removing the battery no matter how many times i do it, always comes back to Tri color screen.. help!
Click to expand...
Click to collapse
Hmmm, I typically do a RESET after the flash process completes. Never tried shutting down using the power button. So now your device is stuck in BL? I'm not sure of the procedures you need to try to escape that one, but I KNOW it's been discussed here in the forums. You MIGHT try flashing a different ROM. It might be the simplest way to recover. If that doesn't work, you might want to check the Wiki HERE.
Good luck!
-pvs

[Q] bricked tilt 2

help please!
i preformed task 29 on my tilt 2 and i now have an ATT screen and wont go any further. when i try to stat it it only goes as far as the first screen and no further. i tried resting it to no avail. i can not establish connection with pc. i have vista for pc. can somebody help please?
Yes. now u preformed that, you want to plug in your USB. Push reset and the lower volum button at the same time. You will go into boot loader mode. It should say USB on the bottom once u have made a connection after connecting your USB to the computer. At that point flash your Radio, after flashing your radio, flash your rom. All like you normaly would ..
PS. make sure Sim and MScard is out of phone before preforming Flashing Radio, then the rom. Then replace the sim card after all the installation from the rom you are installing..
First go back to the task 29 post and read all the instructions.
Task 29 is a memory wiper,it completely wipes the memory of the device leaving only the radio and basic functions.
To get up and running again follow these instructions:
1. Download the newest stock rom for ATT found in the Rom Development forum. http://forum.xda-developers.com/showthread.php?t=737168
2. Remove back cover from the device, remove the battery, remove the SIM card and remove the SD card if you have one. Reinstall the battery, do not replace the back cover.
3. Power up the device and connect it to the PC. Press the down volume button and press and hold the stylus into the reset button, hold both until the boot screen appears. Windows may install some software at this time, let the software install.
4. When USB appears at the bottom of the boot screen run the ROM installer software run. Follow ALL on screen instructions.
NOTE: If you have Hard SPL installed you can install any custom ROM, if not you MUST install a STOCK SHIPPED ROM.
twh said:
help please!
i preformed task 29 on my tilt 2 and i now have an ATT screen and wont go any further. when i try to stat it it only goes as far as the first screen and no further. i tried resting it to no avail. i can not establish connection with pc. i have vista for pc. can somebody help please?
Click to expand...
Click to collapse
First of all check to see if your phone is hardspl'ed by turning phone completely off then hold volume down key then power phone back on from here you should be on tri-color screen see what the spl version says if it says 0.85Olinex it's hardspl'ed anything else is not hardspl'ed.
If your phone is hardspl'ed then your good all task29 does is wipe your entire os off your phone thats why it won't boot to nothing but the startup screen so in order for it to boot you need to flash a rom on to it, so like before power phone off hold volume down key & power phone on you should be on tri-color screen again at the bottom of phone screen it should say serial now plug in usb from computer now it should say usb at the bottom of phone find a rom that you like then flash it phone should reboot after flash & work like normal once again.
Hope this helps
thank you all you guys. you all were awesome. as you could imagine, i am new to wm. but with the help of every body, i got my phone up and running.
twh said:
thank you all you guys. you all were awesome. as you could imagine, i am new to wm. but with the help of every body, i got my phone up and running.
Click to expand...
Click to collapse
no problem i'm glad we all were able to help you

[Q] Bootloader nightmare

I have a nordic HTC Touch Pro 2
This unit started acting up after I installed the Energy ROM from the 20th of December. It used to fail in booting occationally(fixed by attaching USB-power), but now it is thouroughly stuck in the bootloader.
This is what I see when I reboot:
RHOD100 32M SS-BC
SPL-0.85.OliNex
MicroP(LED) 0x0A
MicroLED(KEY) 0x04
TURBO HW/TURBO SW
TP MFG DATA
509,521 792,844
795,200 221,198
226,843 Calibrated
Serial (changes to USB when connected)
There is a quick flash of 2 previous screens, one tri-color and one saying something about no image to load.
I belive, but would be thrilled to be proven wrong, that I have tried all tricks.
Running Windows 7 I first disabled device driver signing and loaded the HTC USB driver. Downloaded mtty 1.42, connected to the phone via USB and ran "boot" command.
The only problem listed was one bad block in CE.
Tried reboot again with same error.
"info 8" revealed that the bad block is 370.
Ran "task 29" but it gave an error trying to delete block 370.
Rebooted and tried to flash latest 29007 Energy ROM. No errors reported during the flash, still when it rebooted after reaching 100% it stopped in bootloader again.
I have also tried this procedure and replaced the Energy ROM with the latest original nordic ROM. When I use "boot" command from mtty I get the HTC screen (white background with htc in green letters) but the phone apparantly is stuck there. A soft restart brings me bach to the bootloader again.
Is my phone bricked? I'm not sure what to do or try next and as I have seen others report my battery is draining and will not charge(no light) when plugged in to computer or charger.
Thanks in advance, I love what you all do for this community and wouldn't have still used tha TP2 if it wasn't for all the great ROMs presented here!
NVM, re-read and see you already tried my suggestion.
Additional info
I ahould add that I also can't do a hard reset. Pressing and holding send and end and then power button only result in getting the bootloader menu. I borrowed a freshly charged battery and tried loading a new ROM, but no change, it still only restarts to the bootloader after completion.
If you can get into bootloader and the usb shows when plugged in, you should be able to flash back to stock via RUU.
Try this;
Open your downloaded ROM with unzipper. You should see two files, the RUU and the RHODIMG.nbh. Copy the .nbh onto the root of your SD card. Powerup the device holding the volume down. It should boot to bootloader and immediatly look for and find the .nhb and install it.
Hope that helps.
Hi!
Thanks for your answers! Sorry about the late reply!
I tested with RHODIMG.nbh file(29007 Energy) on the SD-card. The installation started and ran as expected. When done the screen showed the following info:
"RHODIMG.nbh - OK
OS - OK
Update Complete
UPDATE SUCCESS"
There were no button to press on the screen, and pressing the power-button didn't do anything. I eventually removed the battery, reinstalled the battery and pressed the power button. Unfortunately for me I was once again presented with the bootloader screen.
Any ideas to a new approach? I really don't want to write off the phone as bricked, it should have about a year left in it before I consider replacing it.
Try this:
When powered off, attach headset to the phone. Then press power button.
My Touch Pro2 ran into the same situation recently, showing nothing but a 3-color screen with the same information as you listed. I haven't tried mtty but I found if I plug in the headset, it boots normally. No idea why...
It sounds like an error in the instruction set for the bootloader. Maybe cmonex can help you with a bootloader-friendly version of Hard SPL to re-flash.
cajunflavoredbob said:
It sounds like an error in the instruction set for the bootloader. Maybe cmonex can help you with a bootloader-friendly version of Hard SPL to re-flash.
Click to expand...
Click to collapse
he already has Hard-SPL so he could just reflash it with the Hard-SPL exe in manual mode, but as the version number is the same, the device may skip the updating of the SPL. if the OP wants to try this, I can make one with a different version number. though I seriously doubt that the issue would be fixed that way...
Headset trick
Hi,
Again, thanks to all that try to help me!
I tried the headset trick just now and look and behold, it actually worked! My limited brain can't come up with any plausible explenation but I'm happy anyway
I do remember reading about this trick at some point, but I couldn't locate a headset until today. Thanks lilei105!
Now I will reboot the unit several times to ensure this wasn't just a coincident.
Edit: Booted 4 times, still no problem. Have booted both with and without USB-cable connected to PC.
Yeah my advice would be re-flash it or install/download a different ROM.
i may be way off here, but could it be a problem with the volume down button on the unit? maybe the headset bypasses the standard volume button?

Categories

Resources