Develop Bugs

Usb cord came unplugged while updating rom tmobile dash.

The device is stuck in the windows mobile boot screen. Tried to do a hard reset but didnt do anything still stuck. Tried to get to boot screen didnt work by holding camera button but when took out battery and fired up with usb went to the tri color screen but would not connect to pc. How can I unbrick this?

1. Turn your phone off by removing the battery.
2. Put the battery back in.
3. While pushing down the camera button and holding it down, plug the usb cable in (while the other end is plugged into your computer)
4. You should see the tri colored screen and USB somewhere at the bottom. If it says "Serial" something's wrong.
5. Find a STOCK ROM for your phone, and flash it. Make sure it's an official upgrade exe, not some cooked ROM.
6. After all that's done.. proceed to flash the ROM of your choice.
To make sure this doesnt happen again, I would recommend the "hard spl" linked in the second or third post of my ROM thread (in my signature).

Upgrade ROM code error

I have flashed many Custome ROM's before. I have HardSPL installed on my phone.
I tried flashing to a ROM (I forget which one now, I think Cloudfa or something) and it stopped at about 15%. The Update utility stopped as well.
I cannot connect to bootloader at all. I tried holding down on Volume down/Reset to enter bootloader, but the thing is that it's already in bootloader with the message "Upgrade ROM code error, Please try again"
ActiveSync doesn't see my phone either. In fact all it does is just sit on the bootloader screen with that error...
Please Help... Thanks You...

A normal soft reset still brings you back to Bootloader?
What happens when you plug in your device? Does it not change from serial to USB at the bottom?

band27 said:
A normal soft reset still brings you back to Bootloader?
What happens when you plug in your device? Does it not change from serial to USB at the bottom?
Click to expand...
Click to collapse
Sorry. Yes it does show USB when plugged in, but won't respond to anything that I have tried software wise. It does not switch from this bootloader/error screen at any point. Even after I pull my battery and turn it back on...
I have yet to come across a thread which has this exact problem...

jzalapski said:
Sorry. Yes it does show USB when plugged in, but won't respond to anything that I have tried software wise. It does not switch from this bootloader/error screen at any point. Even after I pull my battery and turn it back on...
I have yet to come across a thread which has this exact problem...
Click to expand...
Click to collapse
Have you tried flashing a different ROM while in bootloader?

^^ Yes. It give me an error on my computer...
I would like to try the internal flashing method but I don't seem to have a way of getting at my Storage Card.
I found this thread with a similar problem
http://forum.xda-developers.com/showthread.php?t=480022
I WAS just able to get off of that screen I was talking about, but the best I get is to the Touch Diamond Screen that lists my ROM and such. So no real progress.
I have a feeling that I would resolve my problem if I could Flash from the Interanl Storage...

Have you tried hard resetting the device?
Pull out stylus and Holding....1) Vol. Down 2) Center Round button 3) then press red button aka soft reset with stylus

Nothing...

im stuck
hi all i am very new to this im not sure what i have done or how to fix the problem i download these this morning and they worked
rom version 1.57.831.1(47324)wwe
radio version 1.14.25.24
protocol version 52.64.25.34u
when i bootload in tri colours screen it shows
BLAC100 32M
SPL-1.56.OliNex
MicroP-Blackstone (led)v6
if it shows that i must of done something right i think of what ill read
and i have windows 7 ulitmate and i have Miri_WM65_21815_V19.0_Premium
when i double click on the BLACKSTONE RUU WRAPPER it crashes then i rename a new folder and done it from there and it works but it comes up wit error 208 file open? then i got told to rename to ruu_signed.nbh file to blacimg.nbh and to store it in the root of my sd card done that then somehow i got it to come up to the screen by Turn off the phone, press and keep pressed volume down button and while keeping it pressed turn on the phone then i see a message "Press power to flash your device" and i press power to flash got to 0% and it crashed and come up with Upgrade ROM code error plz try again and stuck in bootloader mode but now it wont even turn on its dead it wont turn on no matter what i do can someone plz help
all i want to do is get windows mobile 6.5 working i cant understand that it can be so hard to do
thanxs blueboys25!

Neeed DOCTOR for my HTC

Hello All,
My HTC Diamond Handset serial no is HT826K******* Tryed to change the ROM , but after reaching to 100% also the completed mesage is not coming . When I press the reset button Tri colour screen appears with error messgae " Upgrade ROM code error Please try Again".. . Please help

You probably don`t have the correct update package for your device... If you really want to update to this rom then you need the HardSPL. Install the HardSPL 1.93 Unsigned Developer edition.

do you have Hard-SPL?

I Recently updated through ROMUpdateUtility know i see touch diamond screen with RUU_Signed_1_93OliNex_HSPL_UnsignedEdition ...Please help

just flash another ROM while in bootloader and connected to usb. I would suggest to use a simply rom.

Hi,
But How , I am not able to copy the file to Internal memory as when I connect to laptop the the internal memory is not visible:

you don't need to put the nbh file in internal storage. Turn your device off. Press and hold the volume down button. While doing so press the power button. Keep holding the volume down button pressed until you see the multi colored screen which is called the bootloader. At the bottom it should say Serial. Using the USB cable with which you sync to your PC, plug the cable in to your PC and then plug the other end into your device.
The multi colored screen should soon say USB at the bottom of the screen. You are now ready to flash a new ROM. Just run the RUU as you would normally.

I did that; know I got the tri colour scree ;which says USB in white area know how to run RUU , my htc is connected to my laptop

create a folder on your pc and name it anything. now copy the nbh ans ruu.exe in that folder. run the ruu by double clicking it. this should be done when you get usb on your screen, if done correctly you rom flash should start flashing and a bar will appear on your phone.

Thanks All
Hi All,
Problem got fixed .
Solution used:-
Unsigned-Hard-SPL-Diamond-OliNex(2)

rumbles said:
you don't need to put the nbh file in internal storage. Turn your device off. Press and hold the volume down button. While doing so press the power button. Keep holding the volume down button pressed until you see the multi colored screen which is called the bootloader. At the bottom it should say Serial. Using the USB cable with which you sync to your PC, plug the cable in to your PC and then plug the other end into your device.
The multi colored screen should soon say USB at the bottom of the screen. You are now ready to flash a new ROM. Just run the RUU as you would normally.
Click to expand...
Click to collapse
so wut happens if i get no usb then wuts the matter ???
need to know what problem i have becuase i can never connect the fone via usb

Dynomite232 said:
so wut happens if i get no usb then wuts the matter ???
need to know what problem i have becuase i can never connect the fone via usb
Click to expand...
Click to collapse
Do you have the correct drivers installed?
Or Windows Mobile Device Center?
I think you need that I'm not too sure, I do anyway

[Q] bricked tilt 2

help please!
i preformed task 29 on my tilt 2 and i now have an ATT screen and wont go any further. when i try to stat it it only goes as far as the first screen and no further. i tried resting it to no avail. i can not establish connection with pc. i have vista for pc. can somebody help please?

Yes. now u preformed that, you want to plug in your USB. Push reset and the lower volum button at the same time. You will go into boot loader mode. It should say USB on the bottom once u have made a connection after connecting your USB to the computer. At that point flash your Radio, after flashing your radio, flash your rom. All like you normaly would ..
PS. make sure Sim and MScard is out of phone before preforming Flashing Radio, then the rom. Then replace the sim card after all the installation from the rom you are installing..

First go back to the task 29 post and read all the instructions.
Task 29 is a memory wiper,it completely wipes the memory of the device leaving only the radio and basic functions.
To get up and running again follow these instructions:
1. Download the newest stock rom for ATT found in the Rom Development forum. http://forum.xda-developers.com/showthread.php?t=737168
2. Remove back cover from the device, remove the battery, remove the SIM card and remove the SD card if you have one. Reinstall the battery, do not replace the back cover.
3. Power up the device and connect it to the PC. Press the down volume button and press and hold the stylus into the reset button, hold both until the boot screen appears. Windows may install some software at this time, let the software install.
4. When USB appears at the bottom of the boot screen run the ROM installer software run. Follow ALL on screen instructions.
NOTE: If you have Hard SPL installed you can install any custom ROM, if not you MUST install a STOCK SHIPPED ROM.

twh said:
help please!
i preformed task 29 on my tilt 2 and i now have an ATT screen and wont go any further. when i try to stat it it only goes as far as the first screen and no further. i tried resting it to no avail. i can not establish connection with pc. i have vista for pc. can somebody help please?
Click to expand...
Click to collapse
First of all check to see if your phone is hardspl'ed by turning phone completely off then hold volume down key then power phone back on from here you should be on tri-color screen see what the spl version says if it says 0.85Olinex it's hardspl'ed anything else is not hardspl'ed.
If your phone is hardspl'ed then your good all task29 does is wipe your entire os off your phone thats why it won't boot to nothing but the startup screen so in order for it to boot you need to flash a rom on to it, so like before power phone off hold volume down key & power phone on you should be on tri-color screen again at the bottom of phone screen it should say serial now plug in usb from computer now it should say usb at the bottom of phone find a rom that you like then flash it phone should reboot after flash & work like normal once again.
Hope this helps

thank you all you guys. you all were awesome. as you could imagine, i am new to wm. but with the help of every body, i got my phone up and running.

twh said:
thank you all you guys. you all were awesome. as you could imagine, i am new to wm. but with the help of every body, i got my phone up and running.
Click to expand...
Click to collapse
no problem i'm glad we all were able to help you

[Q] Light NHB removal.

So I currently have LightNHB flashed. Since WinMo wont work via USB until I check that one option (forget off hand) I can't establish a USB connection to flash my phone. I tried putting the RAPHIMG.nbh into my SD cards root but that also didn't work, during the boot it said there were no images to flash.
So I removed the Android OS files and reformatted my SD card then places the img file into the root again, and again no image was found.
How would I fix this issue? I cannot seem to flash my phone back to a different WinMo rom.

Got into LightNHB and it has no settings for the USB, it's all in ITA and only one thing I could find in the menus and it gives an error that the file cannot be found. Talk about bare-bones, no wonder I couldn't get this to connect to USB, I don't think it has the ability to.
Ideas?

Pull the battery, SIM(if you have one) and microSD card out.
Press and hold the volume down button while plugging in the USB cord and it should take you to the tri-color screen.
If you haven't already let go of the volume down button, do so now.
You should be ready to flash another ROM!
n-Joie!

R^7Z said:
Pull the battery, SIM(if you have one) and microSD card out.
Press and hold the volume down button while plugging in the USB cord and it should take you to the tri-color screen.
If you haven't already let go of the volume down button, do so now.
You should be ready to flash another ROM!
n-Joie!
Click to expand...
Click to collapse
Didn't know I could be like that but, sadly, error 260; followed to the letter :/
I can't get it to recognize .nbh. When I was able to get into the WinMo of LightNBH it seems it's WM5? CDMA? On my GSM phone... I know my version is dual CDMA and GSM. Though I use the latter.
It has HardSPL because Tri-colour screen says 1.90.OliNex

Can you get it to recognize USB in said bootloader mode? You should be able to flash from your PC using bootloader mode...

arrrghhh said:
Can you get it to recognize USB in said bootloader mode? You should be able to flash from your PC using bootloader mode...
Click to expand...
Click to collapse
No, from what I can gather LightNBH doesn't have the stock USB connection info included in WinMo. Settings > Connections was empty. In fact all of it is empty (settings), I couldn't get to my SD card to run cab files to give me control over my phone.
Is there anyone else running the LightNBH flash that can confirm this? I can't even establish a USB line within Android.

Ventrik101 said:
No, from what I can gather LightNBH doesn't have the stock USB connection info included in WinMo. Settings > Connections was empty. In fact all of it is empty (settings), I couldn't get to my SD card to run cab files to give me control over my phone.
Is there anyone else running the LightNBH flash that can confirm this? I can't even establish a USB line within Android.
Click to expand...
Click to collapse
Hrm, I figured bootloader mode would be separate from WinMo entirely... so not having usb drivers in WinMo should effect it.
So you're saying when you're in bootloader mode, and you plug in USB it still just says "serial"?

arrrghhh said:
Hrm, I figured bootloader mode would be separate from WinMo entirely... so not having usb drivers in WinMo should effect it.
So you're saying when you're in bootloader mode, and you plug in USB it still just says "serial"?
Click to expand...
Click to collapse
It doesn't even say serial.
Code:
RAPH100
SPL-1.90.OliNex
MicroP-Raph (LED) v13
MicroP-Raph (KEY) v5
PSOC-Raph STAGE_CVT v0x36
That's all my boot-loader says and I didn't think drivers had any effect here but as it sits I get an error 260 unable to connect from the ROM updater's that came with Monfro, TAEL, and Energy, as well as Task_29.

Erm... It should definitely say "Serial" near the bottom. Give it 10 secs or so...
When you plug into USB, that should convert to say USB...

Did you remember to rename the .nbh file into "RAPHIMG.nbh"? You could also use a sd card adapter or another device that has working usb storage that takes micro sd cards and then drag the .nbh file on the sd card via another device.

See what happens when we get in a hurry? At least that's how i ended up with Litenbh on my TP stuck in a boot loop.
I tried the PWR + VOL DN while soft resetting. No luck. Then i was going to try holding those 2 buttons while plugging it in to USB, I was holding the buttons as i unplugged it. It jumped to the serial screen as soon as i unplugged it.
I'm sure you have gotten this fixed or a new phone by now, but in case ur as broke as me, and still playin with a TP cause you HAVE to.
Maybe this will help. Hold power + volume down while plugging/unplugging it from the PC. Might get lucky like i did.
I know it says Development discontinued, but the TP is old enough that the info i'm looking for is getting buried. Most d/l links i find are dead now, so i'm getting jumpy on the clicker finger.
But I for one think this link and the file itself needs to be taken down. I know it's only 2 of us so far, but dangit what a pain!!!
http://forum.xda-developers.com/showthread.php?t=601751
EDIT: Wow i didnt realize this thread was that old also.
Alltel Touch Pro (yeah it's old, and the keyboard doesn't work)
Using Updated Alltel ROM from HTC site.

Hmmm...
FroYo thread
Gingerbread thread
And yes, this are continuing projects...
Please read the first few posts before attempting anything. It's really does not hurt to try but your experience may vary slightly if you don't know what you are doing.
On that note, I am PMing the thread OP/forum mod to see if there is a way to link to the continuing project threads.
Actually the first post in that thread that you make mention of, has a link to the continuing project.. heh