XDA EXEC stuck at spalsh screen after flashing - JASJAR, XDA Exec, MDA Pro Software Upgrading

Hai ,
I tried different flashes of WM6 , then i reverted back to wm5.
But then again i flashed it with wm6 rom.
It flashes it successfully but after hard reset , pressing 0 , it just stays at splash screen giving infos in red.
I am stuck at spalsh screen ... any ideas ?
Also tried uni_exitbootloader .. but still stucks at splash screen
Tried Refalshing it many times but same ..

babablacksheep said:
Hai ,
I tried different flashes of WM6 , then i reverted back to wm5.
But then again i flashed it with wm6 rom.
It flashes it successfully but after hard reset , pressing 0 , it just stays at splash screen giving infos in red.
I am stuck at spalsh screen ... any ideas ?
Also tried uni_exitbootloader .. but still stucks at splash screen
Tried Refalshing it many times but same ..
Click to expand...
Click to collapse
Try enter bootloader and re-flash WM6 Rom, if it still fails to boot, search the Universal forum for MTTY commands to reset partition tables. I suspect the partitions are corrupt.
Hope youre battery is not too low.
Cheers,
Beast

babablacksheep said:
Hai ,
I tried different flashes of WM6 , then i reverted back to wm5.
But then again i flashed it with wm6 rom.
It flashes it successfully but after hard reset , pressing 0 , it just stays at splash screen giving infos in red.
I am stuck at spalsh screen ... any ideas ?
Also tried uni_exitbootloader .. but still stucks at splash screen
Tried Refalshing it many times but same ..
Click to expand...
Click to collapse
Something like this happened to me when I first flashed my Universal, I tried something in the Wiki (Cannot remember?) That told me to use that usb port from now on for all flashing. After that it worked. I will search further to see if I can help...

Okie Problem Solved.
I did this to get myself sigh if relief.
100% working
1. Take out the SD and SIM cards
2. Opened ActiveSync and go to file, connection setting and Un-check "Allow USB Connections". Then press Ok and close ActiveSync
3. Put in bootloader mode (Power + Light + reset) which brings up the "un-backlit" screen with "Serial" at the top and v0.XX at the bottom
4. Plug in USB cable DIRECTLY from PC to Jasjar (MAKE SURE NOT TO USE A USB HUB). You MIGHT then see a warning window complaining that an "Unsigned" device driver is being attempted to be installed. You will be prompted to either "STOP INSTALLATION" or "CONTINUE ANYWAY" - this warning can be safely ignored and so just click on "CONTINUE ANYWAY".
5. Open mtty utility / software
6. Select USB from the "Port" drop-down on the upper left corner of the dialog box and hit OK
7. Then another screen will come up. Hit enter and that will show "USB>"
8. Type "task 28 55aa" and hit enter. {type it manually/ don`t copy and paste commands}
9. use the "Original OEM ROM" that is made for your device and update with it (CE,Extended and Radio) Flash all
10. Hard Reset
Also if your device bootloader version is lower than "v 1.01" you should update that first (before installing the OEM ROM, but NOT before "Task 28 55aa").
After this is complete you may then use your device again.
NOTe : I find you must kill the wcescomm, wcesmgr and rapimgr exe's using task manager before you get the 'usb' option in mtty (kills activesync)

Please,
what to do when there's no USB port in mtty (only COM1 and COM2) ?????

babablacksheep
must say -Thank you!

vjj said:
Please,
what to do when there's no USB port in mtty (only COM1 and COM2) ?????
Click to expand...
Click to collapse
You must disable ActiveSync before connection
and put in bootloader mode (Power + Light + reset) BEFORE run MTTY
after USB must appear in drop-down menu
one more time thanked babablacksheep

Related

Green/red/blue/white screen -.. Help :(

Ive installed bElite from bebe but now ive ***** everything up.. When i start my phone a red/green/blue/white screen appears and the message: "Upgrade ROM code error - please try again".. But how should i try again when im not able to connect to activesync?
Please help
Don't use bad words in ours forum..
you install "this" by doing "that" or simply search and read the wiki.
Thanks
Hmm ive installed HARDspl and now i want to upgrade to bebes ROM. My phone lost connection to activesync during this and ended.. Now i'm stuck at 1 % with no connection to activesync. How do i establish connection to activesync with a "dead" phone? its at red/green/blue screen....
Restart phone, then run the installer again.
Entrak said:
Restart phone, then run the installer again.
Click to expand...
Click to collapse
When i restart my phone the white/green/blue/red screen turns up again at it still says "Upgrade ROM code error"??
note to n00b
if not sure.....read and search before you jump in head first
welcome to the forum
liamhere said:
if not sure.....read and search before you jump in head first
welcome to the forum
Click to expand...
Click to collapse
Yeah its easy for you to say ive only got my phone for a couple of days and now im ****ting green pigs scared of having destroyed my phone!
can't anyone please help?
you could try a hardreset and hope this will work...
ArtaxXP said:
you could try a hardreset and hope this will work...
Click to expand...
Click to collapse
the two volume buttons, the round button in the middle (enter) and the red dot where the pen is fastened, right? it isnt working
ArtaxXP said:
you could try a hardreset and hope this will work...
Click to expand...
Click to collapse
hope this helps
http://forum.xda-developers.com/showthread.php?t=402530&highlight=hard+reset
technically you need to do this:
You need Windows XP computer running ActiveSync. Vista is no good for the following procedure.
1. search for mtty.exe on this forum and download it:
2. connect you phone over USB cable to computer
3. in activesync settings : disable USB connectivity
4. launch mtty
5. in drop down list select USB port as connection option
6. mtty will connect to your Diamond
7. press :ENTER key
8. type as follows in command line:
set 16 0 0
9. press enter
10. disconnect USB cable and remove battery from your phone
you phone will boot normaly this time.
Take it easy... You have not damaged your phone... simply start the ROM installation process again while having your diamond docked and showing the red/green/blue screen... There should also be a message showing USB at the bottom of the screen...
liamhere said:
hope this helps
http://forum.xda-developers.com/showthread.php?t=402530&highlight=hard+reset
Click to expand...
Click to collapse
thanks but no, it isn't working.. how come im the only one who tried this? isnt there anything to do?
it's not as easy as it sounds to perform a hardreset because it seems to be impossible to hold the required key all together...but with some practising it should work...
_Nomad_
no chance upgrading the firmware if phone was not HSPL-ed first. hard reset will not help. if phone stucked in boootloader.
see what I have written above. this is how to get phone out of bootloader screen in 3 seconds. no hard reset required.
SecureGSM said:
technically you need to do this:
You need Windows XP computer running ActiveSync. Vista is no good for the following procedure.
1. search for mtty.exe on this forum and download it:
2. connect you phone over USB cable to computer
3. in activesync settings : disable USB connectivity
4. launch mtty
5. in drop down list select USB port as connection option
6. mtty will connect to your Diamond
7. press :ENTER key
8. type as follows in command line:
set 16 0 0
9. press enter
10. disconnect USB cable and remove battery from your phone
you phone will boot normaly this time.
Click to expand...
Click to collapse
thanks but its still showing the multicoloured screen? after ive inserted "set 16 0 0" should i save it somewhere or?
Where exactly have you inserted this:
set 16 0 0 ?
you need to use mtty.exe program. see above
SecureGSM said:
Where exactly have you inserted this:
set 16 0 0 ?
you need to use mtty.exe program. see above
Click to expand...
Click to collapse
ive done as you said. ive started mtty.exe and there is a blank page. in this blank page i pressed the enter-button and cmd> was shown. then i wrote set 16 0 0 like you said and pressed the enter-button one more time?
good. now just unplug USB cable. remove battery, place battery back and power up you handset. it should go into normal mode instead of bootloader mode.
set 16 0 0 - sets flag to boot normaly
the multicoloured screen still appears! and it still says "Upgrade ROM code error - please try again".. Do you have 2 minutes to explain it to me on MSN? p0ulsen90 a gmail.com

Diamond not conecting

I want to upgrade rom on may diamond but when conect the phone to my conputer the phone it just starts to charge. The computer does not detect him and I have activated usb conection on the phone.
I am using a standard miniusb cable used also for canon fotcamera, Nokia N95, motorola V3 (v360 L6, L7 etc.)
I did instaled Activesync on my computer but still no result.
You did no say which Win OS you are using - If Vista then you do not need activesync (AS) but windows mobile device centre or any other Win OS Before Vista then AS is what you need. AS needs to be installed before you connect your phone to the PC.
Have you restarted your PC first before install - this also helps sometimes
Try this....
Start>Settings>Connections>USB to PC and here ....uncheck the box Enable advanced network functionality
Just a reminder to please use the Internal Method when flashing a new Rom or Radio. Do not rely on your PC as errors occur more frequently.
R3PUBL1K said:
You did no say which Win OS you are using - If Vista then you do not need activesync (AS) but windows mobile device centre or any other Win OS Before Vista then AS is what you need. AS needs to be installed before you connect your phone to the PC.
Have you restarted your PC first before install - this also helps sometimes
Click to expand...
Click to collapse
I am using Win XP SP2 and I have tried every thing that you said but nothing.
band27 said:
Try this....
Start>Settings>Connections>USB to PC and here ....uncheck the box Enable advanced network functionality
Just a reminder to please use the Internal Method when flashing a new Rom or Radio. Do not rely on your PC as errors occur more frequently.
Click to expand...
Click to collapse
I did uncheck that box but without any results so now I will try internal method. But I'll have to send the file to the phone via bluetooth and see if it works.
band27 said:
Just a reminder to please use the Internal Method when flashing a new Rom or Radio. Do not rely on your PC as errors occur more frequently.
Click to expand...
Click to collapse
How much is it supose to take "Internal method"?
After pressing Vol_Down + Back button it showed the three color screen then it changed to a white screen with loading on it and it stays like that (after pressing Vol_Down + Back button I didn't press nothing else).
The Internal Method shouldn't take you any longer then 2 min. or so.
Once you have started the flashing to begin in the Grey menu....it will eventually say OK...OK
and yes
at this stage you soft reset and press vol down and centre round button.
Grey menu then gives you a choice to reset back to manufactures settings which is what you want (vol UP)......this should take an additions 2 min. if that.
band27 said:
The Internal Method shouldn't take you any longer then 2 min. or so.
Once you have started the flashing to begin in the Grey menu....it will eventually say OK...OK
and yes
at this stage you soft reset and press vol down and centre round button.
Grey menu then gives you a choice to reset back to manufactures settings which is what you want (vol UP)......this should take an additions 2 min. if that.
Click to expand...
Click to collapse
I have tried everything that you said and nothing.
The only diference is that now when I conect the cable to the phone it asks me witch mode to conect it (Activesync or storage), but the computer still doesn't see's it.
Tried another USB-cable?
chribruu said:
Tried another USB-cable?
Click to expand...
Click to collapse
I tried with 3 diferent cables.
Have you tried putting your device into bootload mode (soft reset & vol. down) and the connecting to your pc. The bottom of your coloured screen should switch from serial to usb....If this switches to USB then you are good to go with downloading what ever Rom using the RUU_
Keep me posted...
band27 said:
Have you tried putting your device into bootload mode (soft reset & vol. down) and the connecting to your pc. The bottom of your coloured screen should switch from serial to usb....If this switches to USB then you are good to go with downloading what ever Rom using the RUU_
Keep me posted...
Click to expand...
Click to collapse
It doesn't switch's to usb it only shows "serial". If I put it into bootmode while it is conected to USB it shows nothing, not "USB" or "Serial" it's blank.
I am begining to belive that there is a hardware problem in my phone.
Do you have .NET framework installed on your PC! if not, get it from http://www.microsoft.com/downloads/d...DisplayLang=en

Upgrade ROM code error

I have flashed many Custome ROM's before. I have HardSPL installed on my phone.
I tried flashing to a ROM (I forget which one now, I think Cloudfa or something) and it stopped at about 15%. The Update utility stopped as well.
I cannot connect to bootloader at all. I tried holding down on Volume down/Reset to enter bootloader, but the thing is that it's already in bootloader with the message "Upgrade ROM code error, Please try again"
ActiveSync doesn't see my phone either. In fact all it does is just sit on the bootloader screen with that error...
Please Help... Thanks You...
A normal soft reset still brings you back to Bootloader?
What happens when you plug in your device? Does it not change from serial to USB at the bottom?
band27 said:
A normal soft reset still brings you back to Bootloader?
What happens when you plug in your device? Does it not change from serial to USB at the bottom?
Click to expand...
Click to collapse
Sorry. Yes it does show USB when plugged in, but won't respond to anything that I have tried software wise. It does not switch from this bootloader/error screen at any point. Even after I pull my battery and turn it back on...
I have yet to come across a thread which has this exact problem...
jzalapski said:
Sorry. Yes it does show USB when plugged in, but won't respond to anything that I have tried software wise. It does not switch from this bootloader/error screen at any point. Even after I pull my battery and turn it back on...
I have yet to come across a thread which has this exact problem...
Click to expand...
Click to collapse
Have you tried flashing a different ROM while in bootloader?
^^ Yes. It give me an error on my computer...
I would like to try the internal flashing method but I don't seem to have a way of getting at my Storage Card.
I found this thread with a similar problem
http://forum.xda-developers.com/showthread.php?t=480022
I WAS just able to get off of that screen I was talking about, but the best I get is to the Touch Diamond Screen that lists my ROM and such. So no real progress.
I have a feeling that I would resolve my problem if I could Flash from the Interanl Storage...
Have you tried hard resetting the device?
Pull out stylus and Holding....1) Vol. Down 2) Center Round button 3) then press red button aka soft reset with stylus
Nothing...
im stuck
hi all i am very new to this im not sure what i have done or how to fix the problem i download these this morning and they worked
rom version 1.57.831.1(47324)wwe
radio version 1.14.25.24
protocol version 52.64.25.34u
when i bootload in tri colours screen it shows
BLAC100 32M
SPL-1.56.OliNex
MicroP-Blackstone (led)v6
if it shows that i must of done something right i think of what ill read
and i have windows 7 ulitmate and i have Miri_WM65_21815_V19.0_Premium
when i double click on the BLACKSTONE RUU WRAPPER it crashes then i rename a new folder and done it from there and it works but it comes up wit error 208 file open? then i got told to rename to ruu_signed.nbh file to blacimg.nbh and to store it in the root of my sd card done that then somehow i got it to come up to the screen by Turn off the phone, press and keep pressed volume down button and while keeping it pressed turn on the phone then i see a message "Press power to flash your device" and i press power to flash got to 0% and it crashed and come up with Upgrade ROM code error plz try again and stuck in bootloader mode but now it wont even turn on its dead it wont turn on no matter what i do can someone plz help
all i want to do is get windows mobile 6.5 working i cant understand that it can be so hard to do
thanxs blueboys25!

Bricked Diamond

Hi folks,
Can anyone help me?
I was using BSB 6.5L WM6.5 on my Diamond and i had some problems with that.
Mainly, my Diamond was "hard reseting" the manufactures settings everytime i turned it on.
So i decided to downgrade it to WM 6.1
At this point i started to have serious issues.
I installed Rom 1.93xx and just after the uptade, my Diamond froze in the first black screen (Touch Diamond and radio/Rom version).
Even if i do the hard reset, it freezes again in the boot screen.?
So, how could i go back to the Rom i was using before or install another one?
My Diamond is useless now... Hope someone can help me.
Thanks
should've used search, this is also a wrong forum for this topic.
with that said, power off the phone, press and hold power, volume down and reset until you see the tri-colour bootloader screen, connect the phone to your PC, you should be able to flash at this point.
do report back.
Japex said:
Hi folks,
Can anyone help me?
I was using BSB 6.5L WM6.5 on my Diamond and i had some problems with that.
Mainly, my Diamond was "hard reseting" the manufactures settings everytime i turned it on.
So i decided to downgrade it to WM 6.1
At this point i started to have serious issues.
I installed Rom 1.93xx and just after the uptade, my Diamond froze in the first black screen (Touch Diamond and radio/Rom version).
Even if i do the hard reset, it freezes again in the boot screen.?
So, how could i go back to the Rom i was using before or install another one?
My Diamond is useless now... Hope someone can help me.
Thanks
Click to expand...
Click to collapse
What technote said is incorrect, doing that will just cause it to try and read from the Internal Storage, what you want to do is what I did when I had the exact same problem;
With the phone on the frozen screen - make sure the USB cable is DISconnected, open ActiveSync/WMDC on the PC and in connection settings, disable USB connections. Now press the red reset button on the phone and as the phone is turning on (before it vibrates - 'touch Diamond' splash), you need to press Volume Down once, don't hold it. Just press it once. Now plug the USB cable in when the tri color screen appears, and Serial should be written near the bottom. Renable USB connections in ActiveSync/WMDC and then flash a ROM. All should work.
Thanks...
It worked flawlessly....
incredulous said:
What technote said is incorrect, doing that will just cause it to try and read from the Internal Storage, what you want to do is what I did when I had the exact same problem;
With the phone on the frozen screen - make sure the USB cable is DISconnected, open ActiveSync/WMDC on the PC and in connection settings, disable USB connections. Now press the red reset button on the phone and as the phone is turning on (before it vibrates - 'touch Diamond' splash), you need to press Volume Down once, don't hold it. Just press it once. Now plug the USB cable in when the tri color screen appears, and Serial should be written near the bottom. Renable USB connections in ActiveSync/WMDC and then flash a ROM. All should work.
Click to expand...
Click to collapse
When i do this, it still keeps going to the splash. I reset, press vol down, and it continues to go to the splash. If i do it the other mentioned way, power, reset, vol down i get to the tri colour screen.
how to enter in bootloader = press volume down and reset simultaneous !
link

HELP PLZ!!!!! (rom fail ?)

Hi all u guys out there hope someone can help me i installed this rom on my diamond the name was TEAL or some like that the first few times it was fine but then my battery was running low and then when i turned my diamond on again i had 2 setup mobile and now it just keep showing the screen that says it wanna setup and i cant acess USB from there so plz if u can help me recover my diamond plz reply
try update from Boot Screen
Blackster..try updatin frm boot screen..go in boot screen & then connect it to usb & try updatin the ROM...
to get in your bootscreen just reset your device while holding the volume down button
just so you know ^^
Tried every thing
,My vista wont show the usb from hardSPL and i cant connect from the setup and when i just installed the rom again it wont work
nothings work plz help
USB??
its just installing the usb driver but show no usb
simple thing
just run RUU from u'r PC...
Follow 1st Two steps by clicking next...
no need to perform mentioned task in RUU.
Connect USB Cable PC to Diamond...
On diamond hold on off button and volume down button and hit reset button on back..
you will forwarded to boot screen on diamond...
It will automaticly identify u'r USB connection to PC...
Once it displays USB on diamond boot menu, Hit Update button on RUU running on PC...
Then follow the RUU instructions...
Once finished, you have done...

Categories

Resources