[Q] looses connection to active sync. - Touch Diamond, MDA Compact IV ROM Development

hello. sorry for my poor english. i am trying to install a ROM on my htc diamond but when the flashing starts my phone looses connection to my pc (active sync) this happends when the 3 color lines is shown on my phone's screen. do anyone know how to fix this problem. thanks

ROM Update
xvision1992 said:
hello. sorry for my poor english. i am trying to install a ROM on my htc diamond but when the flashing starts my phone looses connection to my pc (active sync) this happends when the 3 color lines is shown on my phone's screen. do anyone know how to fix this problem. thanks
Click to expand...
Click to collapse
Hi!
Not sure if that works but if this is your first time to flash the drivers to recognize your device in bootloader mode needs to be installed which takes some time.
Try to put your device into bootloader mode (keep VolDown pressed during reset) than plug in USB. Diamond screen at bottom will change from Serial to USB if recognized and device drivers installed.
Now start up ROM Update and perform flash. You should MTTY before every flash.
Regards,
Cina.

Related

HELP!! Diamond Stuck in bootlaoder

Help pls i have olinex 1.40 hardspl in but my phone is stuck in bootloader with "upgrade ROM code error Please try again" i cant get out...tried hard reset nothing...tried recovery mode (volume down + reset ) nothing...cant get a usb connection help!!!!!!!!!!!!!!!!
are you sure you don't have usb connection? try running an ruu with usb plugged in see if it runs. it sounds like you tried to flash a radio from another device. try flashing a new radio.
Blazeitup123 said:
are you sure you don't have usb connection? try running an ruu with usb plugged in see if it runs. it sounds like you tried to flash a radio from another device. try flashing a new radio.
Click to expand...
Click to collapse
the bootloader shows usb when i plug it in and serial when i plug it out...when hard resetting it goes through the formatting but then just jumps back to bootloader with the message...active sync recognizes nothing but i'll try that right now
edit - ok it seems to be flashing i'm crossing my fingers
edit: ok it seems to have flashed i see my rogers main screen thank you soooooooooooooooo much
glad to hear!
just so you know you can always flash from bootloader. i have seen alot of people around here saying "oh no, my device is bricked and i'm stuck in bootloader". i lol.
Blazeitup123 said:
glad to hear!
just so you know you can always flash from bootloader. i have seen alot of people around here saying "oh no, my device is bricked and i'm stuck in bootloader". i lol.
Click to expand...
Click to collapse
lmao now i know..i was coming from an elfin, not used to diamond as of yet but now i know
Bootloader bottom says "serial" but wont switch to "usb"
Perhaps this is a known issue but I could not find the solution easily and ended up discovering it myself so wanted to share it in case others face the same.
I was try to use the mtty software to "clean" my touch diamond in an effort to get rid of some bugs in macadam 1.2 rom [great rom, by the way].
I had disabled the usb connections in active sync on my laptop [mac running windows xp in bootcamp]
I could enter bootloader easily but the bottom part of the multicolor screen kept saying "serial" and would not switch to "usb" when I connected the phone to the laptop.
What finally worked was ensuring that the phone was set for "activesync" rather than use as a "disk drive" or "internet sharing". I had assumed, wrongly, that once in bootloader the last selected option [disk drive] would be irrelevant.
So I exited the bootloader by pressing the reset key; connected phone to pc via cable; selected the active sync option; disconnected the phone; entered bootloader, connected the phone via cable again and the bottom of the bootloader changed to usb and I was able to use mtty successfully.
I wonder if this has implications for people stuck with bad flashes etc. In my case I could easily exit the bootloader and go back and select 'activesync' from the working phone. One could also hard reset if a working rom was on the phone...
BUT If one is stuck with the option of only the bootloader, would it matter on what the last selected option was [active sync or use as usb disk drive or internet sharing]?
faisal said:
Perhaps this is a known issue but I could not find the solution easily and ended up discovering it myself so wanted to share it in case others face the same.
I was try to use the mtty software to "clean" my touch diamond in an effort to get rid of some bugs in macadam 1.2 rom [great rom, by the way].
I had disabled the usb connections in active sync on my laptop [mac running windows xp in bootcamp]
I could enter bootloader easily but the bottom part of the multicolor screen kept saying "serial" and would not switch to "usb" when I connected the phone to the laptop.
What finally worked was ensuring that the phone was set for "activesync" rather than use as a "disk drive" or "internet sharing". I had assumed, wrongly, that once in bootloader the last selected option [disk drive] would be irrelevant.
So I exited the bootloader by pressing the reset key; connected phone to pc via cable; selected the active sync option; disconnected the phone; entered bootloader, connected the phone via cable again and the bottom of the bootloader changed to usb and I was able to use mtty successfully.
I wonder if this has implications for people stuck with bad flashes etc. In my case I could easily exit the bootloader and go back and select 'activesync' from the working phone. One could also hard reset if a working rom was on the phone...
BUT If one is stuck with the option of only the bootloader, would it matter on what the last selected option was [active sync or use as usb disk drive or internet sharing]?
Click to expand...
Click to collapse
This doesn't make any difference. When you're stuck in bootloader just plugin your USB and the display will state "USB" as well. You can flash a rom at this point.

Diamond not conecting

I want to upgrade rom on may diamond but when conect the phone to my conputer the phone it just starts to charge. The computer does not detect him and I have activated usb conection on the phone.
I am using a standard miniusb cable used also for canon fotcamera, Nokia N95, motorola V3 (v360 L6, L7 etc.)
I did instaled Activesync on my computer but still no result.
You did no say which Win OS you are using - If Vista then you do not need activesync (AS) but windows mobile device centre or any other Win OS Before Vista then AS is what you need. AS needs to be installed before you connect your phone to the PC.
Have you restarted your PC first before install - this also helps sometimes
Try this....
Start>Settings>Connections>USB to PC and here ....uncheck the box Enable advanced network functionality
Just a reminder to please use the Internal Method when flashing a new Rom or Radio. Do not rely on your PC as errors occur more frequently.
R3PUBL1K said:
You did no say which Win OS you are using - If Vista then you do not need activesync (AS) but windows mobile device centre or any other Win OS Before Vista then AS is what you need. AS needs to be installed before you connect your phone to the PC.
Have you restarted your PC first before install - this also helps sometimes
Click to expand...
Click to collapse
I am using Win XP SP2 and I have tried every thing that you said but nothing.
band27 said:
Try this....
Start>Settings>Connections>USB to PC and here ....uncheck the box Enable advanced network functionality
Just a reminder to please use the Internal Method when flashing a new Rom or Radio. Do not rely on your PC as errors occur more frequently.
Click to expand...
Click to collapse
I did uncheck that box but without any results so now I will try internal method. But I'll have to send the file to the phone via bluetooth and see if it works.
band27 said:
Just a reminder to please use the Internal Method when flashing a new Rom or Radio. Do not rely on your PC as errors occur more frequently.
Click to expand...
Click to collapse
How much is it supose to take "Internal method"?
After pressing Vol_Down + Back button it showed the three color screen then it changed to a white screen with loading on it and it stays like that (after pressing Vol_Down + Back button I didn't press nothing else).
The Internal Method shouldn't take you any longer then 2 min. or so.
Once you have started the flashing to begin in the Grey menu....it will eventually say OK...OK
and yes
at this stage you soft reset and press vol down and centre round button.
Grey menu then gives you a choice to reset back to manufactures settings which is what you want (vol UP)......this should take an additions 2 min. if that.
band27 said:
The Internal Method shouldn't take you any longer then 2 min. or so.
Once you have started the flashing to begin in the Grey menu....it will eventually say OK...OK
and yes
at this stage you soft reset and press vol down and centre round button.
Grey menu then gives you a choice to reset back to manufactures settings which is what you want (vol UP)......this should take an additions 2 min. if that.
Click to expand...
Click to collapse
I have tried everything that you said and nothing.
The only diference is that now when I conect the cable to the phone it asks me witch mode to conect it (Activesync or storage), but the computer still doesn't see's it.
Tried another USB-cable?
chribruu said:
Tried another USB-cable?
Click to expand...
Click to collapse
I tried with 3 diferent cables.
Have you tried putting your device into bootload mode (soft reset & vol. down) and the connecting to your pc. The bottom of your coloured screen should switch from serial to usb....If this switches to USB then you are good to go with downloading what ever Rom using the RUU_
Keep me posted...
band27 said:
Have you tried putting your device into bootload mode (soft reset & vol. down) and the connecting to your pc. The bottom of your coloured screen should switch from serial to usb....If this switches to USB then you are good to go with downloading what ever Rom using the RUU_
Keep me posted...
Click to expand...
Click to collapse
It doesn't switch's to usb it only shows "serial". If I put it into bootmode while it is conected to USB it shows nothing, not "USB" or "Serial" it's blank.
I am begining to belive that there is a hardware problem in my phone.
Do you have .NET framework installed on your PC! if not, get it from http://www.microsoft.com/downloads/d...DisplayLang=en

Neeed DOCTOR for my HTC

Hello All,
My HTC Diamond Handset serial no is HT826K******* Tryed to change the ROM , but after reaching to 100% also the completed mesage is not coming . When I press the reset button Tri colour screen appears with error messgae " Upgrade ROM code error Please try Again".. . Please help
You probably don`t have the correct update package for your device... If you really want to update to this rom then you need the HardSPL. Install the HardSPL 1.93 Unsigned Developer edition.
do you have Hard-SPL?
I Recently updated through ROMUpdateUtility know i see touch diamond screen with RUU_Signed_1_93OliNex_HSPL_UnsignedEdition ...Please help
just flash another ROM while in bootloader and connected to usb. I would suggest to use a simply rom.
Hi,
But How , I am not able to copy the file to Internal memory as when I connect to laptop the the internal memory is not visible:
you don't need to put the nbh file in internal storage. Turn your device off. Press and hold the volume down button. While doing so press the power button. Keep holding the volume down button pressed until you see the multi colored screen which is called the bootloader. At the bottom it should say Serial. Using the USB cable with which you sync to your PC, plug the cable in to your PC and then plug the other end into your device.
The multi colored screen should soon say USB at the bottom of the screen. You are now ready to flash a new ROM. Just run the RUU as you would normally.
I did that; know I got the tri colour scree ;which says USB in white area know how to run RUU , my htc is connected to my laptop
create a folder on your pc and name it anything. now copy the nbh ans ruu.exe in that folder. run the ruu by double clicking it. this should be done when you get usb on your screen, if done correctly you rom flash should start flashing and a bar will appear on your phone.
Thanks All
Hi All,
Problem got fixed .
Solution used:-
Unsigned-Hard-SPL-Diamond-OliNex(2)
rumbles said:
you don't need to put the nbh file in internal storage. Turn your device off. Press and hold the volume down button. While doing so press the power button. Keep holding the volume down button pressed until you see the multi colored screen which is called the bootloader. At the bottom it should say Serial. Using the USB cable with which you sync to your PC, plug the cable in to your PC and then plug the other end into your device.
The multi colored screen should soon say USB at the bottom of the screen. You are now ready to flash a new ROM. Just run the RUU as you would normally.
Click to expand...
Click to collapse
so wut happens if i get no usb then wuts the matter ???
need to know what problem i have becuase i can never connect the fone via usb
Dynomite232 said:
so wut happens if i get no usb then wuts the matter ???
need to know what problem i have becuase i can never connect the fone via usb
Click to expand...
Click to collapse
Do you have the correct drivers installed?
Or Windows Mobile Device Center?
I think you need that I'm not too sure, I do anyway

HELP PLZ!!!!! (rom fail ?)

Hi all u guys out there hope someone can help me i installed this rom on my diamond the name was TEAL or some like that the first few times it was fine but then my battery was running low and then when i turned my diamond on again i had 2 setup mobile and now it just keep showing the screen that says it wanna setup and i cant acess USB from there so plz if u can help me recover my diamond plz reply
try update from Boot Screen
Blackster..try updatin frm boot screen..go in boot screen & then connect it to usb & try updatin the ROM...
to get in your bootscreen just reset your device while holding the volume down button
just so you know ^^
Tried every thing
,My vista wont show the usb from hardSPL and i cant connect from the setup and when i just installed the rom again it wont work
nothings work plz help
USB??
its just installing the usb driver but show no usb
simple thing
just run RUU from u'r PC...
Follow 1st Two steps by clicking next...
no need to perform mentioned task in RUU.
Connect USB Cable PC to Diamond...
On diamond hold on off button and volume down button and hit reset button on back..
you will forwarded to boot screen on diamond...
It will automaticly identify u'r USB connection to PC...
Once it displays USB on diamond boot menu, Hit Update button on RUU running on PC...
Then follow the RUU instructions...
Once finished, you have done...

Heeeeeeeelp!!!!!

If this is a spam, plz forgive me
Well, 2 all. I booted my Diamond with a 6.5 ROM. Normallt, it worked well. But this time, the ROM got some mistake that when it was goin' to finish, it froze it still kept the static in 30 mins later, and I got to reset it. Then, my Diamond restarted, and... froze at the Bootloader screen (3 colors screen) ( I tried all things to recover it, searching on the web, but nothing's ok I plugged it into my PC and my PC doesn't recognize it ( anyone knows out there plz help!!!!!!!
which version of windows operating system are you using. also try to reset and then again go into bootloader MANUALLY by pressing volume down key. see if the pc detects. also do you have ur stock rom?
meteorain08 said:
If this is a spam, plz forgive me
Well, 2 all. I booted my Diamond with a 6.5 ROM. Normallt, it worked well. But this time, the ROM got some mistake that when it was goin' to finish, it froze it still kept the static in 30 mins later, and I got to reset it. Then, my Diamond restarted, and... froze at the Bootloader screen (3 colors screen) ( I tried all things to recover it, searching on the web, but nothing's ok I plugged it into my PC and my PC doesn't recognize it ( anyone knows out there plz help!!!!!!!
Click to expand...
Click to collapse
enter bootloader, connect to PC. in white bar the 'Serial' will change to 'USB'
then you can run customeRUU to flash again
if the PC don't detect, try on other PC.
Well, if u know how to up ROM via PC then tell me, because I often up ROM directly on my Diamond, not via PC. And I plugged it to PC and the word "Serial" disappeared, but the word "USB" did not display on the screen
Did you make MTTY befor instal 6.5 rom try to make it and reinstal the rom

Categories

Resources