i am tring to flash the imate jasjam rom i downloaded from imate website, i plug it in and activesync connects, but when i get to the "verifying information on pda" my pda goes into bootloader and then i get error 260 or something saying im not connected! please help!
any ideas?
Install Hard SPL V7 then use sd card method.
try this
put the phone into boot loader mode (power off press and hold comm button and ok buttons at same time and power on the device)
screen should say serial, plug in usb, screen should change to usb, then run the rom (ruu file) on your pc
Related
My Xdaexec not connecting to PC in bootloader mode. While I was uograding the rom, the computer shutdown. And did not finish th upgrade. Please can any one help me how to solve this problem. Tanks a lot.
when you plug in the usb, the bootloader screen should show 'usb', your pc will not show anything. start the ruu and it should work as normal
try 2 read wiki -how2 upgrade thru bootloader, try2 dwnld Uni_exit_bootloader.exe, mtty, but first if u are in bootloader flash again (and use ups for pc)
Hello All,
My HTC Diamond Handset serial no is HT826K******* Tryed to change the ROM , but after reaching to 100% also the completed mesage is not coming . When I press the reset button Tri colour screen appears with error messgae " Upgrade ROM code error Please try Again".. . Please help
You probably don`t have the correct update package for your device... If you really want to update to this rom then you need the HardSPL. Install the HardSPL 1.93 Unsigned Developer edition.
do you have Hard-SPL?
I Recently updated through ROMUpdateUtility know i see touch diamond screen with RUU_Signed_1_93OliNex_HSPL_UnsignedEdition ...Please help
just flash another ROM while in bootloader and connected to usb. I would suggest to use a simply rom.
Hi,
But How , I am not able to copy the file to Internal memory as when I connect to laptop the the internal memory is not visible:
you don't need to put the nbh file in internal storage. Turn your device off. Press and hold the volume down button. While doing so press the power button. Keep holding the volume down button pressed until you see the multi colored screen which is called the bootloader. At the bottom it should say Serial. Using the USB cable with which you sync to your PC, plug the cable in to your PC and then plug the other end into your device.
The multi colored screen should soon say USB at the bottom of the screen. You are now ready to flash a new ROM. Just run the RUU as you would normally.
I did that; know I got the tri colour scree ;which says USB in white area know how to run RUU , my htc is connected to my laptop
create a folder on your pc and name it anything. now copy the nbh ans ruu.exe in that folder. run the ruu by double clicking it. this should be done when you get usb on your screen, if done correctly you rom flash should start flashing and a bar will appear on your phone.
Thanks All
Hi All,
Problem got fixed .
Solution used:-
Unsigned-Hard-SPL-Diamond-OliNex(2)
rumbles said:
you don't need to put the nbh file in internal storage. Turn your device off. Press and hold the volume down button. While doing so press the power button. Keep holding the volume down button pressed until you see the multi colored screen which is called the bootloader. At the bottom it should say Serial. Using the USB cable with which you sync to your PC, plug the cable in to your PC and then plug the other end into your device.
The multi colored screen should soon say USB at the bottom of the screen. You are now ready to flash a new ROM. Just run the RUU as you would normally.
Click to expand...
Click to collapse
so wut happens if i get no usb then wuts the matter ???
need to know what problem i have becuase i can never connect the fone via usb
Dynomite232 said:
so wut happens if i get no usb then wuts the matter ???
need to know what problem i have becuase i can never connect the fone via usb
Click to expand...
Click to collapse
Do you have the correct drivers installed?
Or Windows Mobile Device Center?
I think you need that I'm not too sure, I do anyway
Hi everybody,
I look through the threads and I couldn't find a solution to my troubles. So here it is: I just bought a htc touch pro 2 which came with a window mobile 6.1. Before I transferred anything from my old phone, I thought better to do the official upgrade to 6.5 ROM version 1.86.401.0.
I wanted to flash the ROM through a USB cable as described on the HTC site, but after after having done 22% of the work, everything got stuck. And 5' minutes afterward the update windows on the PC disappeared and I had to disconnect the phone!!!
So now I have a beatiful telephone, which cannot boot up. Indeed, it gets stuck in the 4 colors bootloader.
i) I tried to do a factory reset (pressing power, send hang up buttons) to no avail.
ii) I tried to take out the batteries and pull them in again, then switching on the phone holding down the vol down + power up buttons, then reset.
iii) reconnecting the phone back to the PC by usb, I was never able to get a switch from "serial" to "usb"
Nothing is working, if anybody has an idea what I could try next.... I am wondering if it is possible to flash the phone from the SD card. I am really a newbie here.
Thanks
Max
Yea .. same thing happened to me ..
Check Here For Full Info: Click Here
*Go into BootLoader Mode (do a Soft Reset while holding the "volume down" key on the left side of the device. Keep holding the "volume down" key until you see tricolour screen which is the bootloader mode, then release it)
Flashing Via MicroSD Card
1. Make sure your microSD is Formatted to fat32 (you dont have to delete all files but it is safer if you do)
2. Download your prefered Rom from the Rhodium Rom Develpoment Page and unzip/unrar it to your PC
3. Goto the Roms Folder and rename the .nbh file to RHODIMG.nbh
4. Copy the RHODIMG.nbh file to the root of your MicroSD Card
5. Plug the MicroSD Card into the phone
6. Enter the BootLoader screen, you will first see a tri-color screen with the phone and SPL Information at the top
7. Follow the On Screen instructions to start the update
8. After flash has completed, press the reset button with the stylus to reset the device.
Good Luck ! Worked For me !
Thanks for your help and the link to the thread!! I will use your approach next time. Indeed, in the day afterwards I was able to finally flash the phone from the same PC. I did the manipulation, which failed miserably, with a 64 bit Windows 7 RC. Then, I realised I had another version of W7 on the same PC, a 32 bit version this time. Thus, when I tried it with my dying telephone, the "serial" message on its screen switched "magically" to "usb" and I finally could flash the damned mobile! Frankly, I don't know what's wrong with my 64bit W7 if anything.
Cheers
Max
my htc pro2 failed upgrade: any help
WarlockW said:
Yea .. same thing happened to me ..
Check Here For Full Info: Click Here
*Go into BootLoader Mode (do a Soft Reset while holding the "volume down" key on the left side of the device. Keep holding the "volume down" key until you see tricolour screen which is the bootloader mode, then release it)
Flashing Via MicroSD Card
1. Make sure your microSD is Formatted to fat32 (you dont have to delete all files but it is safer if you do)
2. Download your prefered Rom from the Rhodium Rom Develpoment Page and unzip/unrar it to your PC
3. Goto the Roms Folder and rename the .nbh file to RHODIMG.nbh
4. Copy the RHODIMG.nbh file to the root of your MicroSD Card
5. Plug the MicroSD Card into the phone
6. Enter the BootLoader screen, you will first see a tri-color screen with the phone and SPL Information at the top
7. Follow the On Screen instructions to start the update
8. After flash has completed, press the reset button with the stylus to reset the device.
Good Luck ! Worked For me
i tried this option but didn't work, is there any help, the phone can't come up again
it show this Error msg at 0% "BOOTLOADER - FAIL" update terminated
Click to expand...
Click to collapse
larryike said:
i tried this option but didn't work, is there any help, the phone can't come up again
it show this Error msg at 0% "BOOTLOADER - FAIL" update terminated
Click to expand...
Click to collapse
\
Did you try the stock rom from HTC loaded over the usb first?
Information about what unlocker you tried to use, what kind of phone you have, what kind of rom you tried to load would be helpful.
Hello,
I tried to flash my diamond (GSM) and everthing went well until when I was doing the MTTY procedure. At the final step (after the disconnecting usb and holding down + back) it blocked on a loading message and stayed ther for 20 min. when I reseted it it failed to pass the htc logo. I can still enter boot loader menu (Hard SPL 1.30 Oilnex) Can Anybody help?
after doing mtty procedure, you need to reflash again..
Already tried that but doesn't work...
If you can go to boot loader then you are laughing...
Plug in your device....it should go from serial to USB.
Then load the rom of choice via RUU_exe.
Keep me posted....
Hi all u guys out there hope someone can help me i installed this rom on my diamond the name was TEAL or some like that the first few times it was fine but then my battery was running low and then when i turned my diamond on again i had 2 setup mobile and now it just keep showing the screen that says it wanna setup and i cant acess USB from there so plz if u can help me recover my diamond plz reply
try update from Boot Screen
Blackster..try updatin frm boot screen..go in boot screen & then connect it to usb & try updatin the ROM...
to get in your bootscreen just reset your device while holding the volume down button
just so you know ^^
Tried every thing
,My vista wont show the usb from hardSPL and i cant connect from the setup and when i just installed the rom again it wont work
nothings work plz help
USB??
its just installing the usb driver but show no usb
simple thing
just run RUU from u'r PC...
Follow 1st Two steps by clicking next...
no need to perform mentioned task in RUU.
Connect USB Cable PC to Diamond...
On diamond hold on off button and volume down button and hit reset button on back..
you will forwarded to boot screen on diamond...
It will automaticly identify u'r USB connection to PC...
Once it displays USB on diamond boot menu, Hit Update button on RUU running on PC...
Then follow the RUU instructions...
Once finished, you have done...