My Xdaexec not connecting to PC in bootloader mode. While I was uograding the rom, the computer shutdown. And did not finish th upgrade. Please can any one help me how to solve this problem. Tanks a lot.
when you plug in the usb, the bootloader screen should show 'usb', your pc will not show anything. start the ruu and it should work as normal
try 2 read wiki -how2 upgrade thru bootloader, try2 dwnld Uni_exit_bootloader.exe, mtty, but first if u are in bootloader flash again (and use ups for pc)
Related
i am tring to flash the imate jasjam rom i downloaded from imate website, i plug it in and activesync connects, but when i get to the "verifying information on pda" my pda goes into bootloader and then i get error 260 or something saying im not connected! please help!
any ideas?
Install Hard SPL V7 then use sd card method.
try this
put the phone into boot loader mode (power off press and hold comm button and ok buttons at same time and power on the device)
screen should say serial, plug in usb, screen should change to usb, then run the rom (ruu file) on your pc
reflash.. impossible
--------------------------------------------------------------------------------
hi guys, ive a strange problem.. after flashing mad's ita-rom in my hermes, as i retryed to flash another one it was not more possible.
in the beginning normal connex but before going in bl-mode...error and nada
active sync 4.5 AND 6.1 refused to reconnect to device.
i tryed to put manual in bootloader modus.. nothing happened.
well, i ve the sd card modus possibility but i want use this as last solution.
please need info, thx
what do you mean by "i tryed to put manual in bootloader modus.. nothing happened. "?
Did it enter bootloader? If so, don't look at ActiveSync, it won't show you anything, just run ruuwrapper and flash your baby
hmm?
yes, it enter in bootloader modus, but if i try to run wrapper, same error than without..
active sync stay connected until arriving to verify the device.. after that.. error coz cable unplugged or not correct connected..
HTC_BALI said:
yes, it enter in bootloader modus, but if i try to run wrapper, same error than without..
active sync stay connected until arriving to verify the device.. after that.. error coz cable unplugged or not correct connected..
Click to expand...
Click to collapse
The same error happened to me quite often.
use the SD card method, its way better.
rename the .nbh file to hermimg.nbh and put it on a smaller than 2 Gb SD card formated to Fat32, then enter bootloader (power, ok, reset) and wait till the device asks you to press power button to start upgrading.
i try
oki, i will try it and let you know.. btw... jade is FANTASTIC...
never a problem after flashing with olinex hard spl..
thanks for the help..
i bring him in bootloader, but stucks there.. what now?
Hello,
I tried to flash my diamond (GSM) and everthing went well until when I was doing the MTTY procedure. At the final step (after the disconnecting usb and holding down + back) it blocked on a loading message and stayed ther for 20 min. when I reseted it it failed to pass the htc logo. I can still enter boot loader menu (Hard SPL 1.30 Oilnex) Can Anybody help?
after doing mtty procedure, you need to reflash again..
Already tried that but doesn't work...
If you can go to boot loader then you are laughing...
Plug in your device....it should go from serial to USB.
Then load the rom of choice via RUU_exe.
Keep me posted....
Hi all u guys out there hope someone can help me i installed this rom on my diamond the name was TEAL or some like that the first few times it was fine but then my battery was running low and then when i turned my diamond on again i had 2 setup mobile and now it just keep showing the screen that says it wanna setup and i cant acess USB from there so plz if u can help me recover my diamond plz reply
try update from Boot Screen
Blackster..try updatin frm boot screen..go in boot screen & then connect it to usb & try updatin the ROM...
to get in your bootscreen just reset your device while holding the volume down button
just so you know ^^
Tried every thing
,My vista wont show the usb from hardSPL and i cant connect from the setup and when i just installed the rom again it wont work
nothings work plz help
USB??
its just installing the usb driver but show no usb
simple thing
just run RUU from u'r PC...
Follow 1st Two steps by clicking next...
no need to perform mentioned task in RUU.
Connect USB Cable PC to Diamond...
On diamond hold on off button and volume down button and hit reset button on back..
you will forwarded to boot screen on diamond...
It will automaticly identify u'r USB connection to PC...
Once it displays USB on diamond boot menu, Hit Update button on RUU running on PC...
Then follow the RUU instructions...
Once finished, you have done...
hi ...and i know this is not the right section
i'v read thread here :
[Tutorial] Fix FOTA bricked (unlocked bootloader) Phones
and iv serious problem
i'v accidentaly press Repair TA in Octopus SE 1.0.9 when my wt19i was connected in flash mode (the green light mode)
after that my phone starts normaly but i can't put my phone in flash mode any more
what does repair TA do to my phone
and who can i fix it
i have a thread here :
http://forum.xda-developers.com/show....php?t=1466492
please can u help me
any help here
connect it with PC Compagnon, when is connect make repair , the phone reboot in flash mode . then you can flash with flashtools
Amivieu said:
connect it with PC Compagnon, when is connect make repair , the phone reboot in flash mode . then you can flash with flashtools
Click to expand...
Click to collapse
PC Companion always tolled me server over load
try agine later !!!!!
is there is a program restart my phone in flash mode ?
Take out battery, connect usb cable, hold back button and now plug in the battery and you should end up in flashmode.
Sent from my iPad 2 using Tapatalk