Help Brick - Touch Diamond, MDA Compact IV ROM Development

Hello,
I tried to flash my diamond (GSM) and everthing went well until when I was doing the MTTY procedure. At the final step (after the disconnecting usb and holding down + back) it blocked on a loading message and stayed ther for 20 min. when I reseted it it failed to pass the htc logo. I can still enter boot loader menu (Hard SPL 1.30 Oilnex) Can Anybody help?

after doing mtty procedure, you need to reflash again..

Already tried that but doesn't work...

If you can go to boot loader then you are laughing...
Plug in your device....it should go from serial to USB.
Then load the rom of choice via RUU_exe.
Keep me posted....

Related

XDA EXEC stuck at spalsh screen after flashing

Hai ,
I tried different flashes of WM6 , then i reverted back to wm5.
But then again i flashed it with wm6 rom.
It flashes it successfully but after hard reset , pressing 0 , it just stays at splash screen giving infos in red.
I am stuck at spalsh screen ... any ideas ?
Also tried uni_exitbootloader .. but still stucks at splash screen
Tried Refalshing it many times but same ..
babablacksheep said:
Hai ,
I tried different flashes of WM6 , then i reverted back to wm5.
But then again i flashed it with wm6 rom.
It flashes it successfully but after hard reset , pressing 0 , it just stays at splash screen giving infos in red.
I am stuck at spalsh screen ... any ideas ?
Also tried uni_exitbootloader .. but still stucks at splash screen
Tried Refalshing it many times but same ..
Click to expand...
Click to collapse
Try enter bootloader and re-flash WM6 Rom, if it still fails to boot, search the Universal forum for MTTY commands to reset partition tables. I suspect the partitions are corrupt.
Hope youre battery is not too low.
Cheers,
Beast
babablacksheep said:
Hai ,
I tried different flashes of WM6 , then i reverted back to wm5.
But then again i flashed it with wm6 rom.
It flashes it successfully but after hard reset , pressing 0 , it just stays at splash screen giving infos in red.
I am stuck at spalsh screen ... any ideas ?
Also tried uni_exitbootloader .. but still stucks at splash screen
Tried Refalshing it many times but same ..
Click to expand...
Click to collapse
Something like this happened to me when I first flashed my Universal, I tried something in the Wiki (Cannot remember?) That told me to use that usb port from now on for all flashing. After that it worked. I will search further to see if I can help...
Okie Problem Solved.
I did this to get myself sigh if relief.
100% working
1. Take out the SD and SIM cards
2. Opened ActiveSync and go to file, connection setting and Un-check "Allow USB Connections". Then press Ok and close ActiveSync
3. Put in bootloader mode (Power + Light + reset) which brings up the "un-backlit" screen with "Serial" at the top and v0.XX at the bottom
4. Plug in USB cable DIRECTLY from PC to Jasjar (MAKE SURE NOT TO USE A USB HUB). You MIGHT then see a warning window complaining that an "Unsigned" device driver is being attempted to be installed. You will be prompted to either "STOP INSTALLATION" or "CONTINUE ANYWAY" - this warning can be safely ignored and so just click on "CONTINUE ANYWAY".
5. Open mtty utility / software
6. Select USB from the "Port" drop-down on the upper left corner of the dialog box and hit OK
7. Then another screen will come up. Hit enter and that will show "USB>"
8. Type "task 28 55aa" and hit enter. {type it manually/ don`t copy and paste commands}
9. use the "Original OEM ROM" that is made for your device and update with it (CE,Extended and Radio) Flash all
10. Hard Reset
Also if your device bootloader version is lower than "v 1.01" you should update that first (before installing the OEM ROM, but NOT before "Task 28 55aa").
After this is complete you may then use your device again.
NOTe : I find you must kill the wcescomm, wcesmgr and rapimgr exe's using task manager before you get the 'usb' option in mtty (kills activesync)
Please,
what to do when there's no USB port in mtty (only COM1 and COM2) ?????
babablacksheep
must say -Thank you!
vjj said:
Please,
what to do when there's no USB port in mtty (only COM1 and COM2) ?????
Click to expand...
Click to collapse
You must disable ActiveSync before connection
and put in bootloader mode (Power + Light + reset) BEFORE run MTTY
after USB must appear in drop-down menu
one more time thanked babablacksheep

What to do when activesync does not work

i tried to upgrade to new kitchen image but it came up with activesync broken. now i want to revert to another image but does not know how this can be achieved.
is it possible to bring herm100 into SPLv bootloader and have it talk over USB so that a new image can be transferred?
Did you try a soft reset first, then test if you can get AS to connect, then try hard reset.
Do this while DISCONNECTED from the PC.
Sometimes after flashing a new OS, I have lost AS connectivity. A soft reset of the device, or a power cycle reboot always solved the problem.
i tried both soft and hard reset but it does not help. when it tries to activesync then it connects to "'USB" instead to "USB" - note ' before USB.
OK, you can enter bootloader and flash another image through the USB using the RUU.
slimshadee said:
OK, you can enter bootloader and flash another image through the USB using the RUU.
Click to expand...
Click to collapse
Right. Nice one slimshadee.
The other alternative is to flash using SD Card method.

wont update in bootloader?

i am tring to flash the imate jasjam rom i downloaded from imate website, i plug it in and activesync connects, but when i get to the "verifying information on pda" my pda goes into bootloader and then i get error 260 or something saying im not connected! please help!
any ideas?
Install Hard SPL V7 then use sd card method.
try this
put the phone into boot loader mode (power off press and hold comm button and ok buttons at same time and power on the device)
screen should say serial, plug in usb, screen should change to usb, then run the rom (ruu file) on your pc

I think i bricked my phone...please help!

Ok, so I have flashed a ton of ROMs, very successfully I might add. This last ROM I flashed worked just fine. After a day or so it started having some issues, so I tried to restart it. It started booting back up, and never left the HTC Innovation screen with the red text in the lower right hand corner.
I have hard reset it several times, and still I get the same thing. I can get to the boot loader screen and get it to change from serial to usb when plugging it into the computer, but this is as far as I get. Can someone please help me, thanks in advance!
Mark
PS I have also searched the forums, but unfortunately don't know quite what to search for. Thanks again!
Enter in the Bootloader mode (VolDown when reseting), plug the USB cable and install an older ROM via CustomRUU you know is working..
enter bootloader , use MTTY - http://forum.xda-developers.com/showthread.php?t=540290 to format rom memory .
Then flash it with a stock rom from www.HTC.com
Thanks
Thank you both for the help, trying now...IT WORKED!! Thank you guys so much!
Enter bootloader successfully means your phone is not bricked yet.
1) Use MTTY do delete old ROM
the command is "task 29"
Search the forum "MTTY" to learn how to use and where to download
2) Flash new ROM. Done
satus said:
Enter bootloader successfully means your phone is not bricked yet........
Click to expand...
Click to collapse
May not always be true !?
Here's output of 'TASK 29' (end section)
Flash NAND DM internal transfer failed: dmov_transfer()bad=0x7FF
R:NO bad block reversed for block ID 0x7FF
Read sector fail!!!
Can someone enlighten and lead ....
task 28!!! NOT 29!!
more precisley "task 28 55aa"
Dont typo the MTTY commands as it can completly screw up your phone...
please help after flashing a couple of roms i started having some problems
like everytime i reset it does a hard reset and now it doesn't seem to leave the boot image with TOUCH DIAMOND
i cant understand what steps i must follow for MTTY on xp
MTTY didn't work for me
I bricked my phone a few weeks ago and tried everything i could find on MTTY and nothing worked, error after error, i got really lucky and entered bootloader and plugged my USB in immediately after windows 7 boot up and got away with it through CustomRUU. 6 hours to fix and 25 minutes sleep before work. But hey, fixed the diamond and thats all that mattered.
MTTY + Latest HardSPL should solve any problems if you still have access to the bootloader

HELP PLZ!!!!! (rom fail ?)

Hi all u guys out there hope someone can help me i installed this rom on my diamond the name was TEAL or some like that the first few times it was fine but then my battery was running low and then when i turned my diamond on again i had 2 setup mobile and now it just keep showing the screen that says it wanna setup and i cant acess USB from there so plz if u can help me recover my diamond plz reply
try update from Boot Screen
Blackster..try updatin frm boot screen..go in boot screen & then connect it to usb & try updatin the ROM...
to get in your bootscreen just reset your device while holding the volume down button
just so you know ^^
Tried every thing
,My vista wont show the usb from hardSPL and i cant connect from the setup and when i just installed the rom again it wont work
nothings work plz help
USB??
its just installing the usb driver but show no usb
simple thing
just run RUU from u'r PC...
Follow 1st Two steps by clicking next...
no need to perform mentioned task in RUU.
Connect USB Cable PC to Diamond...
On diamond hold on off button and volume down button and hit reset button on back..
you will forwarded to boot screen on diamond...
It will automaticly identify u'r USB connection to PC...
Once it displays USB on diamond boot menu, Hit Update button on RUU running on PC...
Then follow the RUU instructions...
Once finished, you have done...

Categories

Resources