ROM upgrade failed !!! - Touch Pro2, Tilt 2 Windows Mobile General

Hi everybody,
I look through the threads and I couldn't find a solution to my troubles. So here it is: I just bought a htc touch pro 2 which came with a window mobile 6.1. Before I transferred anything from my old phone, I thought better to do the official upgrade to 6.5 ROM version 1.86.401.0.
I wanted to flash the ROM through a USB cable as described on the HTC site, but after after having done 22% of the work, everything got stuck. And 5' minutes afterward the update windows on the PC disappeared and I had to disconnect the phone!!!
So now I have a beatiful telephone, which cannot boot up. Indeed, it gets stuck in the 4 colors bootloader.
i) I tried to do a factory reset (pressing power, send hang up buttons) to no avail.
ii) I tried to take out the batteries and pull them in again, then switching on the phone holding down the vol down + power up buttons, then reset.
iii) reconnecting the phone back to the PC by usb, I was never able to get a switch from "serial" to "usb"
Nothing is working, if anybody has an idea what I could try next.... I am wondering if it is possible to flash the phone from the SD card. I am really a newbie here.
Thanks
Max

Yea .. same thing happened to me ..
Check Here For Full Info: Click Here
*Go into BootLoader Mode (do a Soft Reset while holding the "volume down" key on the left side of the device. Keep holding the "volume down" key until you see tricolour screen which is the bootloader mode, then release it)
Flashing Via MicroSD Card
1. Make sure your microSD is Formatted to fat32 (you dont have to delete all files but it is safer if you do)
2. Download your prefered Rom from the Rhodium Rom Develpoment Page and unzip/unrar it to your PC
3. Goto the Roms Folder and rename the .nbh file to RHODIMG.nbh
4. Copy the RHODIMG.nbh file to the root of your MicroSD Card
5. Plug the MicroSD Card into the phone
6. Enter the BootLoader screen, you will first see a tri-color screen with the phone and SPL Information at the top
7. Follow the On Screen instructions to start the update
8. After flash has completed, press the reset button with the stylus to reset the device.
Good Luck ! Worked For me !

Thanks for your help and the link to the thread!! I will use your approach next time. Indeed, in the day afterwards I was able to finally flash the phone from the same PC. I did the manipulation, which failed miserably, with a 64 bit Windows 7 RC. Then, I realised I had another version of W7 on the same PC, a 32 bit version this time. Thus, when I tried it with my dying telephone, the "serial" message on its screen switched "magically" to "usb" and I finally could flash the damned mobile! Frankly, I don't know what's wrong with my 64bit W7 if anything.
Cheers
Max

my htc pro2 failed upgrade: any help
WarlockW said:
Yea .. same thing happened to me ..
Check Here For Full Info: Click Here
*Go into BootLoader Mode (do a Soft Reset while holding the "volume down" key on the left side of the device. Keep holding the "volume down" key until you see tricolour screen which is the bootloader mode, then release it)
Flashing Via MicroSD Card
1. Make sure your microSD is Formatted to fat32 (you dont have to delete all files but it is safer if you do)
2. Download your prefered Rom from the Rhodium Rom Develpoment Page and unzip/unrar it to your PC
3. Goto the Roms Folder and rename the .nbh file to RHODIMG.nbh
4. Copy the RHODIMG.nbh file to the root of your MicroSD Card
5. Plug the MicroSD Card into the phone
6. Enter the BootLoader screen, you will first see a tri-color screen with the phone and SPL Information at the top
7. Follow the On Screen instructions to start the update
8. After flash has completed, press the reset button with the stylus to reset the device.
Good Luck ! Worked For me
i tried this option but didn't work, is there any help, the phone can't come up again
it show this Error msg at 0% "BOOTLOADER - FAIL" update terminated
Click to expand...
Click to collapse

larryike said:
i tried this option but didn't work, is there any help, the phone can't come up again
it show this Error msg at 0% "BOOTLOADER - FAIL" update terminated
Click to expand...
Click to collapse
\
Did you try the stock rom from HTC loaded over the usb first?
Information about what unlocker you tried to use, what kind of phone you have, what kind of rom you tried to load would be helpful.

Related

Can't get to bootloader!

When ever I try to get to bootloader mode, my phone just comes up to the tri-color screen. I press and hold the left OK key along with the power button, then do a soft reset. I only get to the tri-color screen. Can someone help me out with this please...I'm trying to upgrade to a WM6.1 rom on my 8525 via SD card.
1jaxstate1 said:
When ever I try to get to bootloader mode, my phone just comes up to the tri-color screen.
Click to expand...
Click to collapse
the tri-color screen is the bootloader. (read the wiki)
wfg
starbase64
1jaxstate1 said:
When ever I try to get to bootloader mode, my phone just comes up to the tri-color screen. I press and hold the left OK key along with the power button, then do a soft reset. I only get to the tri-color screen. Can someone help me out with this please...I'm trying to upgrade to a WM6.1 rom on my 8525 via SD card.
Click to expand...
Click to collapse
The tri-color screen IS the bootloader. I have found with my 8525, that if you turn the device off (power button for 5 seconds, then tap OK), all you need do is hold the side OK and the power button together for a few seconds. No need to find the reset hole if the device is OFF.
If you have an SD card in the device (with a copy of HERMIMG.NBH on it), the Tri-Color screen will come up, searching the card. When the NBH file has been found, it will show you the various parts that the file includes, and prompt you to press the power button to begin.
It's really easy this way. I rarely flash through USB anymore.
Hope this helps,
-pvs
Wow..thanks for the speedy response. I'll give it a try. Thanks again.
When I try to upgrade via SD, the bootloader never reads the SD card, it just sits...and says serial at the bottom of the screen.
When I try to upgrade via USB, after I start the RUU, the active sync connection is broken, and the phone goes into the bootloader screen and just sits...and says USB at the bottom of the screen.
If anyone has had this problem, please let me know. If not..I guess I'll just have to go out and buy a Tilt.
Current ROM: 2.15.502.3
Current Radio: 1.40.30.00
SUCCESS!!!!
Thanks for your help. My company has the firewall on and it, for some reason was killing my active sync connection. I was able to upgrade via USB. And this ROM is looking great starbase64
1jaxstate1 said:
When I try to upgrade via SD, the bootloader never reads the SD card, it just sits...and says serial at the bottom of the screen.
Click to expand...
Click to collapse
1) Is your SD card freshly formatted (FAT32)?
2) have you installed HardSPL? If not, do it.
3) Are you sure you spelled the name of the NBH correctly? HERMIMG.NBH
4) Copy HERMIMG.NBH to the root of your SD card
5) Shut off the device (power off all the way)
6) Insert the SD card with only the one file (HERMIMG.NBH) on it
7) Press the side OK button and the power button simultaneously for a couple of seconds
8) your device should start up, and the bootloader will look for the HERMIMG.NBH file
9) If all the above is done corectly, your device SHOULD find the NBH and tell you what parts it contains, then ask you if you wish to proceed, by pressing the power key. If this isn't happening for you, I'm afraid I don't have any other suggestions for you.
1jaxstate1 said:
When I try to upgrade via USB, after I start the RUU, the active sync connection is broken, and the phone goes into the bootloader screen and just sits...and says USB at the bottom of the screen.
If anyone has had this problem, please let me know.
Click to expand...
Click to collapse
Others HAVE had this problem. You need to disable one of the settings in ActiveSync, but I don't remember which one. Try doing a search under the main HERMES forum, including all subforums. This is one of those questions that gets asked a lot, so be prepared to sift through all the repetitive threads (GOD, if only people would SEARCH first!).
1jaxstate1 said:
If not..I guess I'll just have to go out and buy a Tilt.
Click to expand...
Click to collapse
You might want to read THIS, first
Good luck,
-pvs
when you say copy the .nbh file to the root of the SD card what exactly do you mean. When i put the SD card in there and format it its completely empty with nothing there, then the only option i have is open the SD card folder and put it in there, is that correct?
okay so i just did the SD card flashing, said on the screen it was flashing and did the whole thing fine. Told me it was complete so i pressed the power the button to restart the phone and no matter how many times i restart the phone it just boots into Tri color screen and says serial at the bottom.
I tried soft reset and removing the battery no matter how many times i do it, always comes back to Tri color screen.. help!
ahhhhwhoa said:
okay so i just did the SD card flashing, said on the screen it was flashing and did the whole thing fine. Told me it was complete so i pressed the power the button to restart the phone and no matter how many times i restart the phone it just boots into Tri color screen and says serial at the bottom.
I tried soft reset and removing the battery no matter how many times i do it, always comes back to Tri color screen.. help!
Click to expand...
Click to collapse
Hmmm, I typically do a RESET after the flash process completes. Never tried shutting down using the power button. So now your device is stuck in BL? I'm not sure of the procedures you need to try to escape that one, but I KNOW it's been discussed here in the forums. You MIGHT try flashing a different ROM. It might be the simplest way to recover. If that doesn't work, you might want to check the Wiki HERE.
Good luck!
-pvs

How to flash if activesync won't work

I can't get my Diamond to talk to activesync on two machines (one of which it used to be fine with). Given that, is it possible to flash it? What's the procedure?
Kallisti said:
I can't get my Diamond to talk to activesync on two machines (one of which it used to be fine with). Given that, is it possible to flash it? What's the procedure?
Click to expand...
Click to collapse
look in my sig
...
enter bootloader and plugin to pc. and pray it got detected as mobile device in device manager. if it does, run ruu.
if not, here's a work around.... turn on phone. go to setting > connection > usb to pc > and change to connect as storage device.
plugin to pc and copy .nbh file of your choice to internal storage (rename .nbh file to diamimg.nbh) (which will be most likely detected as a usb drive)
use stylus and reset phone. hold vol down and back button.... you'll be in bootloader and soon a screen will pop up "triggering movinand bla bla bla..."
press power button to start flashing. when done, use stylus to reset again, now press vol down and circle.
hard reset device > press vol up to continue.
wait for device to self customize.
by the way, this might not work.
Brilliant - updating it now. Thanks guys

[Q] bricked tilt 2

help please!
i preformed task 29 on my tilt 2 and i now have an ATT screen and wont go any further. when i try to stat it it only goes as far as the first screen and no further. i tried resting it to no avail. i can not establish connection with pc. i have vista for pc. can somebody help please?
Yes. now u preformed that, you want to plug in your USB. Push reset and the lower volum button at the same time. You will go into boot loader mode. It should say USB on the bottom once u have made a connection after connecting your USB to the computer. At that point flash your Radio, after flashing your radio, flash your rom. All like you normaly would ..
PS. make sure Sim and MScard is out of phone before preforming Flashing Radio, then the rom. Then replace the sim card after all the installation from the rom you are installing..
First go back to the task 29 post and read all the instructions.
Task 29 is a memory wiper,it completely wipes the memory of the device leaving only the radio and basic functions.
To get up and running again follow these instructions:
1. Download the newest stock rom for ATT found in the Rom Development forum. http://forum.xda-developers.com/showthread.php?t=737168
2. Remove back cover from the device, remove the battery, remove the SIM card and remove the SD card if you have one. Reinstall the battery, do not replace the back cover.
3. Power up the device and connect it to the PC. Press the down volume button and press and hold the stylus into the reset button, hold both until the boot screen appears. Windows may install some software at this time, let the software install.
4. When USB appears at the bottom of the boot screen run the ROM installer software run. Follow ALL on screen instructions.
NOTE: If you have Hard SPL installed you can install any custom ROM, if not you MUST install a STOCK SHIPPED ROM.
twh said:
help please!
i preformed task 29 on my tilt 2 and i now have an ATT screen and wont go any further. when i try to stat it it only goes as far as the first screen and no further. i tried resting it to no avail. i can not establish connection with pc. i have vista for pc. can somebody help please?
Click to expand...
Click to collapse
First of all check to see if your phone is hardspl'ed by turning phone completely off then hold volume down key then power phone back on from here you should be on tri-color screen see what the spl version says if it says 0.85Olinex it's hardspl'ed anything else is not hardspl'ed.
If your phone is hardspl'ed then your good all task29 does is wipe your entire os off your phone thats why it won't boot to nothing but the startup screen so in order for it to boot you need to flash a rom on to it, so like before power phone off hold volume down key & power phone on you should be on tri-color screen again at the bottom of phone screen it should say serial now plug in usb from computer now it should say usb at the bottom of phone find a rom that you like then flash it phone should reboot after flash & work like normal once again.
Hope this helps
thank you all you guys. you all were awesome. as you could imagine, i am new to wm. but with the help of every body, i got my phone up and running.
twh said:
thank you all you guys. you all were awesome. as you could imagine, i am new to wm. but with the help of every body, i got my phone up and running.
Click to expand...
Click to collapse
no problem i'm glad we all were able to help you

[Q] Can I flash a windows mobile rom to a tilt 8925 that currently has android

I am trying to flash a windows mobile rom to my tilt 8925 that currently has android on it. It is not working, and android has to many glitches and is taking to much of my time, rendering it not worth it. The problem I run into in the flash process is when the phone has to be connected to active synce, it will not connect. Is there a way to get around this and get windows mobile back. Thanks for your help in advance
Mrpcgeekman
If i understand, you can't flash Windows Mobile ROM on your phone ( which currently have Android ), right? ...and You tried Active Sync method with CustomKaiserRUU.exe or something like that ( flashing over USB )?
...anyway...seek for .NBH WinMO ROM file, put on your SD Card (phone is switched off!). Push CAMERA button and POWER button <hold them> and wait for tri-color screen (You will get same dialog as for flashing kernel), follow instructions <it will say to push power button to flash .nbh>, wait for process to finish...it will last a bit longer, cause .nbh WinMoROM is big file. Soft reset...and voila...
Yes, you can re-flash Windows Mobile back onto your Tilt that has Android.
Best bet is too get the original ROM from HTC, and flash that back on your phone before flashing a custom WinMo ROM.
No doubtedly you have HardSPL loaded, which means you can flash WinMo using the SD Card method.
Just take the ROM, and rename the RUU_signed.nbh to KAISIMG.NBH, and transfer it to the root of your SD Card. Boot the phone by pressing CAMERA + POWER button at the same time to boot the phone into the Tri-Color screen. Then the phone will automatically go to a grey screen with a "Loading ...." text, wait until you see it saying "KAISIMG.nbh - ". Press Power button to begin flashing, and I'd recommend it being plugged into A/C power while this is going, as it will take a bit to complete.
You will see it flashing a new Boot Loader, don't worry as long as you don't include KAISDIAG.NBH, your HardSPL will not be overwritten.

[Q] S4 mini does not boot into recovery mode after attempt to root

Hi.
I have followed the instructions on this thread to root the GT-I9190 but I am stacked on Step 7.
The procedure is as:
Copy the "S4Mini_RootKit_v2.zip" to your device SD card.
Turn off the phone.
Press and hold home, volume down and power. Download screen should appear.
Connect USB cable, and press volume up.
Start Odin, uncheck "F. Reset Time", and then click AP button.
Select "recovery-clockwork-6.0.4.6-serrano3gxx.tar.md5" file that you previously extracted, and press Start button. The phone will reboot when finished.
After the phone resets (it vibrates) IMMEDIATELY hold volume up and home buttons to boot into recovery mode.
Select the option to install the ZIP file you have previously copied to your device and begin flashing it.
After flashing using CWM, reboot into system and enjoy your rooted device.
Click to expand...
Click to collapse
The phone does not boot into recovery mode. I have tried several times to press hold volume up and home buttons immediately after the phone vibrates when re-starting, but the phone just starts normally.
The phone applications cannot access the SD card to save files. When I try to save a file (from Internet or Titanium Backup) it says "No SD card present".
I can access the card from the file explorer and I access to pictures, music, etc. But the applications cannot find the SD card when they have to save a file.
- Should I go to step-8 and run "S4Mini_RootKit_v2.zip" from the SD card?
I will appreciate some help.
Thank You
ps: I am sorry for asking again. I am not receiving answers at the section for developers, so I have decided to ask at this section of Help & Troubleshooting
pingfloid said:
Hi.
I have followed the instructions on this thread to root the GT-I9190 but I am stacked on Step 7.
The phone does not boot into recovery mode. I have tried several times to press hold volume up and home buttons immediately after the phone vibrates when re-starting, but the phone just starts normally.
The phone applications cannot access the SD card to save files. When I try to save a file (from Internet or Titanium Backup) it says "No SD card present".
I can access the card from the file explorer and I access to pictures, music, etc. But the applications cannot find the SD card when they have to save a file.
- Should I go to step-8 and run "S4Mini_RootKit_v2.zip" from the SD card?
I will appreciate some help.
Thank You
ps: I am sorry for asking again. I am not receiving answers at the section for developers, so I have decided to ask at this section of Help & Troubleshooting
Click to expand...
Click to collapse
Switch the phone off, than press power+vol up+menu simultaneously, when the phone vibrate (powering on), let go. If it doesn't enter recovery you not doing it right, there's no other answer to that.
As for phone not reading SD card, what type of SD card is't?
TNCS said:
Switch the phone off, than press power+vol up+menu simultaneously, when the phone vibrate (powering on), let go. If it doesn't enter recovery you not doing it right, there's no other answer to that.
As for phone not reading SD card, what type of SD card is't?
Click to expand...
Click to collapse
Thank you!!
As I understood the instructions, I was pressing power+vol up+menu AFTER the phone vibrates, but you made it clear that it is before.
So simple, but since It is the first time I do this, I didn't want to experiment
pingfloid said:
Thank you!!
As I understood the instructions, I was pressing power+vol up+menu AFTER the phone vibrates, but you made it clear that it is before.
So simple, but since It is the first time I do this, I didn't want to experiment
Click to expand...
Click to collapse
No problem. Not to worry, no harm can be done by trying to enter the recovery mode, either than you may 1. Drain a lot of battery or 2. wipe user data which is like a factory reset.
Please press the 'Thanks' button if I helped in any way.
Hello Frends i took TWRP for s4 mini but now I cannot boot to recovery and also to download mode Please help me.. step by step
My s4 mini restart with logo &doesnt enter recovery mode,pls hlp

Categories

Resources