Help about upgrading to wm6.1 - JASJAR, XDA Exec, MDA Pro Software Upgrading

Hi i just bought a i-mate jasjar, it's a g3 device (boot shows 1.01). i just flashed ranju's rom but it freezes on wm6 splashscreen and i dont know what to do, help me please i want a wm6-6.1 ROM!!! thank you so much...

I had the same thing recently caused by not unticking allow USB connection in activesync. I tried to do it 3 times before I realsed what the problem was. I had to use MITY to reset the unit then reflashed the ROM & it was OK.

ken0150 said:
Hi i just bought a i-mate jasjar, it's a g3 device (boot shows 1.01). i just flashed ranju's rom but it freezes on wm6 splashscreen and i dont know what to do, help me please i want a wm6-6.1 ROM!!! thank you so much...
Click to expand...
Click to collapse
read the wiki, you will find all you need to instal roms with no problem
Cheers

Solution
keno0115 it was exactly my case. Here is how I solved:
First flash it back to original jasjar rom (WM5). But to do so:
1- Unhook your jasjar from your computer
2- Untick "USB Connection" in ActiveSync
3- Press light button+power button+reset button to go to bootloader mode
4- plug-in usb cable to hook up to the computer
5- Run JasJar Rom update as usual
6- Hard reset your jasjar to see WM5 is working fine
Then flash it to ranjus rom. To do so:
1- Download http://rapidshare.com/files/36286892/UNI_upgrade_issues_and_solutions.rar
2- Extract Country_Id_Error folder under Rom Unlock folder
3- Extract Ranjus's rom (or any other WM5 or 6 or 6.1 rom) to a folder
4- Copy nk.nbf to the extracted Country_Id_Error folder (step2)
5- Unhook your jasjar from your computer
6- Untick "USB Connection" in ActiveSync
7- Press light button+power button+reset button to go to bootloader mode
8- plug-in usb cable to hook up to the computer
9- Run MaUpgradeUt_noID.exe from Country_Id_Error folder
10- After flashing finished do a hard reset. And wait 2 or so minutes to calibration screen come up.
11- Tick back again "USB connection" in ActiveSync, to use activesync again
Hope that helps.
alpusm

Related

XDA EXEC stuck at spalsh screen after flashing

Hai ,
I tried different flashes of WM6 , then i reverted back to wm5.
But then again i flashed it with wm6 rom.
It flashes it successfully but after hard reset , pressing 0 , it just stays at splash screen giving infos in red.
I am stuck at spalsh screen ... any ideas ?
Also tried uni_exitbootloader .. but still stucks at splash screen
Tried Refalshing it many times but same ..
babablacksheep said:
Hai ,
I tried different flashes of WM6 , then i reverted back to wm5.
But then again i flashed it with wm6 rom.
It flashes it successfully but after hard reset , pressing 0 , it just stays at splash screen giving infos in red.
I am stuck at spalsh screen ... any ideas ?
Also tried uni_exitbootloader .. but still stucks at splash screen
Tried Refalshing it many times but same ..
Click to expand...
Click to collapse
Try enter bootloader and re-flash WM6 Rom, if it still fails to boot, search the Universal forum for MTTY commands to reset partition tables. I suspect the partitions are corrupt.
Hope youre battery is not too low.
Cheers,
Beast
babablacksheep said:
Hai ,
I tried different flashes of WM6 , then i reverted back to wm5.
But then again i flashed it with wm6 rom.
It flashes it successfully but after hard reset , pressing 0 , it just stays at splash screen giving infos in red.
I am stuck at spalsh screen ... any ideas ?
Also tried uni_exitbootloader .. but still stucks at splash screen
Tried Refalshing it many times but same ..
Click to expand...
Click to collapse
Something like this happened to me when I first flashed my Universal, I tried something in the Wiki (Cannot remember?) That told me to use that usb port from now on for all flashing. After that it worked. I will search further to see if I can help...
Okie Problem Solved.
I did this to get myself sigh if relief.
100% working
1. Take out the SD and SIM cards
2. Opened ActiveSync and go to file, connection setting and Un-check "Allow USB Connections". Then press Ok and close ActiveSync
3. Put in bootloader mode (Power + Light + reset) which brings up the "un-backlit" screen with "Serial" at the top and v0.XX at the bottom
4. Plug in USB cable DIRECTLY from PC to Jasjar (MAKE SURE NOT TO USE A USB HUB). You MIGHT then see a warning window complaining that an "Unsigned" device driver is being attempted to be installed. You will be prompted to either "STOP INSTALLATION" or "CONTINUE ANYWAY" - this warning can be safely ignored and so just click on "CONTINUE ANYWAY".
5. Open mtty utility / software
6. Select USB from the "Port" drop-down on the upper left corner of the dialog box and hit OK
7. Then another screen will come up. Hit enter and that will show "USB>"
8. Type "task 28 55aa" and hit enter. {type it manually/ don`t copy and paste commands}
9. use the "Original OEM ROM" that is made for your device and update with it (CE,Extended and Radio) Flash all
10. Hard Reset
Also if your device bootloader version is lower than "v 1.01" you should update that first (before installing the OEM ROM, but NOT before "Task 28 55aa").
After this is complete you may then use your device again.
NOTe : I find you must kill the wcescomm, wcesmgr and rapimgr exe's using task manager before you get the 'usb' option in mtty (kills activesync)
Please,
what to do when there's no USB port in mtty (only COM1 and COM2) ?????
babablacksheep
must say -Thank you!
vjj said:
Please,
what to do when there's no USB port in mtty (only COM1 and COM2) ?????
Click to expand...
Click to collapse
You must disable ActiveSync before connection
and put in bootloader mode (Power + Light + reset) BEFORE run MTTY
after USB must appear in drop-down menu
one more time thanked babablacksheep

wont update in bootloader?

i am tring to flash the imate jasjam rom i downloaded from imate website, i plug it in and activesync connects, but when i get to the "verifying information on pda" my pda goes into bootloader and then i get error 260 or something saying im not connected! please help!
any ideas?
Install Hard SPL V7 then use sd card method.
try this
put the phone into boot loader mode (power off press and hold comm button and ok buttons at same time and power on the device)
screen should say serial, plug in usb, screen should change to usb, then run the rom (ruu file) on your pc

ROM upgrade failed !!!

Hi everybody,
I look through the threads and I couldn't find a solution to my troubles. So here it is: I just bought a htc touch pro 2 which came with a window mobile 6.1. Before I transferred anything from my old phone, I thought better to do the official upgrade to 6.5 ROM version 1.86.401.0.
I wanted to flash the ROM through a USB cable as described on the HTC site, but after after having done 22% of the work, everything got stuck. And 5' minutes afterward the update windows on the PC disappeared and I had to disconnect the phone!!!
So now I have a beatiful telephone, which cannot boot up. Indeed, it gets stuck in the 4 colors bootloader.
i) I tried to do a factory reset (pressing power, send hang up buttons) to no avail.
ii) I tried to take out the batteries and pull them in again, then switching on the phone holding down the vol down + power up buttons, then reset.
iii) reconnecting the phone back to the PC by usb, I was never able to get a switch from "serial" to "usb"
Nothing is working, if anybody has an idea what I could try next.... I am wondering if it is possible to flash the phone from the SD card. I am really a newbie here.
Thanks
Max
Yea .. same thing happened to me ..
Check Here For Full Info: Click Here
*Go into BootLoader Mode (do a Soft Reset while holding the "volume down" key on the left side of the device. Keep holding the "volume down" key until you see tricolour screen which is the bootloader mode, then release it)
Flashing Via MicroSD Card
1. Make sure your microSD is Formatted to fat32 (you dont have to delete all files but it is safer if you do)
2. Download your prefered Rom from the Rhodium Rom Develpoment Page and unzip/unrar it to your PC
3. Goto the Roms Folder and rename the .nbh file to RHODIMG.nbh
4. Copy the RHODIMG.nbh file to the root of your MicroSD Card
5. Plug the MicroSD Card into the phone
6. Enter the BootLoader screen, you will first see a tri-color screen with the phone and SPL Information at the top
7. Follow the On Screen instructions to start the update
8. After flash has completed, press the reset button with the stylus to reset the device.
Good Luck ! Worked For me !
Thanks for your help and the link to the thread!! I will use your approach next time. Indeed, in the day afterwards I was able to finally flash the phone from the same PC. I did the manipulation, which failed miserably, with a 64 bit Windows 7 RC. Then, I realised I had another version of W7 on the same PC, a 32 bit version this time. Thus, when I tried it with my dying telephone, the "serial" message on its screen switched "magically" to "usb" and I finally could flash the damned mobile! Frankly, I don't know what's wrong with my 64bit W7 if anything.
Cheers
Max
my htc pro2 failed upgrade: any help
WarlockW said:
Yea .. same thing happened to me ..
Check Here For Full Info: Click Here
*Go into BootLoader Mode (do a Soft Reset while holding the "volume down" key on the left side of the device. Keep holding the "volume down" key until you see tricolour screen which is the bootloader mode, then release it)
Flashing Via MicroSD Card
1. Make sure your microSD is Formatted to fat32 (you dont have to delete all files but it is safer if you do)
2. Download your prefered Rom from the Rhodium Rom Develpoment Page and unzip/unrar it to your PC
3. Goto the Roms Folder and rename the .nbh file to RHODIMG.nbh
4. Copy the RHODIMG.nbh file to the root of your MicroSD Card
5. Plug the MicroSD Card into the phone
6. Enter the BootLoader screen, you will first see a tri-color screen with the phone and SPL Information at the top
7. Follow the On Screen instructions to start the update
8. After flash has completed, press the reset button with the stylus to reset the device.
Good Luck ! Worked For me
i tried this option but didn't work, is there any help, the phone can't come up again
it show this Error msg at 0% "BOOTLOADER - FAIL" update terminated
Click to expand...
Click to collapse
larryike said:
i tried this option but didn't work, is there any help, the phone can't come up again
it show this Error msg at 0% "BOOTLOADER - FAIL" update terminated
Click to expand...
Click to collapse
\
Did you try the stock rom from HTC loaded over the usb first?
Information about what unlocker you tried to use, what kind of phone you have, what kind of rom you tried to load would be helpful.

HELP PLZ!!!!! (rom fail ?)

Hi all u guys out there hope someone can help me i installed this rom on my diamond the name was TEAL or some like that the first few times it was fine but then my battery was running low and then when i turned my diamond on again i had 2 setup mobile and now it just keep showing the screen that says it wanna setup and i cant acess USB from there so plz if u can help me recover my diamond plz reply
try update from Boot Screen
Blackster..try updatin frm boot screen..go in boot screen & then connect it to usb & try updatin the ROM...
to get in your bootscreen just reset your device while holding the volume down button
just so you know ^^
Tried every thing
,My vista wont show the usb from hardSPL and i cant connect from the setup and when i just installed the rom again it wont work
nothings work plz help
USB??
its just installing the usb driver but show no usb
simple thing
just run RUU from u'r PC...
Follow 1st Two steps by clicking next...
no need to perform mentioned task in RUU.
Connect USB Cable PC to Diamond...
On diamond hold on off button and volume down button and hit reset button on back..
you will forwarded to boot screen on diamond...
It will automaticly identify u'r USB connection to PC...
Once it displays USB on diamond boot menu, Hit Update button on RUU running on PC...
Then follow the RUU instructions...
Once finished, you have done...

Ciphone C6+ WM 6.1 Rom/WM 6.5 Rom + Instruction

Hi pals,
I spend many days to find right rom for Ciphone C6+ and the right instruction for flashing him.
Now i will share with you everything what i found.
Rom can download from here:
WM 6.1 ENGLISH
WM 6.5 ENGLISH big thanks to dmitryxxl
Flashig tool can download from here:
IDT
Instruction:
1.Turn off your phone then press simultaneously “Power key”, “Volume Up” & “Home Key” to switch the phone
to “Download Mode”.
2. Download and install IDT
3. Launch IDT. At the prompt type 'hisilicon' as the password
4. Uncheck VerifyVer box
5. Browse for Image File by pressing '...' and point it to the .bin file that you want to upgrade to , press OK , IDT will ask you to select a platform , select GSM/EGPRS before you press OK ,
6.Connect ciphone via usb to pc , Your computer will install the necessary drivers for USB mode , then press OK buton and IDT will flash your phone.
If USB Drivers not installed automaticly from your PC you must do that manually.
USB Driviers are in C:\Program Files\HiSilicon\IDT\USB generic serial , just show from where must instal them your PC
good version ?
Hi,
I'm french, sorry for my bad english...
I bought a ciphone C6 with a ciphone-4gs processor. there is wm 6.1.
Do you think i can update it with this ROM 6.5 english ..
Best regards
I have tried flash de rom but the program stopped while it was updating… now i can’t put the mobile in dowload mode its only show a black screen. What can i do to put the ‘donwload mode’ screen again??
Hi! Sorry for my bad english...
I have a problem...unfortunately i install c6S rom my c6A phone, so black screen, no download mode
So what can i do to put the donwload mode again??
Thanks the answers

Categories

Resources