hello, first of all i am sorry if this is in the wrong section. you may move topic if you wish. please help.
i was just doing the spv m5000 new upgrade today when my computer just went off in the middle of the setup and now my SPV m5000 displays only to things without the backlight displays (serial and v1.00 when not connected to computer and USB and v1.00 when connected via usb. PLUS NO activeSYNC connection.
I have tryed hard reset but does not work screen comes saying press 0 to hard reset with the back light but nothing happens.
Please help i have just recently got this phone from ebay for over $350.00
Related
While upgrading my XDAII to the new O2 rom, I got a connection error which tiole me to disconnect the xda and do a soft reset.
I did this and it's now stuck on the O2 boot screen and wont budge, wont connect via active sync and does nothing else when I hard reset.
Have I f**ked it up ??
Please help,
Tommy
Don't panic
Just reset the device, place it back in the cradle and re-run the upgrade. It doesn't require Activesync as the upgrade process looks after its own connection.
Make sure the cradle is connected directly into a USB port on your PC and not to a hub. Also make sure the power supply is connected to the cradle.
Thanks, but that doesnt seem to help, the program just says that their is no connection.
Do you have another PC you can use? or try using a different USB port.
tried it on both and nothing, It looks like the XDAII can't start up properly and that's why it can't establish a connection. As I said it's stuck on the O2 boot screen (the one with the bubbles on it) with the version nos at the bottom and does nowt else.
I feel sick...
Tommy
OK. I misunderstood. I thought you were in the bootloader screen. So you need to see if you can put the device into bootloader mode. Press the jog button (bottom middle front of device) and power button at same time whilst pressing the reset button. This (hopefully) will put you in the bootloader - a dark screen with Serial 1.xx displayed. Then when device is put in cradle it should change to USB 1.xx. Then you can re-run the upgrade.
Whayhey
DCS you are indeed the man!
Thanks for your help.
Tommy
Dear All,
I've a problemi with my SPV M5000. After firmware upgrade, my device is stay in USB or Serial mode. I try hot and cold reset but no result? after few seconds it's back to USB or Serial Mode?
So, please help me!
I assume when you say you have hard reset the phone you have held in both soft keys and pressed the reset button? If so, I would flash the phone again, something probably went wrong.
Fin
Re ...
So the set is show only:
Serial on top on the screen and v1.00 on bottom of the screen.
When I connect USB cable is show:
USB on top on the screen and v1.00 on bottom of the screen.
After hot and cold reset this message is back?
Hi.
Think I have a real problem. My xda2 is in bootloader mode ready to be re-rommed, but my activesync (3.7) will not register that xda2 is connected. Tried loads of times re-installing activesync (different versions) with no joy at all. xda2 just sat there with dark screen waiting for rom. Please help.
heloo
I am currently upgrading my XDAIIs from WM2003 to WM6.5.
after checking the system from my XDAIIs, suddenly the power led went off and the sync is disconnected so I cannot continue the upgrade. On my phone screen there are only gray screen with USB at the top and V.2.07 at the bottom.
I have tried to restart the upgrading process but the problem is now my phone cannot connected to my laptop although I am using USB. I also tried to change the usb port and sync with other computer, but the problem is still the same.
FYI : at the beginning of the upgrade process, I didn't hard reset the phone. Is this the cause of the problem??
Please help me, does anyone have any solutions?
your device is in bootloader mode and it should show up as a ms_wm_device in
windows and you should be able to flash it again you can read more here
http://wiki.xda-developers.com/index.php?pagename=HTC_Blueangel
chanxda... you sorted it yet! I had same problem last nite and figured it out. Ill watch thread if you need reply!
Hi every one,
i have a serious problem with my HTC I-MATE JASJAR what's blocked in white screen (Serial / USB) and i cannot do anything on it, no boot, no reset soft, no reset Hard, no upgrade.
The issue is related to:
I tried to upgrade Radio ROM from 1.09.00 to 1.12 and i'm using Windows 7 Pro and when starting Flash, my PC shutdown because an electrical issue and since that, i cannot boot my device, i cannot flash or reset, my device is hung on white screen with Serial when no USB cable bluged in the PC and USB when Cable is pluged.
I Tried many times to boot it but no response, it's still hung and nothing can move on it.
I Just have one detail: when i plug the USB cable in my PC, the device is reconised but when starting upgrade or flash, i have error 101, no connexion.
Plz someone help me :crying::crying::crying::crying::crying::crying: