Dear All,
I've a problemi with my SPV M5000. After firmware upgrade, my device is stay in USB or Serial mode. I try hot and cold reset but no result? after few seconds it's back to USB or Serial Mode?
So, please help me!
I assume when you say you have hard reset the phone you have held in both soft keys and pressed the reset button? If so, I would flash the phone again, something probably went wrong.
Fin
Re ...
So the set is show only:
Serial on top on the screen and v1.00 on bottom of the screen.
When I connect USB cable is show:
USB on top on the screen and v1.00 on bottom of the screen.
After hot and cold reset this message is back?
Related
While upgrading my XDAII to the new O2 rom, I got a connection error which tiole me to disconnect the xda and do a soft reset.
I did this and it's now stuck on the O2 boot screen and wont budge, wont connect via active sync and does nothing else when I hard reset.
Have I f**ked it up ??
Please help,
Tommy
Don't panic
Just reset the device, place it back in the cradle and re-run the upgrade. It doesn't require Activesync as the upgrade process looks after its own connection.
Make sure the cradle is connected directly into a USB port on your PC and not to a hub. Also make sure the power supply is connected to the cradle.
Thanks, but that doesnt seem to help, the program just says that their is no connection.
Do you have another PC you can use? or try using a different USB port.
tried it on both and nothing, It looks like the XDAII can't start up properly and that's why it can't establish a connection. As I said it's stuck on the O2 boot screen (the one with the bubbles on it) with the version nos at the bottom and does nowt else.
I feel sick...
Tommy
OK. I misunderstood. I thought you were in the bootloader screen. So you need to see if you can put the device into bootloader mode. Press the jog button (bottom middle front of device) and power button at same time whilst pressing the reset button. This (hopefully) will put you in the bootloader - a dark screen with Serial 1.xx displayed. Then when device is put in cradle it should change to USB 1.xx. Then you can re-run the upgrade.
Whayhey
DCS you are indeed the man!
Thanks for your help.
Tommy
hello,
my xda2s is stuck in serial mode please can someone tell me how to get it out of serial mode?
Thank you.
I assumed you tried the soft reset hole and the hard reset (wipe out all data) mode (with power button held down)?
Yeah mine is stuck in the serial mode also. I have tried several different ways to reset it and in won't reset. I don't know if I'm doing it right or not, but I tried to do it by holding down the power and the soft reset button. Then I tried to hold down the camera, record, power, and soft reset buttons and it won't do it.
Please help me also to get it out of the serial mode
Thanks
I don't know if this will help. But I kinda face the similar problem.
My device also stuck in the serial mode while upgrading to the 1.08 Radio ROM.
It was switched to the serial mode by the upgarde software while checking the device ROM. Then it just stuck there forever.
Soft-reset and Hard-reset won't bail me out off the serial mode. And the upgrade software also got stucked on my PC.
What I did was to reboot my PC, replug my XDA IIs back to the craddle (while still in the serial mode) and reflash the ROM again. The second time was a success. The ROM upgrade was smooth and the device was able to get out off the serial mode after a soft reset.
-SJ
Help, my device pda2k is stuck in bootlader mode
All I see is a grey screen with a serial number on top (or USB when the device is placed in the cradle) and on the bottom I see V1.06
I have tried a hard reset but nothing.
reflashed and use the "HimaUpgradeUt_noID.exe"
jojo
I am a bit of a dummy.
Where can I find HimaUpgradeUt.noID.exe???
The link is in xda2jojo's signature.
Cheers!!
hello, first of all i am sorry if this is in the wrong section. you may move topic if you wish. please help.
i was just doing the spv m5000 new upgrade today when my computer just went off in the middle of the setup and now my SPV m5000 displays only to things without the backlight displays (serial and v1.00 when not connected to computer and USB and v1.00 when connected via usb. PLUS NO activeSYNC connection.
I have tryed hard reset but does not work screen comes saying press 0 to hard reset with the back light but nothing happens.
Please help i have just recently got this phone from ebay for over $350.00
Hi folks,
Can anyone help me?
I was using BSB 6.5L WM6.5 on my Diamond and i had some problems with that.
Mainly, my Diamond was "hard reseting" the manufactures settings everytime i turned it on.
So i decided to downgrade it to WM 6.1
At this point i started to have serious issues.
I installed Rom 1.93xx and just after the uptade, my Diamond froze in the first black screen (Touch Diamond and radio/Rom version).
Even if i do the hard reset, it freezes again in the boot screen.?
So, how could i go back to the Rom i was using before or install another one?
My Diamond is useless now... Hope someone can help me.
Thanks
should've used search, this is also a wrong forum for this topic.
with that said, power off the phone, press and hold power, volume down and reset until you see the tri-colour bootloader screen, connect the phone to your PC, you should be able to flash at this point.
do report back.
Japex said:
Hi folks,
Can anyone help me?
I was using BSB 6.5L WM6.5 on my Diamond and i had some problems with that.
Mainly, my Diamond was "hard reseting" the manufactures settings everytime i turned it on.
So i decided to downgrade it to WM 6.1
At this point i started to have serious issues.
I installed Rom 1.93xx and just after the uptade, my Diamond froze in the first black screen (Touch Diamond and radio/Rom version).
Even if i do the hard reset, it freezes again in the boot screen.?
So, how could i go back to the Rom i was using before or install another one?
My Diamond is useless now... Hope someone can help me.
Thanks
Click to expand...
Click to collapse
What technote said is incorrect, doing that will just cause it to try and read from the Internal Storage, what you want to do is what I did when I had the exact same problem;
With the phone on the frozen screen - make sure the USB cable is DISconnected, open ActiveSync/WMDC on the PC and in connection settings, disable USB connections. Now press the red reset button on the phone and as the phone is turning on (before it vibrates - 'touch Diamond' splash), you need to press Volume Down once, don't hold it. Just press it once. Now plug the USB cable in when the tri color screen appears, and Serial should be written near the bottom. Renable USB connections in ActiveSync/WMDC and then flash a ROM. All should work.
Thanks...
It worked flawlessly....
incredulous said:
What technote said is incorrect, doing that will just cause it to try and read from the Internal Storage, what you want to do is what I did when I had the exact same problem;
With the phone on the frozen screen - make sure the USB cable is DISconnected, open ActiveSync/WMDC on the PC and in connection settings, disable USB connections. Now press the red reset button on the phone and as the phone is turning on (before it vibrates - 'touch Diamond' splash), you need to press Volume Down once, don't hold it. Just press it once. Now plug the USB cable in when the tri color screen appears, and Serial should be written near the bottom. Renable USB connections in ActiveSync/WMDC and then flash a ROM. All should work.
Click to expand...
Click to collapse
When i do this, it still keeps going to the splash. I reset, press vol down, and it continues to go to the splash. If i do it the other mentioned way, power, reset, vol down i get to the tri colour screen.
how to enter in bootloader = press volume down and reset simultaneous !
link