MY XDAII is stuck in bootloader mode - Upgrading, Modifying and Unlocking

Help, my device pda2k is stuck in bootlader mode
All I see is a grey screen with a serial number on top (or USB when the device is placed in the cradle) and on the bottom I see V1.06
I have tried a hard reset but nothing.

reflashed and use the "HimaUpgradeUt_noID.exe"
jojo

I am a bit of a dummy.
Where can I find HimaUpgradeUt.noID.exe???

The link is in xda2jojo's signature.
Cheers!!

Related

Stuck on O2 boot screen

While upgrading my XDAII to the new O2 rom, I got a connection error which tiole me to disconnect the xda and do a soft reset.
I did this and it's now stuck on the O2 boot screen and wont budge, wont connect via active sync and does nothing else when I hard reset.
Have I f**ked it up ??
Please help,
Tommy
Don't panic
Just reset the device, place it back in the cradle and re-run the upgrade. It doesn't require Activesync as the upgrade process looks after its own connection.
Make sure the cradle is connected directly into a USB port on your PC and not to a hub. Also make sure the power supply is connected to the cradle.
Thanks, but that doesnt seem to help, the program just says that their is no connection.
Do you have another PC you can use? or try using a different USB port.
tried it on both and nothing, It looks like the XDAII can't start up properly and that's why it can't establish a connection. As I said it's stuck on the O2 boot screen (the one with the bubbles on it) with the version nos at the bottom and does nowt else.
I feel sick...
Tommy
OK. I misunderstood. I thought you were in the bootloader screen. So you need to see if you can put the device into bootloader mode. Press the jog button (bottom middle front of device) and power button at same time whilst pressing the reset button. This (hopefully) will put you in the bootloader - a dark screen with Serial 1.xx displayed. Then when device is put in cradle it should change to USB 1.xx. Then you can re-run the upgrade.
Whayhey
DCS you are indeed the man!
Thanks for your help.
Tommy

xda2s stuck is serial mode

hello,
my xda2s is stuck in serial mode please can someone tell me how to get it out of serial mode?
Thank you.
I assumed you tried the soft reset hole and the hard reset (wipe out all data) mode (with power button held down)?
Yeah mine is stuck in the serial mode also. I have tried several different ways to reset it and in won't reset. I don't know if I'm doing it right or not, but I tried to do it by holding down the power and the soft reset button. Then I tried to hold down the camera, record, power, and soft reset buttons and it won't do it.
Please help me also to get it out of the serial mode
Thanks
I don't know if this will help. But I kinda face the similar problem.
My device also stuck in the serial mode while upgrading to the 1.08 Radio ROM.
It was switched to the serial mode by the upgarde software while checking the device ROM. Then it just stuck there forever.
Soft-reset and Hard-reset won't bail me out off the serial mode. And the upgrade software also got stucked on my PC.
What I did was to reboot my PC, replug my XDA IIs back to the craddle (while still in the serial mode) and reflash the ROM again. The second time was a success. The ROM upgrade was smooth and the device was able to get out off the serial mode after a soft reset.
-SJ

Please Help SPV M5000

Dear All,
I've a problemi with my SPV M5000. After firmware upgrade, my device is stay in USB or Serial mode. I try hot and cold reset but no result? after few seconds it's back to USB or Serial Mode?
So, please help me!
I assume when you say you have hard reset the phone you have held in both soft keys and pressed the reset button? If so, I would flash the phone again, something probably went wrong.
Fin
Re ...
So the set is show only:
Serial on top on the screen and v1.00 on bottom of the screen.
When I connect USB cable is show:
USB on top on the screen and v1.00 on bottom of the screen.
After hot and cold reset this message is back?

(The problem really?) finished

hello
The problem really????
try on I want to UPGRADE to WM6
enter into screen
Written by stuck in grey scren, "Serial" or "USB"
and in the under-screen : V2.07
and No, never go................
( I am stuck in grey scren, "Serial" or "USB" (when the device is placed in the cradle) )
all this in siemens sx66
What is the solution???
I am waiting​
when my pda is in that mode i just run the flash tool and it get a new rom
Was the solution to the problem
Thank you for all

[HELP] Dead Diamond?

Hello,
I posted this thread also in Diamond forum, but there is no response, maybe somebody here can help me?
First my Diamond (in fact it is MDA Compact IV) died during changing battery. I put new battery (original 1340mah from HTC) and he never wake up. I put original battery back, but Diamond is still dead. Here is situation for now:
1. I can't turn the phone ON.
2. If I connect phone to charger or PC phone turns ON. There is one vibra ring and splash screen without numbers in corner (ROM, radio etc). Splash screen in visible for about 10-12 second, then phone is rebooting. It going all around continuously.
3. During displaying splash screen I CAN enter bootloader mode or make hard reset. If I enter to bootloader and plug charger off then phone turns OFF.
In bootloader mode there is such text on display:
DIAM200 MFG 64M
SPL- 1.40. OliNex
MicroP-Diam (LED) v11
pSOC-Vict STAGE_PVT v0x20
USB.
Windows in my PC makes sound as connected USB equipment, but ActiveSync is not connected (gray).
4. After running bootloader mode I CAN run DiamondCustomRUU.exe. It looks like updates, ROM, Radios are installed- indicator is running in my PC and also on Diamond screen. After finishing installation there is again: reset, vibra, splash screen 10-12 second, reset, vibra... etc.
I tried to install many ROM, Radios and all SPL but final is always the same.
5. I tried to install original SPL- installation looks successful, but after reset in bootloader mode there is still: SPL- 1.40. OliNex. This point is most strange for me.
6. I can connect via mtty (but activesync is still gray), but I don't know commands for mtty and I don't know what more can I do through mtty.
For me right now most important is to turn SPL back- then I can return device to service.
Does anybody knows some solutions? I'm opened for any suggestions...
Thanks,

Categories

Resources