(The problem really?) finished - MDA III, XDA III, PDA2k, 9090 General

hello
The problem really????
try on I want to UPGRADE to WM6
enter into screen
Written by stuck in grey scren, "Serial" or "USB"
and in the under-screen : V2.07
and No, never go................
( I am stuck in grey scren, "Serial" or "USB" (when the device is placed in the cradle) )
all this in siemens sx66
What is the solution???
I am waiting​

when my pda is in that mode i just run the flash tool and it get a new rom

Was the solution to the problem
Thank you for all

Related

MY XDAII is stuck in bootloader mode

Help, my device pda2k is stuck in bootlader mode
All I see is a grey screen with a serial number on top (or USB when the device is placed in the cradle) and on the bottom I see V1.06
I have tried a hard reset but nothing.
reflashed and use the "HimaUpgradeUt_noID.exe"
jojo
I am a bit of a dummy.
Where can I find HimaUpgradeUt.noID.exe???
The link is in xda2jojo's signature.
Cheers!!

Please Help SPV M5000

Dear All,
I've a problemi with my SPV M5000. After firmware upgrade, my device is stay in USB or Serial mode. I try hot and cold reset but no result? after few seconds it's back to USB or Serial Mode?
So, please help me!
I assume when you say you have hard reset the phone you have held in both soft keys and pressed the reset button? If so, I would flash the phone again, something probably went wrong.
Fin
Re ...
So the set is show only:
Serial on top on the screen and v1.00 on bottom of the screen.
When I connect USB cable is show:
USB on top on the screen and v1.00 on bottom of the screen.
After hot and cold reset this message is back?

XDA EXEC stuck at spalsh screen after flashing

Hai ,
I tried different flashes of WM6 , then i reverted back to wm5.
But then again i flashed it with wm6 rom.
It flashes it successfully but after hard reset , pressing 0 , it just stays at splash screen giving infos in red.
I am stuck at spalsh screen ... any ideas ?
Also tried uni_exitbootloader .. but still stucks at splash screen
Tried Refalshing it many times but same ..
babablacksheep said:
Hai ,
I tried different flashes of WM6 , then i reverted back to wm5.
But then again i flashed it with wm6 rom.
It flashes it successfully but after hard reset , pressing 0 , it just stays at splash screen giving infos in red.
I am stuck at spalsh screen ... any ideas ?
Also tried uni_exitbootloader .. but still stucks at splash screen
Tried Refalshing it many times but same ..
Click to expand...
Click to collapse
Try enter bootloader and re-flash WM6 Rom, if it still fails to boot, search the Universal forum for MTTY commands to reset partition tables. I suspect the partitions are corrupt.
Hope youre battery is not too low.
Cheers,
Beast
babablacksheep said:
Hai ,
I tried different flashes of WM6 , then i reverted back to wm5.
But then again i flashed it with wm6 rom.
It flashes it successfully but after hard reset , pressing 0 , it just stays at splash screen giving infos in red.
I am stuck at spalsh screen ... any ideas ?
Also tried uni_exitbootloader .. but still stucks at splash screen
Tried Refalshing it many times but same ..
Click to expand...
Click to collapse
Something like this happened to me when I first flashed my Universal, I tried something in the Wiki (Cannot remember?) That told me to use that usb port from now on for all flashing. After that it worked. I will search further to see if I can help...
Okie Problem Solved.
I did this to get myself sigh if relief.
100% working
1. Take out the SD and SIM cards
2. Opened ActiveSync and go to file, connection setting and Un-check "Allow USB Connections". Then press Ok and close ActiveSync
3. Put in bootloader mode (Power + Light + reset) which brings up the "un-backlit" screen with "Serial" at the top and v0.XX at the bottom
4. Plug in USB cable DIRECTLY from PC to Jasjar (MAKE SURE NOT TO USE A USB HUB). You MIGHT then see a warning window complaining that an "Unsigned" device driver is being attempted to be installed. You will be prompted to either "STOP INSTALLATION" or "CONTINUE ANYWAY" - this warning can be safely ignored and so just click on "CONTINUE ANYWAY".
5. Open mtty utility / software
6. Select USB from the "Port" drop-down on the upper left corner of the dialog box and hit OK
7. Then another screen will come up. Hit enter and that will show "USB>"
8. Type "task 28 55aa" and hit enter. {type it manually/ don`t copy and paste commands}
9. use the "Original OEM ROM" that is made for your device and update with it (CE,Extended and Radio) Flash all
10. Hard Reset
Also if your device bootloader version is lower than "v 1.01" you should update that first (before installing the OEM ROM, but NOT before "Task 28 55aa").
After this is complete you may then use your device again.
NOTe : I find you must kill the wcescomm, wcesmgr and rapimgr exe's using task manager before you get the 'usb' option in mtty (kills activesync)
Please,
what to do when there's no USB port in mtty (only COM1 and COM2) ?????
babablacksheep
must say -Thank you!
vjj said:
Please,
what to do when there's no USB port in mtty (only COM1 and COM2) ?????
Click to expand...
Click to collapse
You must disable ActiveSync before connection
and put in bootloader mode (Power + Light + reset) BEFORE run MTTY
after USB must appear in drop-down menu
one more time thanked babablacksheep

[HELP] Dead Diamond?

Hello,
I posted this thread also in Diamond forum, but there is no response, maybe somebody here can help me?
First my Diamond (in fact it is MDA Compact IV) died during changing battery. I put new battery (original 1340mah from HTC) and he never wake up. I put original battery back, but Diamond is still dead. Here is situation for now:
1. I can't turn the phone ON.
2. If I connect phone to charger or PC phone turns ON. There is one vibra ring and splash screen without numbers in corner (ROM, radio etc). Splash screen in visible for about 10-12 second, then phone is rebooting. It going all around continuously.
3. During displaying splash screen I CAN enter bootloader mode or make hard reset. If I enter to bootloader and plug charger off then phone turns OFF.
In bootloader mode there is such text on display:
DIAM200 MFG 64M
SPL- 1.40. OliNex
MicroP-Diam (LED) v11
pSOC-Vict STAGE_PVT v0x20
USB.
Windows in my PC makes sound as connected USB equipment, but ActiveSync is not connected (gray).
4. After running bootloader mode I CAN run DiamondCustomRUU.exe. It looks like updates, ROM, Radios are installed- indicator is running in my PC and also on Diamond screen. After finishing installation there is again: reset, vibra, splash screen 10-12 second, reset, vibra... etc.
I tried to install many ROM, Radios and all SPL but final is always the same.
5. I tried to install original SPL- installation looks successful, but after reset in bootloader mode there is still: SPL- 1.40. OliNex. This point is most strange for me.
6. I can connect via mtty (but activesync is still gray), but I don't know commands for mtty and I don't know what more can I do through mtty.
For me right now most important is to turn SPL back- then I can return device to service.
Does anybody knows some solutions? I'm opened for any suggestions...
Thanks,

Need help..My BA stuck in 'USB' / 'Serial' gray screen

heloo
I am currently upgrading my XDAIIs from WM2003 to WM6.5.
after checking the system from my XDAIIs, suddenly the power led went off and the sync is disconnected so I cannot continue the upgrade. On my phone screen there are only gray screen with USB at the top and V.2.07 at the bottom.
I have tried to restart the upgrading process but the problem is now my phone cannot connected to my laptop although I am using USB. I also tried to change the usb port and sync with other computer, but the problem is still the same.
FYI : at the beginning of the upgrade process, I didn't hard reset the phone. Is this the cause of the problem??
Please help me, does anyone have any solutions?
your device is in bootloader mode and it should show up as a ms_wm_device in
windows and you should be able to flash it again you can read more here
http://wiki.xda-developers.com/index.php?pagename=HTC_Blueangel
chanxda... you sorted it yet! I had same problem last nite and figured it out. Ill watch thread if you need reply!

Categories

Resources