[Q] I-MATE JASJAR hung - JASJAR, XDA Exec, MDA Pro Software Upgrading

Hi every one,
i have a serious problem with my HTC I-MATE JASJAR what's blocked in white screen (Serial / USB) and i cannot do anything on it, no boot, no reset soft, no reset Hard, no upgrade.
The issue is related to:
I tried to upgrade Radio ROM from 1.09.00 to 1.12 and i'm using Windows 7 Pro and when starting Flash, my PC shutdown because an electrical issue and since that, i cannot boot my device, i cannot flash or reset, my device is hung on white screen with Serial when no USB cable bluged in the PC and USB when Cable is pluged.
I Tried many times to boot it but no response, it's still hung and nothing can move on it.
I Just have one detail: when i plug the USB cable in my PC, the device is reconised but when starting upgrade or flash, i have error 101, no connexion.
Plz someone help me :crying::crying::crying::crying::crying::crying:

Related

Stuck on O2 boot screen

While upgrading my XDAII to the new O2 rom, I got a connection error which tiole me to disconnect the xda and do a soft reset.
I did this and it's now stuck on the O2 boot screen and wont budge, wont connect via active sync and does nothing else when I hard reset.
Have I f**ked it up ??
Please help,
Tommy
Don't panic
Just reset the device, place it back in the cradle and re-run the upgrade. It doesn't require Activesync as the upgrade process looks after its own connection.
Make sure the cradle is connected directly into a USB port on your PC and not to a hub. Also make sure the power supply is connected to the cradle.
Thanks, but that doesnt seem to help, the program just says that their is no connection.
Do you have another PC you can use? or try using a different USB port.
tried it on both and nothing, It looks like the XDAII can't start up properly and that's why it can't establish a connection. As I said it's stuck on the O2 boot screen (the one with the bubbles on it) with the version nos at the bottom and does nowt else.
I feel sick...
Tommy
OK. I misunderstood. I thought you were in the bootloader screen. So you need to see if you can put the device into bootloader mode. Press the jog button (bottom middle front of device) and power button at same time whilst pressing the reset button. This (hopefully) will put you in the bootloader - a dark screen with Serial 1.xx displayed. Then when device is put in cradle it should change to USB 1.xx. Then you can re-run the upgrade.
Whayhey
DCS you are indeed the man!
Thanks for your help.
Tommy

Hello Guys I need Your Help

First of all Hello
I've been trying to update my XDA2i Pocke PC for more than an hour
and every time I start the Update Operation I got an error message and the operation corrupt agian it prompts me to reset it, after the reset, it informs me to disconnect the Pocket and Cardle USB, and reconnect it Again but it gave me a message on its screen told me Serial on the top of the screen, and on the buttom V1.01< What should I do?
Please Help me to get it alive again because it's dead now, and it won't work anymore, I need the method of booting it up, what are the buttons combinations to enter the boot again.
and If you gave the ROM Update for it, I'd be so grateful!! :lol:
PS: the Pocket information are
Pocket PC O2 XDA2i
Are you using a usb hub to connect, if you are then try plugging in direct to usb port. You will not be able to boot until you complete the flashing procedure, the program has probably wiped your previous rom.
It didn't work
Thanks sir,
but how can I do the flashing procedure, the Pocket PC wouldn't give the chance to do it!
and I've already plugged the USB directly to the PC.
Could you give the manner to falsh it again and boot,
because it is dead and silent
I'll be so grateful for your efforts

Emergency: Stuck In Bootloader mode

Helmi's AKU 3.5 ROM was installing at that time and it was interupted by a 101 connection error. I disconnected the Universal from the USB and I was seeing the bootloader screen where it only shows Serial and 1.00. I tried to press the reset button. It still went back to the bootloader screen where it shows serial and 1.00. Next i tried to hard reset the device by pressing - & - & reset. I was given two options of 0 & X. First time i tried X and it still went back to Serial and 1.00 bootloader screen. Then i tried to hard reset again and this time i selected 0, it cleared the device and it went back to the bootloader screen. . Then i tried installing Helmi's ROM again. Well it wouldn't work because the USB mentioned it as an unknown device. I tried mtty but mtty wouldn't list a USB port in the dropdown list. All i saw was COM ports. Next i tried it on another computer and it still would not work. Tried to update the bootloader but same 101 device not detected problem.
reflash your bootloader
Oh nvm this thread post. I got it fixed. It was my USB cable that was faulty. All the pins in the USB cable were not hitting all the pins USB port. I used another USB cable and it works now. I guess this post helps all zombies like me.

bootloadr hange up

i flashed my touch diamond with a cooked rom every thing went well untill 1st reboot after completing the flash then black screen with diamond touch logo and nothing i have tried soft reset many times usb cable is not detectable then i tried the program ECShift.exe
when i write ECShift.exe -bl in cmd it says "could not open EC!" so i can not use mtty please help what i can do with the device is it now broken for final or it can be repaired since i can not log in to bootloader
also when i switch it off and put the usb cable it indicates that it is recharging but when i try to turn it on it doesn't start and if i unplugged the usb cable now it still gives me the indication for recharging (whispering light)
usb is not recognized even when making hard reset without formatting the internal storage i get the colored screen the the 3 choices so fast even the diamond does not detect it is connected to pc it suppose to give me a screen writing usb
hi i have the same problem with diamond! you can fixed?tanks

Need help..My BA stuck in 'USB' / 'Serial' gray screen

heloo
I am currently upgrading my XDAIIs from WM2003 to WM6.5.
after checking the system from my XDAIIs, suddenly the power led went off and the sync is disconnected so I cannot continue the upgrade. On my phone screen there are only gray screen with USB at the top and V.2.07 at the bottom.
I have tried to restart the upgrading process but the problem is now my phone cannot connected to my laptop although I am using USB. I also tried to change the usb port and sync with other computer, but the problem is still the same.
FYI : at the beginning of the upgrade process, I didn't hard reset the phone. Is this the cause of the problem??
Please help me, does anyone have any solutions?
your device is in bootloader mode and it should show up as a ms_wm_device in
windows and you should be able to flash it again you can read more here
http://wiki.xda-developers.com/index.php?pagename=HTC_Blueangel
chanxda... you sorted it yet! I had same problem last nite and figured it out. Ill watch thread if you need reply!

Categories

Resources