bootloadr hange up - Touch Diamond, MDA Compact IV ROM Development

i flashed my touch diamond with a cooked rom every thing went well untill 1st reboot after completing the flash then black screen with diamond touch logo and nothing i have tried soft reset many times usb cable is not detectable then i tried the program ECShift.exe
when i write ECShift.exe -bl in cmd it says "could not open EC!" so i can not use mtty please help what i can do with the device is it now broken for final or it can be repaired since i can not log in to bootloader
also when i switch it off and put the usb cable it indicates that it is recharging but when i try to turn it on it doesn't start and if i unplugged the usb cable now it still gives me the indication for recharging (whispering light)
usb is not recognized even when making hard reset without formatting the internal storage i get the colored screen the the 3 choices so fast even the diamond does not detect it is connected to pc it suppose to give me a screen writing usb

hi i have the same problem with diamond! you can fixed?tanks

Related

PLEASE HELP!!!!

I tried using the Siemens upgrade for my SX66, which made it display Serial on the top and v2.07 on the bottom
I followed the steps reccomended for when such a thing takes place (ie doing a flash reset on the phone) but now the screen remains black and doesn't even display Serial and v2.07
When plugged into my computer, absolutely nothing happens and the computer does not recognize it.
I eventually got the screen to display USB, ran the update again but after about 15 minutes I got an error screen on the PC that read:
Error 201: Get Device Data Error
Can not get device data. Please make sure device are connected to PC and execute this update utility again
Please help!
Someone help this poor person.....

HELP!! Diamond Stuck in bootlaoder

Help pls i have olinex 1.40 hardspl in but my phone is stuck in bootloader with "upgrade ROM code error Please try again" i cant get out...tried hard reset nothing...tried recovery mode (volume down + reset ) nothing...cant get a usb connection help!!!!!!!!!!!!!!!!
are you sure you don't have usb connection? try running an ruu with usb plugged in see if it runs. it sounds like you tried to flash a radio from another device. try flashing a new radio.
Blazeitup123 said:
are you sure you don't have usb connection? try running an ruu with usb plugged in see if it runs. it sounds like you tried to flash a radio from another device. try flashing a new radio.
Click to expand...
Click to collapse
the bootloader shows usb when i plug it in and serial when i plug it out...when hard resetting it goes through the formatting but then just jumps back to bootloader with the message...active sync recognizes nothing but i'll try that right now
edit - ok it seems to be flashing i'm crossing my fingers
edit: ok it seems to have flashed i see my rogers main screen thank you soooooooooooooooo much
glad to hear!
just so you know you can always flash from bootloader. i have seen alot of people around here saying "oh no, my device is bricked and i'm stuck in bootloader". i lol.
Blazeitup123 said:
glad to hear!
just so you know you can always flash from bootloader. i have seen alot of people around here saying "oh no, my device is bricked and i'm stuck in bootloader". i lol.
Click to expand...
Click to collapse
lmao now i know..i was coming from an elfin, not used to diamond as of yet but now i know
Bootloader bottom says "serial" but wont switch to "usb"
Perhaps this is a known issue but I could not find the solution easily and ended up discovering it myself so wanted to share it in case others face the same.
I was try to use the mtty software to "clean" my touch diamond in an effort to get rid of some bugs in macadam 1.2 rom [great rom, by the way].
I had disabled the usb connections in active sync on my laptop [mac running windows xp in bootcamp]
I could enter bootloader easily but the bottom part of the multicolor screen kept saying "serial" and would not switch to "usb" when I connected the phone to the laptop.
What finally worked was ensuring that the phone was set for "activesync" rather than use as a "disk drive" or "internet sharing". I had assumed, wrongly, that once in bootloader the last selected option [disk drive] would be irrelevant.
So I exited the bootloader by pressing the reset key; connected phone to pc via cable; selected the active sync option; disconnected the phone; entered bootloader, connected the phone via cable again and the bottom of the bootloader changed to usb and I was able to use mtty successfully.
I wonder if this has implications for people stuck with bad flashes etc. In my case I could easily exit the bootloader and go back and select 'activesync' from the working phone. One could also hard reset if a working rom was on the phone...
BUT If one is stuck with the option of only the bootloader, would it matter on what the last selected option was [active sync or use as usb disk drive or internet sharing]?
faisal said:
Perhaps this is a known issue but I could not find the solution easily and ended up discovering it myself so wanted to share it in case others face the same.
I was try to use the mtty software to "clean" my touch diamond in an effort to get rid of some bugs in macadam 1.2 rom [great rom, by the way].
I had disabled the usb connections in active sync on my laptop [mac running windows xp in bootcamp]
I could enter bootloader easily but the bottom part of the multicolor screen kept saying "serial" and would not switch to "usb" when I connected the phone to the laptop.
What finally worked was ensuring that the phone was set for "activesync" rather than use as a "disk drive" or "internet sharing". I had assumed, wrongly, that once in bootloader the last selected option [disk drive] would be irrelevant.
So I exited the bootloader by pressing the reset key; connected phone to pc via cable; selected the active sync option; disconnected the phone; entered bootloader, connected the phone via cable again and the bottom of the bootloader changed to usb and I was able to use mtty successfully.
I wonder if this has implications for people stuck with bad flashes etc. In my case I could easily exit the bootloader and go back and select 'activesync' from the working phone. One could also hard reset if a working rom was on the phone...
BUT If one is stuck with the option of only the bootloader, would it matter on what the last selected option was [active sync or use as usb disk drive or internet sharing]?
Click to expand...
Click to collapse
This doesn't make any difference. When you're stuck in bootloader just plugin your USB and the display will state "USB" as well. You can flash a rom at this point.

Tricolored Screen Madness!

i have the red, green and blue screen going on and no matter what i try to do its not doing anything, i tried to reinstall the OS and my pc wont detect any phone that is connected. is there anyway i can get this phone back to normal?
damn.. anyone please?
Hey crazy first thing i would try is to make sure you have active sync installed and the connection manager set to connect via usb. if you have it setup right active sync should recognize the phone whether the comp does or not as long as active sync sees the folders you can flash. secoundly use the search option for the forum to find related articles for the loader screen and flashing.
tri-color screen, that is Boot loader mode, where you can flash/ reflash your EXCA to a new rom. Make sure you install "Activesync", make sure you plug the USB cable to your EXCA.
When you plug the usb cable, the tri-color screen will change the "Serial" to "USB".
That mean, your computer has recognized your phone.
The rest of thing, you could spend little time to know: "HOW TO FLASH A NEW ROM SUCCESSFULLY?"
Good luck.

[Q] I-MATE JASJAR hung

Hi every one,
i have a serious problem with my HTC I-MATE JASJAR what's blocked in white screen (Serial / USB) and i cannot do anything on it, no boot, no reset soft, no reset Hard, no upgrade.
The issue is related to:
I tried to upgrade Radio ROM from 1.09.00 to 1.12 and i'm using Windows 7 Pro and when starting Flash, my PC shutdown because an electrical issue and since that, i cannot boot my device, i cannot flash or reset, my device is hung on white screen with Serial when no USB cable bluged in the PC and USB when Cable is pluged.
I Tried many times to boot it but no response, it's still hung and nothing can move on it.
I Just have one detail: when i plug the USB cable in my PC, the device is reconised but when starting upgrade or flash, i have error 101, no connexion.
Plz someone help me :crying::crying::crying::crying::crying::crying:

htc desire mode auto after water and problem

the other day it went a little water to my htc desire froyo rom and I rode half an hour after I have left in acccensione fastboot screen ... blocked for 10 minutes and then restarts rom ... after a couple of hours the back button works more, and still reboot fastboot screen. I remove the battery and restart several times but after a while '... same problem ... with even more original rom does not read usb cable from pc and phone, when attacks cable does not detect it ... putting a rom cooked midway detects cable and usb mass storage .... but with original ROM by power-on auto mode active and if you call the part with the hands-free cell with the rom cooked .. no problem .. but I did not understand that it happened 'cause I can not replace more rom original file and I washed again with the usb and instead cooked crashes after a while?'ve flashed with various rome but nothing .. what can I change?

Categories

Resources