PLEASE HELP!!!! - MDA III, XDA III, PDA2k, 9090 General

I tried using the Siemens upgrade for my SX66, which made it display Serial on the top and v2.07 on the bottom
I followed the steps reccomended for when such a thing takes place (ie doing a flash reset on the phone) but now the screen remains black and doesn't even display Serial and v2.07
When plugged into my computer, absolutely nothing happens and the computer does not recognize it.
I eventually got the screen to display USB, ran the update again but after about 15 minutes I got an error screen on the PC that read:
Error 201: Get Device Data Error
Can not get device data. Please make sure device are connected to PC and execute this update utility again
Please help!

Someone help this poor person.....

Related

Hello Guys I need Your Help

First of all Hello
I've been trying to update my XDA2i Pocke PC for more than an hour
and every time I start the Update Operation I got an error message and the operation corrupt agian it prompts me to reset it, after the reset, it informs me to disconnect the Pocket and Cardle USB, and reconnect it Again but it gave me a message on its screen told me Serial on the top of the screen, and on the buttom V1.01< What should I do?
Please Help me to get it alive again because it's dead now, and it won't work anymore, I need the method of booting it up, what are the buttons combinations to enter the boot again.
and If you gave the ROM Update for it, I'd be so grateful!! :lol:
PS: the Pocket information are
Pocket PC O2 XDA2i
Are you using a usb hub to connect, if you are then try plugging in direct to usb port. You will not be able to boot until you complete the flashing procedure, the program has probably wiped your previous rom.
It didn't work
Thanks sir,
but how can I do the flashing procedure, the Pocket PC wouldn't give the chance to do it!
and I've already plugged the USB directly to the PC.
Could you give the manner to falsh it again and boot,
because it is dead and silent
I'll be so grateful for your efforts

Hopeless HTC s621

I have my device unlocked already and have done many ROM upgrades before, this time my PC froze half way throught the upgrade. The device turns on and gets stuck on the T-mobile screen. It doesnt connect to active sync i cant even get Dashv2unlock to detect my device. Please help somebody.
from what i've read before about this type of issue (somewhat), try removing the battery and SIM for a few minutes, then replace and reboot and see if active sync recognizes it now.
if this info is no longer valid, I apologize.
I think you need to have your phone in bootloader mode and then flash again. Make sure the phone is off, and while holding down the camera key (to the right of the space key), connect the USB cable to your phone. The tri color bootloader screen should appear on your S620. Now run the upgrade file on your PC again.
Let us know how it goes....
im able to get to the tri color screen but when i start any Rom upgrade it gets to 3 percent and fails. I have also tried the SP-1.11 upgradeonly.exe and also the Dashv2Unlocker that i have paid for. Nothing

bootloadr hange up

i flashed my touch diamond with a cooked rom every thing went well untill 1st reboot after completing the flash then black screen with diamond touch logo and nothing i have tried soft reset many times usb cable is not detectable then i tried the program ECShift.exe
when i write ECShift.exe -bl in cmd it says "could not open EC!" so i can not use mtty please help what i can do with the device is it now broken for final or it can be repaired since i can not log in to bootloader
also when i switch it off and put the usb cable it indicates that it is recharging but when i try to turn it on it doesn't start and if i unplugged the usb cable now it still gives me the indication for recharging (whispering light)
usb is not recognized even when making hard reset without formatting the internal storage i get the colored screen the the 3 choices so fast even the diamond does not detect it is connected to pc it suppose to give me a screen writing usb
hi i have the same problem with diamond! you can fixed?tanks

Need help..My BA stuck in 'USB' / 'Serial' gray screen

heloo
I am currently upgrading my XDAIIs from WM2003 to WM6.5.
after checking the system from my XDAIIs, suddenly the power led went off and the sync is disconnected so I cannot continue the upgrade. On my phone screen there are only gray screen with USB at the top and V.2.07 at the bottom.
I have tried to restart the upgrading process but the problem is now my phone cannot connected to my laptop although I am using USB. I also tried to change the usb port and sync with other computer, but the problem is still the same.
FYI : at the beginning of the upgrade process, I didn't hard reset the phone. Is this the cause of the problem??
Please help me, does anyone have any solutions?
your device is in bootloader mode and it should show up as a ms_wm_device in
windows and you should be able to flash it again you can read more here
http://wiki.xda-developers.com/index.php?pagename=HTC_Blueangel
chanxda... you sorted it yet! I had same problem last nite and figured it out. Ill watch thread if you need reply!

Zenfone 2 does not turn on

Good morning, I have a big problem in my Zenfone 2 and would very much like your help.
Yesterday in the morning he hung up, I thought I had downloaded but I tried to turn it when he called saw the battery was at 50%, I found strange but ok, then the screen locked and the phone started to vibrate and I had to off it. When I called, the battery was at 50%, was saying that the phone was connected and there do not leave sound and saying he was carrying. I thought it might be the rom and turned it on PC to back up and exchange of rom, only the USB no longer recognized the connection to the PC. Was saying that tava carrying, I took the USB and stopped "load" when I called he carried again, just not giving connection to the PC. Anyway I did not back up and changed the rom, he continued the same thing (I was in the AICP (LP) and put the RussiaNBear (LP)).
So I was following a tutorial that I had used before to repair another error (I could not post the tutorial link here, but it's on youtube: (Tutorial - Zenfone 2 unbrick / Restore (ZE551ML / ZE550ML) - In the Droid Will channel)), but I gave soft to do so because the part of the AFT (Asus Flash Tools) it does not recognize the phone, having to disconnect the usb and connect again, and then I screwed me, 'cause the uSB connection was not working. After a few unsuccessful attempts, it seems I agravei even more the situation because now I turn the USB cable pressing volume down and it goes in "Moorefield" and the PC identifies a good, open the xFSTK and can pass the DNX, but when you finish spending DNX the phone should reboot and a screen appears with the symbol of a uSB connection, but that's not what happens. I spend the DNX, the phone restarts and vibrates, there is the xFSTK waiting to pass the OS, but not USB screen appears, the xFSTK does not recognize the phone more in "Moorefield" and I can not do anything else on the device.
I have already connected the phone on another pc, I have changed the cable and nothing. I think it is the mobile usb, if not it would not recognize the first part of xFSTK.
Apologies if I have not posted in the right place, for my English (Google Translate) and the text size, only tried to leave everything well explained so that everyone can understand. Thank you very much, beforehand to help you and I really hope we can solve this problem.
Thank you.
No one ?
no one can help me?

Categories

Resources