Hi.
Think I have a real problem. My xda2 is in bootloader mode ready to be re-rommed, but my activesync (3.7) will not register that xda2 is connected. Tried loads of times re-installing activesync (different versions) with no joy at all. xda2 just sat there with dark screen waiting for rom. Please help.
Related
hello, first of all i am sorry if this is in the wrong section. you may move topic if you wish. please help.
i was just doing the spv m5000 new upgrade today when my computer just went off in the middle of the setup and now my SPV m5000 displays only to things without the backlight displays (serial and v1.00 when not connected to computer and USB and v1.00 when connected via usb. PLUS NO activeSYNC connection.
I have tryed hard reset but does not work screen comes saying press 0 to hard reset with the back light but nothing happens.
Please help i have just recently got this phone from ebay for over $350.00
during a ROM flash (rom build with romkitchen), the flash procedure hangs with the "5 minutes..." notification. After a softreset i still get the "5 minutes" screen.
After this disaster, I'am not able to boot in to the bootloader screen anymore. Before this hangup, there was no problem to boot to the bootloader screen.
I reboot my XDA (wallaby) with "press the powerbutton en the resetswitch". The xda reboots, does not show the bootloader screen, but shows right away the "5 minute..." screen.
I have already tried the tool "pnewbootloader" without any result.
Activesync does regonize my anymore, says: not connected.
Is there a way the restore/rebuild/re-flash the bootloader on my XDA (qtek 1010) wallaby?
Thanks in advange.
Greetings
Patrick
Today i have tried to connect to my XDA (wallaby) with "mtty".
when i place my xda in the cradle, mtty is able to connect, but there is no "USB>" prompt.
When i take the xda out the cradle, mtty is unable to essablish an USB-connection. So i am sure that mtty is able to connect to the XDA, but only with out a promt. Due to that i am not able to send commands to the xda.
I also found the JTAG solution, but i'am not an electric expert (i am no good in solder). So the JTAG is no option for me.
I anyone has a solution i would be very thankfull.
greetings,
Patrick
Dear All,
I'm stuck with this XDA Stealth, and guess I need help from you people.
How can I enter Bootloader Mode on XDA Stealth? ( I can enter engineering mode, but can't see any option to enter Bootloader i.e. tri-color screen).
I'm unable to upgrade ROM on this device because of the following reasons.
1. I upgraded WM6.1, and found that Active Sync won't work unless patched.
2. The display's touch screen is defective so after up ROM Upgrade, I'm stuck at align screen, further, the phone is not getting detected in windows as there is this patch required for the ROM.
3. I don't have miniSD reader and also I don't think the car works properly.
So, is there any way to enter the bootloader mode and get the device detected under windows so that I can upgrade again?
wbr
Sonny
For active synch problem, try this
go to setting..connections...usb to pc and uncheck this one
and connect again ....hope this will help
I'm stuck on Align Screen due to bad display. I cannot connect to Active Sync due to bad/cooked ROM.
This is Catch 22
Is there any way to unbrick this phone.
Yesterday, I tried to upgrade my T-mobile Dash ROM to WM6.1 ROM by kavana. I downloaded and ran both the SDA application unlock and the Excalibur USPL - Cid Bypass. After I completed all the steps, I run the upgrade ROM but it failed at 4% with error 270. After that, I turned the phone off and turned it back on; however, it now stuck on the red(ONBL1.10.0000), green(SPL1.10.0000), and blue(IU) screen every time I turned the phone on.
After I searched using the search function in this forum, I found several solutions, but none of them work for me. I tried to do hard reset (pressing soft buttons) with no success. I also tried to flash the original T-mobile WM5 ROM with no success(error 260) even though the phone is already connected to the PC. My computer cannot read the phone, but the USB indicator on the bottom right corner can detect there is a mobile device connected to the pc.
Is there anyway that I can do to repair my phone?
Same problem here.
On normal boot I get the HTC logo and nothing else.
Hard reset doesn't work.
I can enter the bootloader (Camera+power) but have attempted to flash several roms all failing.
Any suggestions please?
Thanks to all
heloo
I am currently upgrading my XDAIIs from WM2003 to WM6.5.
after checking the system from my XDAIIs, suddenly the power led went off and the sync is disconnected so I cannot continue the upgrade. On my phone screen there are only gray screen with USB at the top and V.2.07 at the bottom.
I have tried to restart the upgrading process but the problem is now my phone cannot connected to my laptop although I am using USB. I also tried to change the usb port and sync with other computer, but the problem is still the same.
FYI : at the beginning of the upgrade process, I didn't hard reset the phone. Is this the cause of the problem??
Please help me, does anyone have any solutions?
your device is in bootloader mode and it should show up as a ms_wm_device in
windows and you should be able to flash it again you can read more here
http://wiki.xda-developers.com/index.php?pagename=HTC_Blueangel
chanxda... you sorted it yet! I had same problem last nite and figured it out. Ill watch thread if you need reply!