Related
Dear Fellow Forum Members,
Followed instructions as per Xda_II_Upgrade.pdf, during installation got to a section where I got a message saying that the current rom is being erased a task bar was displayed which increase's in percentage as the job goes through. However the job was still at 0% completion when an error message was displayed saying the job had failed and the device needed to be undocked and a soft reset performed and then re-docked and to restart the process again. After performing the undocking of the device and software reset I get a message on the screen serial V1.0.1 when connected to the cradle the message changes to USB 1.01 and I cannot do anything else the unit does not boot into pocketpc, as you can imagine this is very frustrating as I depend on my xda2 to receive and make phone calls I would be very grateful any members know of any way to get around this problem. I must say I am a bit concerned a try and tested xda2 update has led to this problem.
Just run the update .exe file again with the XDA docked and it should just install the update again. It happened to my mate on Saturday with his XDA II and he just ran the program again.
Dave,
done as you said and all went thru fine you are a star thanks mate.
No problems it's good as a newbie to be able to actually help people.
upgrade xda2 rom ver 172187 dead os--connection error
i was trying to upgrde the rom from o2 website when error occured at stage 19% completed asking me to reset the xda2 . when i am trying to reset the xda 2 it does not boot it just shows the o2 screen with red letters of the version and does not even charge. my laptop cannot connect to xda2 and as a result i am unable to upgrade when i tried to run the 172187 .exe again it gives error 101: connection error
please help me out of this? thanks
i recently tried to update my universal, with the crossbow rom, after pluging the device in my desktop, it started with the update, and placing a message, connection erorr , resulting in ,that my device is stuck in the boot mode, and will not react anymore.
i have tried to update ,without result , i keep getting the message 150 connection error
id there anybody out therer who has had the same problem, if so did you fix , and how did you fix it?
regards peter
I will tell you what I did it my be wrong but I unpluged the usb from the uni and pushed the front light button,power button and the reset at the same time and pluged it in again you get the popup found new device ppc. Then reran the rom update.
NO, just take the SD Card out of the slot and proceed with the update. You must be using a 4GB SD Card, aren't you?
rom upgrade ,universal dead
i keep getting the following message, even if i take the 4gb sd card out of device:
error 150 rom upgrade utility error.
please help it is driving me crazy.
regards peter
pcsw said:
i keep getting the following message, even if i take the 4gb sd card out of device:
error 150 rom upgrade utility error.
please help it is driving me crazy.
regards peter
Click to expand...
Click to collapse
Hi, are you able to get in to the bootloader mode?
Try reading:
http://wiki.xda-developers.com/inde...tion On How To Upgrade with Bootloader method
http://wiki.xda-developers.com/index.php?pagename=Instructions for those stuck on Boot Screen
http://wiki.xda-developers.com/inde...ose stuck on Boot Screen (UNI_exitbootloader)
Hope it helps.
Hi friends,
I got HTC S620 Smartphone from my brother US. It was working well for the past 6 months and i updated to WM6 also now suddenly it got corrupted and shows the following error. It takes 30 min to boot and hangs with this following error. i Unable to do anything. I tried to update WM6 again but same still same error. I gave it to HTC service center in chennai and he unable to resolve this problem. And I Unable to open folder with usb cable. Any one please help me.
t-zones
While retriving the URL :
http://wap.t.zones.com
the following error occured:
Network error 19:
The Attempt to connect to the server failed
More Information Try Again
Alert
Cannot Start 'winwapexe'. A critical component
is either missing or failed due to low memory.
Try to upgrade to the HTC rom, it should be in this forum and I think its the second one on this page... Just look up and you should see the guide to upgrading your rom...
Read the topic that says guide to upgrading from WM 5 to WM 6 (or something along those lines)...
Hi I already Installed WM6 and after this problem again i done WM6 update. I have a doubt with this update. And i Unable to Open Windows Mobile folders from my computer also Active Sync unable to connect with Mobile. But i can receive the call and make answer to them sometime( even Hanging condition).
Hi all dear masters,
I was trying to upgrade my Imate PDA2k, it was failed and now it's not booting.. In the screen, just a "SERIAL" appearing and changes to "USB" when connected to the PC... I tried to upgrade again but now, it says "COUNTRY ID ERROR N-N-12-12-12" and aborting...
Is there anything that I can do?
Any help would be appreciated..
Thanks...
Sorry, I found WM6 upgrade and mtty1.2 and process brought my PDA back... Thank you..
I have the same problem
My mda compact 2 starting playing up yesterday, rebooting on its own, so I tried to install the upgrade from tmobile (ruu charmer). The upgrader stopped and my mda now has a screen that only either says serial v1.02 or usb v1.02.
I've tried rebooting it several times in several different ways without any joy, the screen just remains the same. I tried connecting to my laptop via active sync, but its like it doesn't exist anymore!
In simple terms, could someone please explain how to fix our problem.
[Program \Lokiwiz.bat blows up at the operation:
Copying C:\Lokiwiz03\Utils\itsutils.dll to WCE:\windows\itsutils.dll
and returns the error message:
"Could not update itsutils.dll to the current version, maybe it is inuse? try restarting your device, or restart activesync or maybe your device is application-locked."
I have restarted device and activesync but no luck. As for the device being "application-locked", I don't think so but don't know how to confirm that.
SOMEBODY, PLEASE HELP!!![/SIZE][/FONT]
Fuhgeddaboudid
Problem solved! Used totally different approach with WST. Now up and running in WM 6 but fighting resistance from Synch. Will struggle a while longer before sending Mayday calls.