XDA2 172181_final.exe update problems Help Required - Upgrading, Modifying and Unlocking

Dear Fellow Forum Members,
Followed instructions as per Xda_II_Upgrade.pdf, during installation got to a section where I got a message saying that the current rom is being erased a task bar was displayed which increase's in percentage as the job goes through. However the job was still at 0% completion when an error message was displayed saying the job had failed and the device needed to be undocked and a soft reset performed and then re-docked and to restart the process again. After performing the undocking of the device and software reset I get a message on the screen serial V1.0.1 when connected to the cradle the message changes to USB 1.01 and I cannot do anything else the unit does not boot into pocketpc, as you can imagine this is very frustrating as I depend on my xda2 to receive and make phone calls I would be very grateful any members know of any way to get around this problem. I must say I am a bit concerned a try and tested xda2 update has led to this problem.

Just run the update .exe file again with the XDA docked and it should just install the update again. It happened to my mate on Saturday with his XDA II and he just ran the program again.

Dave,
done as you said and all went thru fine you are a star thanks mate.

No problems it's good as a newbie to be able to actually help people.

upgrade xda2 rom ver 172187 dead os--connection error
i was trying to upgrde the rom from o2 website when error occured at stage 19% completed asking me to reset the xda2 . when i am trying to reset the xda 2 it does not boot it just shows the o2 screen with red letters of the version and does not even charge. my laptop cannot connect to xda2 and as a result i am unable to upgrade when i tried to run the 172187 .exe again it gives error 101: connection error
please help me out of this? thanks

Related

GSM ERROR !!

:roll:
i reaaly feel depressed .. & that is coz when i was tring to upgrade my T_Mobile Radio to RU 6.24.00
that i downLoaded from http://www.romanweb.com/yorch/
my mobile gave me the messge of that the upgrade failed ...
keeping repeating restarting ..upgrading process progress for several times ...then i ting i did restart or something like that after that I think my device Died no longer working all what i could see is T)mobile start screen with the ROM vervion RT Lower Courner U above it & some letter above them without vervions #s!!! !!!.
I did reset+ON/OFF Botton pressing ... got into the WALLBAY Bootloader V5.15. then .............................. WAIT...
then i resseved the messege GSM ERROR.
I restarted same as before +on/off .
Recieved same message then Pressed RT Upper Botton got into FLASH TOOLS selected GSM ROM TO SD got the messege
SD Backup
==============
Please
connect rs232
and run PC Monitor
Now
in your sitle this messege is followed by
SD BACKUP
=============
Please
connect rs232
and run
PC Monitor
Now
We're not yet sure how to use this to dump the GSM ROM.
..... End.
Now ,,, what sould i do to recover my T-Mobile ....
GSM Error, 1% failed, and battery not charge
That was what happen on my XDA too. I've been upgrade, downgrade both OS and RS roms with my XDA for about 9 mos without any trouble until last week when I tried to upgrade RS from ATT A20.10 to TMO 6.24.01, the upgrade failed and now I am stuck with 1% failed problem. Worse, the battery is not charged any more causes any further upgrade fail. I still can upgrade/downgrade the OS rom but do not know how to fix the Radio stack.
I have tried virtually all suggestion on this forum: the 4 RS files upgrade, SD nb1, nbf upgrade, repair.zip, Programme A, programme B, different OS and RS roms upgrade/downgrade. None worked.
I even opened the XDA and connected wires. Still not working.

Help / Advice Needed Regarding o2 Rom Upgrade for XDA IIi

Hi,
I am in the process of upgrading my rom using the rom upgrade from the o2 www site.
Its been stuck on the
'checking the information on your device....Please wait.....Please do not disconnect your device from the PC or power supply until the upgrade is complete'
window for some time now. I dont know if its hung / crashed or in the middle of upgrading.
I dont want to chance it by removing the unit from the sync cradle but at the same time i dont wanna just leave it there for hours if its not doing anything.
Can anyone help ?
Steve
ps - the window I am speaking about came after the big window stating what your current rom / radio stack was and what they would be updated to giving you the option to click 'update' or 'cancel' I chose 'update' and got the message which I described earlier
Try this on a different PC...I'm assuming the phone itself is still functioning.
I had this a while back with the XDA2 and found that by attempting the upgrade on a laptop I had, it worked great without the hang.
I would then remove ASync completely (including registry items) and then reinstall it.
Cheers
Ant
I had this happen, I just shut down and restarted the installer program

Error 260 on upgrade attempt

I have successfully installed Hard SPL into my HTC TyTN (Qtek 1.18.255 ROM) but I cannot get the ROM upgrade utility to work. I have tried using both the latest Qtek 2.11.255 ROM as modified for Hard SPL and using the upgrade utility as shipped (which I know would replace Hard SPL).
In either case the process stops at the point where I get the progress bar, I get through the verifying the information on your phone screens and confirming the ROM image but it never gets past the "Updating the ROM image on your PDA Phone" box.
The progress bar remains at 0% and eventually I get the message:
ERROR [260] : CONNECTION
The Update Utility cannot connect to your PDA Phone. Please check that your USB cradle/ cable is connected...
Needless to say the cable is connected but I notice that Activesync has disappeared at this point. There is nothing to do but exit the upgrgade. When I do, Activesnc reappears
Has anyone else come across this issue?
Help would be much appreciated
Simon

Newbie but I hope not !!! help btw !!!

I own a new blue angel...called by O2 II's
So, after i read ,again,and again...I have successed enter boot loader.
With white screen it's shown the version 2.07 and the line at the top "Serial"
(uhm, i use WM2003SE as the original pda when i purchase)
Ok, the problem now is, i can't flash anyrom (in Wiki and any rom i found)
After the line appear "Don't plug cable or craddle of ...." it's seem to verifie it's self... and then the line appear again "this tool is not support for this device".....and some error like that.
I was totally confused, how i made the thing go wrong? or just i missed something???
i make a soft reset, then hard reset and then 3 button together to get the white screen with no light, still see words such as: serial, version 2.0.7...
When i plug the usb cable , then the serial change into USB as usual.
As my experience,( Dopod810 and Qtek S200) everything is normal...
One problem too, i can't connect to PC with activsync (i tried any versions as possible)but itself avaiable on Boot loader...
All you understand what happen with me???
Please help me out of this. I want my Blue Angel is not the worst i got ...(i think it's possible go up to wm6???)
Finally, thanks you all for listening( reading this topic)
Yep, Happened to me too. Heres the fix.
The regular WM6 exe will give you an error everytime with the O2 IIs. Finally I printed out the WM6 directions, and also the Blue Angel for beginners and some other threads and found the answer.
You are in the right place (stuck in bootloader that is). Now you should be ready to load the OS. In the Upgrade folder you will find:
"MaUpgradeUt_noID.exe"
Run it and you will see the progress bars on the Windows screen and the dark XDA screen. Don't bother it - allow it to complete.
After it completed, I was unable to restart, soft reset, hard reboot. I think I actually had to take the battery off. When I powered it again I saw the Color Bars and knew it was good.
Good luck, Be careful. Try to be calm. I know when I was stuck in between Roms I was close to being a nervous wreck.
erh, one more message when i fkash rom...
This MaUpgradeUT novid erh something like this but this
" This tool is not support for my device" or somehow ...
I think i really stuck...
when itself verifie version of rom , i can't see both version appear on windows.
ie : version rom which is in PDA and version of rom which is in the OS i next to flash(want to flash).
So Confused . Anyway, thank for helping !!!
You are close!
Yea,
I Kept getting that too. Couldn't see both versions. Got a couple of different error messages. you are right where I was. you've got to find the upgrade exe. in one of the folders. My IIs was stuck in bootloader and I started that upgrade and it skips checking the IIs first and just begins to xfer the data.

How can i Solve Brick Mode O2 XDA 3

Hi
My device has a German ROM.
I tried to Rom Upgrade to my O2 XDA III PDA but it doesn't work!
when i flashing the device it's freeze on process at%41 and give a error message. i unplugged the device craddle and flash same ROM again and process completed succesfuly. After all when i turn on my device ,there is only 3 Color on screen (Blue - Green - Red) and at the bottom of device is white. it writes R.1.10.00 at the right bottom of the screen.
Sorry about my english ! i searced it on web but i found a information and it tells find same type device and update ROM with FAT 32 Formatted SD Card.
Can anybody help me for Solve This Problem.
Thanks.
1. do you use vista/7 ?
2. did you forget to take out the sim and sd card during flashing?
that would be 2 possible reasons why you had the error in the first place.
now for the solution: if the flash was really complete and successful, which at this point you cannot tell by the success message, have you performed a proper hard reset?
the instructions on how to do that are to be found here: http://wiki.xda-developers.com/index.php?pagename=BlueAngel_WM5_For_Beginners
power+reset, record+camera, then set the menu options to No, Yes, Yes confirm with the mail button.
rom upgrade through the sd card is generally not such a good idea, since it has never been fully confirmed, that and how it works.
if the hard reset does not solve your problem, you should read -=this=- really carefully and think whether you really did ALL the steps, they are all equally important.
Problem is getting worst !
Thanz chieff for your Help.
Problem is getting worst and confusing. i updated Radio version to 1.10.00 to 1.15.00. Device is turn on but it doesn't boot. My Device has no camera. When i plug it to creaddle it's orange led is ligthting and randon times it boots and 3 Colored screen shown. R.1.15.00 D.****** G******
HTC Blue Angel Windows Mobile 6.1 WWE only. But now it's do nothing. This morning i made hard reset to device and shown SERÄ°AM V.2.07 and put ,t to creedle and tried to Urgrade room but it gives error random positions etc. %54 or %89. ERROR 112
is my device dead???
Thanx you very much for helping me.
(Sorry About My English )
About my OS
i tried to upgrade XP Pro (SP2). Vista and Windows / is Not permission to upgrade...
if you're giving up, mail it to me. i should be able to tinker with it.

Categories

Resources