:roll:
i reaaly feel depressed .. & that is coz when i was tring to upgrade my T_Mobile Radio to RU 6.24.00
that i downLoaded from http://www.romanweb.com/yorch/
my mobile gave me the messge of that the upgrade failed ...
keeping repeating restarting ..upgrading process progress for several times ...then i ting i did restart or something like that after that I think my device Died no longer working all what i could see is T)mobile start screen with the ROM vervion RT Lower Courner U above it & some letter above them without vervions #s!!! !!!.
I did reset+ON/OFF Botton pressing ... got into the WALLBAY Bootloader V5.15. then .............................. WAIT...
then i resseved the messege GSM ERROR.
I restarted same as before +on/off .
Recieved same message then Pressed RT Upper Botton got into FLASH TOOLS selected GSM ROM TO SD got the messege
SD Backup
==============
Please
connect rs232
and run PC Monitor
Now
in your sitle this messege is followed by
SD BACKUP
=============
Please
connect rs232
and run
PC Monitor
Now
We're not yet sure how to use this to dump the GSM ROM.
..... End.
Now ,,, what sould i do to recover my T-Mobile ....
GSM Error, 1% failed, and battery not charge
That was what happen on my XDA too. I've been upgrade, downgrade both OS and RS roms with my XDA for about 9 mos without any trouble until last week when I tried to upgrade RS from ATT A20.10 to TMO 6.24.01, the upgrade failed and now I am stuck with 1% failed problem. Worse, the battery is not charged any more causes any further upgrade fail. I still can upgrade/downgrade the OS rom but do not know how to fix the Radio stack.
I have tried virtually all suggestion on this forum: the 4 RS files upgrade, SD nb1, nbf upgrade, repair.zip, Programme A, programme B, different OS and RS roms upgrade/downgrade. None worked.
I even opened the XDA and connected wires. Still not working.
Dear Fellow Forum Members,
Followed instructions as per Xda_II_Upgrade.pdf, during installation got to a section where I got a message saying that the current rom is being erased a task bar was displayed which increase's in percentage as the job goes through. However the job was still at 0% completion when an error message was displayed saying the job had failed and the device needed to be undocked and a soft reset performed and then re-docked and to restart the process again. After performing the undocking of the device and software reset I get a message on the screen serial V1.0.1 when connected to the cradle the message changes to USB 1.01 and I cannot do anything else the unit does not boot into pocketpc, as you can imagine this is very frustrating as I depend on my xda2 to receive and make phone calls I would be very grateful any members know of any way to get around this problem. I must say I am a bit concerned a try and tested xda2 update has led to this problem.
Just run the update .exe file again with the XDA docked and it should just install the update again. It happened to my mate on Saturday with his XDA II and he just ran the program again.
Dave,
done as you said and all went thru fine you are a star thanks mate.
No problems it's good as a newbie to be able to actually help people.
upgrade xda2 rom ver 172187 dead os--connection error
i was trying to upgrde the rom from o2 website when error occured at stage 19% completed asking me to reset the xda2 . when i am trying to reset the xda 2 it does not boot it just shows the o2 screen with red letters of the version and does not even charge. my laptop cannot connect to xda2 and as a result i am unable to upgrade when i tried to run the 172187 .exe again it gives error 101: connection error
please help me out of this? thanks
Hi guys
Tried to install the following upgrade:
MagicianRadio_1.13.00_maupgrade,
but failed miserably. MDA crashed completely. The only thing the display shows is the text "serial V1.00" or "USB V1.00" depending on the presence of a USB cable...
What can I do? The thing won't even reset, and I tried both soft and hard reset. Or is there another way to reset?
Will it help if I wait until the battery runs out?
Any help is very welcome!
Find someone ntrw'ing his ROM from SD to hard disk, send it to you and then you ntrw it back onto your SD and the reboot and "press power to flash"
Chatty said:
Find someone ntrw'ing his ROM from SD to hard disk, send it to you and then you ntrw it back onto your SD and the reboot and "press power to flash"
Click to expand...
Click to collapse
Thanks Chatty, but sorry, I don't understand "ntrw".
And are you saying that the MDA will boot from the ScanDisk Card? Like a bootdisk for a pc?
I have some more information now:
Every now and then this text "Serial" or "USB" disappears. When this happens and I switch on the MDA, it reboots, like when I first got it. But then without completing the boot, the screen switches to black again with the text "serial" or "USB".
I'd appreciate your help.
If you'd dare to use this board's search function you'd know by now that ntrw is a program to read/write SD cards on a low level.
And you don't boot from SD card - it just contains a ROM if you were following my 'guide'. The bootloader from your PDA is able to read that format and flash it´to your chips holding the ROM. Please do some reading first... it's stupid to write the same stuff over and over again.
You're right.
I use other forums and hate it when people do this. I'm actally quite surprised I do it myself now...
I suppose it feels like the most logical thing to do when something tries to help out: to ask the same person what it is s/he means. Doesn't make it right though.
Anyway, back to the point.
I got it to work in the end without any SD or whatever. I can't really put my finger to what went wrong at first, but it works now, so i'm glad.
Hi,
I'm using Artemis with one of Tom's ROM. The device was working well. But today suddenly the device won't start up - it is locked at the startup screen showing the SPL, IPL etc. I can enter the bootloader.
Can anybody tell me how to flash the ROM at this stage?
Flash from bootloader
Hi!
Please download an official rom and keep pressed the Power and Record buttons. You will see a screen with 3 colors (red green blue). Connect the USB cable and wait for Activesync. After this start the original rom flasher and follow the instructions. If you can start the Windows, you should flash the USPL again and you can flash cooked roms. If you flashed a new one, i think you should also upgrade the radio rom.
Sorry for my English
well i'll give it a try.
BTW will activesync work if the phone is not booting up?
sure it will, but make sure you have the only phone pluged in, nothing else, and disable all firewalls and antivriuses.
Good luck
i flashed with htc official rom and it worked first. after soft resetting a few time (due to program installation) the phone again back to earlier state.
it is showing:
ipl 3.13.0001
spl 3.13.0000
gsm 2.94.90
os 3.13.0.0
and stuck at this screen.
i tried to update the phone again with the same rom - but i'm getting error 270.
do i need to unlock cid before flashing?
but i can't use the uspl tool as i can't connect to activesync.
pls help.
make sure the battery is fully charged again.
Restart your PC, isbale ll antivirus and firewalls
Better if flashing in XP PC
put PPC in Boating status
Flash Shipped ROM
Specify which software caused you the trouble and do not install it again
CID unlock PPC
Flash any cooked ROM.
once i flashed the phone with the shipped rom successfully. The phone was CID unlocked then. But now when I try to flash the shipped again i'm getting an error message (error 292 or something - stating-invalid vendor id)
archat68 said:
once i flashed the phone with the shipped rom successfully. The phone was CID unlocked then. But now when I try to flash the shipped again i'm getting an error message (error 292 or something - stating-invalid vendor id)
Click to expand...
Click to collapse
you must unlock phone again.
I tried flashing the device with factory shipped ROM. but i'm getting Error 294-invalid vendor id message.
please suggest what to do?
chance are you have stuffed your bootloader...
start from scratch again by running uspl:
http://forum.xda-developers.com/showthread.php?t=311403
than flash your favorite rom again, ideally via sd-card-flashing:
http://wiki.xda-developers.com/index.php?pagename=Artemis_SD_Card_Flashing
greetz
thormdac said:
chance are you have stuffed your bootloader...
start from scratch again by running uspl:
http://forum.xda-developers.com/showthread.php?t=311403
than flash your favorite rom again, ideally via sd-card-flashing:
http://wiki.xda-developers.com/index.php?pagename=Artemis_SD_Card_Flashing
greetz
Click to expand...
Click to collapse
USPL needs activesync running. Can you tell me how to run USPL when I can't boot into windows?
well,
its been some time, but i am pretty sure uspl puts your device into bootloader and operates from there...
have you tried setting it into bootloader, connecting via usb and simply starting uspl?
running a normal setup-routine, there is no need to start it from wm either-simply put it into bootloader and start setup!
greetz
Well i tried that. But it seems that USPL doesn't work without activesync.
i've also tried flashing with SD card, but after a brief "Checking SD card content" message the phone goes back to bootloader.
Someone helpppp pls.
are u sure your sd card is correctly configured, according to the wiki entry- especially part "if above fails" ...?
if all steps fail, assumed you performed them correctly, you might try taking out battery and leave the device fully without power overnight...and restart it the next morning
I've used a 512MB SD card - formatted it- and copied the OS file as ARTEIMG.nbh - put the sd card in the phone and started the phone in bootloader mode.
I think there is nothing more to do.
I can enter the bootloader, connect the phone to PC in USB mode. So, I hope that my phone is not bricked.
But how to revive it?
if you are in bootloader, i dont see why you shouldnt be able to flash!!!
try another sd-card, use another xp computer, exchange the usb cable...
yust to be certain: have you left out battery over-night?
...and what are the details stated on boot-loader screen (numbers)?
oh, and I get the feeling you are not working exactly as told:
in your PC right-click on Computer, then select Manage
Select Disk Manager and then delete existing partition
create a new partition with max size 256MB
format this partition in FAT32
thormdac said:
(i)...and what are the details stated on boot-loader screen (numbers)?
(ii) oh, and I get the feeling you are not working exactly as told:
in your PC right-click on Computer, then select Manage
Select Disk Manager and then delete existing partition
create a new partition with max size 256MB
format this partition in FAT32
Click to expand...
Click to collapse
(i) See post no 5 for the details
(ii) You can not do this with a removable disk (SD card inserted through a card reader). Only works when you can get WM5Storage to work.
archat68 said:
(ii) You can not do this with a removable disk (SD card inserted through a card reader). Only works when you can get WM5Storage to work.
Click to expand...
Click to collapse
...i dont have my micro-sd-card-adapter at hand atm., but there sure will be possibilities formatting your sd card accordingly...try administrative tools/computermanagement/storage/diskmanagement under xp, boot your pc with a diskpartitioner like acronis disk director...
i can only advise you to keep trying...but as long as you can not say for sure sd-card-flashing is working correctly, i wouldnt give up...
and as far as flshing bootloader via usb/activesync goes, i can only say i once screwed my device due to insufficiant battery power during sd-card-flashing and thought it was bricked just at the point you are stuck now!!! - totally resetting it with the power-oiut-method, i.e. battery out overnight, revived it!!!
than agin i sure as hell did everything the way it was ment o be done...and nothing worked until i switched to another pc/ usb-cable!!!
so, to sum it up, DONT GIVE UP!!! bootloader is showing...so there must be a way to get this to work...
greetz
archat68 said:
I tried flashing the device with factory shipped ROM. but i'm getting Error 294-invalid vendor id message.
please suggest what to do?
Click to expand...
Click to collapse
Somebody please help me to revive my phone.
how can we help you, if you dont provide us any results of the steps suggested to you...ideally in a way so we can see what you actually did or didnt do, precisely as told ?!?
greetz
Hi
My device has a German ROM.
I tried to Rom Upgrade to my O2 XDA III PDA but it doesn't work!
when i flashing the device it's freeze on process at%41 and give a error message. i unplugged the device craddle and flash same ROM again and process completed succesfuly. After all when i turn on my device ,there is only 3 Color on screen (Blue - Green - Red) and at the bottom of device is white. it writes R.1.10.00 at the right bottom of the screen.
Sorry about my english ! i searced it on web but i found a information and it tells find same type device and update ROM with FAT 32 Formatted SD Card.
Can anybody help me for Solve This Problem.
Thanks.
1. do you use vista/7 ?
2. did you forget to take out the sim and sd card during flashing?
that would be 2 possible reasons why you had the error in the first place.
now for the solution: if the flash was really complete and successful, which at this point you cannot tell by the success message, have you performed a proper hard reset?
the instructions on how to do that are to be found here: http://wiki.xda-developers.com/index.php?pagename=BlueAngel_WM5_For_Beginners
power+reset, record+camera, then set the menu options to No, Yes, Yes confirm with the mail button.
rom upgrade through the sd card is generally not such a good idea, since it has never been fully confirmed, that and how it works.
if the hard reset does not solve your problem, you should read -=this=- really carefully and think whether you really did ALL the steps, they are all equally important.
Problem is getting worst !
Thanz chieff for your Help.
Problem is getting worst and confusing. i updated Radio version to 1.10.00 to 1.15.00. Device is turn on but it doesn't boot. My Device has no camera. When i plug it to creaddle it's orange led is ligthting and randon times it boots and 3 Colored screen shown. R.1.15.00 D.****** G******
HTC Blue Angel Windows Mobile 6.1 WWE only. But now it's do nothing. This morning i made hard reset to device and shown SERİAM V.2.07 and put ,t to creedle and tried to Urgrade room but it gives error random positions etc. %54 or %89. ERROR 112
is my device dead???
Thanx you very much for helping me.
(Sorry About My English )
About my OS
i tried to upgrade XP Pro (SP2). Vista and Windows / is Not permission to upgrade...
if you're giving up, mail it to me. i should be able to tinker with it.