my pda2k is dead i have to upgrade the radio and now isn't possible to enter.the screen is black and "serial V. 2.07"it impossible ti reset.
Thank you
Reboot PC
Just reboot your PC, and leave the BA in the cradle. Execute the updater again, et voila, no problem...
Related
While upgrading my XDAII to the new O2 rom, I got a connection error which tiole me to disconnect the xda and do a soft reset.
I did this and it's now stuck on the O2 boot screen and wont budge, wont connect via active sync and does nothing else when I hard reset.
Have I f**ked it up ??
Please help,
Tommy
Don't panic
Just reset the device, place it back in the cradle and re-run the upgrade. It doesn't require Activesync as the upgrade process looks after its own connection.
Make sure the cradle is connected directly into a USB port on your PC and not to a hub. Also make sure the power supply is connected to the cradle.
Thanks, but that doesnt seem to help, the program just says that their is no connection.
Do you have another PC you can use? or try using a different USB port.
tried it on both and nothing, It looks like the XDAII can't start up properly and that's why it can't establish a connection. As I said it's stuck on the O2 boot screen (the one with the bubbles on it) with the version nos at the bottom and does nowt else.
I feel sick...
Tommy
OK. I misunderstood. I thought you were in the bootloader screen. So you need to see if you can put the device into bootloader mode. Press the jog button (bottom middle front of device) and power button at same time whilst pressing the reset button. This (hopefully) will put you in the bootloader - a dark screen with Serial 1.xx displayed. Then when device is put in cradle it should change to USB 1.xx. Then you can re-run the upgrade.
Whayhey
DCS you are indeed the man!
Thanks for your help.
Tommy
First of all Hello
I've been trying to update my XDA2i Pocke PC for more than an hour
and every time I start the Update Operation I got an error message and the operation corrupt agian it prompts me to reset it, after the reset, it informs me to disconnect the Pocket and Cardle USB, and reconnect it Again but it gave me a message on its screen told me Serial on the top of the screen, and on the buttom V1.01< What should I do?
Please Help me to get it alive again because it's dead now, and it won't work anymore, I need the method of booting it up, what are the buttons combinations to enter the boot again.
and If you gave the ROM Update for it, I'd be so grateful!! :lol:
PS: the Pocket information are
Pocket PC O2 XDA2i
Are you using a usb hub to connect, if you are then try plugging in direct to usb port. You will not be able to boot until you complete the flashing procedure, the program has probably wiped your previous rom.
It didn't work
Thanks sir,
but how can I do the flashing procedure, the Pocket PC wouldn't give the chance to do it!
and I've already plugged the USB directly to the PC.
Could you give the manner to falsh it again and boot,
because it is dead and silent
I'll be so grateful for your efforts
I was trying to upgrade ROM using my notebook and craddle connection with i-mate pocket pc. While upgrading notebook fell asleep. As a result connection was interrupted and finally lost. I-mate doesn't react any actions like normal or hard reset now, and there is no connection with computer.
Please tell me what to do to make my i-mate work again.
try to boot it into boot loader mode, by pressing camera , power and then pressing the soft reset "pin" on the bottom of the phone.... if it boot ... youre lucky and then connect usb, disable activesync and reflash.....
Hi i just bought a i-mate jasjar, it's a g3 device (boot shows 1.01). i just flashed ranju's rom but it freezes on wm6 splashscreen and i dont know what to do, help me please i want a wm6-6.1 ROM!!! thank you so much...
I had the same thing recently caused by not unticking allow USB connection in activesync. I tried to do it 3 times before I realsed what the problem was. I had to use MITY to reset the unit then reflashed the ROM & it was OK.
ken0150 said:
Hi i just bought a i-mate jasjar, it's a g3 device (boot shows 1.01). i just flashed ranju's rom but it freezes on wm6 splashscreen and i dont know what to do, help me please i want a wm6-6.1 ROM!!! thank you so much...
Click to expand...
Click to collapse
read the wiki, you will find all you need to instal roms with no problem
Cheers
Solution
keno0115 it was exactly my case. Here is how I solved:
First flash it back to original jasjar rom (WM5). But to do so:
1- Unhook your jasjar from your computer
2- Untick "USB Connection" in ActiveSync
3- Press light button+power button+reset button to go to bootloader mode
4- plug-in usb cable to hook up to the computer
5- Run JasJar Rom update as usual
6- Hard reset your jasjar to see WM5 is working fine
Then flash it to ranjus rom. To do so:
1- Download http://rapidshare.com/files/36286892/UNI_upgrade_issues_and_solutions.rar
2- Extract Country_Id_Error folder under Rom Unlock folder
3- Extract Ranjus's rom (or any other WM5 or 6 or 6.1 rom) to a folder
4- Copy nk.nbf to the extracted Country_Id_Error folder (step2)
5- Unhook your jasjar from your computer
6- Untick "USB Connection" in ActiveSync
7- Press light button+power button+reset button to go to bootloader mode
8- plug-in usb cable to hook up to the computer
9- Run MaUpgradeUt_noID.exe from Country_Id_Error folder
10- After flashing finished do a hard reset. And wait 2 or so minutes to calibration screen come up.
11- Tick back again "USB connection" in ActiveSync, to use activesync again
Hope that helps.
alpusm
Hi every one,
i have a serious problem with my HTC I-MATE JASJAR what's blocked in white screen (Serial / USB) and i cannot do anything on it, no boot, no reset soft, no reset Hard, no upgrade.
The issue is related to:
I tried to upgrade Radio ROM from 1.09.00 to 1.12 and i'm using Windows 7 Pro and when starting Flash, my PC shutdown because an electrical issue and since that, i cannot boot my device, i cannot flash or reset, my device is hung on white screen with Serial when no USB cable bluged in the PC and USB when Cable is pluged.
I Tried many times to boot it but no response, it's still hung and nothing can move on it.
I Just have one detail: when i plug the USB cable in my PC, the device is reconised but when starting upgrade or flash, i have error 101, no connexion.
Plz someone help me :crying::crying::crying::crying::crying::crying: