My truck is a bit older so I didn't have any factory steering wheel controls.
With my previous pioneer units I was able to use an aftermarket steering wheel control that had a 3.5mm jack that plugged into every other radio I've had over the years. But my new PX6 unit doesn't have a 3.5mm jack....
Is there a specific wires on the Dasaita units that need to be connected to my 3.5mm wires? I can chop the end off if needed but I honestly have no idea what wires do what.
Am I wise to purchase different steering wheel controls?
For what it's worth, I was using this before with my other stereo https://axxessinterfaces.com/product/ASWC-1
What kind of " aftermarket steering wheel control" do you have ?
I think you can use it by connecting the "tip" of the jack to SWC (Key) of navigation, and the ground of the jack to the ground wire of navigation ...
Related
Hello all, I have a Chevy Malibu and I wanted to use the steering wheel control on my eonon GA2114. I have wired ASWC-1 but it didn't give any signal in the learning mode. Any ideas? Anyone did this on GM cars? Thank you.
I am also trying to figure this out, I got a PAC-rg5-gm11 interface which has a blue wire and a 3.5mm headphone plug to retain steering wheel controls, but not sure how to hook that up to the key1 5v, or key 2 5v, none seem to work.
Any luck on this yet? I'm in the same boat with my jeep. Trying to figure out the wiring before everything gets here. The PAC unit has 1 headphones looking jack and 1 blue wire. The eanon radio I'm getting has 2 swc data wires.
dbshane said:
Hello all, I have a Chevy Malibu and I wanted to use the steering wheel control on my eonon GA2114. I have wired ASWC-1 but it didn't give any signal in the learning mode. Any ideas? Anyone did this on GM cars? Thank you.
Click to expand...
Click to collapse
Some basic info here: http://forum.xda-developers.com/and...el-control-t3329989/post65686983#post65686983
using search.
pyraxiate said:
Any luck on this yet? I'm in the same boat with my jeep. Trying to figure out the wiring before everything gets here. The PAC unit has 1 headphones looking jack and 1 blue wire. The eanon radio I'm getting has 2 swc data wires.
Click to expand...
Click to collapse
If you cut off the headphone jack you should have two wires red and black (or possibly white) just connect the red one to one of the key wires (I used key1) on the radio harness.
I just figured that out. Set the canbus to pioneer and it worked perfectly. Wish I saw this post earlier today lol
Sent from my SM-N900T using Tapatalk
Local driving laws are changing, so I can't touch my android phone while on the road. I'm looking for a way to skip music tracks forward or back. Note my car cigarette lighter jack is broken, and I'm using a 3.5mm audio cable from my Nexus 5 headphone jack to AUX IN on my car stereo.
I'm looking for an inexpensive and very easy to set up solution. Currently I've only found this:
http://www.amazon.com/iSimple-Portable-Wireless-Smartphones-Bluetooth/dp/B00KPZN5UC
At $30 it looks overpriced for a cheap Chinese product. Are there better or cheaper solutions out there?
Thanks
I have a Seicane headunit and it has inputs for CAN HI and CAN low. If I connect these straight to the Canbus could I pull the OBDII data from the car? or is a CANBUS decoder required? I don't need it for steering wheel controls or anything else. I would just like to see some OBDII data.
Head unit is a PX5 4gb+32gb
If you're talking about the 2 pins on the harness connector that goes to the car those 2 wires go to another smaller connector that plugs into the CANbus decoder. So yes you need a CANbus decoder but those ELM327 OBDII dongles are dirt cheap.
Hello,
I just recently had a Dasaita Max6 installed in my 2014 Fiat 500. What adapter do I need to make steering wheel controls work? Thanks!
Hi everyone,
I am trying to get my steering wheel controls working for my 2013 Volvo XC60. I purchased a P5 unit from Seicane and updated it with HAL9K Mod V4, which made the unit very stable with no issues. The only problem I am having; which I had before the update, is that I cannot get my steering wheel controls to work. The unit came with what looked like a CANBUS connector as part of the harness, but no box. Looking at my Volvo wiring diagram, I only have one wire for steering wheel control. When I connect that wire to KEY 1 or KEY 2 and try to program a button, it randomly ask me to select a function to assign a key.
Going through the wiring, the harness creates a bridge with the wiring harness for the information screen. It bridges off three connectors to the stereo harness and the connector that looks like its for a CANBUS BOX. The three wires are 2 CANBUS lines and a line that goes to the steering wheel remote. Since my vehicle is 2013, I think that i would need a CANBUS decoder box and that the unit should have come with one. Again, if its not needed, the only thing I can think of is bridging the lines from the CANBUS lines & steering wheel control wire that pull from the vehicle directly to the head units 2 CANBUS input lines and the KEY 1.
Sorry if this is confusing. Just seeing if there is something I am missing.
Please let me know if there are any details that I did not provide that would help solve the issue. Thank you.