Hello guys, so I have this Galaxy Grand Duos I9082 with what appears to be a soft brick, so I got it in Download Mode, got a stock ROM and tried to flash it with Odin but it keeps failing. I tought I was not using a proper stock ROM but since there are no roms for my region (South America) I was using a Spain region rom. Does this has anything to do with the failure? My galaxy is the international version I think.
I used 4.2.2 and 4.1.2 with no success. Also I used the .pit file and still no success.
Changed USB cable, USB port, but Odin still fails at flashing.
What do I do now? I think I'm in a dead end now
LOG:
<ID:0/017> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> I9082XXAMF3_I9082OXXAMF1_I9082XXAME1_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/017> Odin v.3 engine (ID:17)..
<ID:0/017> File analysis..
<ID:0/017> SetupConnection..
<ID:0/017> Initialzation..
<ID:0/017> Set PIT file..
<ID:0/017> DO NOT TURN OFF TARGET!!
<ID:0/017> Get PIT for mapping..
<ID:0/017> Firmware update start..
<ID:0/017> sboot.bin
<ID:0/017> NAND Write Start!!
<ID:0/017> FAIL!
<OSM> All threads completed. (succeed 0 / failed 1)
Thanks a lot in advance folks.
"Solved"
Since none of you guys here could give me an answer I took the phone to Tech Support (it was his fate) and it has the eMMC Chip damaged so it needs a replacement. If anybody is having the same problem then this may be the reason.
I post this so everyone knows in case you're getting trouble with flashing your Grand.
So, "problem solved"
no power. please help.
after flash the rom v37. it black out..
what should I do? please help me.. thanks
mCryMe said:
after flash the rom v37. it black out..
what should I do? please help me.. thanks
Click to expand...
Click to collapse
Are you able to boot into recovery? If so, your phone is soft-bricked. Simply restore a backup of a working ROM. ?
Related
I've just lost my Samsung note, after a hard reboot when the phone locked I got a dead system. Tried to boot into the reset menu but got the Odin menu by mistake, after which I hard reset the phone again, but this time it won't boot past the SGN2 Boot screen. I've gone through all the stuff of trying to re-install the phone with a ROM but it moan I had no PIT, so I found one. Still though it won't go past in setting of the partition... it might need a long time to set-up, but I have no idea as after a hour its still leaving the same message. I'm going to leave it overnight, but I would love some feed back to those that have done this before.
Last status in Odin3 -
<ID:0/011> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> root66_VZW_stock_system.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/011> Odin v.3 engine (ID:11)..
<ID:0/011> File analysis..
<ID:0/011> SetupConnection..
<ID:0/011> Initialzation..
<ID:0/011> Set PIT file..
<ID:0/011> DO NOT TURN OFF TARGET!!
<ID:0/011> Get PIT for mapping..
Well I left it running over night and still nothing... So far I have tried it with PIT_N7100_16GB_20121102 and it just never gets any further. So I can only assume that I'm making a mistake getting this on the system. Going to have another search later to see if their are any other methods of restoring the phone.
It's really bad sign and I suspect SDS
Can you give more details what exactly happened, how the issue started?
You are on which rom, when this happened?
Sent from my GT-N7100 using xda premium
dr.ketan said:
It's really bad sign and I suspect SDS
Can you give more details what exactly happened, how the issue started?
You are on which rom, when this happened?
Click to expand...
Click to collapse
The phone is completely stock, which it why this has rather confused me. All I know is that it was working all OK, hun and wouldn't respond, so I reset it with a battery pull. On starting it up the phone wouldn't move past the 'Samsung' boot screen. So I tried to boot into the recover to reset the system and end up in the Odin mode by mistake, but since then the phone now won't move past the SNGT-7100 Screen. Plugging it into Odin and trying to install the stock ROM again it told me I had no PIT, so I have tried to apply a number but they all fail.
<ID:0/012> Odin v.3 engine (ID:12)..
<ID:0/012> File analysis..
<ID:0/012> SetupConnection..
<ID:0/012> Initialzation..
<ID:0/012> Set PIT file..
<ID:0/012> DO NOT TURN OFF TARGET!!
<ID:0/012>
<ID:0/012> Re-Partition operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
I've tried the PIT_N7100_16GB_20121102.pit and sch-i605-16gb.pit
I'm rather stuck as to whether there is another method I can try or should just give up and take it back to Phones4u to get it replace via the warrenty as I've only had it since just before Xmas.
It seems SDS purely, don't do anything, particularly which raise flash counter and just submit to service centre.
Sorry man but it's seems nothing but SDS, you may not have updated to latest 4.1.2,which believed to have fixed for it
Goodluck
Sent from my GT-N7100 using xda premium
I'm just reading up on SDS... thats rather annoying. Well off to Phone4u then. Thanks for your help.
On which rom were you before all this happened?
Sent from my GT-N7100 using xda app-developers app
I have the same problem on stock rooted rom. Phone was working perfectly. Retarted and now nothing
<ID:0/003> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> BOOTLOADER_N7100XXDLJ2_422394_REV00_user_low_ship.tar.md5 is valid.
<OSM> CODE_N7100XXDLJ2_422394_REV00_user_low_ship.tar.md5 is valid.
<OSM> MODEM_N7100XXDLJ2_422394_REV00_user_low_ship.tar.md5 is valid.
<OSM> CSC_XEF_N7100OXADLJ2_422394_REV00_user_low_ship.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/003> Odin v.3 engine (ID:3)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Set PIT file..
<ID:0/003> DO NOT TURN OFF TARGET!!
<ID:0/003>
<ID:0/003> Re-Partition operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
Sds
Sent from my GT-N7100 using xda premium
Good day, guys! Sorry if my first post is related to a problem. I'm pretty new to Android so please bear with me...
So I woke up this morning and my Note 2 won't completely boot, it goes as far as "Samsung Galaxy Note II GT-N7100" screen and just completely gets stuck. I tried to charge it but it just shows the empty battery icon. I left it charging overnight so I don't exactly know what happened. My phone is completely stock, rooted it before then un-rooted later. No custom ROM, no custom recovery etc.
I tried to boot to Recovery Mode but it won't let me. Luckily it can boot to Download Mode. I figured I would flash it to stock ROM since I was still at 4.1.1 maybe I would just update to 4.1.2. I downloaded the firmware from sammobile.com and used Odin but it fails every time with this message:
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> CODE_N7100XXDLJ2_422394_REV00_user_low_ship.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/015> Odin v.3 engine (ID:15)..
<ID:0/015> File analysis..
<ID:0/015> SetupConnection..
<ID:0/015> Initialzation..
<ID:0/015> Get PIT for mapping..
<ID:0/015>
<ID:0/015> There is no PIT partition.
<OSM> All threads completed. (succeed 0 / failed 1)
<ID:0/015> Removed!!
Can someone point out the problem to me? I've read around that this is probably SDS but I'm still hoping that it's not. I bought my phone from another country so taking it back would be a little difficult.
Any help appreciated. Thank you!
Hi everyone, i am trying to downgrade my samsung galaxy s3 t999 from 4.1.2 to 4.1.1 so i could UNLOCK my WIND MOBILE phone and use it with ROGERS sin card. I tried to do the process via ODIN but i am getting this message :
<ID:0/003> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> T999UVDLJC_T999TMBDLJC_T999UVDLJC_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/003> Odin v.3 engine (ID:3)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> aboot.mbn
<ID:0/003> NAND Write Start!!
<ID:0/003> FAIL! (Auth)
<OSM> All threads completed. (succeed 0 / failed 1)
I REALLY NEED TO USE THE PHONE AS SOON AS POSSIBLE !! SOMEBODY HELP ME PLEASE !!
THANKS !
numberone1 said:
Hi everyone, i am trying to downgrade my samsung galaxy s3 t999 from 4.1.2 to 4.1.1 so i could UNLOCK my WIND MOBILE phone and use it with ROGERS sin card. I tried to do the process via ODIN but i am getting this message :
<ID:0/003> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> T999UVDLJC_T999TMBDLJC_T999UVDLJC_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/003> Odin v.3 engine (ID:3)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> aboot.mbn
<ID:0/003> NAND Write Start!!
<ID:0/003> FAIL! (Auth)
<OSM> All threads completed. (succeed 0 / failed 1)
I REALLY NEED TO USE THE PHONE AS SOON AS POSSIBLE !! SOMEBODY HELP ME PLEASE !!
THANKS !
Click to expand...
Click to collapse
I do believe the firmware you are attempting to flash is not for your device. That firmware is for the SGH-T999, not the SGH-T999v. Hopefully you didn't brick your phone. Download the proper firmware and try again.
It was only the modem that you needed to flash, anyhow. Not the entire firmware package.
my phone works perfectly though, COULD you please tell me which firmware should i download then to do the downgrade ??
You gave conflicting information. You said it's a T999, but also it's from Wind. The Canadian carriers use model T999V. It is different. I'm assuming you have the T999V, in which case you simply just need to download the WIND 4.1.1 firmware for the T999V (build UVLDLL1 If I remember right). It's all in my firmware thread. Link in Sig.
And look under the battery to know what model you have.
Sent from my SCH-I535 using Tapatalk 4
Please read forum rules before posting
Questions and Help issues go in Q&A and Help section
Thread moved
Thank you for your cooperation
Friendly Neighborhood Moderator
Help Galax S3 T999V wont restart after downgrade to 4.1.1
Hello
I was trying to down-grade Galaxy S3 (T999V wind mobile) 4.1.2 to 4.1.1.
I used Odin to load the new Firmware, as soon as the phone restarted i got the following message:
"Unfortunately, the process android.process.media has stopped"
what have i done wrong and what should i do in order to fix that?
thank you in advance
Kofiko
kofikom said:
Hello
I was trying to down-grade Galaxy S3 (T999V wind mobile) 4.1.2 to 4.1.1.
I used Odin to load the new Firmware, as soon as the phone restarted i got the following message:
"Unfortunately, the process android.process.media has stopped"
what have i done wrong and what should i do in order to fix that?
thank you in advance
Kofiko
Click to expand...
Click to collapse
This is no problem
wipe you're internal storage in recovery, it's best to do a factory reset in the stock recovery including caches and reboot and enjoy a fresh stock ROM
How to flash the modem only
Aerowinder said:
I do believe the firmware you are attempting to flash is not for your device. That firmware is for the SGH-T999, not the SGH-T999v. Hopefully you didn't brick your phone. Download the proper firmware and try again.
It was only the modem that you needed to flash, anyhow. Not the entire firmware package.
Click to expand...
Click to collapse
Can you please tell me how to flash the modem?
stuck at boot logo
enter into recovery but internal memory not mounting shows only 0mb storage not evn wipe,restore,backup anything wd dt not possible
odin show me dis when m try to install new md5 file.
<ID:0/004> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> T999UVDMD5_T999TMBDMD5_T999UVDMD5_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/004> Odin v.3 engine (ID:4)..
<ID:0/004> File analysis..
<ID:0/004> SetupConnection..
<ID:0/004> Initialzation..
<ID:0/004> Get PIT for mapping..
<ID:0/004> Firmware update start..
<ID:0/004> aboot.mbn
<ID:0/004> NAND Write Start!!
<ID:0/004>
<ID:0/004> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
plzzzzzzzzz help pllzzzz
thankz in advance
What recovery are you using? Try updating it. Factory resetting almost always solves boot hangups. For Odin, try flashing a different firmware. If you ever flashed 4.3 firmware, you can ONLY flash the same or newer from now on.
DocHoliday77 said:
What recovery are you using? Try updating it. Factory resetting almost always solves boot hangups. For Odin, try flashing a different firmware. If you ever flashed 4.3 firmware, you can ONLY flash the same or newer from now on.
Click to expand...
Click to collapse
SIr i have the same Problem but a little bit different .
i can recover my Phone without Odin problem but when the phone start up the is hangup with SAMSUNG logo and nothing appear then suddenly the phone is restarting without any action .. !!!!
please what should i do to fix my phone !?
Wallid92 said:
SIr i have the same Problem but a little bit different .
i can recover my Phone without Odin problem but when the phone start up the is hangup with SAMSUNG logo and nothing appear then suddenly the phone is restarting without any action .. !!!!
please what should i do to fix my phone !?
Click to expand...
Click to collapse
What steps have you taken to try to fix it?
So, my friend updated their S4 Mini GT-I9195 to Android version 4.4.2 Kitkat. The phone shut down twice after the update and is no longer able to boot up. So they gave me it to see what I can do. I've tried going to Odin mode, Recovery. But none of it works. I've also tried using QPST, but I'm unable to find .hex or .mbn file for it. So I tried the one for the required MSM8930 chipset. Sadly, the QPST cannot connect to my phone. Is there anything else I could do to revive it without having to JTAG it or something? Please help.
EDIT: I've managed to run it in Odin mode by using debrick.img flash into SD Card, however.. after trying to flash recovery. Odin returns:
<OSM> Enter CS for MD5..
<OSM> Binary Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/010> Odin engine v(ID:3.1100)..
<ID:0/010> File analysis..
<ID:0/010> SetupConnection..
<ID:0/010> Initialzation..
<ID:0/010> Get PIT for mapping..
<ID:0/010>
<ID:0/010> There is no PIT partition.
<OSM> All threads completed. (succeed 0 / failed 1)
Click to expand...
Click to collapse
Any ideas?