Can anyone help.....
I have tried to flash a few custom roms but everytime I go to install it says installation aborted (BAD). I have downloaded the same rom a couple of times in case it was a bad download, but still get the same result. I flashed the leaked 4.3 via odin before trying to install custom roms, could this be the problem?. I am using philz recovery.
Anybody got any ideas what I'm doing wrong?.
Thanks in advance
Scotty
tuktukscotty said:
Can anyone help.....
I have tried to flash a few custom roms but everytime I go to install it says installation aborted (BAD). I have downloaded the same rom a couple of times in case it was a bad download, but still get the same result. I flashed the leaked 4.3 via odin before trying to install custom roms, could this be the problem?. I am using philz recovery.
Anybody got any ideas what I'm doing wrong?.
Thanks in advance
Scotty
Click to expand...
Click to collapse
go with a clean wipe,system included and flash the rom. make sure u verify the md5 of the rom downloaded and use latest philz version and make a backup of rom just to be safe before flashing anything, the latest philz support 4.3 flashing
shhbz said:
go with a clean wipe,system included and flash the rom. make sure u verify the md5 of the rom downloaded and use latest philz version and make a backup of rom just to be safe before flashing anything, the latest philz support 4.3 flashing
Click to expand...
Click to collapse
I did a full wipe before trying to install. Cleared cache etc. The rom I really want to install is Dr Ketan's. I don't understand how/what you mean by checking the md5??
tuktukscotty said:
I did a full wipe before trying to install. Cleared cache etc. The rom I really want to install is Dr Ketan's. I don't understand how/what you mean by checking the md5??
Click to expand...
Click to collapse
http://www.winmd5.com/ download this locate the downloaded rom file and it will calculate the md5 and then go to the link from where u downloaded v3 ketan rom u will see md5 details there just paste at the bottom and verify to see if it matches fine if not your file download is corrupt.
are u on latest philz recovery
shhbz said:
http://www.winmd5.com/ download this locate the downloaded rom file and verify it will calculate the md5 and then go to the link from where u downloaded v3 ketan rom u will see md5 details there just paste at the bottom to see if it matches fine if not your file download is corrupt.
are u on latest philz recovery
Click to expand...
Click to collapse
I'm using philz touch 4.6.4
tuktukscotty said:
I'm using philz touch 4.6.4
Click to expand...
Click to collapse
use this http://d-h.st/iII i
i hope u have n7100 international version as u wish to flash keten rom
after flashing latest philz make a backup of rom and flash http://d-h.st/fWr u lose everything from internal it will reboot back to recovery.
procced with v3 install and just wipe cache and dalvik before restart after flashing
shhbz said:
use this http://d-h.st/iII i
i hope u have n7100 international version as u wish to flash keten rom
after flashing latest philz make a backup of rom and flash http://d-h.st/fWr u lose everything from internal it will reboot back to recovery.
procced with v3 install and just wipe cache and dalvik before restart after flashing
Click to expand...
Click to collapse
I have a UK bought note 2
tuktukscotty said:
I have a UK bought note 2
Click to expand...
Click to collapse
yes that's fine if ur box says n7100 and below battery check
shhbz said:
yes that's fine if ur box says n7100 and below battery check
Click to expand...
Click to collapse
Yes defo says GT-N7100
tuktukscotty said:
Yes defo says GT-N7100
Click to expand...
Click to collapse
you are good to proceed with the link file
shhbz said:
you are good to proceed with the link file
Click to expand...
Click to collapse
I have installed the later philz recovery. Just going to try and flash again
tuktukscotty said:
I have installed the later philz recovery. Just going to try and flash again
Click to expand...
Click to collapse
Nope!.
Still unable to install. It says:
-- Installing: /sdcard/DrKetan_Custom_ROM_V3Hybrid.zip
Finding update package...
Opening update package...
E:Can't open /sdcard/DrKetan_Custom_ROM_V3Hybrid.zip
(bad)
Installation aborted
press any key to continue.
What am I doing wrong????? This is really so frustrating. Have I done something when installing the leaked version of 4.3 which is now stopping anything working??. Anybody got any ideas???.
Someone out there must know what I'm doing wrong...........please help.
shhbz said:
you are good to proceed with the link file
Click to expand...
Click to collapse
I tried and tried and tried but couldn't get it to install. I then decied to reflash back to 4.1.2 stock via odin. Then tried to install Dr's again but still wouldn't work. I then flashed the leaked 4.3 via odin and repeated the Dr's install and it worked!!!!!!.
Thanks for the advice.
Scotty.
Related
hey guys
i am not able to install custom rom .zip via CWM i don't get any error while installing, it shows "Installation complete" but later on its stuck at galaxy y logo
the other features like backup,format,etc are working fine and i am able to install .zips via stock recovery but cmw isn't working for me
PS
i was able to use cwm before to flash roms
using skins cwm
which rom were you flashing...
Sent from my GT-S5360 using Tapatalk 2
having this problem with all roms
btw
my cwm.zip size is 1.31mb
Try cwm by mad team
Do a data/cache wipe
Then again check... flashing the rom
Sent from my GT-S5360 using Tapatalk 2
dranzer006 said:
hey guys
i am not able to install custom rom .zip via CWM i don't get any error while installing, it shows "Installation complete" but later on its stuck at galaxy y logo
the other features like backup,format,etc are working fine and i am able to install .zips via stock recovery but cmw isn't working for me
PS
i was able to use cwm before to flash roms
using skins cwm
Click to expand...
Click to collapse
wipe data and cache before installing a rom... or if u hav already installed it then do a wipe data and cache... try installing something else
maybe my cwm is corrupted can anyone give me a link to the old zip ?
skin's cwm has been updated and it won't install
http://forum.xda-developers.com/showthread.php?t=1446796
and i wasn't able to find download link anywhere for madteam
http://forum.xda-developers.com/showthread.php?t=1467492
dranzer006 said:
maybe my cwm is corrupted can anyone give me a link to the old zip ?
skin's cwm has been updated and it won't install
http://forum.xda-developers.com/showthread.php?t=1446796
and i wasn't able to find download link anywhere for madteam
http://forum.xda-developers.com/showthread.php?t=1467492
Click to expand...
Click to collapse
what is your firmware sir?? maybe its about your firmware that the rom is compatible with so that it wont stuck on samsung logo or bootloop if you have that firmware like DXKL2 and DXLC1
Here you go CWM by madteam:
http://www.mediafire.com/?n3x18su3495fr8l
Also do remember to data wipe and cache wipe from both stock and CWM recoveries before installing any rom..If the ROM still doesnt flash ..use the stock rom package from dokys thread in android development and re-flash..that must fix the issue..
FuranshisuKurogawa said:
what is your firmware sir?? maybe its about your firmware that the rom is compatible with so that it wont stuck on samsung logo or bootloop if you have that firmware like DXKL2 and DXLC1
Click to expand...
Click to collapse
No firmware doesnt matter..All firmwares support all ROMS..but they may have some glitches like wifi issues etc..but atleast they will boot up
hitme987 said:
Here you go CWM by madteam:
http://www.mediafire.com/?n3x18su3495fr8l
Also do remember to data wipe and cache wipe from both stock and CWM recoveries before installing any rom..If the ROM still doesnt flash ..use the stock rom package from dokys thread in android development and re-flash..that must fix the issue..
No firmware doesnt matter..All firmwares support all ROMS..but they may have some glitches like wifi issues etc..but atleast they will boot up
Click to expand...
Click to collapse
maybe the custom rom files are corrupt he/she need to download it again....
using DDLC2 will try with madteam's cwm and report back
thanks
Guys today I tried installing MIUI v4. I followed all the steps mentioned in the thread. I installed everything properly but my phone is stuck onthe android logo. This happened when I rebooted my phone after installing MIUI. So please tell me what is the problem. Also when I am truing to restore some type of error is cropping up. Please help.
pranjaldixit said:
Guys today I tried installing MIUI v4. I followed all the steps mentioned in the thread. I installed everything properly but my phone is stuck onthe android logo. This happened when I rebooted my phone after installing MIUI. So please tell me what is the problem. Also when I am truing to restore some type of error is cropping up. Please help.
Click to expand...
Click to collapse
Before installing make backup wipe dalvik cache , cache, do factory reset and try again .. hope it helps
Sent from my Hero using xda premium
Actually I tell the whole story now. When I was making backup of my stock ROM the sd card showed low on space. So I removed that SD card and inserted the one which came with the Phone. On that I installed all the required zip files. Then I made backup of the stock ROM and the data. After that I followed these steps mentioned here -:
http://forum.xda-developers.com/showthread.php?t=1863260
According to the steps I did not did wipe davik cache etc. after instaling the ROM I did wipe factory and data reset and wipe cache partition. After following all the steps mentioned I rebooted my phone as mentioned. But after rebooting the phone is stuck on android logo. I then again went into recovery and tried to wipe dalvik cache the confirmation page that appears before wiping anything is not coming. Also when I tried to restore my phone to the stock ROM an error message is coming. So I am not able to restore to the stock ROM. This is the whole thing. So guys please help. I hope I have not bricked my phone. Any solutions?
Thanks
As long as your phone can go to recovery mode it wasnt bricked..
May i know what recovery that you use to install the rom??
Sent from my GT-S5660 using Tapatalk 2
AiphNday said:
As long as your phone can go to recovery mode it wasnt bricked..
May i know what recovery that you use to install the rom??
Sent from my GT-S5660 using Tapatalk 2
Click to expand...
Click to collapse
Mate I used latest version of ClockWork Mod to install the ROM.
pranjaldixit said:
Mate I used latest version of ClockWork Mod to install the ROM.
Click to expand...
Click to collapse
What version it is??
If you are install custom rom from stock rom,its better to use px-cwmV2..
If test it,and it minimize the risk of stuck on android logo..
After that you can change the recovery to other version that you want..
Sent from my GT-S5660 using Tapatalk 2
AiphNday said:
What version it is??
If you are install custom rom from stock rom,its better to use px-cwmV2..
If test it,and it minimize the risk of stuck on android logo..
After that you can change the recovery to other version that you want..
Sent from my GT-S5660 using Tapatalk 2
Click to expand...
Click to collapse
I think the version is 5.0.2.7. Also when I am switching off the phone after sometime it is automatically switching on by itself. So for the time being I have removed the battery.
pranjaldixit said:
I think the version is 5.0.2.7. Also when I am switching off the phone after sometime it is automatically switching on by itself. So for the time being I have removed the battery.
Click to expand...
Click to collapse
If you use that version,use the version that can support rfs+ext4 file system..
Stock rom use rfs file system and custom rom usually use ext4 file system,so therefore you have to use recovery that support both..
Sent from my GT-S5660 using Tapatalk 2
AiphNday said:
If you use that version,use the version that can support rfs+ext4 file system..
Stock rom use rfs file system and custom rom usually use ext4 file system,so therefore you have to use recovery that support both..
Sent from my GT-S5660 using Tapatalk 2
Click to expand...
Click to collapse
Could you please tell me how to proceed? Because the backup of stock ROM is showing problems.
pranjaldixit said:
Could you please tell me how to proceed? Because the backup of stock ROM is showing problems.
Click to expand...
Click to collapse
I suggest that you flash your phone to stock rom again via odin..
Then change your recovery,i was preffered px-cwmV2,but i dont know is the link still alive or not..
Flash the recovery,reboot..
Then enter recovery mode again,install rom..
Sent from my GT-S5660 using Tapatalk 2
How to do flash stock ROM as the backup that I made is not working properly.
pranjaldixit said:
How to do flash stock ROM as the backup that I made is not working properly.
Click to expand...
Click to collapse
With odin,
Search ! there are allot of guide howto flash gio to stock with odin
Sent from my HTC Hero using xda app-developers app
If you have working recovery it's no use to flash stock ROM, just flash px-cwmV2 http://www.mediafire.com/file/y1xy6g2y5tpp1fg/px-cwm-v2.zip.
Then wipe all, including dalvik, flash desired ROM, wipe all again (including dalvik), and you should be good to go.
phreak_or said:
If you have working recovery it's no use to flash stock ROM, just flash px-cwmV2 http://www.mediafire.com/file/y1xy6g2y5tpp1fg/px-cwm-v2.zip.
Then wipe all, including dalvik, flash desired ROM, wipe all again (including dalvik), and you should be good to go.
Click to expand...
Click to collapse
I hope you must have read my post about the problem. I have clockwork 5.0.2.7. The backup I made is alao showing some error when I tried to restore it using CWM. So please guide how to proceed.
pranjaldixit said:
I hope you must have read my post about the problem. I have clockwork 5.0.2.7. The backup I made is alao showing some error when I tried to restore it using CWM. So please guide how to proceed.
Click to expand...
Click to collapse
I have. As i said, you could just try CWM v2.
BUT to be absolutely safe flash a stock ROM using Odin, see http://forum.xda-developers.com/showpost.php?p=20397915&postcount=3.
After u flash the stock ROM, go to default recovery, factory reset, boot the rom, shutdown.
Flash the desired version of CWM using Odin or trough recovery, and then flash the custom ROM u want.
For me CWM 5.0.2.7 ext4+ RFS couldn't wipe dalvik, nor could it mount /system. So I used cwmV2.
Good luck!
phreak_or said:
I have. As i said, you could just try CWM v2.
BUT to be absolutely safe flash a stock ROM using Odin, see http://forum.xda-developers.com/showpost.php?p=20397915&postcount=3.
After u flash the stock ROM, go to default recovery, factory reset, boot the rom, shutdown.
Flash the desired version of CWM using Odin or trough recovery, and then flash the custom ROM u want.
For me CWM 5.0.2.7 ext4+ RFS couldn't wipe dalvik, nor could it mount /system. So I used cwmV2.
Good luck!
Click to expand...
Click to collapse
Thanks a lot. So first I have to download firmware and then using odin flash it on my phone. After that I have to install clockworkmod v2 amd then install the MIUI ROM? Can the CWM be flashed through recovery?
Thanks
pranjaldixit said:
Thanks a lot. So first I have to download firmware and then using odin flash it on my phone. After that I have to install clockworkmod v2 amd then install the MIUI ROM? Can the CWM be flashed through recovery?
Thanks
Click to expand...
Click to collapse
yes
And please tell me how to install CWM v2 as I already have version 5.0.2.7 of clockwork mod installed in my phone? Pease let me know the procedure for the same.
Thanks
pranjaldixit said:
And please tell me how to install CWM v2 as I already have version 5.0.2.7 of clockwork mod installed in my phone? Pease let me know the procedure for the same.
Thanks
Click to expand...
Click to collapse
when you flash firmware with odin, it will also flash a new recovery.
just enter recovery like normally, and flash cwm-v2.zip
after its done you pull the battery out, and boot into recovery again.
now you have clockworkmod installed
voetbalremco said:
when you flash firmware with odin, it will also flash a new recovery.
just enter recovery like normally, and flash cwm-v2.zip
after its done you pull the battery out, and boot into recovery again.
now you have clockworkmod installed
Click to expand...
Click to collapse
I am not installing firmware right now. I am just wanting to install CWM v2 and try whether it is able to install MIUI successfully or not. If this one also fails then I will install the firmwares via odin. Hope you ate able to understand what I am saying. Please help.
Hello Everyone:
I'm having a problem flashing a ROM. I'm currently on CM 11 from the N7105 forum but would like to revert back to 4.3. I'm trying to flash Skynote Air, the vanilla version. I follow the steps provided and when I try to install the zip, im being given a system 7 error and an error on the zip file. I'm using philz touch CWM by the way. Is it because im on CM11 from the N7105 or is it the zip file? When trying to download the zip file from the ROM thread, it was coming up blank and I downloaded a mirrior. Before the CM11, I was running seanzscreams Sky Note 4.3. Any and all help would be greatly appreciated.
Jestic said:
Hello Everyone:
I'm having a problem flashing a ROM. I'm currently on CM 11 from the N7105 forum but would like to revert back to 4.3. I'm trying to flash Skynote Air, the vanilla version. I follow the steps provided and when I try to install the zip, im being given a system 7 error and an error on the zip file. I'm using philz touch CWM by the way. Is it because im on CM11 from the N7105 or is it the zip file? When trying to download the zip file from the ROM thread, it was coming up blank and I downloaded a mirrior. Before the CM11, I was running seanzscreams Sky Note 4.3. Any and all help would be greatly appreciated.
Click to expand...
Click to collapse
Are you using 5.15 version of Philz ? If so, try updating it.
dicksteele said:
Are you using 5.15 version of Philz ? If so, try updating it.
Click to expand...
Click to collapse
I'm using the 6.19.3 t0lteatt version.
Jestic said:
I'm using the 6.19.3 t0lteatt version.
Click to expand...
Click to collapse
Ahhhh.. Sorry I read but didn't read. Long day.
I read it again and saw the failed downloads.
A hosed zip is probably the case.
Go here
http://forum.xda-developers.com/showthread.php?t=2589891
Try getting back to just 4.3
dicksteele said:
Ahhhh.. Sorry I read but didn't read. Long day.
I read it again and saw the failed downloads.
A hosed zip is probably the case.
Go here
http://forum.xda-developers.com/showthread.php?t=2589891
Try getting back to just 4.3
Click to expand...
Click to collapse
I wonder if anyone has a working zip then.
Jestic said:
I wonder if anyone has a working zip then.
Click to expand...
Click to collapse
Did you download from the copy.com or skynote.com?
I'm grabbing off of the Skynote.com.. Pulling Sky_Note Air Vanilla F1.zip with no problems.. Still have 5 minutes to download.
I'll know if 15 minutes if it's good.
dicksteele said:
Did you download from the copy.com or skynote.com?
I'm grabbing off of the Skynote.com.. Pulling Sky_Note Air Vanilla F1.zip with no problems.. Still have 5 minutes to download.
I'll know if 15 minutes if it's good.
Click to expand...
Click to collapse
Im getting the rom from here :
http://skynote.camattin.com/)?
It downloads with no problem. The problem is when I try to install it from recovery.
Jestic said:
Im getting the rom from here :
http://skynote.camattin.com/)?
Click to expand...
Click to collapse
Same place I just downloaded from.. Copying to phone, flashing in 5.
Only difference is I'm using TWRP as my custom recovery.
Only because personal preference... My fat fingers press buttons on Philz by mistake. I hit reboot 80% of the time before I even do anything.
EDIT: I had a copy of Philz on my phone, philz_touch_6.07.9-t0lteatt.zip. My download flashed fine.
I gotta hit the sack... Good luck
http://www.androidfilehost.com/?fid=23329332407583259
Here's what I used
dicksteele said:
Same place I just downloaded from.. Copying to phone, flashing in 5.
Only difference is I'm using TWRP as my custom recovery.
Only because personal preference... My fat fingers press buttons on Philz by mistake. I hit reboot 80% of the time before I even do anything.
EDIT: I had a copy of Philz on my phone, philz_touch_6.07.9-t0lteatt.zip. My download flashed fine.
I gotta hit the sack... Good luck
Click to expand...
Click to collapse
Interesting. Thanks for the help.
Jestic said:
Interesting. Thanks for the help.
Click to expand...
Click to collapse
http://www.androidfilehost.com/?fid=23329332407583259
Here's what I used
See my post #2361 in seanZscreams SkyNoteAir thread here: http://forum.xda-developers.com/showthread.php?p=50682717
I had same Status 7 error. In PhilZ Touch Recovery ( in version 6.19.3 which is actually 6.19.2) in Install menu, make sure you UNCHECK "Don't allow old binary update" then flash rom. You may have a corrupt data partition (I did). If so, you'll have to wipe /data/media partition. Read my post and reference links. Has to do with the change from CWM base 6045 to 6047 .
DoctorQMM said:
See my post #2361 in seanZscreams SkyNoteAir thread here: http://forum.xda-developers.com/showthread.php?p=50682717
I had same Status 7 error. In PhilZ Touch Recovery ( in version 6.19.3 which is actually 6.19.2) in Install menu, make sure you UNCHECK "Don't allow old binary update" then flash rom. You may have a corrupt data partition (I did). If so, you'll have to wipe /data/media partition. Read my post and reference links. Has to do with the change from CWM base 6045 to 6047 .
Click to expand...
Click to collapse
Thanks for the help. I just installed the latest TWRP and it flashed fine. Thanks.
Jestic said:
Thanks for the help. I just installed the latest TWRP and it flashed fine. Thanks.
Click to expand...
Click to collapse
Glad you're back up and running. .. btw, PhilZ just posted an updated CWM Touch Recovery [6.25.0] for our Note2 [t0lteatt device tree] which now automatically determines if what you're flashing has older binary code embedded in its binary-script to avoid the dreaded Status7 errors.
I'm trying to flash this ROM http://forum.xda-developers.com/showthread.php?t=2682782 on my Xperia ion over currently running paranoid ROM based on 4.1.2
After wiping data ,cache,dalvik cache in TWRP recovery when i try to flash the ROM it failed and show some error of "Failed to update partition detail" or something..
and not only this i've also tried another CM ROM and got same result .. Any step missing ??
Could anyone tell me the solution ??
Anyone could please throw some light on my problem ??
Try using ClockworkMod Recovery instead of TWRP.
How to flash CWM over TWRP ?
Mirhawk said:
Try using ClockworkMod Recovery instead of TWRP.
Click to expand...
Click to collapse
Can you give me link to innstall CWM over TWRP ..?
I think You will have to revert to stock for that and then root and install cwm. Here is the link to stock ftf, Select which ever suitable. I don't know which root works on Your device, so do check the thread for it. Then install the cwm.
Stock FTF:
http://forum.xda-developers.com/showthread.php?t=1752345
CWM:
http://forum.xda-developers.com/showthread.php?t=1830170
Mirhawk said:
I think You will have to revert to stock for that and then root and install cwm. Here is the link to stock ftf, Select which ever suitable. I don't know which root works on Your device, so do check the thread for it. Then install the cwm.
Stock FTF:
http://forum.xda-developers.com/showthread.php?t=1752345
CWM:
http://forum.xda-developers.com/showthread.php?t=1830170
Click to expand...
Click to collapse
Is there any way i can install this ROM currently directly through on over my currenlty ROM except all starting from the fresh ??
my internet connection is slow
akhil17kr said:
Is there any way i can install this ROM currently directly through on over my currenlty ROM except all starting from the fresh ??
my internet connection is slow
Click to expand...
Click to collapse
Well, You can try this app. It is an app to manage ROM and CWM, and hopefully will install CWM on Your phone.
Link
https://play.google.com/store/apps/details?id=com.koushikdutta.rommanager
Mirhawk said:
Well, You can try this app. It is an app to manage ROM and CWM, and hopefully will install CWM on Your phone.
Link
https://play.google.com/store/apps/details?id=com.koushikdutta.rommanager
Click to expand...
Click to collapse
UPDATE: I just need to flash the Kernel provided in the ROM ZIP package (Boot.img)...
How can i forget such a simple step
thanks anyways...
Hey guys,
I just rooted my p600 (wfi) and am now trying to install TWRP for my custom recovery. I can not find a good forum post about this process. I opened ODIN 3.09 and go to flash openrecovery-twrp-2.6.3.3-lt03wifiue.img which fails. Anyone know what I am doing wrong and how I can successfully flash TWRP recovery so I can start flashing my roms? Thanks guys
Dedline said:
Hey guys,
I just rooted my p600 (wfi) and am now trying to install TWRP for my custom recovery. I can not find a good forum post about this process. I opened ODIN 3.09 and go to flash openrecovery-twrp-2.6.3.3-lt03wifiue.img which fails. Anyone know what I am doing wrong and how I can successfully flash TWRP recovery so I can start flashing my roms? Thanks guys
Click to expand...
Click to collapse
Try Odin 1.85 or 3.07
lsherif said:
Try Odin 1.85 or 3.07
Click to expand...
Click to collapse
doesnt work. Tried both, cant install any custom recovery after rooting. Not sure whats the deal
Uncheck auto-reboot
Dedline said:
doesnt work. Tried both, cant install any custom recovery after rooting. Not sure whats the deal
Click to expand...
Click to collapse
http://dottech.org/151463/how-to-flash-twrp-recovery-on-samsung-galaxy-note-10-1-2014-edition-guide/
i cannot help with your problem though,
but i can give some suggestion for me i use odin v.07 because its for easy to understand and still in many tutorial use odin.07
and mostly before rooting any device you must flash a custom recovery first then go root and that's what i did.
i personally use TWRP recover yet more easy to understand and to use than cwm recovery...
it's just my opinions though...
Dedline said:
Hey guys,
I just rooted my p600 (wfi) and am now trying to install TWRP for my custom recovery. I can not find a good forum post about this process. I opened ODIN 3.09 and go to flash openrecovery-twrp-2.6.3.3-lt03wifiue.img which fails. Anyone know what I am doing wrong and how I can successfully flash TWRP recovery so I can start flashing my roms? Thanks guys
Click to expand...
Click to collapse
openrecovery-twrp-2.6.3.3-lt03wifiue.img ==> wrong file, you should use openrecovery-twrp-2.6.3.3-lt03wifiue.img.tar with ODIN
lightman33 said:
openrecovery-twrp-2.6.3.3-lt03wifiue.img ==> wrong file, you should use openrecovery-twrp-2.6.3.3-lt03wifiue.img.tar with ODIN
Click to expand...
Click to collapse
I flashed philz, then twrp, both failed to wipe cache, then I flashed philz again, and it worked. Rom is installed and working flawlessly. Not sure why the issues but thanks for the help. and I saw the mistake in download file for twrp and got the right one. Thx
Dedline said:
I flashed philz, then twrp, both failed to wipe cache, then I flashed philz again, and it worked. Rom is installed and working flawlessly. Not sure why the issues but thanks for the help. and I saw the mistake in download file for twrp and got the right one. Thx
Click to expand...
Click to collapse
With Philz, wipe Dalvik cache first, then wipe cache partition, this way wiping will function correctly.