Develop Bugs

skype on cingular 8525

Hi,
I have skype on my cingular 8525 and the signal is not clear. I can hear echos and distortions, especially when I call outside the U.S.
I checked the "echo cancellation ON" option on skype, but it's still the same.
I've heard that there's a better skype program for this phone. I'm actually running the latest version given by cingular and WM5 (for now)
Any suggestions?
Thanks a lot!

Go to SKYPE's site and download it. I use that one and make a lot f INternational calls through it. Skype via WiFi is always better than via GPRS/UMTS/3G.

They've just released a new version of Skype (2.2.0.36 I think) so give that a try.

Skype does not mention model # 8525...for Cingular/at&t...
Is it safe to install ? which one should we pick out of the 3 models supported?

The new version does work on the Hermes with voice calls!!! No support Only written messages unfortunately... Need to use the previous beta build Version 2.2.0.20. If you can't find it then I can give you the cab...

I need the Previous Version of Skype 2.1!!!
After upgrading from Skype WM 2.1 to 2.2, I managed to sign-in but noticed my skype-out account was not recognized (no credits were shown) nor did I succeed to make the echo call. Skype just crashed! When I followed the link to activate my skype-out, I got a "page not found" message!. Since I knew I had credits available, I then tried to call using the dial and it crashed as well! This is serious as I had install an old version 2.0.0.39 because my previous version 2.1 was overwritten by the new executable that I downloaded!
BEWARE OF INSTALLATION ON ANY HERMES100 DEVICE

Skype wont work on mine either but X-ten did work brilliantly with other VOIP providers that I use

is working fine only with 2.2beta, voice and data, uninstall and earase all previous versoins, reboot than reinstall this version
http://www.skype.com/download/skype/mobile/downloading_high_beta.html

will try it later...my phone hung :O
my phone wont load pas the Windows Mobile Screen...does anyone know what is wrong????

DOPOD WM6 official and VOIP problems

VOIP seems to be blocked on the new HTC official WM6 release for DOPOD.
Tried to reinstall the required dll through the usual .cab (used before roms cooks stopped removing WM6 VOIP functionalities), and the Internet Calling features appear on today's screen, however it's impossible to have the service working.
Tried the settings .cab I created (always worked with past WM6 roms) and the a program SIPconfigToll (ver. 2.0.1), but none seems to apply the settings and
always receive the same message: Internet Calling: Service Blocked. (not even the service name seems to change).
Any advice?
Internet connection is ok as well as ports, etc.

lellobello said:
Tried the settings .cab I created (always worked with past WM6 roms) and the a program SIPconfigToll (ver. 2.0.1), but none seems to apply the settings and
always receive the same message: Internet Calling: Service Blocked. (not even the service name seems to change).
Click to expand...
Click to collapse
I've installed these two cabs:
MajikVOIP.cab - http://www.4winmobile.com/forums/local_links.php?action=jump&id=24&catid=6
VOIP Drivers.cab from http://wmblack.info/addons/
And VoIP is working fine for me with official WM6 ROM.

sweet
works fine now
thanks a lot

Hi,
I install fisrt MajikVOIP.cab by double click. Let me know the way to install VOIP Drivers.cab?

double click again?
Don't forget to restart after installation

VoIP: Searching...and then...No-Service
Hi Friends:
I have a HTC TyTN with the last Official DoPoD WM6 WWE ROM 3.54.707.3...I'm trying to install the Internet Calling...here are my procedure:
1. I installed MajikVOIP.cab in my microSD
2. I installed VOIP Drivers.cab in my microSD
3. Restart
3. I installed SetupVoIP_v0.3 from Schap (it has proxy, SipConfigTool_2_0_1 doesn't have it)
4. I done my personal settings with SetupVoIP_v0.3
and the Internet Calling done the following:
Searching...and then...No-Service
Can you help me please?
Thanks
TecMan
HTC TyTN
HERM200 IPL-1.04
HERM200 SLP-2.10.01ipro 2.10.Olipro
Device Information (Upgraded 7-13-07)
ROM version: 3.54.707.3
ROM date: 07/05/07
Radio version: 1.47.00.10 (Upgraded 7-11-07)
Protocol version: 32.80.7020.20H (Upgraded 7-11-07)
Windows Mobile 6 Professional
CD OS 5.2.1437 (Build 17944.0.3.1)

eva_d said:
I've installed these two cabs:
MajikVOIP.cab - http://www.4winmobile.com/forums/local_links.php?action=jump&id=24&catid=6
VOIP Drivers.cab from http://wmblack.info/addons/
And VoIP is working fine for me with official WM6 ROM.
Click to expand...
Click to collapse
hi eva_d, I haven't permission for download MajikVOIP.cab. can you provide other link for download? many thanks!

TecMan45 said:
1. I installed MajikVOIP.cab in my microSD
2. I installed VOIP Drivers.cab in my microSD
3. Restart
3. I installed SetupVoIP_v0.3 from Schap (it has proxy, SipConfigTool_2_0_1 doesn't have it)
4. I done my personal settings with SetupVoIP_v0.3
and the Internet Calling done the following:
Searching...and then...No-Service
Click to expand...
Click to collapse
Did you try to reinstall VoIP app in device memory? Did VoIP work for you before? Do you have WiFi switched on? Does your provider/router/firewall block any VoIP ports? I would start with these things first, surely.

alexng167 said:
hi eva_d, I haven't permission for download MajikVOIP.cab. can you provide other link for download? many thanks!
Click to expand...
Click to collapse
Register an account on 4winmobile.com, and then you'll have an access. Simple as that.

alexng167 said:
hi eva_d, I haven't permission for download MajikVOIP.cab. can you provide other link for download? many thanks!
Click to expand...
Click to collapse
Try this, if they are the same files :
http://forum.xda-developers.com/attachment.php?attachmentid=43949&d=1184484873

Hi eva_d:
Thanks for your reply...let me give you my answers:
Did you try to reinstall VoIP app in device memory?
- No, I installed MajikVOIP.cab & VOIP Drivers.cab only in my microSD
- Do you recommend me to install them in device memory?
Did VoIP work for you before?
- Yes, I installed a few days ago, SJ-Labs - SJphone-PPC2003-303c and it worked fine with my VoIP provider
Do you have WiFi switched on?
- Yes, it's a basic...No-VoIP without WiFi
Does your provider/router/firewall block any VoIP ports?
- If SJ-Labs - SJphone-PPC2003-303c worked with my VoIP-Settings, I supposed that I don't have problems with block any VoIP ports
What are your recommendations to fix my problem?
Thanks
TecMan
HTC TyTN
HERM200 IPL-1.04
HERM200 SLP-2.10.01ipro 2.10.Olipro
Device Information (Upgraded 7-13-07)
ROM version: 3.54.707.3
ROM date: 07/05/07
Radio version: 1.47.00.10 (Upgraded 7-11-07)
Protocol version: 32.80.7020.20H (Upgraded 7-11-07)
Windows Mobile 6 Professional
CD OS 5.2.1437 (Build 17944.0.3.1)

always install OS specific files in main memory.
I actually store all apps in main memory and just use the microsd for data

Voip
eva_d said:
I've installed these two cabs:
MajikVOIP.cab - http://www.4winmobile.com/forums/local_links.php?action=jump&id=24&catid=6
VOIP Drivers.cab from http://wmblack.info/addons/
And VoIP is working fine for me with official WM6 ROM.
Click to expand...
Click to collapse
Can you please tell us who is your voip provider?
Thanks

alishankiti said:
Can you please tell us who is your voip provider?
Thanks
Click to expand...
Click to collapse
I'm using it with Polish ipfon.pl, however AFAIR it also worked witch sipgate.co.uk.

Mine is Messagenet. Excellent service.
www.messagenet.it

Crackling
Hi,
I've loaded MajikVOIP.cab, VOIP Drivers.cab and SetupVoIP_v0.3 (all in main memory) and although VoIP works OK, I get the occasional, short bursts of crackling from the loudspeaker, even when it's not actually enabled.
Is this a Known 'feature'?
System specs in sig.
Thanks

linker3000 said:
Hi,
I've loaded MajikVOIP.cab, VOIP Drivers.cab and SetupVoIP_v0.3 (all in main memory) and although VoIP works OK, I get the occasional, short bursts of crackling from the loudspeaker, even when it's not actually enabled.
Is this a Known 'feature'?
Click to expand...
Click to collapse
I haven't noticed that, but to be honest - I also haven't used VoIP app for a while, so I could just miss it...

linker3000 said:
I've loaded MajikVOIP.cab, VOIP Drivers.cab and SetupVoIP_v0.3 (all in main memory) and although VoIP works OK, I get the occasional, short bursts of crackling from the loudspeaker, even when it's not actually enabled.
Click to expand...
Click to collapse
I just placed VoIP call, and you're right - there is that crackling sound coming out of external speaker from time to time. However, I don't have this when VoIP is disabled. :-o
Btw, do you have the same 'feature' that changing in-call volume with roller is not possible while VoIP call?

eva_d said:
I just placed VoIP call, and you're right - there is that crackling sound coming out of external speaker from time to time. However, I don't have this when VoIP is disabled. :-o
Btw, do you have the same 'feature' that changing in-call volume with roller is not possible while VoIP call?
Click to expand...
Click to collapse
Let me try....
Confirmed, I can't change volume with the roller too.

Im in the same problem, I Black Majik and I can't get VOIP to work. Please Can some one tell me the best combination to use. thx

MMS on Three Australia with Schaps rom's

Has anyone been able to get MMS working on Three Australia??
I've been trying for the last few days and it's work with pretty much all other customized roms.. but this one is giving me issues? Maybe something to do with device identity on three servers or maybe this new version of arcsoft broke something???
I'm 100% certain settings are correct. I've tried with network setup wizard, and the following:
Gateway: 10.176.57.25
Port: 8799
Server address: http://mmsc.three.net.au:10021/mmsc
Connect via: (3 services connection, whatever it's called?) Mine is MY ISP
also tried with:
Server address: http://mmsc.three.com.au:10021/mmsc
No juice at all.. anyone else want to confirm on three Australia?? Oh and sorry about making a new thread for this.. I tried posting this in schaps thread but no response many times. I'm just looking for ANYONE to test and confirm this.

Also on Three Australia, running Schaps 3.54c. I don't usually use mms but just tried to send and it didn't work, using settings from the network wizard (checked against what I had previously sourced from aussie3g)
So it's not just you....

bigruss said:
Also on Three Australia, running Schaps 3.54c. I don't usually use mms but just tried to send and it didn't work, using settings from the network wizard (checked against what I had previously sourced from aussie3g)
So it's not just you....
Click to expand...
Click to collapse
Hey thanks for that.. just wanted to make sure I wasn't going crazy... It annoys me a bit, because I'm really REALLY loving this rom.. besides the mms thing, not one glitch and has everythign i need...

im running 3.54c and i am getting MMS with 3 Australia no issues at all. the settings are correct but as it has been posted before on other sites, you have to ring 3care and report a fault. tell them mms doesnt work just play along with them with regards to OS (stock 3 ROM) and settings.
they need to reset your 'individual profile' on the server. i had to get this done as MMS were not sending at all. it took about 3-4 days but i got fixed and MMS are working fine, send and receieve with only a minimal delay (2min max) between send and recieve.
just make sure your connect via settings has the APN 3services. Also WAP 2.0 and 300kb limit.
.... on another note 3.60a beta did not work with 3australia and the MMS settings, so i had to go back to 3.54c.....
Drooch

drooch said:
im running 3.54c and i am getting MMS with 3 Australia no issues at all. the settings are correct but as it has been posted before on other sites, you have to ring 3care and report a fault. tell them mms doesnt work just play along with them with regards to OS (stock 3 ROM) and settings.
they need to reset your 'individual profile' on the server. i had to get this done as MMS were not sending at all. it took about 3-4 days but i got fixed and MMS are working fine, send and receieve with only a minimal delay (2min max) between send and recieve.
just make sure your connect via settings has the APN 3services. Also WAP 2.0 and 300kb limit.
.... on another note 3.60a beta did not work with 3australia and the MMS settings, so i had to go back to 3.54c.....
Drooch
Click to expand...
Click to collapse
That's really strange... because the simcard and network is fine, i've tested it in other phones without issue.. i've been tru hell with mms before where it wouldn't send and then three did reset the profile and all was good. but this is a different issue and it's strange how it didn't work in the beta but it's working for you in 3.54c as techincally their both the same, it's just 3.60a beta is based on a new build of wm6.... and both are using the same version of arcsoft as well.

drooch said:
im running 3.54c and i am getting MMS with 3
just make sure your connect via settings has the APN 3services. Also WAP 2.0 and 300kb limit.
Drooch
Click to expand...
Click to collapse
Oh and one other thing I noticed... if you change to wap 2.0 so does the port number from 8799 (which it's supposed to be) to 8080 (which is the default for wap 2.0). I would double check your settings and see what their set to because it's not making much sense...

thats why the 3.60a ROM doesnt work.... it auto selects the port based on WAP version. the 3.54c version does not do this and therefore still works
Drooch

argh, why did I test this for you?! It's bugging me too now. I have the same situation where the port changes based on the wap version, running 3.54c (just checked in case I was being really stupid)
so it looks like we either have the wrong port or the wrong wap....
strange that it is working for one person.

drooch said:
thats why the 3.60a ROM doesnt work.... it auto selects the port based on WAP version. the 3.54c version does not do this and therefore still works
Drooch
Click to expand...
Click to collapse
Well actually 3.54c does do this (change the port to 8080 on wap2.0). Everyone else's post in here confirm this.
And too be honest.. i don't think that's what's causing the issues, because well wap1.2 should still work...

yes it does auto select a port number when u select the Wap version but if u overwrite it, it does not revert back to the original number, so u can select wap 2.0 and then overwrite the value back to 8799 and select ok. it should then stay on that port number.
I work in the industry and i must say that this issue only arises on cooked ROMS. i dont know if this will help but i have attached a hutchison file that was from the extrom of the dopod rom. i dont know what it contains but it may help
Drooch

drooch said:
yes it does auto select a port number when u select the Wap version but if u overwrite it, it does not revert back to the original number, so u can select wap 2.0 and then overwrite the value back to 8799 and select ok. it should then stay on that port number.
I work in the industry and i must say that this issue only arises on cooked ROMS. i dont know if this will help but i have attached a hutchison file that was from the extrom of the dopod rom. i dont know what it contains but it may help
Drooch
Click to expand...
Click to collapse
hmm.. well i'm running 3.54c and i can confirm.. if you change the port then hit ok.. go back into the settings and you'll see the port / wap version has been changed automatically for you...

well i dont know why thats happening.
did you set up a new configuration or overwrite the sample one??
ive been testing my phone since i saw this post and for some reason, if i select WAP 2.0 it will select Port 8080. i then overwrite it to 8799 and select ok.... never changes back to 8080 (unless i select WAP 2.0 again)

same happens with me, if I overwrite it will revert to the original. This happens with new and existing mms servers

drooch said:
well i dont know why thats happening.
did you set up a new configuration or overwrite the sample one??
ive been testing my phone since i saw this post and for some reason, if i select WAP 2.0 it will select Port 8080. i then overwrite it to 8799 and select ok.... never changes back to 8080 (unless i select WAP 2.0 again)
Click to expand...
Click to collapse
Are you sure your running 3.54c because outside of your post, no one else can confirm what your reporting...
Seems a bit strange...

i can confirm i am running -
ROM Version: Schap's 3.54c
ROM date: 07/05/07
Radio Version: 1.51.00.10
Protocol Version: 32.84.7020.20H
i can confirm also that this ROM can accept MMS send and recieve using 3australia with the settings that were mentioned in this post. i work for 3 and it took me 6 days of 3care communication to relsove the issue... they changed settings on their side on *my* account and now it works. the phone does not revert back to the 8080 port on *my* dopod838pro i could only get mms to work if i
a) installed the hutchison cab i posted before
b) DID NOT run the network wizard that cam with the ROM
c) entered the settings manually for connection and for MMS
d) overwrote the sample MMS settings
Drooch

drooch said:
i can confirm i am running -
ROM Version: Schap's 3.54c
ROM date: 07/05/07
Radio Version: 1.51.00.10
Protocol Version: 32.84.7020.20H
i can confirm also that this ROM can accept MMS send and recieve using 3australia with the settings that were mentioned in this post. i work for 3 and it took me 6 days of 3care communication to relsove the issue... they changed settings on their side on *my* account and now it works. the phone does not revert back to the 8080 port on *my* dopod838pro i could only get mms to work if i
a) installed the hutchison cab i posted before
b) DID NOT run the network wizard that cam with the ROM
c) entered the settings manually for connection and for MMS
d) overwrote the sample MMS settings
Drooch
Click to expand...
Click to collapse
Hmm.. thanks for all your help drooch... but i just don't see how it makes sense. I think you must be the exception. I know if I change the port to 8799 when i hit ok, and go back into the settings it's reading wap 1.2.
Also the network wizard just automates the manual input of settings, and i've looked over all the settings and can not find any differences between those and the ones listed here.
Not sure what the cab does either, but i installed it with out any luck and I've also set many times 3mms to the default connection for mms settings but it hasn't made any difference..
there is a glitch somewhere between us on three and this customized rom. I just wish I could find it already because I love the rom.

Network Wizard
I've had the same problem of WAP 2.0 selection defaulting to Port 8080 and it appears to be associated with running the Network Wizard.
I did a hard reset, entered the network settings manually then did the MMS settings - Port 8799, WAP Version 2.0, and everything worked.
So at least for 3 Australia, the advice is, don't run the network wizard, input your operator settings manually.
Cheers

finally someone that can back me up!
i assumed it was the network wizard but why??? (very weird!)
so to use 3MMS use the settings that were posted in the first post BUT DO NOT run network wizard, you must hard reset if u have used it.
Good luck,
Drooch

Ahh.. well thats some damn useful information!!!
I can't quite hard-reset my phone rite now either to test it, cuz I got too much stuff I need, but definitely handy info!!! I wonder if this applies to all roms??
And thanks drooch for your persistence In the end all we want is for stuff to work... looks like we may be getting it afterall

ROM version of AX3L and Mary Problem

I have try the ROM of AX3L and Mary and use it at China using China Mobile SIM, it can dial out and send/receive sms but cannot receive call, why ? Can I make any changes let it work ?
In addition, I don't have any problem with both of these two ROM when using it in Hongkong.

What Radio version are you using perhaps this may be the cause of your problem

i agree, maybe u should change ur radio version
try using 1.50xxxxxx

kennethc2k said:
I have try the ROM of AX3L and Mary and use it at China using China Mobile SIM, it can dial out and send/receive sms but cannot receive call, why ? Can I make any changes let it work ?
In addition, I don't have any problem with both of these two ROM when using it in Hongkong.
Click to expand...
Click to collapse
Did you try the "connection setup" program? It should be around here somewhere..
There is also Advanced configuration tools But at the moment the operator part only supports European networks. But maybe they can add some settings for you

Bad link
mccune said:
Did you try the "connection setup" program? It should be around here somewhere..
There is also Advanced configuration tools But at the moment the operator part only supports European networks. But maybe they can add some settings for you
Click to expand...
Click to collapse
The link for Advanced Config. is for the old v 0.9 not v1.0

radio version
I have try both 1.46.x and 1.50.x, it have same problem. May be I should try the configuration setup as upper reply say .
Thanks every body's reply !

Advanced Config. link
kennethc2k said:
I have try both 1.46.x and 1.50.x, it have same problem. May be I should try the configuration setup as upper reply say .
Thanks every body's reply !
Click to expand...
Click to collapse
http://forum.xda-developers.com/misc.php?do=showattachments&t=333360
version 1.0

Call Forwarding Setup

My Nokia 6.1 is rooted and installed with Havoc 3.8 ROM.This ROM is not equipped with Call Forwarding function.So anybody please suggest a way to get Call Forwarding function in this Nokia 6.1 phone with Havoc 3.8 ROM?