Related
During an attempt to flash a rom using odin to my rooted sgs2, odin crashed and closed before it was finished. I tried restarting odin, wouldnt see phone.
Removed battery from phone, reconnected to odin and tried using the one click odin to reflash back to stock. Also tried using odin with other roms to flash back.
Heres my problem.
When i power on the phone, it says the Galazy S2 i9100 for a few seconds, then just turns off.
I can open odin, or odin one click, plug in phone, shows me yellow w/com and added. I click start, it gets to Setupconnection and then just sits there.
I have tried
- Different roms and both one click and normal odin.
- Different usb cables
- Different usb ports
- Multiple computers
Is there any way to get past this? God i hope someone can either point me somewhere or help me out.
Reinstall Samsung Kies to your laptop or pc so the proper drivers are re-installed. Once complete with that install, plug your phone into the pc and put the phone into USB mode, hopefully the pc will recognize your phone and install the NEW DEVICE drivers after a few moments. Depending on your pc, sometimes it takes many seconds for your pc to recognize and bring up the drop down menu for the newly recognized drive. BE PATIENT. If the pc does recognize your phone, start Odin again. If Odin also see's your phone, which it now should, you should see a COM:# connection in the ID:COM box of Odin. Doesn't matter what COM # is, as long as something is there. You can now use Odin because it see's your phone. Once you start Odin flashing, make sure not to disconnect anything until you see the upper left GREEN PASS box in Odin. Once its GREEN with PASS in that box, you're finished. You can d/c your phone from the pc and the phone is probably rebooting anyway.
OFC, if your phone will not stay power'd up, all of the above is for nought. Wish I could be more helpful.
Keep in mind that I do not intend to insult intelligence but everyone has limits in experience and I always try to explain in the simplest way I can. No disrespect intended.
Good Luck!
R
Thanks for the reply,
How am i supposed to put the phone in usb mode when i cant boot it?
That does create a problem, I would do some research on a USB Jig for your phone. Search at eBay for: Samsung Galaxy S2 Epic 4G Touch USB Jig
I'm not sure if this will help a phone that will not power up but it does have its uses for Root'd phone especially using Odin to flash and to remover that nasty YELLOW Triangle that comes from ROOT ROMS that are unsign'd.
Wish I could help you further.
R
Scribes said:
Thanks for the reply,
How am i supposed to put the phone in usb mode when i cant boot it?
Click to expand...
Click to collapse
Try to put in download mode if not try a jig ... If that fails it's sprint or jtag
Sent from my SPH-D710 using xda premium
It does power on, basically shows the sgs boot logo (black backgroud w/ white text) then goes dark, but its actually still on cause it gets hot.
I can get it into download mode and i can get it into the android recovery.
Theres gotta be a way to recover with an update.zip from the android recovery via the sd card........
There you go, you have two of us saying about the same thing. Just make sure you get the correct JIG if you go that route. It's like $2.00 and arrives from China in like 2 weeks.
http://www.ebay.com/sch/i.html?_fro...e+for+Samsung+Galaxy+S2/i9100/i9000/T959/i897
---------- Post added at 09:41 AM ---------- Previous post was at 09:37 AM ----------
humm, an idling phone shouldn't get hot. That tells me you've got something going on. I think you just progress'd passed my pay grade my friend.
Heres another thing, as i mentioned in my first post.
The boot logo says i-9100....
and this is a sprint phone, isnt it a d710?
So im gussing in my late night haze i screwed myself by loading an i9100 rom/bootloader/whatever the hell that is.
Samsung calls it: I9100
Sprint calls it: SPH710
We call it: Epic 4G Touch
I see, so thats not the problem?
Im just gonna keep posting here while i mess with this incase i trigger someones mind for a fix.
(picture was here apparently i cannot post an external link yet. Was just a picture of device manager and odin sitting at SetupConnection)
The only way to get odin to see my phone, is if i open odin, put phone in download mode, plug phone in, then uninstall the com port via device manager, reinstall it. When i rescan for hardware changes, odin goes yellow as seen in the picture, i click start, then it sits at SetupConnection all day, so im guessing its losing the connection after it finds it.
My only solution here is via usb card i think, but i cant find a signed package. Cant someone just pull theirs from a stock phone? Why wouldnt that work?
Well, if you can get Odin to work, unroot to full stock with this:
http://www.megaupload.com/?d=ISD9AOP0
Right, getting odin to work is the real problem though i think.
Stuck at SetupConnection forever
This is super frustrating... going without a phone is impossible, work emails, texts, calls, ahhhh
..and there is no way to completely reload the entire phone using an update.zip off the sd card, one that is signed?
I know i used to do that on my droid, and all though i know this is a totally different game, i still have android recovery, one would think it would be possible if the package was signed. unsigned ones just fail, but at least i can attempt to run them from there.
If someone can find a way to do that, and it works for my phone, i will paypal $50
Let me see what I can find for ya....
I have searched two different Forums for a flashable unroot to stock with NO luck. Everything I found requires Odin. Sorry Buddy.
Correct me if I'm wrong but isn't the i-9100 a whole different phone??? Looking at the specs and release date I would believe so. Sounds like he did an ics update for a phone that wasn't the Sph-d710 or something..
http://www.gsmarena.com/samsung_i9100_galaxy_s_ii-3621.php
Sent from my SPH-D710 using XDA App
not sure, all I know it by is: SPH 710
~ via My Epic 4G Touch & XDA'a app ~
Have you tried just flashing a kernel only in Odin
Sent from my SPH-D710 using xda premium
You tried flashing ICS on your phone, didn't you? B/C I'm pretty sure that's why you are seeing I9100 while booting up. If that is the case, do a search here as there are multiple people who have done this, and none of them have been able to fix it.
Sorry, your only solution is exchange at Sprint if you can, or JTAG.
help
beezar said:
You tried flashing ICS on your phone, didn't you? B/C I'm pretty sure that's why you are seeing I9100 while booting up. If that is the case, do a search here as there are multiple people who have done this, and none of them have been able to fix it.
Sorry, your only solution is exchange at Sprint if you can, or JTAG.
Click to expand...
Click to collapse
does not mean he flashed ICS when you odin a kernel that is not signed ie with CWM you will get yellow triangle and it will say i9100 too ..... so does not mean he flashed ics ... if odin sees the phone on a com port he probably didnt .... try flashing a working kernel from our phone
I did attempt to flash ICS. I could find where i got it, but it was supposedly for the Epic 4G touch, aka sprint sgs2 variant.
I am a network and systems admin, i should have known better. I jumped the gun and got ahead of myself. I have rooted and put roms on the og droid, and the droid x, samsung is a different beast all together.
However, i went in to sprint the day after i did this, they looked at it, no insurance, no replacement warranty, they didnt ask me anything, and THEY determined it was a factory defect , they had me sign a sheet that said "After researching found phone to be a factory defect and the solution from SPRINT is to replace the phone. $37.41, and 22 hours later i had a brand new SGS2 in my hand.
They hadnt sent my phone in yet. I honestly am not sure if they are going to be able to tell if i did anything to it or not, i may have just hosed the bootloader enough that odin wont connect, so they probably will have to use something like jtag in house to reflash it, or replace the chip or whatever they do. Even so, if they do see that i was messing with it, and say it voided my warranty, i have a signed receipt showing my payment and agreeing to pay for the replacement at $37.41, and that THEY determined the flaw. My brother in law is a lawyer, so i asked him, because i was curious if they would look at my phone at the service center or hub or whatever, and determine it was my fault. He assured me they could try, but it would all fall back to the employee who had me sign the agreement, so even if they dont like what i did, they are beyond doing anything about it.
I doubt they will even notice it, im sure they will try to boot it, then just flash it or however they do it.
Either way, im not worried anymore.
So...someone wanna point my idiot ass to an actual good rom, with a good method, that works for my phone? lol. I cant stand touchwiz, huge icons and cant replace them ....wtf is that all about.
Guys I'm desperate,
Helping my friend with his new GS3, I got root easy and downloaded JellyBAM 5.1 without realizing the bootloop issues over there. Anyway, I took the advice in that forum and did a full wipe to get past the bootloop... didn't work. Thought I'd just restore a nandroid and it was on that was in there previously from some unknown source (he's since confirmed that it was a ROM from his old VZW thunderbolt).
Suffice to say now I cannot get into recovery, I ONLY have access to the downloading screen (down + middle + power). My attempts with ODIN and whatever other suggestions in the forums have been unsuccessful. The Toolkit is the closest I've come but the issue with that its constantly waiting for USB debugging. Anyway, at this point the USB connection to the phone doesn't show any files on my PC. I can't figure out a way to connect to it and push an img or any kind of fix. I'm hoping the community can help me with this one, I promise I'll read better next time around. Any thoughts/advice?
Well, first off... Let's hear why your Odin attempts have been unsuccessful first so we have a better idea of what you have done exactly.
Sent from my SPH-L710 using Tapatalk 2
Try http://forum.xda-developers.com/showthread.php?t=2017470 while you are in download mode.
I've done my fair share of searching and I couldn't come up with much so I strongly believe I have a unique problem. I hope someone can point me in the right direction
Im have a rooted GS3 747 running Paranoid Android. A couple days ago the phone wouldn't charge. I tried different cables and batteries and after some testing with other GS3's I realized that my phone's charging port was broken. As a result I couldn't even connect my phone to the computer to unroot it with odin. I want to unroot so I can send in the phone for repair under warranty. So I downloaded mobile odin pro and proceeded to unroot my phone. I copied the original rogers rom to the external sd, followed the instructions and started the process. Everything looked like it was going fine until I got stuck on the samsung screen. Did some more research and learned that I had to do a factory data restart by booting into recovery mode. Did that. By now I'm feeling pretty good about all this. I followed the instructions all the way and I'm thinking that I'm gonna get a stock phone shortly. Wrong! The phone was still stuck on the samsung screen.
Now since I cant connect my phone to the PC cuz the charging port is broken I dont know what to do. I would have just flashed Clockwork Mod like I did when I first rooted and started all over but I cant.
If no one has a solution then Im just thinking of sending it in as is. Maybe they wont be able to see that the phone is rooted since they wont be able to connect it their PC without swapping out the motherboard to fix the problem.
I should add that I went to a repair store to try and fix it and they told me that the only way would be swap out your mobo.
machdown said:
I've done my fair share of searching and I couldn't come up with much so I strongly believe I have a unique problem. I hope someone can point me in the right direction
Im have a rooted GS3 747 running Paranoid Android. A couple days ago the phone wouldn't charge. I tried different cables and batteries and after some testing with other GS3's I realized that my phone's charging port was broken. As a result I couldn't even connect my phone to the computer to unroot it with odin. I want to unroot so I can send in the phone for repair under warranty. So I downloaded mobile odin pro and proceeded to unroot my phone. I copied the original rogers rom to the external sd, followed the instructions and started the process. Everything looked like it was going fine until I got stuck on the samsung screen. Did some more research and learned that I had to do a factory data restart by booting into recovery mode. Did that. By now I'm feeling pretty good about all this. I followed the instructions all the way and I'm thinking that I'm gonna get a stock phone shortly. Wrong! The phone was still stuck on the samsung screen.
Now since I cant connect my phone to the PC cuz the charging port is broken I dont know what to do. I would have just flashed Clockwork Mod like I did when I first rooted and started all over but I cant.
If no one has a solution then Im just thinking of sending it in as is. Maybe they wont be able to see that the phone is rooted since they wont be able to connect it their PC without swapping out the motherboard to fix the problem.
I should add that I went to a repair store to try and fix it and they told me that the only way would be swap out your mobo.
Click to expand...
Click to collapse
You will want to be sure that your flash counter says 0. This can be found by entering download mode (vol down, home, power) and you will see "custom binary count". that is how they will tell that you have rooted. Have you entered recovery and done a factory reset to get past the boot screen? If you can full wipe/ factory reset and get back into Android, I recommend you use "triangle away" app to clear your flash counter.
BCSC said:
You will want to be sure that your flash counter says 0. This can be found by entering download mode (vol down, home, power) and you will see "custom binary count". that is how they will tell that you have rooted. Have you entered recovery and done a factory reset to get past the boot screen? If you can full wipe/ factory reset and get back into Android, I recommend you use "triangle away" app to clear your flash counter.
Click to expand...
Click to collapse
I entered download mode and dont see flash counter anywhere. I got the warning screen were you have the option to restart or download.
Ya I entered recovery and did a factory reset but nothing. Really cant do anything with charging port broken.
I sent it in anyways for repairs. Hopefully they just replace it
I'm having the same problem with my Gs3 with CM10 4.2.2 running. Thought this would help.
Sent from my SPH-L710 using xda app-developers app
SOooO I'm just some tinkering nut that likes to check out all of the roms out there for my devices. Flashing is worse than crack for me. I have bricked de-bricked and re-bricked this poor little galaxy and updated to 4.3 and downgraded back to 4.0 all to make it look like it just came out of the box again. nice clean bootloader. A factory rom. 0 flash count which is simply nutz since this thing should be a stripper I have flashed it with so many Roms and Mods. I have pretty much every file you can think of for this device on my computer and I am more than happy to share my information and tips with the community here at xda.
If you think you need some assistance and don't want to spend 3days hopped up on pizza and mt.dew searching every inch of the forums looking for answers feel free to ask me and I can try my best to help out.
I have almost every custom Rom out for this device.
I have Custom Kernels from chapters 4.0.3 - 4.1.1 - 4.3 - 4.4
I have Debrick Images from the first three chapters will make one for 4.4 when I see a stable Rom
I have Stock Rom Files
I have updated Stock Rom Files.
I have updated rooted no knox Files
I have a crap load of continuous hours of searching breaking and Fixing this poor little thing.
I would have made a Tutorial page but it looks like there are plenty on the forums. I KNOW I've read them all:silly:
so I would rather put my knowledge to use in letting you simply ask me a question and I will reply as quickly as possible.
I know its going to sound nubcake. Buuut.... this is my daily device and I know how frustrating it can be when you have made one of them fatal mistakes and your device goes black or won't flash your new custom rom you want to test out.
Shoot some questions my way and see if I can't help you out quicker than you searching the 4 corners of the net.
datbager said:
SOooO I'm just some tinkering nut that likes to check out all of the roms out there for my devices. Flashing is worse than crack for me. I have bricked de-bricked and re-bricked this poor little galaxy and updated to 4.3 and downgraded back to 4.0 all to make it look like it just came out of the box again. nice clean bootloader. A factory rom. 0 flash count which is simply nutz since this thing should be a stripper I have flashed it with so many Roms and Mods. I have pretty much every file you can think of for this device on my computer and I am more than happy to share my information and tips with the community here at xda.
If you think you need some assistance and don't want to spend 3days hopped up on pizza and mt.dew searching every inch of the forums looking for answers feel free to ask me and I can try my best to help out.
I have almost every custom Rom out for this device.
I have Custom Kernels from chapters 4.0.3 - 4.1.1 - 4.3 - 4.4
I have Debrick Images from the first three chapters will make one for 4.4 when I see a stable Rom
I have Stock Rom Files
I have updated Stock Rom Files.
I have updated rooted no knox Files
I have a crap load of continuous hours of searching breaking and Fixing this poor little thing.
I would have made a Tutorial page but it looks like there are plenty on the forums. I KNOW I've read them all:silly:
so I would rather put my knowledge to use in letting you simply ask me a question and I will reply as quickly as possible.
I know its going to sound nubcake. Buuut.... this is my daily device and I know how frustrating it can be when you have made one of them fatal mistakes and your device goes black or won't flash your new custom rom you want to test out.
Shoot some questions my way and see if I can't help you out quicker than you searching the 4 corners of the net.
Click to expand...
Click to collapse
What spetps I need to do to re flash previous bootloader?... im in 4.3
torreon901 said:
What spetps I need to do to re flash previous bootloader?... im in 4.3
Click to expand...
Click to collapse
I did not do any boot loader flashing. sorry wow first question and I already fail.
If I had to take a wild guess and you still have access to cwm or twrp flash the stock rom and you should be good.
torreon901 said:
What spetps I need to do to re flash previous bootloader?... im in 4.3
Click to expand...
Click to collapse
I take no responsibility if you mess up your phone but take a look here. http://forum.xda-developers.com/showthread.php?t=2083860 may be what your looking for.
torreon901 said:
What spetps I need to do to re flash previous bootloader?... im in 4.3
Click to expand...
Click to collapse
If you go from the 4.3 bootloader to a previous one, you will brick your device via an e-fuse. You shouldn't need to revert to an older bootloader anyway unless for a specific rom. If that is the case, you are better off waiting until the developer catches up.
datbager said:
I take no responsibility if you mess up your phone but take a look here. http://forum.xda-developers.com/showthread.php?t=2083860 may be what your looking for.
Click to expand...
Click to collapse
Also, please don't use anything off this page unless you have an international version of the S3. I am guessing you have the I747, DO NOT FLASH SOMETHING NOT MADE FOR YOUR PHONE! :highfive:
Here is where you need to start...http://forum.xda-developers.com/showthread.php?t=2321310
There is even a PSA in red letters about reverting from a 4.3 bootloader.
datbager said:
Shoot some questions my way and see if I can't help you out quicker than you searching the 4 corners of the net.
Click to expand...
Click to collapse
how do you create a debrick.img? My phone is in working condition but I just want to be prepared for down the road
Pretty sure I bricked it
I have an ATT Galaxy S3. I had OTA 4.3, and i just rooted it, installed TWRP, and made a backup. Then I wiped, and tried to install a custom rom, and failed. Could not restore back up, and after multiple times of trying to flash this odin : http://forum.xda-developers.com/showpost.php?p=46954804&postcount=119[/URL]. and failed attempts to even get Heimdall to even work, my Phone is now in this state when turned on:
ODIN MODE
PRODUCT NAME: SGH-I747
CUSTOM BINARY DOWNLOAD: Yes (3 counts)
CURRENT BINARY: Samsung Official
SYSTEM STATUS: Custom
QUALCOMM SECUREBOOT: ENABLE
Warranty Bit: 1
BOOTLOAD RP SWREV: 2
SWREV CHECK FAIL : Fused 2 > Binary 0
Any help would be grateful.
Edit. More info
I have found I can flash TWRP but I am unable to mount SDCard. it just doesn't do anything. same thing with CWR.
and KIES tries to run a firmware recovery and fails. looks like it trieds to installs 4.1
Still looking for help. Thanks.
thenowherekid said:
I have an ATT Galaxy S3. I had OTA 4.3, and i just rooted it, installed TWRP, and made a backup. Then I wiped, and tried to install a custom rom, and failed. Could not restore back up, and after multiple times of trying to flash this odin : http://forum.xda-developers.com/showpost.php?p=46954804&postcount=119[/URL]. and failed attempts to even get Heimdall to even work, my Phone is now in this state when turned on:
ODIN MODE
PRODUCT NAME: SGH-I747
CUSTOM BINARY DOWNLOAD: Yes (3 counts)
CURRENT BINARY: Samsung Official
SYSTEM STATUS: Custom
QUALCOMM SECUREBOOT: ENABLE
Warranty Bit: 1
BOOTLOAD RP SWREV: 2
SWREV CHECK FAIL : Fused 2 > Binary 0
Any help would be grateful.
Edit. More info
I have found I can flash TWRP but I am unable to mount SDCard. it just doesn't do anything. same thing with CWR.
and KIES tries to run a firmware recovery and fails. looks like it trieds to installs 4.1
Still looking for help. Thanks.
Click to expand...
Click to collapse
So i was able to get a micro SD card and download the files from here http://forum.xda-developers.com/showthread.php?t=2498233
Used TWRP to install the bootloader/modem, then the rom, then the kernel. After it installed successfully I rebooted the phone. Nothing comes up. It doesn't respond to power button, or download or recovery button sequence. When i plug it into my computer, device manager recognizes it as a port. Qualcomm HS-USB QDLoader 9008 (COM13)
thenowherekid said:
So i was able to get a micro SD card and download the files from here http://forum.xda-developers.com/showthread.php?t=2498233
Used TWRP to install the bootloader/modem, then the rom, then the kernel. After it installed successfully I rebooted the phone. Nothing comes up. It doesn't respond to power button, or download or recovery button sequence. When i plug it into my computer, device manager recognizes it as a port. Qualcomm HS-USB QDLoader 9008 (COM13)
Click to expand...
Click to collapse
sorry I didn't ever encounter that in my adventures with the device. I have quickly discovered that there are too many issues with them and the flashing. I have had more problems and bricked states than I care to look at. I got the phone operating and gummy installed on it and left it at that.
datbager said:
sorry I didn't ever encounter that in my adventures with the device. I have quickly discovered that there are too many issues with them and the flashing. I have had more problems and bricked states than I care to look at. I got the phone operating and gummy installed on it and left it at that.
Click to expand...
Click to collapse
Thanks.
Sudden Death AT&T GS3
Hi,
I have an AT&T Samsung Galaxy S3. I was running CM11 nightlies. It was working perfectly fine for all these days. Couple of days back it suddenly died. The phone hasn’t been switching on back since then. I tried putting it on full charge. Whenever I pull out the battery and reinsert it, it vibrates, The LED comes on and the Samsung screen comes on for a second and turn turns off again. I cannot access the recovery or download modes through the key combinations. I also tried going into download mode using a Jig. I have to remove the battery and reinsert it. The Jig did work and the phone did go into download mode but, only for a second and then turns off. I’m not sure what exactly the issue is.
I would be very grateful if you could help me find a solution.
Thanks.
thenowherekid said:
Thanks.
Click to expand...
Click to collapse
ok this is not for your device but it is a guide and you can look up a kid that has a video on youtube. scroll down to device firmwares and select your model. but this is the link to help you. http://forum.xda-developers.com/showthread.php?t=2369125
your help
IcemanReturns said:
Hi,
I have an AT&T Samsung Galaxy S3. I was running CM11 nightlies. It was working perfectly fine for all these days. Couple of days back it suddenly died. The phone hasn’t been switching on back since then. I tried putting it on full charge. Whenever I pull out the battery and reinsert it, it vibrates, The LED comes on and the Samsung screen comes on for a second and turn turns off again. I cannot access the recovery or download modes through the key combinations. I also tried going into download mode using a Jig. I have to remove the battery and reinsert it. The Jig did work and the phone did go into download mode but, only for a second and then turns off. I’m not sure what exactly the issue is.
I would be very grateful if you could help me find a solution.
Thanks.
Click to expand...
Click to collapse
once again not for your device but scroll down to stock firmwares and READ the whole guide. There is a kid that makes a video some where arround here as well. http://forum.xda-developers.com/showthread.php?t=2369125 you need a 16gb class 10 sdcard or larger as well for this
Disk Space Back
I had trouble getting my max disk space after I did the debrick trick. So i'm going to shoot a quick tip to get all your space back.
go to your windows start menu and in the search type diskpart and hit enter.
in the command line type "list disk" no quotations and enter.
You should see your hard drive and any other storage devices connected in you computer. Determine which one is the sd card.
Next in the command line hit select disk x. x represents your sdcard.
last is clean disk in command line and your sd card has all its space but you must reformat it how ever you choose.
I just used sd formater.
hope that helps some peeps if so hook a noob up with some thanks clicks. :good:
Hi I have 4.1.1 rooted and twrp and I want to flash the collective rom which is 4.4. I have notbflashed this phone yet but I have done ot before on my captivate. What should I look out for and are there any stepsb I need to take before I flash, I.e. update bootloader etc and if so which one do i use
Sent from my SAMSUNG-SGH-I747 using xda app-developers app
hmm
trug2002 said:
Hi I have 4.1.1 rooted and twrp and I want to flash the collective rom which is 4.4. I have notbflashed this phone yet but I have done ot before on my captivate. What should I look out for and are there any stepsb I need to take before I flash, I.e. update bootloader etc and if so which one do i use
Sent from my SAMSUNG-SGH-I747 using xda app-developers app
Click to expand...
Click to collapse
I ended up doing the upgraded bootloader stuff and flashed
Android 4.3 I747UCUEMJ2 for AT&T Galaxy S3 I747
wich you can find here of course I take no credit just showing you where to look.http://wccftech.com/update-att-galaxy-s3-i747-leaked-ucuemj2-android-43-jelly-bean-firmware/
if I help hook a noob up with a thanks click its just a click. :laugh:
datbager said:
I ended up doing the upgraded bootloader stuff and flashed
Android 4.3 I747UCUEMJ2 for AT&T Galaxy S3 I747
wich you can find here of course I take no credit just showing you where to look.http://wccftech.com/update-att-galaxy-s3-i747-leaked-ucuemj2-android-43-jelly-bean-firmware/
if I help hook a noob up with a thanks click its just a click. :laugh:
Click to expand...
Click to collapse
Can you help me with this? I copied my thread :3
LiLTrippz said:
*I bought this off a friend of mine.*
All he told me was that he tried installing a rom and he thinks that he installed a rom for a different model S3.
What Happens/What I Did?
1. I tried to plug it into the computer and the computer doesn't show that anything plugged in, the S3 doesn't turn on. NOTHING.
2. I connected the phone to the PC without the battery inside and the phone responds with one RED light at the top left of the phone. Nothing shows up on my computer still, not even that the phone was connected NOTHING.
3. I bought a JIG device and tried plugging it into my phone and it doesn't work. (I previously tested this JIG on another samsung device and it worked)
4. I tried doing the method to use a 16gb SD card and downloading an i747m debrick IMG and using Win32FlashTool to copy it to my SD Card. I tried with 2 different cards the first one was a 16gb SD card and the other was a 32gb SD card.
5. Through a lot of research I found a leaked way to unbrick the Samsung Galaxy S3 i9300 by shorting out the R313 chip, I'm sure you guys are all aware of this method. I opened my device and couldn't find the R313 chip. After further research I found that a user was able to locate the R313 chip on the i747m and he'd unbricked his phone with that method. If anyone can help me locate the i747m R313 chip it'd be GREATLY appreciated!
If anyone can help me out it would be great! I'm very experienced at soldering so if there's a method that requires me to solder I'm more than confident I can do it.
Thank you!! :good:
Click to expand...
Click to collapse
i have the dlk3 boot loader do I need to go to mjb?
Sent from my SAMSUNG-SGH-I747 using xda app-developers app
trug2002 said:
i have the dlk3 boot loader do I need to go to mjb?
Sent from my SAMSUNG-SGH-I747 using xda app-developers app
Click to expand...
Click to collapse
I am not an expert but I'm pretty sure you need the mjb2 but there are guides all over that point misleading information. I can post a link that I believe is helpful. And as always I take no credit just pointing a finger here.
http://www.usofttech.com/t51443.html
:good:
PLEASE READ EVERYTHING FOR BETTER UNDERSTANDING
Hey fellow LG Owner(s) I am writing this asking for some help. I know that majority of LG Phones use the same software and flashing tools regarding taking your phone back to stock. I currently own an LG G Flex (LS995 Sprint Variant) and I managed to soft brick my phone. I have posted this same message over at the LG G Flex Threads but so far I have gotten no one to provide me some sort of solution on how to un-brick or factory reset my phone.
The status of my phone before it got bricked was it had Root (IOROOT method), Busy-Box (by Jrummy), Build.Prop was edited to display as a Nexus 5, and boot-loader locked along with no custom recovery. If you’re wondering why my boot-loader was locked and why there wasn’t any type of custom recovery was due to the sad fact that Developers are having a hard time on cracking it.
Now to explain on how I soft bricked my phone. I was changing my font style by using a tool called ROM Toolbox (by Jrummy). I managed to change my font once and I attempted to change it a second time, since I was looking for something that displayed it wider and bolder. So as I applied install on the new font I got an automatic reboot.
The reboot consisted of the normal LG Logo display, followed by a black screen and staying as a black screen. On the upper left of my phone the notification indicator was flashing multiple colors (red, white, blue etc). This is the current state of my phone, black screen with a multicolor notification.
My attempts to fix:
- Simple reboot of the phone ((fail))
- Let the phones battery drain out then charge for a few minutes and restart ((fail))
- Managed to get into STOCK recovery and perform clean partition ((fail)
- Managed to get into STOCK recovery and apply factory reset ((fail))
- I got into some weird mode which also gave me the option to apply factory reset ((fail))
- I followed this tutorial (LG Flash Tool) on how to revert back to stock (by hyelton) ((fail))
Link to tutorial: http://forum.xda-developers.com/showthread.php?t=2644083
The tutorial by hyelton was almost successful to reverting back to stock firmware until I got to the last step (Number 6). The error that occurred by using the LG Flash Tool was when the tool attempted to flash the stock firmware it gave me a Download FAIL!! “Device Model is different“ notification (Images below). I did this tutorial at least seven times and I got no luck. Every single time that I attempted to do this I kept getting the same notification. I have now ran out if ideas on what to do.
My theory, I believe that by changing my build prop to display as a nexus 5 is the reason why I keep getting this fail notification. On the phone it-self when I put it into download mode it even displays as a Nexus 5 (Images below).
I was wondering since it’s possible to get into STOCK RECOVERY, I saw that it had an option for “ADB SIDELOAD” is it possible to push something thru ADB??? Any type of help is greatly appreciated and thanked. Please do not get upset that you see this in multiple LG threads, I am just trying to find a solution to UNBRICK this very expensive phone that I bought and I cannot afford to just use it as a paper weight. THANK YOU AND GOD BLESS
Here is a Link to all my files regarding STOCK tot,dll,lg flash tools,aboot, buildprop, lg usb drivers and adb drivers that are for my phone
Link: https://drive.google.com/folderview?id=0B1D8UNLjuTB6TWpCQ1pJME5qWk0&usp=sharing
i hope these files help anyone that are attempting to help me put my phone back to stock
Alright yall, I am almost official screwed. I purchased this phone about a month ago from Best Buy and they stated that I am out of there 15 day window so I cannot exchange or replace for the same phone. I then went to Sprint on whom I have phone insurance for and they stated that they cannot do anything and that I have to go to one of their Sprint repair stores. I went to one of the repair stores and the gentlemen that assisted me plugged my phone to his computer and immediately knew that my phone was rooted. So from there I played the dumb blonde card acting like I don’t know what he’s talking about and from there he directed me to call LG and see what they can do. So now the current status is I filed a repair request and now I am awaiting a reply from LG. Does anyone have any suggestion???
**SOLUTION** hey yall i got the solution to my problem and it was simply by downloading this universal custom .dll from
http://forum.xda-developers.com/show....php?t=2663369
and i managed to flash back to stock recovery using this guide. instead using the dll on the the guide i used the custom one.
*GUIDE BACK TO STOCK*
http://forum.xda-developers.com/show....php?t=2644083
bump
edit: sorry missed that, but if you have access to download mode, the flash tool should work i would think..try it again maybe and make sure you didnt miss anything.
i would try following this guide, make sure you use the g flex .tot and .dll though. copied from the lg g2 back to stock guide from hyelton
hyelton said:
RETURN TO STOCK TOT Method! AT&T & Sprint Verzion & The Few International TOTs I have available
Download
1. LGFlashTools v1.8 - Download
2. Drivers - Download
3. Download Both Stock Image File and DLL (Both Files) - Download
Credit to @madmack for making most of this Guide for the G Pro Which also works on our G2
3.1 - FOR SPRINT FIRMWARE - Click Here
3.2 FOR International KITKAT TOT`s Click Here
Install
1. Install the LG drivers downloaded above.
2. Install LGFlashTools v1.6 (but don't run it)
3. Extract the TOT file from the ZIP
Drivers initialization
1. Put the phone into download mode. (Turn off device PRESS VOL UP while plugging in the micro usb cable. If this doesn't work, try holding both volume keys instead)
2. Let the phone initialize and install the drivers. Once done, in Device manager, you should see the LG phone listed under COM ports (something along these lines).
3. Find that LG entry in Device Manager, click on Properties, Advanced and then change the COM port to COM41 and close/save.
4. Unplug your phone! Important step.
LGFlashTools
To get this tool to work, you'll need to do a few tricks.
1. Set the computer's date to some time in July 2012 or before.
2. Disconnect the internet
3. Find a serial number or register key from somewhere on the web (a google search for lgflashtools serial will yield some results). Can't help you here and please don't share any keys in this thread or get us in trouble.
4. Execute the LGFlashTools. It should ask you for a key, put it in. Now you should see a dialog where you can load the DLL file and the TOT files that you extracted earlier. Put them both in here. Click ok
Flashing
5. There is a yellow arrow on the top left. Click on it to initialize the process. Once done, it should say "ready/finished" or whatever.
6. Put the phone in download mode again, and plug it into the USB port. LG FLash Tools should start flashing it automatically. When it's done, it'll automatically reboot into your stock AT&T rom and all of your data and internal sdcard files are gone.
Click to expand...
Click to collapse
Does ADB come up on the normal boot? If so maybe you can remount system and force replace build.prop...
Sent from my LG-LS980 using Tapatalk
Link to All Stock Files, Tools and More
Here is a Link to all my files regarding STOCK tot,dll,lg flash tools,aboot, buildprop, lg usb drivers and adb drivers that are for my phone
Link: https://drive.google.com/folderview?id=0B1D8UNLjuTB6TWpCQ1pJME5qWk0&usp=sharing
i hope these files help anyone that are attempting to help me put my phone back to stock
jmacphee9 said:
edit: sorry missed that, but if you have access to download mode, the flash tool should work i would think..try it again maybe and make sure you didnt miss anything.
i would try following this guide, make sure you use the g flex .tot and .dll though. copied from the lg g2 back to stock guide from hyelton
Click to expand...
Click to collapse
i have followed that guideline but when i go into download mode the phone displays as a nexus 5 instead of lg g flex and from there the lg flash tool fails to flash anything because it displays different model. remember my build prop was edited to display as a nexus 5
garwynn said:
Does ADB come up on the normal boot? If so maybe you can remount system and force replace build.prop...
Sent from my LG-LS980 using Tapatalk
Click to expand...
Click to collapse
adb sideload comes up as an option on stock recovery. can you please show me the command to push that. also do i have to pull the old build prop and then push the original one???
just a quick thought here, I had kind of the same problem on my G2 LS980 ( it thought it was a model 801) and to get around the error I used the correct .dll for my model phone but renamed it to the reported models .dll name, this should get the LG Tool past that check .dll error,
so for your case, you will need to find the Nexus .dll to get the name of it, then you will make a copy of your LG Flex .dll and rename that copy to the name of the nexus .dll, then when you manually load the .dll into LG Flash Tool use the renamed .dll, hope this helps you out, best of luck!
Alright yall, I am almost official screwed. I purchased this phone about a month ago from Best Buy and they stated that I am out of there 15 day window so I cannot exchange or replace for the same phone. I then went to Sprint on whom I have phone insurance for and they stated that they cannot do anything and that I have to go to one of their Sprint repair stores. I went to one of the repair stores and the gentlemen that assisted me plugged my phone to his computer and immediately knew that my phone was rooted. So from there I played the dumb blonde card acting like I don’t know what he’s talking about and from there he directed me to call LG and see what they can do. So now the current status is I filed a repair request and now I am awaiting a reply from LG. Does anyone have any suggestion???
best of luck to you!
Hey christiam.coronado any luck on fixing this yet? I have the same problem as you do. Someone edited the build.prob before selling me the phone and when i went to factory reset it without knowing it was rooted and build.prob was messed with now my lg g flex ls995 thinks its a d959at whatever that may be
SOLUTION
**SOLUTION** hey yall i got the solution to my problem and it was simply by downloading this universal custom .dll from
http://forum.xda-developers.com/show....php?t=2663369
and i managed to flash back to stock recovery using this guide. instead using the dll on the the guide i used the custom one.
*GUIDE BACK TO STOCK*
http://forum.xda-developers.com/show....php?t=2644083
christiam.coronado said:
**SOLUTION** hey yall i got the solution to my problem and it was simply by downloading this universal custom .dll from
http://forum.xda-developers.com/show....php?t=2663369
and i managed to flash back to stock recovery using this guide. instead using the dll on the the guide i used the custom one.
*GUIDE BACK TO STOCK*
http://forum.xda-developers.com/show....php?t=2644083
Click to expand...
Click to collapse
I have the same problem, but none of the download links work. Anyone have the files that christiam.coronado linked?
bad build.prop
can i use zv5 tot if im on zv6? i cant find a vz6 tot anywhere. can someone upload it please. im frustrated i messed up my phone for messing with the build.prop tryimg to unlock it. sigh...
hmm
garwynn said:
Does ADB come up on the normal boot? If so maybe you can remount system and force replace build.prop...
Sent from my LG-LS980 using Tapatalk
Click to expand...
Click to collapse
how would i do that on my sprint g flex 2?
christiam.coronado said:
PLEASE READ EVERYTHING FOR BETTER UNDERSTANDING
Hey fellow LG Owner(s) I am writing this asking for some help. I know that majority of LG Phones use the same software and flashing tools regarding taking your phone back to stock. I currently own an LG G Flex (LS995 Sprint Variant) and I managed to soft brick my phone. I have posted this same message over at the LG G Flex Threads but so far I have gotten no one to provide me some sort of solution on how to un-brick or factory reset my phone.
The status of my phone before it got bricked was it had Root (IOROOT method), Busy-Box (by Jrummy), Build.Prop was edited to display as a Nexus 5, and boot-loader locked along with no custom recovery. If you’re wondering why my boot-loader was locked and why there wasn’t any type of custom recovery was due to the sad fact that Developers are having a hard time on cracking it.
Now to explain on how I soft bricked my phone. I was changing my font style by using a tool called ROM Toolbox (by Jrummy). I managed to change my font once and I attempted to change it a second time, since I was looking for something that displayed it wider and bolder. So as I applied install on the new font I got an automatic reboot.
The reboot consisted of the normal LG Logo display, followed by a black screen and staying as a black screen. On the upper left of my phone the notification indicator was flashing multiple colors (red, white, blue etc). This is the current state of my phone, black screen with a multicolor notification.
My attempts to fix:
-Simple reboot of the phone ((fail))
-Let the phones battery drain out then charge for a few minutes and restart ((fail))
-Managed to get into STOCK recovery and perform clean partition ((fail)
-Managed to get into STOCK recovery and apply factory reset ((fail))
-I got into some weird mode which also gave me the option to apply factory reset ((fail))
-I followed this tutorial (LG Flash Tool) on how to revert back to stock (by hyelton) ((fail))
Link to tutorial: http://forum.xda-developers.com/showthread.php?t=2644083
The tutorial by hyelton was almost successful to reverting back to stock firmware until I got to the last step (Number 6). The error that occurred by using the LG Flash Tool was when the tool attempted to flash the stock firmware it gave me a Download FAIL!! “Device Model is different“ notification (Images below). I did this tutorial at least seven times and I got no luck. Every single time that I attempted to do this I kept getting the same notification. I have now ran out if ideas on what to do.
My theory, I believe that by changing my build prop to display as a nexus 5 is the reason why I keep getting this fail notification. On the phone it-self when I put it into download mode it even displays as a Nexus 5 (Images below).
I was wondering since it’s possible to get into STOCK RECOVERY, I saw that it had an option for “ADB SIDELOAD” is it possible to push something thru ADB??? Any type of help is greatly appreciated and thanked. Please do not get upset that you see this in multiple LG threads, I am just trying to find a solution to UNBRICK this very expensive phone that I bought and I cannot afford to just use it as a paper weight. THANK YOU AND GOD BLESS
Here is a Link to all my files regarding STOCK tot,dll,lg flash tools,aboot, buildprop, lg usb drivers and adb drivers that are for my phone
Link: https://drive.google.com/folderview?id=0B1D8UNLjuTB6TWpCQ1pJME5qWk0&usp=sharing
i hope these files help anyone that are attempting to help me put my phone back to stock
Alright yall, I am almost official screwed. I purchased this phone about a month ago from Best Buy and they stated that I am out of there 15 day window so I cannot exchange or replace for the same phone. I then went to Sprint on whom I have phone insurance for and they stated that they cannot do anything and that I have to go to one of their Sprint repair stores. I went to one of the repair stores and the gentlemen that assisted me plugged my phone to his computer and immediately knew that my phone was rooted. So from there I played the dumb blonde card acting like I don’t know what he’s talking about and from there he directed me to call LG and see what they can do. So now the current status is I filed a repair request and now I am awaiting a reply from LG. Does anyone have any suggestion???
**SOLUTION** hey yall i got the solution to my problem and it was simply by downloading this universal custom .dll from
http://forum.xda-developers.com/show....php?t=2663369
and i managed to flash back to stock recovery using this guide. instead using the dll on the the guide i used the custom one.
*GUIDE BACK TO STOCK*
http://forum.xda-developers.com/show....php?t=2644083
Click to expand...
Click to collapse
Help lg flash tool not working
Sent from my R1 HD using Tapatalk