During an attempt to flash a rom using odin to my rooted sgs2, odin crashed and closed before it was finished. I tried restarting odin, wouldnt see phone.
Removed battery from phone, reconnected to odin and tried using the one click odin to reflash back to stock. Also tried using odin with other roms to flash back.
Heres my problem.
When i power on the phone, it says the Galazy S2 i9100 for a few seconds, then just turns off.
I can open odin, or odin one click, plug in phone, shows me yellow w/com and added. I click start, it gets to Setupconnection and then just sits there.
I have tried
- Different roms and both one click and normal odin.
- Different usb cables
- Different usb ports
- Multiple computers
Is there any way to get past this? God i hope someone can either point me somewhere or help me out.
Reinstall Samsung Kies to your laptop or pc so the proper drivers are re-installed. Once complete with that install, plug your phone into the pc and put the phone into USB mode, hopefully the pc will recognize your phone and install the NEW DEVICE drivers after a few moments. Depending on your pc, sometimes it takes many seconds for your pc to recognize and bring up the drop down menu for the newly recognized drive. BE PATIENT. If the pc does recognize your phone, start Odin again. If Odin also see's your phone, which it now should, you should see a COM:# connection in the ID:COM box of Odin. Doesn't matter what COM # is, as long as something is there. You can now use Odin because it see's your phone. Once you start Odin flashing, make sure not to disconnect anything until you see the upper left GREEN PASS box in Odin. Once its GREEN with PASS in that box, you're finished. You can d/c your phone from the pc and the phone is probably rebooting anyway.
OFC, if your phone will not stay power'd up, all of the above is for nought. Wish I could be more helpful.
Keep in mind that I do not intend to insult intelligence but everyone has limits in experience and I always try to explain in the simplest way I can. No disrespect intended.
Good Luck!
R
Thanks for the reply,
How am i supposed to put the phone in usb mode when i cant boot it?
That does create a problem, I would do some research on a USB Jig for your phone. Search at eBay for: Samsung Galaxy S2 Epic 4G Touch USB Jig
I'm not sure if this will help a phone that will not power up but it does have its uses for Root'd phone especially using Odin to flash and to remover that nasty YELLOW Triangle that comes from ROOT ROMS that are unsign'd.
Wish I could help you further.
R
Scribes said:
Thanks for the reply,
How am i supposed to put the phone in usb mode when i cant boot it?
Click to expand...
Click to collapse
Try to put in download mode if not try a jig ... If that fails it's sprint or jtag
Sent from my SPH-D710 using xda premium
It does power on, basically shows the sgs boot logo (black backgroud w/ white text) then goes dark, but its actually still on cause it gets hot.
I can get it into download mode and i can get it into the android recovery.
Theres gotta be a way to recover with an update.zip from the android recovery via the sd card........
There you go, you have two of us saying about the same thing. Just make sure you get the correct JIG if you go that route. It's like $2.00 and arrives from China in like 2 weeks.
http://www.ebay.com/sch/i.html?_fro...e+for+Samsung+Galaxy+S2/i9100/i9000/T959/i897
---------- Post added at 09:41 AM ---------- Previous post was at 09:37 AM ----------
humm, an idling phone shouldn't get hot. That tells me you've got something going on. I think you just progress'd passed my pay grade my friend.
Heres another thing, as i mentioned in my first post.
The boot logo says i-9100....
and this is a sprint phone, isnt it a d710?
So im gussing in my late night haze i screwed myself by loading an i9100 rom/bootloader/whatever the hell that is.
Samsung calls it: I9100
Sprint calls it: SPH710
We call it: Epic 4G Touch
I see, so thats not the problem?
Im just gonna keep posting here while i mess with this incase i trigger someones mind for a fix.
(picture was here apparently i cannot post an external link yet. Was just a picture of device manager and odin sitting at SetupConnection)
The only way to get odin to see my phone, is if i open odin, put phone in download mode, plug phone in, then uninstall the com port via device manager, reinstall it. When i rescan for hardware changes, odin goes yellow as seen in the picture, i click start, then it sits at SetupConnection all day, so im guessing its losing the connection after it finds it.
My only solution here is via usb card i think, but i cant find a signed package. Cant someone just pull theirs from a stock phone? Why wouldnt that work?
Well, if you can get Odin to work, unroot to full stock with this:
http://www.megaupload.com/?d=ISD9AOP0
Right, getting odin to work is the real problem though i think.
Stuck at SetupConnection forever
This is super frustrating... going without a phone is impossible, work emails, texts, calls, ahhhh
..and there is no way to completely reload the entire phone using an update.zip off the sd card, one that is signed?
I know i used to do that on my droid, and all though i know this is a totally different game, i still have android recovery, one would think it would be possible if the package was signed. unsigned ones just fail, but at least i can attempt to run them from there.
If someone can find a way to do that, and it works for my phone, i will paypal $50
Let me see what I can find for ya....
I have searched two different Forums for a flashable unroot to stock with NO luck. Everything I found requires Odin. Sorry Buddy.
Correct me if I'm wrong but isn't the i-9100 a whole different phone??? Looking at the specs and release date I would believe so. Sounds like he did an ics update for a phone that wasn't the Sph-d710 or something..
http://www.gsmarena.com/samsung_i9100_galaxy_s_ii-3621.php
Sent from my SPH-D710 using XDA App
not sure, all I know it by is: SPH 710
~ via My Epic 4G Touch & XDA'a app ~
Have you tried just flashing a kernel only in Odin
Sent from my SPH-D710 using xda premium
You tried flashing ICS on your phone, didn't you? B/C I'm pretty sure that's why you are seeing I9100 while booting up. If that is the case, do a search here as there are multiple people who have done this, and none of them have been able to fix it.
Sorry, your only solution is exchange at Sprint if you can, or JTAG.
help
beezar said:
You tried flashing ICS on your phone, didn't you? B/C I'm pretty sure that's why you are seeing I9100 while booting up. If that is the case, do a search here as there are multiple people who have done this, and none of them have been able to fix it.
Sorry, your only solution is exchange at Sprint if you can, or JTAG.
Click to expand...
Click to collapse
does not mean he flashed ICS when you odin a kernel that is not signed ie with CWM you will get yellow triangle and it will say i9100 too ..... so does not mean he flashed ics ... if odin sees the phone on a com port he probably didnt .... try flashing a working kernel from our phone
I did attempt to flash ICS. I could find where i got it, but it was supposedly for the Epic 4G touch, aka sprint sgs2 variant.
I am a network and systems admin, i should have known better. I jumped the gun and got ahead of myself. I have rooted and put roms on the og droid, and the droid x, samsung is a different beast all together.
However, i went in to sprint the day after i did this, they looked at it, no insurance, no replacement warranty, they didnt ask me anything, and THEY determined it was a factory defect , they had me sign a sheet that said "After researching found phone to be a factory defect and the solution from SPRINT is to replace the phone. $37.41, and 22 hours later i had a brand new SGS2 in my hand.
They hadnt sent my phone in yet. I honestly am not sure if they are going to be able to tell if i did anything to it or not, i may have just hosed the bootloader enough that odin wont connect, so they probably will have to use something like jtag in house to reflash it, or replace the chip or whatever they do. Even so, if they do see that i was messing with it, and say it voided my warranty, i have a signed receipt showing my payment and agreeing to pay for the replacement at $37.41, and that THEY determined the flaw. My brother in law is a lawyer, so i asked him, because i was curious if they would look at my phone at the service center or hub or whatever, and determine it was my fault. He assured me they could try, but it would all fall back to the employee who had me sign the agreement, so even if they dont like what i did, they are beyond doing anything about it.
I doubt they will even notice it, im sure they will try to boot it, then just flash it or however they do it.
Either way, im not worried anymore.
So...someone wanna point my idiot ass to an actual good rom, with a good method, that works for my phone? lol. I cant stand touchwiz, huge icons and cant replace them ....wtf is that all about.
Related
When I try to turn my phone on it shows the image of a cellphone a orange triangle with ! in it and a computer. What did I do? Please help!
No. you're not bricked. It just failed during an Odin flash.
Here's how to fix it.
http://forum.xda-developers.com/showthread.php?t=1052813
That was what I did originally to get to this point. It gets stuck at set pit file
Is there anyway to fix it with cwm?
Give it another try. This time don't use the pit file. Just the SPH-D700-EC05-8Gb-REL.tar file in the PDA section and make sure there's a check next to it. Also, under option, just have "auto reboot" checked. Leave "re-partition" and "reset time" blank.
Before you posted your last message, i tried doing it again I got further but than my screen turned red and hung for 15 minutes. I pulled the battery and now my phone wont turn on at all. I cant even get it to dl mode
Read the unbrick post in delv sec than watch the videos from qbking77 before you do anything else and you wont have any problems.
Then thank qbking77 for educating the epic community on proper install procedures
I was going off that post when all of this happened. Doesnt matter now anyway it wont even turn on now. Tomorrow I have to go to the sprint store and hope they wont be able to know I was trying to flash.
thegameksk said:
I was going off that post when all of this happened. Doesnt matter now anyway it wont even turn on now. Tomorrow I have to go to the sprint store and hope they wont be able to know I was trying to flash.
Click to expand...
Click to collapse
Try pulling out the SD card and battery, then put battery back in and boot into download mode without SD card.
Might take a few tries with removing the battery.
Ill try that. If that doesnt work do you think sprint wud be able to tell that odin didnt flash correctly/ Should I just call and say my phone was lost?
Also even if I plug it into the wall with battery in phone it doesnt show red light on that shows its charging.
thegameksk said:
Ill try that. If that doesnt work do you think sprint wud be able to tell that odin didnt flash correctly/ Should I just call and say my phone was lost?
Also even if I plug it into the wall with battery in phone it doesnt show red light on that shows its charging.
Click to expand...
Click to collapse
If it's a true brick, even sprint techs won't be able to get it to power on/boot, in which case, they won't know what's on it. If it's still under the 1 year manufacture's warranty, in most cases, it normally cost $35 for a replacement or free if you're lucky, YMMV tho.
Hope things work out for ya, I've felt your pain before my friend.
Dont give up sometimes just sitting for a couple hours with no battery helps.
I got this while trying to odin the new EF## or whatever...
I tried to reset it and it didnt work, i tried odin'ing the EC05 tar and pit and it didnt work, it stuck...
Then i got the EB13 tar and pit and odin'd and it worked
Try checking repartition in odin, could have possibly been checked during the bad odin session and doing it again should clear it up. Use the stock ef02 tar not the pre rooted one
Sent from my SPH-D700 using XDA Premium App
I've followed about 10 different links to files that I'm attempting to download to de-soft brick my phone. I'm having ZERO luck. Everything is dead. I've never experienced anything like this before for the 10 or so Android phones I've owned and hacked.
I managed to find Odin 4.3, but I keep getting an invalid file error. & before you call me a noob and tell me to download it again, or change the file name. I've already done that. Several times.
Am I ****ed?
I don't know what Odin 4.3 is but...
If you can get into download mode, use Odin 1.85 and find a rom to try.
http://forum.xda-developers.com/showthread.php?t=1184091
If you can't get into download mode, then I'm not sure what to do as I haven't researched brick stuff.
I'm also not sure if the dev forum is the right place for this thread.
Maybe.. if u tried almost ever thing u could to bring your phone back from a brick and its still brick than maybe its time to give up.. pay your deductible and get yourself a replacement.. U have to remember there are consequences to hacking your phone and u have to deal with it now.. Sorry
Aryantes said:
I don't know what Odin 4.3 is but...
If you can get into download mode, use Odin 1.85 and find a rom to try.
http://forum.xda-developers.com/showthread.php?t=1184091
If you can't get into download mode, then I'm not sure what to do as I haven't researched brick stuff.
I'm also not sure if the dev forum is the right place for this thread.
Click to expand...
Click to collapse
true if u cant at least get into download mode than u SOL... i recovered from a brick phone the other day by holding down the four gold circle pins on the back of the phone and than trying to go into download mode.. it worked for me but others have tried it and said that it didnt work..
Natty_lite said:
I've followed about 10 different links to files that I'm attempting to download to de-soft brick my phone. I'm having ZERO luck. Everything is dead. I've never experienced anything like this before for the 10 or so Android phones I've owned and hacked.
I managed to find Odin 4.3, but I keep getting an invalid file error. & before you call me a noob and tell me to download it again, or change the file name. I've already done that. Several times.
Am I ****ed?
Click to expand...
Click to collapse
Try the thread that is titled, bring your phone back from the brink, or something like that.. as long as you have download mode, you are good to go. And odin 4.3 is not an app for our phone.. odin3 ver 1.86 i believe is the newest...
Natty_lite said:
I've followed about 10 different links to files that I'm attempting to download to de-soft brick my phone. I'm having ZERO luck. Everything is dead. I've never experienced anything like this before for the 10 or so Android phones I've owned and hacked.
I managed to find Odin 4.3, but I keep getting an invalid file error. & before you call me a noob and tell me to download it again, or change the file name. I've already done that. Several times.
Am I ****ed?
Click to expand...
Click to collapse
http://forum.xda-developers.com/showthread.php?t=1052813
Odin 1.65 is in this thread along with stock Froyo. I had a problem with my samsung logo not showing on boot and following the instructions in this thread got rid of my problem. As others have said, if you can't get into download mode you are out of luck as far as I know.
If you can't get into download mode and have TEP, take your phone into a Corporate Owned Repair Center, give them some bull**** story where suddenly your phone wouldn't come back on, I have done this twice now and they have given me a brand new Epic every time right there on the spot.....no deductible!
U sure down look round for a person that previously have 10 different android phones smh
Sent from my SPH-D700 using Tapatalk
If you can get into download mode but, you still can't flash, then you probably have a bad cable. If you are using the stock usb cable, replace it with a quality micro usb cable and that should get you sorted. The ones that come with the phone are garbage.
I do find it a little humorous when you say not to call you a noob immediately after you pull "Odin 4.3" out of your hat. You would do well if there was a techie stand up act and your timing was just right.
EDIT: post deleted, thread moved
theduce102 said:
So we can post "question" threads in the development section now? i believe ill go make a few
Click to expand...
Click to collapse
+1
Yeah man you sure are acting like a noob with the posting in development and all... not to mention odin 4... try turning everything off. Then hold 1 for like 15 seconds then press power while still holding 1. Try around with different combinations of that and it should turn on eventually. Mine did.
cd's or tapes?
Edit: too much natural light perhaps?
Tw I am a n00b and even I know that there is NO an odin 4.watever!
Sent From The Evo 3D's PIMP!
I was having trouble ODIN'ing my phone. It kept failing and I thought I bricked my phone because it wouldn't power on. I switched my USB port on my laptop and bam, it worked. Maybe try that (assuming you can get into download mode on your phone).
Try using another fully charged battery from a friends epic. Sometimes waiting an hour works can't tell you how many times I thought I hosed my epic or vibrant for that matter.
Sent from my SPH-D700 using XDA App
Odin Multi Downloader 4.03 wasn't the right tool for the job. I got it from a thread similar to mine where someone was bootlooping and needed to flash back to stock. However, the link provided in the thread that Aryander posted did the trick right away.
Thanx
Sorry for posting within the wrong section.
Before I begin, this is my first post here. I've used XDA before for help and love you guys. Now I need you more than ever. Thanks in advance for the help!
At first, my phone started to act all weird. By that I mean the Espier launcher wouldn't even load. It kept crashing. So I decided to unroot my phone. I used Odin to attempt to put the factory firmware and stuff on my phone but ended up prematurely ending the install, thus bricking my phone. When I turn my phone on I see the "Firmware upgrade encountered an issue" screen. So I did some research and attempted to fix the problem myself. After downloading and installing Kies (on three computers) I attempted to connect my phone to Kies. The USB port works, but none of my computers sees my phone. I've tried different USB ports, reinstalling Kies, using the connection debugging tool within Kies, changed the USB cable, taking the battery out, everything. If I am able to connect my phone to my computer I'll be able to fix the problem. If anyone could help me, that'd be lovely.
Can you get to download mode?
Sent from my SAMSUNG-SGH-T989 using xda premium
The only USB cable I've been able to use Odin or Kies with is the original cable that came with the phone. I have a ton of other micro USB cables, they all will charge but nothing else will do any sort of data transfer. Even then, I sometimes have to change USB ports and have encountered two PCs with won't recognize the phone no matter what. Keep trying.
It's odd, because my old HTC Hero was happy to connect and charge with any cable that fit.
rdsnyder said:
The only USB cable I've been able to use Odin or Kies with is the original cable that came with the phone. I have a ton of other micro USB cables, they all will charge but nothing else will do any sort of data transfer. Even then, I sometimes have to change USB ports and have encountered two PCs with won't recognize the phone no matter what. Keep trying.
It's odd, because my old HTC Hero was happy to connect and charge with any cable that fit.
Click to expand...
Click to collapse
Maxed22a said:
Can you get to download mode?
Sent from my SAMSUNG-SGH-T989 using xda premium
Click to expand...
Click to collapse
Yeah, I'm able to get into download mode. And I've also used the original cable that has provided with the phone.
Id try to odin the stock rooted kernel with what you have. I assume you still have a copy of what you rooted with... if not
http://forum.xda-developers.com/showthread.php?t=1433101
There you go.
Sent from my SPH-D710 using XDA
drinxtir said:
Id try to odin the stock rooted kernel with what you have. I assume you still have a copy of what you rooted with... if not
http://forum.xda-developers.com/showthread.php?t=1433101
There you go.
Sent from my SPH-D710 using XDA
Click to expand...
Click to collapse
The problem is none of my computers will detect my phone when I plug in the USB. I can't do anything else unless I can plug in my phone. I've tried installing the drivers, everything. Nothing works.
Ayotom said:
The problem is none of my computers will detect my phone when I plug in the USB. I can't do anything else unless I can plug in my phone. I've tried installing the drivers, everything. Nothing works.
Click to expand...
Click to collapse
Try a brand new high quality USB cable. Once in download mode try the new cable and Odin back to stock - sfhubs one-clicks are the life saver here.
Also. Have you tried 'stock' recovery/factory reset? This may get you to a good place. Then you can install a good stock ROM with root and recovery (again check out sfhub's posts)
Factory reset via stock recovery:
Hold down the Volume Up and Power buttons simultaneously.
Continue holding the Volume Up and Power buttons until the Samsung Galaxy S II logo screen is displayed.
When the Galaxy S II logo screen is displayed, release the Power button but continue holding the Volume Up button until the Android System Recovery menu is displayed.
Once you are on the Android System Recovery menu, select the wipe data/factory reset option. Moving the selection up and down is done with the Volume Up and Volume Down buttons. Once you have the wipe data/factory reset option highlighted, you select it by touching the Home button.
Once you have chosen the factory reset option, you will see a confirmation screen. Highlight the Yes — delete all user data option and touch the Home button to select it.
The procees of wiping the phone should only take a few seconds and when it is finished, you will be returned to the Android System Recovery menu.
Highlight and select the reboot system now option.
I sound like a broken record on the USB cable thing in many of my posts but that has been a cause for so much frustration for me and countless others. And the stock cable from Sammy sucks ass too.
Good luck.
leaderbuilder said:
Try a brand new high quality USB cable. Once in download mode try the new cable and Odin back to stock - sfhubs one-clicks are the life saver here.
Also. Have you tried 'stock' recovery/factory reset? This may get you to a good place. Then you can install a good stock ROM with root and recovery (again check out sfhub's posts)
Factory reset via stock recovery:
Hold down the Volume Up and Power buttons simultaneously.
Continue holding the Volume Up and Power buttons until the Samsung Galaxy S II logo screen is displayed.
When the Galaxy S II logo screen is displayed, release the Power button but continue holding the Volume Up button until the Android System Recovery menu is displayed.
Once you are on the Android System Recovery menu, select the wipe data/factory reset option. Moving the selection up and down is done with the Volume Up and Volume Down buttons. Once you have the wipe data/factory reset option highlighted, you select it by touching the Home button.
Once you have chosen the factory reset option, you will see a confirmation screen. Highlight the Yes — delete all user data option and touch the Home button to select it.
The procees of wiping the phone should only take a few seconds and when it is finished, you will be returned to the Android System Recovery menu.
Highlight and select the reboot system now option.
I sound like a broken record on the USB cable thing in many of my posts but that has been a cause for so much frustration for me and countless others. And the stock cable from Sammy sucks ass too.
Good luck.
Click to expand...
Click to collapse
All the help is appreciated, I just wanted to let you know that. If my tone is bitter, I apologize. I use this phone for emergencies. I have indeed tried a high quality USB cable (just bought it) and it will not connect. I attempted to use Odin to restore my phone back to normal but the process was interrupted and caused my phone to be in the phone....!....computer screen with the message "firmware upgrade has encountered a problem" etc. I have attempted to plug in my phone while Odin opened. Nada. I've tried this in download mode using the button commands you have listed. I hope I'm not getting too annoying, I just feel so lost without my phone. Had everything on it. Sorry.
Ayotom said:
All the help is appreciated, I just wanted to let you know that. If my tone is bitter, I apologize. I use this phone for emergencies. I have indeed tried a high quality USB cable (just bought it) and it will not connect. I attempted to use Odin to restore my phone back to normal but the process was interrupted and caused my phone to be in the phone....!....computer screen with the message "firmware upgrade has encountered a problem" etc. I have attempted to plug in my phone while Odin opened. Nada. I've tried this in download mode using the button commands you have listed. I hope I'm not getting too annoying, I just feel so lost without my phone. Had everything on it. Sorry.
Click to expand...
Click to collapse
Are you sure you were installing the right firmware? If you flashed an international verion then you did kill the device and will need to get it jtag'd or replaced.
And exactly how did it 'get interupted? Did it just 'stop' or was it interupted by a power outage, or impatience of quiting the appolication?
How did you get root? Did you use sfhub's autoroot?
And what ROM did you use? Again sfhub's Stock One-Clicks are the safest and only way to go in my book.
Not trying to be a **** just trying to get a better understanding of what happened.
leaderbuilder said:
Are you sure you were installing the right firmware? If you flashed an international verion then you did kill the device and will need to get it jtag'd or replaced.
And exactly how did it 'get interupted? Did it just 'stop' or was it interupted by a power outage, or impatience of quiting the appolication?
How did you get root? Did you use sfhub's autoroot?
And what ROM did you use? Again sfhub's Stock One-Clicks are the safest and only way to go in my book.
Not trying to be a **** just trying to get a better understanding of what happened.
Click to expand...
Click to collapse
I might have accidentally installed the wrong firmware while attempting to repair it. Unless the different SII model firmware wouldn't hurt my phone, such as the AT&T SII.
And battery laptop died.
I had my brother root it. It used Syndicate.
And no worries dude, I'm just glad you're helping!
I am not sure if anyone specifically tried the att gs2 firmware, but since att is gsm, chances are it is the same as flashing the intl gs2 firmware. Flashing the latter would basically disable your usb port. It does sound like that is what happened.
If you still had cwm or root you could flash from the phone, but i think you mentioned you lost those too.
Your remaining options are probably jtag or return to sprint.
Thank you very much for your help. It seriously means a lot. Next time I'll pay more attention so I won't end up screwing things up again.
Well if you tried to use the AT&T SG II (SGH-I777) firmware you did probably kill it for sure. These phones are very specific and individual when it comes to the actual hardware and base firmwares. Kind of like putting diesel into a gas engine - good things don't happen. If you can't get it recognized at all no matter what you do a jtag service or simply taking it back and playing dumb might help. Here is a post with almost the same issue, just a different but still wrong firmware: http://forum.xda-developers.com/showthread.php?t=1506630 As for the guys at ACS they are very good too (most of them are around here too by the way). Spend some time and read a whole lot and you will learn what you need. Best bet if you simply can't get it recognized by Odin is to take it back to Sprint and play dumb and see if they get you a replacement. With insurance you should get it free without I think you pay $35.
This might sound a little crazy... But have you tried heimdall to see if you get dirrerent results?
Update
So I decided to check out the JTAG service. Guess what I found out? The dude that repairs phones lives 20 minutes away from me! I went over to his place yesterday and he fixed my phone right in front of me. It was totally worth the $50! His service is amazing, and he's friendly also. I would highly recommend him! Read my review (I'm John Montoya): http://mobiletechvideos.mybigcommerce.com/samsung-epic-4g-touch-jtag-brick-repair/
Thanks everyone for the help. Next time I'll be sure not to put in the wrong firmware!
LOL that's pretty funny having the mobiletechvideos guy living in your town, and getting to watch the JTAG repair in person. Not many people can say they've seen that in person, myself included. Glad you got it resolved.
Sent from my SPH-D710 using Tapatalk 2
Ayotom said:
So I decided to check out the JTAG service. Guess what I found out? The dude that repairs phones lives 20 minutes away from me! I went over to his place yesterday and he fixed my phone right in front of me. It was totally worth the $50! His service is amazing, and he's friendly also. I would highly recommend him! Read my review (I'm John Montoya): http://mobiletechvideos.mybigcommerce.com/samsung-epic-4g-touch-jtag-brick-repair/
Thanks everyone for the help. Next time I'll be sure not to put in the wrong firmware!
Click to expand...
Click to collapse
Glad to see you got it resolved! I've recommended that service to a few. Thanks for posting. Many don't so we never know the final outcome. This helps the whole community. Enjoy your great phone.
Hey folks,
I was trying to flash a custom kernel (Phenomenal Extreme 4.0) from Clockworkmod on a rooted stock 4.1.2 rom and kernel. I placed the zips on my sd card, then flashed, but it was unsuccessful. Then, when I rebooted from CWM's main menu, the phone went dead. Nothing worked, no buttons, no nothing. Any combination I tried failed, from a simple reboot, to reboot into recovery, to a reboot into download mode. Took battery out, and placed it back in, still nothing.
I'd appreciate any help you can give me! If there's anything like a factory cable, that is still better than nothing. I think I bricked it, and no warranty (Samsung's 3 month is quite short). When I plug the phone in, the laptop responds with a sound but it's not the usual sound when you dock the device. A balloon says that device driver installation failed. Then nothing happens. In any case, I rooted it and there's a flash counter of 1 on it, even if I'm running stock everything. Again, I appreciate any help!
seokhun said:
Hey folks,
I was trying to flash a custom kernel (Phenomenal Extreme 4.0) from Clockworkmod on a rooted stock 4.1.2 rom and kernel. I placed the zips on my sd card, then flashed, but it was unsuccessful. Then, when I rebooted from CWM's main menu, the phone went dead. Nothing worked, no buttons, no nothing. Any combination I tried failed, from a simple reboot, to reboot into recovery, to a reboot into download mode. Took battery out, and placed it back in, still nothing.
I'd appreciate any help you can give me! If there's anything like a factory cable, that is still better than nothing. I think I bricked it, and no warranty (Samsung's 3 month is quite short). When I plug the phone in, the laptop responds with a sound but it's not the usual sound when you dock the device. A balloon says that device driver installation failed. Then nothing happens. In any case, I rooted it and there's a flash counter of 1 on it, even if I'm running stock everything. Again, I appreciate any help!
Click to expand...
Click to collapse
What forum did you find that kernel? Hopefully it was made for d2tmo.
+Bound for Valhalla!
I just checked, it wasn't. It's actually made for the international version -- my fault. Oh crap, I'm totally screwed, aren't I? *rolling eyes and a long sigh*
http://forum.xda-developers.com/showthread.php?t=1917234 My question is, it failed regardless, and why would it die AFTER I reboot the phone? It should've died right when I tried to install it through CWM.
seokhun said:
I just checked, it wasn't. It's actually made for the international version -- my fault. Oh crap, I'm totally screwed, aren't I? *rolling eyes and a long sigh*
http://forum.xda-developers.com/showthread.php?t=1917234 My question is, it failed regardless, and why would it die AFTER I reboot the phone? It should've died right when I tried to install it through CWM.
Click to expand...
Click to collapse
Google jtag repair.
That's an expensive paper weight.
|When Emotion Goes Up, Logic Goes Down|
I made a Nandroid before messing around.
Once I do the JTAG repair, can I restore using that Nandroid after re-rooting and flashing CWM? The guy who will be doing the JTAG said that it's dangerous because there's a risk of bricking involved.
I would just restore things individually, personally. I don't know what you had on there, but is there anything that you can't restore some other way ?
That happened to me when i flash wromg kernel. And I had a panic attack...but I somehow manage to go into recovery mod....if you can go into recovery mod...have no fear back up is there lol
Just wipe everything and restore your backup.
Sent from my SGH-T999 using xda premium
Send it back
Sent from my SGH-T999 using xda premium
seshaz said:
Send it back
Sent from my SGH-T999 using xda premium
Click to expand...
Click to collapse
Hopefully you can get odin to recognise it...
tdotdot said:
Hopefully you can get odin to recognise it...
Click to expand...
Click to collapse
I had the same problem when I first got my S3. I flashed a file that was for my S2 not realizing and the phone responded the same way or didnt respond at all. Im not saying this will work but you can try. Do the proper button combo to get into download. It wont show anything on your scrren but the phone could still be in download mode. Go ahead and try connecting it to your computer and see if odin will recognize it. Make sure you have your drivers installed and dont forget to push volume up to get all the way into download mode. It worked for me once before and I hope to never have to try it again. If you have already tried this then your out of luck and will have to jtag.
JTAG is no scam. It is a VERY reliable source! Go for it.
Sent from my Galaxy Nexus using xda premium
Never mind, warranty exchange. I don't want to send my phone to strangers, even if it's legitimate. Still $45-$60 on the credit card.
I have a question though, as long as the phone is under warranty, I can exchange for a replacement an unlimited number of times, right?
Warranty Exchange!
seokhun said:
Never mind, warranty exchange. I don't want to send my phone to strangers, even if it's legitimate. Still $45-$60 on the credit card.
I have a question though, as long as the phone is under warranty, I can exchange for a replacement an unlimited number of times, right?
Click to expand...
Click to collapse
Yes you can...I did it with my S2 until I got one that did'nt have any signs of being refurbished. It looked brand new! I have even told them that something was wrong with the phone (hardware issue) when there was nothing wrong just because the one year warranty was about to run out and it had a few cosmedic blemishes..I have given them a lot of money in the past 9 years so I do'nt feel too bad... I did it with my Vibrant as well.
I've done my fair share of searching and I couldn't come up with much so I strongly believe I have a unique problem. I hope someone can point me in the right direction
Im have a rooted GS3 747 running Paranoid Android. A couple days ago the phone wouldn't charge. I tried different cables and batteries and after some testing with other GS3's I realized that my phone's charging port was broken. As a result I couldn't even connect my phone to the computer to unroot it with odin. I want to unroot so I can send in the phone for repair under warranty. So I downloaded mobile odin pro and proceeded to unroot my phone. I copied the original rogers rom to the external sd, followed the instructions and started the process. Everything looked like it was going fine until I got stuck on the samsung screen. Did some more research and learned that I had to do a factory data restart by booting into recovery mode. Did that. By now I'm feeling pretty good about all this. I followed the instructions all the way and I'm thinking that I'm gonna get a stock phone shortly. Wrong! The phone was still stuck on the samsung screen.
Now since I cant connect my phone to the PC cuz the charging port is broken I dont know what to do. I would have just flashed Clockwork Mod like I did when I first rooted and started all over but I cant.
If no one has a solution then Im just thinking of sending it in as is. Maybe they wont be able to see that the phone is rooted since they wont be able to connect it their PC without swapping out the motherboard to fix the problem.
I should add that I went to a repair store to try and fix it and they told me that the only way would be swap out your mobo.
machdown said:
I've done my fair share of searching and I couldn't come up with much so I strongly believe I have a unique problem. I hope someone can point me in the right direction
Im have a rooted GS3 747 running Paranoid Android. A couple days ago the phone wouldn't charge. I tried different cables and batteries and after some testing with other GS3's I realized that my phone's charging port was broken. As a result I couldn't even connect my phone to the computer to unroot it with odin. I want to unroot so I can send in the phone for repair under warranty. So I downloaded mobile odin pro and proceeded to unroot my phone. I copied the original rogers rom to the external sd, followed the instructions and started the process. Everything looked like it was going fine until I got stuck on the samsung screen. Did some more research and learned that I had to do a factory data restart by booting into recovery mode. Did that. By now I'm feeling pretty good about all this. I followed the instructions all the way and I'm thinking that I'm gonna get a stock phone shortly. Wrong! The phone was still stuck on the samsung screen.
Now since I cant connect my phone to the PC cuz the charging port is broken I dont know what to do. I would have just flashed Clockwork Mod like I did when I first rooted and started all over but I cant.
If no one has a solution then Im just thinking of sending it in as is. Maybe they wont be able to see that the phone is rooted since they wont be able to connect it their PC without swapping out the motherboard to fix the problem.
I should add that I went to a repair store to try and fix it and they told me that the only way would be swap out your mobo.
Click to expand...
Click to collapse
You will want to be sure that your flash counter says 0. This can be found by entering download mode (vol down, home, power) and you will see "custom binary count". that is how they will tell that you have rooted. Have you entered recovery and done a factory reset to get past the boot screen? If you can full wipe/ factory reset and get back into Android, I recommend you use "triangle away" app to clear your flash counter.
BCSC said:
You will want to be sure that your flash counter says 0. This can be found by entering download mode (vol down, home, power) and you will see "custom binary count". that is how they will tell that you have rooted. Have you entered recovery and done a factory reset to get past the boot screen? If you can full wipe/ factory reset and get back into Android, I recommend you use "triangle away" app to clear your flash counter.
Click to expand...
Click to collapse
I entered download mode and dont see flash counter anywhere. I got the warning screen were you have the option to restart or download.
Ya I entered recovery and did a factory reset but nothing. Really cant do anything with charging port broken.
I sent it in anyways for repairs. Hopefully they just replace it
I'm having the same problem with my Gs3 with CM10 4.2.2 running. Thought this would help.
Sent from my SPH-L710 using xda app-developers app