Develop Bugs

[Q] T-Mobile Samsung Galaxy S II soft brick

OK I was trying to flash an unlocked kernal via ODIN last night, something went wrong and now phone is stuck on the phone--!--computer screen. I cannot get past this screen. vol+home+power doesn't do anything but loop to the same screen.
It shows ODIN MODE in red at the top of the screen, but ODIn won't recognize the phone, nor will Kies (not running at the same time). Computer makes USB connected/disconnected sound when I plug and unplug the phone.
I have tried One-Click Unbrick, did not recognize that phone was connected.
Help!!

which model of Galaxy S2 do you have?

T-Mobile SGH-T989

hose902 said:
T-Mobile SGH-T989
Click to expand...
Click to collapse
there''s currently nothing to flash this phone
it came out only 2 days ago
DEV are still working on finding root
so, the best suggestion is to take it back to the store and get it exchanged
or wait a few more days/weeks until a flashable release becomes available to fix the mistake

I know, I was hasty and now this. Even when there something available to flash, the device isn't being recognized by ODIN. Any troubleshooting help for this?

When I managed to get my Vibrant into that mode I could pull the battery, hold volume up, put the battery in, press and release power (still holding volume up) and it'd kick back into download mode everytime. Once in download mode I could plug the USB in and a running ODIN would see it pop up. If ODIN wasn't running and USB was already plugged in things wouldn't work right.
I haven't tried ODIN on the GS2 yet (I'll wait for a root ). I did find the vibrant nearly impossible to brick though... trust me I unexpectedly tried quite hard.
You might need the newest ODIN for GS2 support, and possibly newer drivers.

Hey, Hey, Hey...
My Story...
1. I got a TMO Samsung Galaxy S2
2. Tried to root
3. Used Odin to root and install ROM and referenced the following thread: http://forum.xda-developers.com/showthread.php?t=1095274
4. Realized phone models are not the same
5. Phone does not boot and nothing comes up on the screen
6. No lights or LED indicators (i.e. charging) HOWEVER....
7. ODIN recognizes the phone when I plug in the phone via USB
8. Tried to load stock rom:http://forum.xda-developers.com/showthread.php?t=1321811
9. ODIN gets stuck on <ID:0/005> SetupConnection...
10. I am unable to access SD Card for CWR
11. Next step? Return or exchanges are currently not an option.
Thanks in advance for the assistance!

fix4tv said:
Hey, Hey, Hey...
My Story...
1. I got a TMO Samsung Galaxy S2
2. Tried to root
3. Used Odin to root and install ROM and referenced the following thread: http://forum.xda-developers.com/showthread.php?t=1095274
4. Realized phone models are not the same
5. Phone does not boot and nothing comes up on the screen
6. No lights or LED indicators (i.e. charging) HOWEVER....
7. ODIN recognizes the phone when I plug in the phone via USB
8. Tried to load stock rom:http://forum.xda-developers.com/showthread.php?t=1321811
9. ODIN gets stuck on <ID:0/005> SetupConnection...
10. I am unable to access SD Card for CWR
11. Next step? Return or exchanges are currently not an option.
Thanks in advance for the assistance!
Click to expand...
Click to collapse
I'm a bit new to this, but a custom ROM shouldn't affect your recovery mode. Are you sure you are using the correct buttons and methods to boot recovery?
Might want to make a new thread instead of necroing something from when the phone was 2 days old.

I have GT I9100 and done the same thing and got the same result . stuck at setup connection with odin
Please Help

Go into device manager when is plugged in and if it says qhd-usb or something like that its a hard brick. What tipped me off was you said it makes two noises when you plug in. that's a tell tell sign your hard bricked
Sent from my SGH-T989 using xda premium

soft bricked my phone (i hope)
i have sgh-t989 (t-mobile) i am running a miui rom. it wont boot it just goes to miui boot up screen. i can go to the download mode but not recovery (how do u do that) but when im in downoad mode Odin dosnt recognize my phone. and my computer says it is an unknown device.
tried new wire, uninstalling re-installing kies, stopped all processes, diff computer tried to boot for a day, let battery out for a day, and a few other things.
please help and thank you.

iamnoone626 said:
i have sgh-t989 (t-mobile) i am running a miui rom. it wont boot it just goes to miui boot up screen. i can go to the download mode but not recovery (how do u do that) but when im in downoad mode Odin dosnt recognize my phone. and my computer says it is an unknown device.
tried new wire, uninstalling re-installing kies, stopped all processes, diff computer tried to boot for a day, let battery out for a day, and a few other things.
please help and thank you.
Click to expand...
Click to collapse
You should try to uninstall then reinstall driver, and try another usb port. In my experience, Odin seems to be picky, it only recognizes your phone if you plug it in the usb port that you used in the first time.
Sent from my SAMSUNG-SGH-T989 using xda app-developers app

Recovery is accessed by holding both vol + and - while starting the phone. Hold them both while pressing the power button, then release the power button when it vibrates, keep holding the vol buttons till you see the recovery screen.

Alarmmy said:
You should try to uninstall then reinstall driver, and try another usb port. In my experience, Odin seems to be picky, it only recognizes your phone if you plug it in the usb port that you used in the first time.
Sent from my SAMSUNG-SGH-T989 using xda app-developers app
Click to expand...
Click to collapse
ok i have done this through kies is there another way that you can do this?
---------- Post added at 09:34 AM ---------- Previous post was at 09:26 AM ----------
nagoshi said:
Recovery is accessed by holding both vol + and - while starting the phone. Hold them both while pressing the power button, then release the power button when it vibrates, keep holding the vol buttons till you see the recovery screen.
Click to expand...
Click to collapse
when i do this it only takes me to download mode.

Have a look at http://forum.xda-developers.com/showthread.php?t=1513359
for a DL link for the USB Drivers
Cheers,
Chris

Sk3tchy said:
Have a look at http://forum.xda-developers.com/showthread.php?t=1513359
for a DL link for the USB Drivers
Cheers,
Chris
Click to expand...
Click to collapse
i tryed this but still odin does not recognize my phone. (no yellow box shows up)

[HOWTO] Change from Yakju** to Yakju

After going from one thread to the other i was able to do it myself so I've decided to put it all under 1 thread... Unzip all the files you download
WARNING!!!! I AM IN NO WAY RESPONSIBLE TO WHATEVER HAPPENS TO YOUR PHONE!!!
Step ONE :
Download the USB driver and firmware files to Windows. ( USB DRIVERS) ( FIRMWARE)
Run USB driver app in Windows, reboot Windows.
Run firmware app in Windows.
Put phone in download mode (power off, volume down + power on, plug USB cable in)
in firmware app, click start!
And you're done!
You're now yakju with latest Google ITL41F.
For those who are having issues with the "R" icon for roaming on Fido,rogers,Wind,Mobilicity etc etc .. follow the instructions below
You will need to unlock your bootloader and the following files:
1: FASTBOOT
2: UGLK1 RADIO
Unlock Galaxy Nexus Bootloader
Below’s a step by step guide for folks who’re not much familiar with fastboot and stuff like that. Here you go:
Put your phone in fastboot mode:
Switch off your phone
Hold the Volume Up Key + Volume Down Key and then press the Power button.
You’ll now see a Android robot. And text below it would read “FASTBOOT MODE” in red.
Extract the Fastboot.zip file on your PC
Now open the Fastboot folder ─ hold Shift key and Right click at any empty space inside the folder, and select “Open command window here“
Now connect your phone to your PC using USB cable, and then type fastboot devices in the command prompt to make sure your device is recognized.
And now to unlock the bootloader, type this in the command prompt:
fastboot oem unlock
Accept the request on your phone by selecting Yes using the Volume button and then press the Power button to confirm. (Keep CMW opened as you'll need it for people with the roaming issues)
Next you will want to "Flash" the UGLK1 Radio. To do so follow the instructions below:
In CMW after you have unlocked your bootloader, Type:
fastboot flash radio <radio-maguro-i9250ugkl1.img> without the "<>"
Then
fastboot oem lock (to relock your bootloader)
Enjoy your new Galaxy Nexus updated by Google!

Will rooting/unlocking the bootloader void the warranty? Any way around this?

SL1VR said:
Will rooting/unlocking the bootloader void the warranty? Any way around this?
Click to expand...
Click to collapse
Technically yes, but you can always relock and flash back to the stock images, effectively returning it to out of the box stock.

cheers
its works
used it here
http://forum.xda-developers.com/showthread.php?p=21849452#post21849452
Samsung UK repair centre is going to get a mega telling off from samsung
as THEY sent it out back to me bootloader unlocked !

Thanks, worked perfectly for me. Got a notification of an update too.
But when I went to go update in the middle of the update it just stopped half way through with a big red triangle with a "!" in the centre of it which I assumed ment it didnt work so I restarted my phone and the notification to update never came back

jonnyg1097 said:
Thanks, worked perfectly for me. Got a notification of an update too.
But when I went to go update in the middle of the update it just stopped half way through with a big red triangle with a "!" in the centre of it which I assumed ment it didnt work so I restarted my phone and the notification to update never came back
Click to expand...
Click to collapse
Search for the update manually
Go to menu>settings>about phone>update>check for updates
Sent from my GT-P7500 using Tapatalk

cirian75 said:
cheers
its works
used it here
http://forum.xda-developers.com/showthread.php?p=21849452#post21849452
Samsung UK repair centre is going to get a mega telling off from samsung
as THEY sent it out back to me bootloader unlocked !
Click to expand...
Click to collapse
glad it helped you
Sent from my GT-P7500 using Tapatalk

alas1986 said:
Search for the update manually
Go to menu>settings>about phone>update>check for updates
Sent from my GT-P7500 using Tapatalk
Click to expand...
Click to collapse
I've done that, says I have the latest version even after rebooting the phone.

jonnyg1097 said:
I've done that, says I have the latest version even after rebooting the phone.
Click to expand...
Click to collapse
What version do you see in about phone ?
Sent from my Galaxy Nexus using Tapatalk

jonnyg1097 said:
I've done that, says I have the latest version even after rebooting the phone.
Click to expand...
Click to collapse
You could try to factory reset your phone also
Sent from my Galaxy Nexus using Tapatalk

alas1986 said:
What version do you see in about phone ?
Sent from my Galaxy Nexus using Tapatalk
Click to expand...
Click to collapse
My build number is ITL41F
alas1986 said:
You could try to factory reset your phone also
Sent from my Galaxy Nexus using Tapatalk
Click to expand...
Click to collapse
Tried that one too still didnt work

jonnyg1097 said:
My build number is ITL41F
Tried that one too still didnt work
Click to expand...
Click to collapse
You can trying downloading it from here
http://code.google.com/android/nexus/images.html
And manually flash it
Sent from my Galaxy Nexus using Tapatalk

Nice how to, thank you!

does this tutorial apply to YAKJUSC too? mine is 4.0.1..
thanks

Yes, the porting process is the same.

Big thanks. I used the procedure last night successfully. Also got update 4.0.2 after few minutes. I had little issues with bluetooth while connecting to my BlueAnt 4S. But it seems to be working fine now.
PS: Forgot to mention that battery life has improved considerably after this flashing.

rookie8155 said:
Big thanks. I used the procedure last night successfully. Also got update 4.0.2 after few minutes. I had little issues with bluetooth while connecting to my BlueAnt 4S. But it seems to be working fine now.
PS: Forgot to mention that battery life has improved considerably after this flashing.
Click to expand...
Click to collapse
I'm glad the guide helped you
Sent from my Galaxy Nexus using Tapatalk

hey i have tryed that and it didint work im still stuck on "yakjuxw"
getting 0 succeed and 0 failed on the firmware app
i have all drivers
any ideas?

Galaxy98 said:
hey i have tryed that and it didint work im still stuck on "yakjuxw"
getting 0 succeed and 0 failed on the firmware app
i have all drivers
any ideas?
Click to expand...
Click to collapse
I got the same problem
EDIT: I have rebooted my phone, and restarted all over. I worked

I am not exprt but looks like your phone drivers ste not loading properly. I had same issue but then I waited for the drivers to load on my pc and then pressed start button again and it stsrted working .
I would suggest that you conect your first snd let windows load drivers. When you drivers are loaded then follow the procedure .

[q] radio messed up?

I have a galaxy s 2 tmobile version rooted and running beastmod 5.0
So I'm having a problem. I flashed the ics roms to my t989. I was running bm 5 before. I called the #2632* thingy to just get edge instead of 4g because it was killing my battery. I decided to go back to bm 5 cuz the ics ports based on the att leak were horrible. Usually on bm 5 I have GSM only selected for the network but it hasn't been able to connect. The only way I can connect is by using wcdma/gsm auto mode to connect to T-Mobile then I can select GSM only to just use GSM. If I restart with GSM only again it wont find signal unless wcdma/GSM is seleceted then I switch to GSM only. Idk what to do anymore GSM only used to work before I flashed ics and this is pissing me off help me anyone please! Its greatly appreciated.

Did you flash a gingerbread radio before going back to bm?

I did I found the t989 radio on xda I flashed it and it didn't work its the same problem.

joeloe03 said:
I did I found the t989 radio on xda I flashed it and it didn't work its the same problem.
Click to expand...
Click to collapse
And what does your baseband say right now?

I attached a picture.

Super wipe, factory reset, flash back to stock with Odin, etc
Sent from my SAMSUNG-SGH-T989 using xda premium

What's a super wipe. Where can I find it and how do I do the rest. I tried it like go back to stock but Idk if it worked I need help

joeloe03 said:
What's a super wipe. Where can I find it and how do I do the rest. I tried it like go back to stock but Idk if it worked I need help
Click to expand...
Click to collapse
Hit the darkside part of my siggy and look over the OP. Superwipe is a script by tdj recommended prior to any ROM flash.

joeloe03 said:
What's a super wipe. Where can I find it and how do I do the rest. I tried it like go back to stock but Idk if it worked I need help
Click to expand...
Click to collapse
Super wipe:
Thank TDJ!!
http://forum.xda-developers.com/showthread.php?t=1477955
Boot into CWM.......wipe data/factory reset
Flash darkside superwipe
Back to stock:
Ok, you are going to need the drivers for your phone. http://www.samsung.com/us/kies/
You need odin as well, download it. http://www.mediafire.com/?u868rqz4qn0ta34
If you already have drivers and odin move on to below
Go here http://www.sammobile.com/firmware/ and make an account. I use sammobile because it contains everything in one shot. No need to get radio and crap from other places. After you make an account go to firmware section and type t989 in the search box. download the t989uvkid or Kl1 ASSUMING YOU HAVE AMERICAN T989
After you have completed the download you are going to need to unzip it with 7zip to extract the tar.
Plug the USB cable into your computer, without plugging it into your phone.
Hold VOL UP + VOL DOWN while plugging in the USB cable to your phone. Stop holding buttons when the ''Warning'' appears.
Press Volume UP and open ODIN (Run as Admin on Vista and 7, just to be safe)
Click PDA and locate the MD5 file you extracted earlier.
WAIT FOR ODIN TO RECOGNIZE YOUR PHONE. THE COM PORT WILL TURN YELLOW AND HAVE A NUMBER
MAKE SURE NOTHING BUT AUTO REBOOT IS CHECKED!!!!!!!
Press 'Start' and be patient. It will take a few minutes because it is a large file.
phone will reboot automatically.

thank so much for the instructions however
this llink doesnt work for the DRIVERS doesnt work
and i had the superwipe already and thanks lol silly me.

If you go to Samsung website and download Kies, the drivers will automatically update.

joeloe03 said:
thank so much for the instructions however
this llink doesnt work for the DRIVERS doesnt work
and i had the superwipe already and thanks lol silly me.
Click to expand...
Click to collapse
Fixed link

Okay. Thanks and the drivers what do I do with them??

xcrazydx said:
Super wipe:
Thank TDJ!!
http://forum.xda-developers.com/showthread.php?t=1477955
Boot into CWM.......wipe data/factory reset
Flash darkside superwipe
Back to stock:
Ok, you are going to need the drivers for your phone. http://www.samsung.com/us/kies/
You need odin as well, download it. http://www.mediafire.com/?u868rqz4qn0ta34
If you already have drivers and odin move on to below
Go here http://www.sammobile.com/firmware/ and make an account. I use sammobile because it contains everything in one shot. No need to get radio and crap from other places. After you make an account go to firmware section and type t989 in the search box. download the t989uvkid or Kl1 ASSUMING YOU HAVE AMERICAN T989
After you have completed the download you are going to need to unzip it with 7zip to extract the tar.
Plug the USB cable into your computer, without plugging it into your phone.
Hold VOL UP + VOL DOWN while plugging in the USB cable to your phone. Stop holding buttons when the ''Warning'' appears.
Press Volume UP and open ODIN (Run as Admin on Vista and 7, just to be safe)
Click PDA and locate the MD5 file you extracted earlier.
WAIT FOR ODIN TO RECOGNIZE YOUR PHONE. THE COM PORT WILL TURN YELLOW AND HAVE A NUMBER
MAKE SURE NOTHING BUT AUTO REBOOT IS CHECKED!!!!!!!
Press 'Start' and be patient. It will take a few minutes because it is a large file.
phone will reboot automatically.
Click to expand...
Click to collapse
So now I download kies open kies plug my phone in in the download mode for it to send the drivers over. Then what? How do I do the drivers

joeloe03 said:
So now I download kies open kies plug my phone in in the download mode for it to send the drivers over. Then what? How do I do the drivers
Click to expand...
Click to collapse
You dont do anything with it. kies installed the drivers already. just follow the directions in my post

xcrazydx said:
You dont do anything with it. kies installed the drivers already. just follow the directions in my post
Click to expand...
Click to collapse
okay but once i download kies do i plug in the phone and let it install just while the phone is on then unplug it turn it off go into download mode and open odin?

joeloe03 said:
okay but once i download kies do i plug in the phone and let it install just while the phone is on then unplug it turn it off go into download mode and open odin?
Click to expand...
Click to collapse
It doesn't matter. Just follow the directions. I've already broke it down barney style and explained it in more detail than anyone else ever has. Spent a decent amount of time to help you, and you have yet to even push the button and give me a simple thanks. Geeze man

xcrazydx said:
It doesn't matter. Just follow the directions. I've already broke it down barney style and explained it in more detail than anyone else ever has. Spent a decent amount of time to help you, and you have yet to even push the button and give me a simple thanks. Geeze man
Click to expand...
Click to collapse
okay thank you i appreciate your invested time and trying to help me im at school so when i get home i will do this, im a big noob as this stuff. thanks again

joeloe03 said:
okay thank you i appreciate your invested time and trying to help me im at school so when i get home i will do this, im a big noob as this stuff. thanks again
Click to expand...
Click to collapse
Thanks
If you really need it I may be able to walk you through it on here. But you should have no problem if you follow the instructions.
http://webchat.irondust.net/?channels=skyrocket
Pm me if you need help and i'll try to get on

Or you could've used my sticky. http://forum.xda-developers.com/showthread.php?t=1513359

[Q] [HELP] Gnex bricked

I was using PA rom (3.69) with Franco kernel, my recovery was TWRP 2.6.0.0
yesterday I was backing up my sd card (I'm doing it every 2 months) and then some error was showing up an my pc's screen I don't really remember what the error said but I found out that was from my twrp folder, so to find what happend I just wanted to boot up into the recovery and then my nexus wont boot up I found out that my Gnex was hard bricked (with no reason why) so I used this page (http://forum.xda-developers.com/showthread.php?t=1760787/) to unbrick and it helped alot but I can't find my backups , and when I'm trying to boot into Fastboot,the recovery or even to reboot, it's funny that my nexus was working excellent befor what happend :crying: (btw my nexus was pluged to my pc when i tried to boot into twrp)
so yeah can not do anything I'm stuck with a broken PA (all my apps are still installed but I can not find my backups)
CAN SOMEONE PLEASE HELP ME !!!!
My Device : White Galaxy nexus (takju) 16GB
Rom: PA: latest 4.2.2
Kernel: Franco latest
Recovery: Stupid TWRP (I'm going back to CWM after this)

There is no possible way in hell to brick a gnex unless your NAND fries lol, download mode is hard coded into the chips and you can always get into it no matter what happens. I suggest using ODIN and flashing all the factory images, there are guides floating around, a factory reset usually fixes all your problems
Sent from my Galaxy Nexus VZW @1.2 GHz on Stock 4.3

seldom ssightsl
IRX120 said:
There is no possible way in hell to brick a gnex unless your NAND fries lol, download mode is hard coded into the chips and you can always get into it no matter what happens. I suggest using ODIN and flashing all the factory images, there are guides floating around, a factory reset usually fixes all your problems
Sent from my Galaxy Nexus VZW @1.2 GHz on Stock 4.3
Click to expand...
Click to collapse
I can't go into download mode :crying:

How can I know that my NAND fried??
EDIT I have the same problem that the user rekrapg had but I don't have my backups anymore

Wait what? So what exactly happens when you try and get in to fastboot?

GldRush98 said:
Wait what? So what exactly happens when you try and get in to fastboot?
Click to expand...
Click to collapse
nothing happened

Are you sure that is ur battery not working anymore?

e753 said:
Are you sure that is ur battery not working anymore?
Click to expand...
Click to collapse
my battery was on 97%

Well I guess that my Gnex Was killed, I can't even use the OMAP Flash
guessing that twrp killed it

So, you take out the battery, put it back in, hold vol+ and vol- and then hit the power button, and absolutely nothing happens? The screen doesn't come on at all?
What if you take the battery out, put the batter back in, and plug it in to the wall charger (don't try and turn it on). Have you left it on the wall charger for a couple hours?

GldRush98 said:
So, you take out the battery, put it back in, hold vol+ and vol- and then hit the power button, and absolutely nothing happens? The screen doesn't come on at all?
What if you take the battery out, put the batter back in, and plug it in to the wall charger (don't try and turn it on). Have you left it on the wall charger for a couple hours?
Click to expand...
Click to collapse
I tried that method and it didn't work.
I know very well how to use android (I used android for 3 years) and I never saw this thing before ,It's weird that you can not even brick (Kill) nexus devices.

It's alive !!!! Alive !!!!!!!!!
So I searched a bit on xda and found some helpful Pages
http://forum.gsmhosting.com/vbb/f63...9250-galaxy-nexus-gt-i9100g-gt-i9300-1465412/
and
http://forum.xda-developers.com/showthread.php?t=2065470
and it helped

flash stock rom with toolkit

KnighthooD said:
flash stock rom with toolkit
Click to expand...
Click to collapse
already did that

I have the same thing with a buddies GNex. I flashed stock images using a toolkit, nada. SuperWiped, flashed stock, nada. Even did an ODIN flash several times, and still nothing.
We can boot into Fastboot and various custom recoveries, but nothing is booting.

player911 said:
I have the same thing with a buddies GNex. I flashed stock images using a toolkit, nada. SuperWiped, flashed stock, nada. Even did an ODIN flash several times, and still nothing.
We can boot into Fastboot and various custom recoveries, but nothing is booting.
Click to expand...
Click to collapse
Did you do what i am going to mention?
Part 1:
Now you will need these things before you're proceeding
**USB cable**
**I suggest using windows 7 (because my windows 8 pc didn't install the drivers)**
**A bricked Gnex (of course) without the battery installed **
** and these files "https://www.dropbox.com/sh/owi65iy2xvvpzf0/i5rgGJFJwO" **
1 go ahead and download the files that I provided
2 extract the "9250 omapflash_tuna.zip" to the desktop (recommend)
3 go into your device manager [Control Panel ---> Hardware and Sound ---> Device Manager]
4 go to Actions Menu and select Add Legacy Hardware then click on add manually double click on Snow All Devices, Have Disk, now go into the omapflash folder and choose "usb_drv_windows", "omap_winusb.inf".
Now now, it will take some time so please be patient .
5 after the drivers are installed plug in the Gnex into the USB cable that you have.
6 go back to the omapflash folder and open the "omap4460_tuna_hs_pro.bat" it will some scripts that will "semi unbrick" your nexus
7 close the .bat program and install back the battery to your nexus and boot into DOWNLOAD MODE (if your gnex had USB debugging on before it was bricked, if not boot into your rom and enable it and then afterwards
perform 1-6 if your nexus can't boot back into download mode)
Part 2:
**you will need t charge your Gnex to 80%-90%**
**you will need your Gnex installed USB drivers on your pc (the best way is to install kies)**
1 unzip the second zip file "Odin.stock Gnex I9250 4.3" to the desktop (again recommend)
2 open the folder and then open "Odin307" after that open Odin307.exe (once your phone is successfully connected to your pc, the ID:COM box on ODIN will turn blue and will show the COM port number)
3 click the PIT icon and choose "I9250_partition-table-0915.pit" from the ODIM folder
then click the PDA box. then click the button and choose "odin.takju.4.3.tar.md5"
4 now click on start button and it will fully unbrick you Sexy Galaxy Nexus (don't be afraid it will take some minutes)
plus you just updated to android 4.3
special thanks to samersh72, rekrapg and legija

A little bit bricked phone.

Sorry my english is not the best.
I do yesterday my first root. All going good. I got my phone rooted - New android versioon 4.4.2
But after a few hours I think I change my rom. I looking a youtube a good video. I find it.
I do all like video if im completed I restart my phone and after this my phone is bricked.
http://forum.xda-developers.com/showthread.php?t=2565752 - i try this on my phone. Yes, this is bad way but know is too late.
Phone is turned on but no picture. If I do that: Press and hold volume donw and connect your device to computer with micro usb cable I see some options.
Like that:
- Start
- Restart bootloader
- Recovery mode
- Power off
But i dont know what i need to do next. Somebody help me please?
I hope you guys understand my bad english and my probleem.
Yes, i am dumbass.

I think U must go back to stock rom and start from zero
Here´s a guide for it: http://forum.xda-developers.com/showthread.php?t=2498102
:good:
Good luck
<AhhA> said:
Sorry my english is not the best.
I do yesterday my first root. All going good. I got my phone rooted - New android versioon 4.4.2
But after a few hours I think I change my rom. I looking a youtube a good video. I find it.
I do all like video if im completed I restart my phone and after this my phone is bricked.
http://forum.xda-developers.com/showthread.php?t=2565752 - i try this on my phone. Yes, this is bad way but know is too late.
Phone is turned on but no picture. If I do that: Press and hold volume donw and connect your device to computer with micro usb cable I see some options.
Like that:
- Start
- Restart bootloader
- Recovery mode
- Power off
But i dont know what i need to do next. Somebody help me please?
I hope you guys understand my bad english and my probleem.
Yes, i am dumbass.
Click to expand...
Click to collapse

ErnestoD said:
I think U must go back to stock rom and start from zero
Here´s a guide for it: http://forum.xda-developers.com/showthread.php?t=2498102
:good:
Good luck
Click to expand...
Click to collapse
Thank you.
I look one fail i downloaded it's here http://forum.xda-developers.com/showthread.php?t=2498102&page=12 i understand this a little bit more.
but my question is 3. Download drivers, LG Mobile Support Tool, patch and flashing tool where i get best driver and patch and flashing tool on my phone? Do you know?

<AhhA> said:
Sorry my english is not the best.
I do yesterday my first root. All going good. I got my phone rooted - New android versioon 4.4.2
But after a few hours I think I change my rom. I looking a youtube a good video. I find it.
I do all like video if im completed I restart my phone and after this my phone is bricked.
http://forum.xda-developers.com/showthread.php?t=2565752 - i try this on my phone. Yes, this is bad way but know is too late.
Phone is turned on but no picture. If I do that: Press and hold volume donw and connect your device to computer with micro usb cable I see some options.
Like that:
- Start
- Restart bootloader
- Recovery mode
- Power off
But i dont know what i need to do next. Somebody help me please?
I hope you guys understand my bad english and my probleem.
Yes, i am dumbass.
Click to expand...
Click to collapse
Did you a backup ? You can try push a custom rom via adb and install it via recovery. Which recovery do you use?

I dont have backup and cant rembmer which recovery
And im not the best if this things. I need more explanation

1. Delete all LG software from PC and reboot - DONE
2. Download KDZ you want - DONE
3. Download drivers, LG Mobile Support Tool, patch and flashing tool
Drivers - DONE
Mobile support - DONE
Patch - what was it? Please download link
Flashing tool - what was it? Please download link
Im stuck at point 3. Stupid my english. I don't understand, patch and flashing tool. Where i find it.