Develop Bugs

Qtek 9090 Dead - Update not 100%, no reaction, no bootloader

Hey guys,
I've searched the forum for like 5 hours or so
to find a thread that could help me solve this solution...
I've tried everything that had something to do with "dead"
in the BlueAngel and Blueangel Update etc. section
What it does:
- The screen stays black
- If I try to charge, the Red 'Charging' LED doesn't become red
unless I take the battery out of the Qtek and charge..
Then it gets red (WEIRD)
- No connection with activesync or rom update utilities
What happened:
- Rom update stopped after a few percentages...
If i try to get a new rom in it with or without cradle
with the following rom update utilities:
- BaUpgradeUt.exe:
then I get a Connection Error (101) when I try to update
- MaUpgradeUt_noID.exe:
ERROR 150: ROM UPGRADE UTILITY ERROR
(Rom Utility not designed for this device)
or "Finished" immediately (but it's not finished)
(Depends on the rom I use, and I used like 10 different roms)
Soft reset / Hard reset doesn't work,
I even tried to Hard Reset by holding the
Voice Record button + Power button + Reset button for 2 minutes
(I tried Camera + Power + Reset too) with the battery,
and I tried these without the battery...
No reaction...
If someone can help me, please do...
Thnx in advance

Maybe you can try thingds from this
http://forum.xda-developers.com/viewtopic.php?p=291989#291989

sep said:
Maybe you can try thingds from this
http://forum.xda-developers.com/viewtopic.php?p=291989#291989
Click to expand...
Click to collapse
Nope,
I've tried that too, but I don't get the USB or WCEUSB in mtty...
The COM ports don't react.
I know how to use it, because I used it like 10 times or somethin'
But I think the problem is, that I can't get in the bootloader mode
(or any other mode)... So there's no response from my Angel..
Thanks anyway..

have you tryed to remove battery, leave it without battery fo an hour or two then put the battery back and power on the device ?
this method may boot your device. If it worked go imediately in bot loader mode and reflash your favorite rom
If it does not helps maybe it is hardware problem ... and you should leave your device in service center

Tried this too
Isn't there any solution except for service center?
I want to know how I can solve this problem,
'cause it could happen again when I update the rom later.
And I know I'm not the only one with this problem.
It would help me and a lot of other BlueAngel owners..

Is it possible to make a serial connection with the bottom I/O port and issue the necessary commands with mtty? could be that there is some logic powered on the board but not enough to make the "USB" section powered up.. similar to serial a console cable on network gear etc. OR.. is there any known secrets such as a hardware debug mode initiated with certain pin(s) on the I/O connector.. such as grounding one or two.. any HTC tech documents floating around for troubleshooting?

You are not one with this problem. The same happens with me too.
Let searching for solution together.
If you want you can contact with me by icq: 190812766

hi i had a severe problem flashing my charmer pls help

please any help you can give will be brilliant. i tried falshing it with another rom but my battery died half way through the process and now my mda will only work on the mains supply (not even by a powerd usb hub) when i check under the setting option power it say the battery status is unknown i have another battery monitering application on the device know as batti but even that cannot detect the battery. it does flicker when it is not on the mains but won't hold a stable power i have tried to get it into the boot loader screen but it will only do that via the mains. i have checked the registry on the devicxe it says that there is a battery driver present but i do not know whether it is the correct one. is it possible to flash the rom via an sd card or via any alternaticve means or is there another way i can get my device to realise that it does actulally have a battery also could you please send me registry values for the battery to confirm the entries i have are correct. thank you in advance

I have the same problem, did you manage to get this fixed and if so how?

Bricked hx2110 help

I did a rom upgrade on an hx2110 - installed successfully, but now the only thing I can get the pda to do is go into Pre bootloader mode (i.e. Pre-BL 1.00.02 blue screen). SO I tried the universal bootloader method - makes it all the way to the flashing portion but then does NOTHING - the terminal simply sits there saying "ready" and does not upload anything - the program sees the correct communication port (ie. usb01 or whatever). HOW do I force an upload???
Thanks!
Rusty

On another note - I had purchased a working 2110 with a good mobo to replace this one if the flash is not repairable - is that a difficult procedure? Unfortunately, the 2110 I purchased was not working, but this may still be in the books at a later time, so some info would help.
Thanks!

Rustmonkey said:
I did a rom upgrade on an hx2110 - installed successfully, but now the only thing I can get the pda to do is go into Pre bootloader mode (i.e. Pre-BL 1.00.02 blue screen). SO I tried the universal bootloader method - makes it all the way to the flashing portion but then does NOTHING - the terminal simply sits there saying "ready" and does not upload anything - the program sees the correct communication port (ie. usb01 or whatever). HOW do I force an upload???
Thanks!
Rusty
Click to expand...
Click to collapse
Rusty,
You are so lucky that I experienced this problem and solved it on my own. You did not specify what ROM you were loading, but here is the fix:
First you need to get another pocketpc, hx2000 series like yours that is working.
Put that device into white screen bootloader or pre-BL mode (depending on which device you got to borrow)
Ensure that the battery on that device is 100% charged.
Run the original ROM upgrade for the ROM you wish to install (use PDAViet if it's WM6 and use the HP SP32408 to Run it)
Hit all the Ok screens until it brings you to the one that has the "UPDATE" button.
Remove the working Ipaq from the cradle and place it's 100% battery in you own.
Put your Ipaq into pre-BL mode and put it on the cradle. Press the calendar button to activate the usb drivers.
Once it says "USB", Hit the "UPDATE" button and it will load the proper ROM to your IPaq.
When It is done, perform a hard reset by formatting the PS on the device.
Voila!! Your Ipaq is Un-Bricked!! Put in your original battery and charge it up!
Enjoy!!
Bless...

hi Rustmonkey,
i have the similar things - i made my hx2110 brick when i flashed it with a different language ROM, it went 100% when i flashed the ROM but didn't work at all after that.
the problem is i can get it in the bootloader mode after trying many ways, at the same time the pc can't find any USB device at all.
how to make it work again?
thanks.

reggaepoo said:
Rusty,
You are so lucky that I experienced this problem and solved it on my own. You did not specify what ROM you were loading, but here is the fix:
First you need to get another pocketpc, hx2000 series like yours that is working.
Put that device into white screen bootloader or pre-BL mode (depending on which device you got to borrow)
Ensure that the battery on that device is 100% charged.
Run the original ROM upgrade for the ROM you wish to install (use PDAViet if it's WM6 and use the HP SP32408 to Run it)
Hit all the Ok screens until it brings you to the one that has the "UPDATE" button.
Remove the working Ipaq from the cradle and place it's 100% battery in you own.
Put your Ipaq into pre-BL mode and put it on the cradle. Press the calendar button to activate the usb drivers.
Once it says "USB", Hit the "UPDATE" button and it will load the proper ROM to your IPaq.
When It is done, perform a hard reset by formatting the PS on the device.
Voila!! Your Ipaq is Un-Bricked!! Put in your original battery and charge it up!
Enjoy!!
Bless...
Click to expand...
Click to collapse
You, my good sir, are a genius - worked great! Fixed BOTH 2110s

tangwd898 said:
hi Rustmonkey,
i have the similar things - i made my hx2110 brick when i flashed it with a different language ROM, it went 100% when i flashed the ROM but didn't work at all after that.
the problem is i can get it in the bootloader mode after trying many ways, at the same time the pc can't find any USB device at all.
how to make it work again?
thanks.
Click to expand...
Click to collapse
You're going to need another hx2000 series to make sure the battery is fully charged - put the battery in and then use the bootloader keystrokes immediately (contacts+itask+reset) - you made need to tap reset a few times while holding the other two to get it to work. After it is in bootloader mode, push the calander button while it is connected to the cradle/usb to get the pc to recognize it

Rustmonkey said:
You're going to need another hx2000 series to make sure the battery is fully charged - put the battery in and then use the bootloader keystrokes immediately (contacts+itask+reset) - you made need to tap reset a few times while holding the other two to get it to work. After it is in bootloader mode, push the calander button while it is connected to the cradle/usb to get the pc to recognize it
Click to expand...
Click to collapse
really amazing !!!!!!
I just saved my hx2110 as per your step by step instruction now.
Thank you very much.

ok, well, I thought they were fixed... now one of them freezes at the bootup screen, even when I do a clean reset... I've tried reflashing multiple times to no avail... any ideas whats going on?

ok, got everything working - reflashed the non-working one back to an original 2003 rom - which made if freeze at boot - then upgraded it via pre-bl to 1.00.00.L - from here, it wouldn't do anything after filling the bar at the boot screen, but it didn't CRASH (as in lights out) - so I ran the pre-bl again and ran the flash program for 1.00.00.L again WITHOUT swapping between the 2495 and the 2110 - just put the 2110 in pre-bl and away we went - flashed, formatted, and booted - then proceed to upgrade to WM6 via 1.00.00.H --> 1.02.00.H --> WM6 - works GREAT!!!
Thanks for the help everyone!

Dear All,
I`ve got the same problem but i don`t have a second ipaq.. is there anyway to repair it with out the second device???
Thank you very much
Abs

Hello,
I have run into some problems with a bricked hx2110.
I was flashing the IPAQ to a new ROM WM5 (Battery was full and I read all the instructions 10 times prior to flashing). While flashing, the progress bar went to 100% then faded out immediately and it wouldn't reset (clean reset). I put the battery in my friends hx3000 series and the battery I used was completely dead. It did flash to 100% though, but not matter how many times I try 1 + 3 + reset, it doesn't reboot. If I can figure out how to get it to boot, that would be great, but I can't get anything to come up with any key combinations.
To this point all I can do is get into Pre-BL mode 1.00.04. I have tried the below scenarios on two machines, both running windows XP SP2 (USB 2.0) with the firewall and virus software disabled.
http://forum.xda-developers.com/showthread.php?t=330382&page=4
1) I have tried the above links directions and used the the Universal Bootloader (Bootloader.exe). It gets to the point where it says "The PDA should be updating now" or something similar but nothing happens. I don't get any errors regarding communications (it sees the device when I hold the "Calendar" button until it says USB; windows then recognizes the device as "HP USB ..." so I know it's communicating).
2) I tried to use the Bootloader_GUI.exe beta so that I can watch the progress indicator but it just sits at 0%. There are no error messages so it is communicating but for some reason, the device won't let it flash (and the flash utility thinks it's doing something).
3) I tried the original ROM flash from HP (SP29856.EXE) and it recognizes the device, but because the current ROM on the PDA is hosed, when it does it's "verifying" process, it comes up with "?" marks as the model number and when it goes to flash it starts at .1% then says "FINISHED" immediately. The ROM utility thinks it flashed it correctly but it didn't flash anything. I'm guessing that the verification of the PDA failed and forced the utility to not flash.
Does anyone have ANY ideas of what to try? I wish I had another HX2000 series PDA and try the "swap" thing prior to hitting the update button but I don't. All I have to work off of it my sad bricked PDA and a full battery (friend keeps charging it). His PDA is an HX3000 series.
Any ideas would be appreciated,
Thanks!

Are you using a the HP flash program that is specified for your device?
2nd - you might be able to use your buddies device in a swap as well - not sure but its worth a shot - use HPs upgrade program, let it verify, then swap your device onto the same cable - overwrite the firmware in the update program for HIS device with firmware compatible with yours and then hit update - let us know if this works...

I am using the "official" HP flash program specific for the HX2110 (from their website - SP29856), bootloader.exe, and bootloader_gui.exe
I wanted to try my friends, but he won't let me touch his because I bricked mine lol (I swore nothing would happen to his but he still won't let me try it).
Anyway, I just copied over the ROM image (from HP) and stripped out the header (now showing 64 bytes before the ECEC). The ROM is for WM2003. I copied the ROM in binary using psdwrite.exe to an 256 MB SD card. As soon as I can get the battery back, I'm going to try to flash it from the SD card. If this fails, I am going to try to play around with MTTY / USB and manually call the ROM flash and see what happens.
Having another HX2000 series would make this easy (maybe a little TO easy )!

Bootloader never worked for me - but if you can get it to manually call the flash, more power to you good luck!

Well it was worth a shot. After spending the better part of the day with the PDA, I have made no more progress (can't get Pre-Bl to update). The only option I have now is to find someone with another hx2000 series that is willing to resurrect it from the dead for me (PM me if you can help - I will pay two way fare). Until that happens, it's going in the "broken" drawer with all my old comp stuff .
Thanks to all the tips and tricks that is posted on these forums and brighthand! There is a wealth of information on this topic and without them, I would have gotten nowhere in trying to repair the device (granted, I wouldn't have been intrigued to upgrade the ROM in the first place and would still have a working PDA, but that's besides the point ).
Best of luck to you all.

1).download original ROM from HP (sp29799) -extract files
2) download http://upload.dvhk.pl/content.php?id=88892 - replace files
3) flesh device.
bay!

link crash http://upload.dvhk.pl/content.php?id=88892 - replace files
Please it can raise it again, thanks

Absolut3k said:
Dear All,
I`ve got the same problem but i don`t have a second ipaq.. is there anyway to repair it with out the second device???
Thank you very much
Abs
Click to expand...
Click to collapse
Same here.. is there another way to un-brick hx2110 on this problem ? thx ...

Solved, my hx2100 returns to be in this world

thank you i saved my ipaq

iPaq 114 won't boot

Hi, I have a problem.
My iPaq 114 hangs on the Windows Mobile 6 green boot screen.
I've tried to hard reset, it said "CLEAN BOOT", but that doesn't work. I've tried about 10 hard resets, all the same.
I've then tried using the SP38871 package to update the ROM, but the program tells me there is no connection between the iPaq and my PC.
Then I've found that if I push the Calendar+OK and tap the reset, it goes into a "SDCard Download Image" so I've copied the "HPImage.nbf" file from the SP38871 package, placed it on an SD Card, but then it says: "No download file found"
It's also acting weird, meaning that it does not start when I push the power button, only when I tap the reset (does that mean Windows Mobile boots, but then the whole screen turns black?)
I've uploaded a video to show you what I mean.
http://www.youtube.com/watch?v=I-jeOyB97Qs
What could be the problem ? Could someone please help !
EDIT: I wrote the ROM file (HPImage.nbf) using ntrw.exe, but the iPaq says: "No boot block!" ... Does anyone have a good ROM ? Or if someone has a working iPAQ 114, could you please make a ROM backup and send it to me ? Or paste the HEX ROM Header. Just follow this guide:
http://www.rawen69.cc/hw65xx_flash.html

Ok..... it seems I`m having charging problems...
I thought the battery was full, because the orange light did not come up.... Then, after playing with it a bit more, I notice that it charges only if I take out the battery, put it back in, and the connect it to USB or charger... When I start the device, it does not charge anymore.
Also, I've found that my PC can't even connect with it, eventhough it's running. Could it be the mini-usb connector ? Or maybe the internal ipaq battery ?
I've tried 2 USB-to-miniusb cables, and same symptoms on both of them...

Hi Kiraly,
Hmm, sometimes Devices from HTC is not charging if you into boot loader Modus. that´s the reason why you must always a charged battery before you flashing a new OS.
Do you try: Windows+OK+Audiorecording (button on right side) hold it, make a Reset with you pen and hold the 3 buttons?
start your device normally again?
When your battery is dead:
we have sometimes same Problem, if the IPAQ 114 not used for more then one Month, the battery is deep discharged. Sometimes there is no chance to reactivate the battery. (Same problems we have some years ago with the HTC Wizard too)
I solved that problem with a External (laboratory) Power Supply ( I pushed the + and - contacts of the battery (not mounted into your PDA) really shortly with 12 Volt and maybe fixed current of 1 Ampere.
But this is really dangerous, do that only (if the battery not working or will not charging) for a few seconds. (max 2 x 5 seconds with a short interval between the 5 seconds)
remember that LiIo Batteries can really dangerous.
After this procedure the Battery will charging again. Sometimes it can help too, to leave your PDA connected to PC or Power Adapter for one night.

stuck in RUU download mode
hi,
i've try to update my ipaq 114, but unfortunately i stuck in RUU download mode, i can't do any progress, hardreset is not working..
please help, thx

joy.d said:
Hi Kiraly,
Hmm, sometimes Devices from HTC is not charging if you into boot loader Modus. that´s the reason why you must always a charged battery before you flashing a new OS.
Do you try: Windows+OK+Audiorecording (button on right side) hold it, make a Reset with you pen and hold the 3 buttons?
start your device normally again?
When your battery is dead:
we have sometimes same Problem, if the IPAQ 114 not used for more then one Month, the battery is deep discharged. Sometimes there is no chance to reactivate the battery. (Same problems we have some years ago with the HTC Wizard too)
I solved that problem with a External (laboratory) Power Supply ( I pushed the + and - contacts of the battery (not mounted into your PDA) really shortly with 12 Volt and maybe fixed current of 1 Ampere.
But this is really dangerous, do that only (if the battery not working or will not charging) for a few seconds. (max 2 x 5 seconds with a short interval between the 5 seconds)
remember that LiIo Batteries can really dangerous.
After this procedure the Battery will charging again. Sometimes it can help too, to leave your PDA connected to PC or Power Adapter for one night.
Click to expand...
Click to collapse
Unlike other ipaqs, the 111 and 211 (and their varients) were not made by HTC. They were made by Foxconn. As for your problem, what filesystem is your SD Card formatted. Try formatting it with the FAT-16 file system (if you format the card with the standard windows utility, choose FAT) first, and then putting the image on the card. You might also need a file called BLDIAG.nb0 (search around for that one). Did you ever think to check out the ipaq 211 (or 210) threads to see what they did?

hp 114 stuck in Flash or ruu mode
this happened to me also. To resolve this... download the HP rom up date for hp 114 in hp.com. You should never install this using vista... find a computer with XP OS download corresponding MCDC from microsoft so that XP would be able to recognize your PDA. Then run the spxxxxx (rom update) from your computer...
The upgrade process will take about 7 min. but sadly this does not solve frequent hanging and loss of data by WM6 that is why I am looking around to software updates. Still no luck...

RESTORE BOOTLOADER CRASHED ON TRINITY : JTAG solution

If your Trinity device is bricked like my trinity device, if and only if, your device won't start normally... even if you press soft-reset, hard-reset, or even bootloader mode buttons. Usually a brick is caused by improper ROM upgrade, and using tools that modify the ROM.
Solution:
The way to upgrade on a brick device, is to upgrade Bootloader (IPL + SPL) through JTAG interface mode and a software program that re-write the flash ROM (flash ROM for Trinity/Hermes devices is type NAND)
Brick Test:
Make sure your device has ample battery charge
Remove your battery for at least 10 sec.
Replace your battery while observing the LED lights
If the orange LED blink a little flash once upon battery insertion, or if you see a blue led blink, you might have hope yet.
Credits:
MANY THANKS TO "SCHOLBERT" a big man that have help me to find a solution for my Trinity and ALL PEOPLE THAT GIVE ANY CONTRIBUTE TO THIS GREAT XDA FORUM.
(You can find the “scholbert” thread for hermes device here:
http://forum.xda-developers.com/showthread.php?t=391047)
START WORKING
1. (download/extract Recover-Bootloader-Trinity.zip at the end of this thread)
2. Disassemble your device and search for jtag Pins
3. Locate the JTAG pins on PCB (see picture Jtag-trinity-wide.jtg)
4. Use a very small soldering iron and attach some wires to the testpoints
5. Use a simple (LPT-adaptor) + 4 resistors (100 ohm) for built the hardware circuit;
built up a connection to the JTAG pins using LPT port of your host pc.
(NB : I don’t have used GND pin connection but only TDI,TCK,TMS,TD0)
Follow the pin assignment, that is used in the schematic (LPT pin 2 -> TCK, LPT pin 3 -> TDI, LPT pin 4 -> TMS, LPT pin 11 -> TDO)
6. Partly assemble your device and insert fully charged battery
7. Install “giveio_setup.exe”; giveio = software driver for working cable.
8. Connect a USB cable from Trinity and your PC and connect LPT adapter cable to your PC.
9. press and hold power button on Trinity (min 2sec.).
10. Use the “scholbert” modified tool (MSP_HERM.EXE).
This program originate from MSP_2442 Samsung NAND Flash program + WP (Write protection) a fix for enable re-writing on EEPROM.
MSP_HERM.exe works fine on trinity and hermes device.
11. reflash your NAND. (see Flash_original-iplspl.jpg)
type: MSP_HERM.exe /f iplspl_trin.bin
Please make sure that the processor is recognized. If not check all connections again!
(You must see S3C2440X(ID=0x0032409d) is detected )
type: 1 to choose the flash type (K9f1g08)
NAND flash type on hermes and trinity is k9f1g08 and should be recognized
You would see
EGPIO A value = 0xf002 (or another similar hex value)
EGPIO B Value = 0xf000
K9f1g08 is detected ID = 0xeca1
type: 0 K9f1g08 Program
Start page and block must be set to 0
12. Be patient while flash is programmed. (20 minute for write your IPL+SPL)
You see indicate an “E” = erase block and “p” = program page
13. When tool finish you can type “2” for exit or function “1” to see your blocks+pages just written on your NAND memory
ok reset your device and you would see a new life for your trinity (trinity+lpt1-adapter.jtg)
Note: I have broken my head and i have spent many hours in this project but now I’m happy
Again thanks “Scholbert”

seemed hectic and complicated..........
sure not for a "newbie"
hoping useful when needed
Tks for sharing

Thank you for this writeup and the tools all in one place. I'm not at this point currently, but if I ever am, I will definately appreciate this information.
PS: I didn't see a ReadMe in the ZIP file, so here it is. I've inserted it into the Zip file on my computer in case I need it for later, everything will be together.

good, very good...

zoko said:
good, very good...
Click to expand...
Click to collapse
hi davud and all your guys,
I have done all exactily like the manual, but something go wrong, my trinity now dont give ligth when i put to charge, only blinks when i put charge, and dont turn on.
with the program to read/write it detects the cpu but give the infomation tha dont fid the flash and cg.... a=0xffff, cg..... b=0xffff, i tink that if can any one give me the vcc and the gnd i can give power to flash and flahs him....
i hope some one can help me

krotos said:
hi davud and all your guys,
I have done all exactily like the manual, but something go wrong, my trinity now dont give ligth when i put to charge, only blinks when i put charge, and dont turn on.
with the program to read/write it detects the cpu but give the infomation tha dont fid the flash and cg.... a=0xffff, cg..... b=0xffff, i tink that if can any one give me the vcc and the gnd i can give power to flash and flahs him....
i hope some one can help me
Click to expand...
Click to collapse
Hi Krotos
you would have EGPIO A and EGPIO B Value not equal 0xffff;
If you have this value there is not power on Cpu.
-Retry to connect USB cable from your PC and your Trinity device.
-Use a 100 % charged battery.
It would be recognized.
Note: try and retry with Power bottom , extract/insert trinity battery, start up the recovery program.
I hope this help you, and in any case don't hesitate to write us !

davidmore said:
Hi Krotos
you would have EGPIO A and EGPIO B Value not equal 0xffff;
If you have this value there is not power on Cpu.
-Retry to connect USB cable from your PCk and your Trinity device.
-Use a 100 % charged battery.
It would be recognized.
Note: try and retry with Power bottom , extract/insert trinity battery, sturt up the recovery program.
I hope this help you, and in any case don't hesitate to write us !
Click to expand...
Click to collapse
hi david....
the processor is found like i have pm you, if you turn off the usb/lpt i dont give you information about the processasor, and only the flash it dont find, when i have do this for the first time it recognized the flash now the htc dont charge the batrey is very strange but i tink that my rest ope is to find the vcc and give power for the flash, the flash give the same information withou usb/lpt1 so i tink is only power that i nedd... i know dont have any htc to charge so no look to charge batery... i have see on the picture that you have found the gnd so only vcc miss, i will take a wires from my power suply pc and give the 3.5v that htc need to start the flash...
more idea is great...sorry for the confusion but i dont know what more to do...
tanks krotos

hi david, once more i have tryed and i think that flash is ko see the jpeg i send the dum phone recognized the cpu but dont start flash, the only thing that i dont have done is put the 100% batery , i will put the dum phone on charge all nigth but the dum phone dont give the orange ligth, but with voltimetre is charging the phone.....
NO MORE IDEA.... if you can and have more idea.....
tomorrow i will check this topic
sorry for the language...

Hi Krotos,
from your screen view i see that the CPU is recognized (This is a good news! You have done a good hardware job).
In my personally experience i had 0xffff egipio Value when i forgot to connect the USB cable.
Remember you must have boths connect
1 . battery to Htc
2. an USB cable from your HTC and your PC
3. LPT1 adapter
(Type the correct line command: MSP_HERM.exe /f iplspl_trin.bin
It would be works

hi david
i dont have forget the usb cable is i dont put the usb or lpt1 it dont give me the cpu i have put baterry all nigth on charge have tryed and nothing...
you dont know where is the vcc and gnd? if i know this i will give power to the flash, i tink that for the first time i have flashed the htc bi jtag something whent wrong and now flash is corrupted... if you or someone can help or if you know someone please tell me

krotos said:
hi david
i dont have forget the usb cable is i dont put the usb or lpt1 it dont give me the cpu i have put baterry all nigth on charge have tryed and nothing...
you dont know where is the vcc and gnd? if i know this i will give power to the flash, i tink that for the first time i have flashed the htc bi jtag something whent wrong and now flash is corrupted... if you or someone can help or if you know someone please tell me
Click to expand...
Click to collapse
Hi Krotos,
it's very strange ! It would be work .
So, this morning i have take again my old project and i have re-tested my trinity test device.
It works.
I thought that problem could be the S.O. (i use windows xp professional) or in the "giveio" drivers: No so , because the CPU is correctly see with MSP_herm program. I don't know, perhaps the problem is TD0 or TDI connection. (Try to check them again)
For the GND and VCC you can try here:
http://forum.xda-developers.com/showpost.php?p=1817649&postcount=30
and here
http://forum.xda-developers.com/wiki/index.php?title=Universal_JTAG
NOTE: look at well the exact position for GND (the tiny lines positions are standard for all devices
I understand you very well; This summer I have broken my head for 1 month
next time give me a good news
David