Develop Bugs

Qtek 9090 Dead - Update not 100%, no reaction, no bootloader

Hey guys,
I've searched the forum for like 5 hours or so
to find a thread that could help me solve this solution...
I've tried everything that had something to do with "dead"
in the BlueAngel and Blueangel Update etc. section
What it does:
- The screen stays black
- If I try to charge, the Red 'Charging' LED doesn't become red
unless I take the battery out of the Qtek and charge..
Then it gets red (WEIRD)
- No connection with activesync or rom update utilities
What happened:
- Rom update stopped after a few percentages...
If i try to get a new rom in it with or without cradle
with the following rom update utilities:
- BaUpgradeUt.exe:
then I get a Connection Error (101) when I try to update
- MaUpgradeUt_noID.exe:
ERROR 150: ROM UPGRADE UTILITY ERROR
(Rom Utility not designed for this device)
or "Finished" immediately (but it's not finished)
(Depends on the rom I use, and I used like 10 different roms)
Soft reset / Hard reset doesn't work,
I even tried to Hard Reset by holding the
Voice Record button + Power button + Reset button for 2 minutes
(I tried Camera + Power + Reset too) with the battery,
and I tried these without the battery...
No reaction...
If someone can help me, please do...
Thnx in advance

Maybe you can try thingds from this
http://forum.xda-developers.com/viewtopic.php?p=291989#291989

sep said:
Maybe you can try thingds from this
http://forum.xda-developers.com/viewtopic.php?p=291989#291989
Click to expand...
Click to collapse
Nope,
I've tried that too, but I don't get the USB or WCEUSB in mtty...
The COM ports don't react.
I know how to use it, because I used it like 10 times or somethin'
But I think the problem is, that I can't get in the bootloader mode
(or any other mode)... So there's no response from my Angel..
Thanks anyway..

have you tryed to remove battery, leave it without battery fo an hour or two then put the battery back and power on the device ?
this method may boot your device. If it worked go imediately in bot loader mode and reflash your favorite rom
If it does not helps maybe it is hardware problem ... and you should leave your device in service center

Tried this too
Isn't there any solution except for service center?
I want to know how I can solve this problem,
'cause it could happen again when I update the rom later.
And I know I'm not the only one with this problem.
It would help me and a lot of other BlueAngel owners..

Is it possible to make a serial connection with the bottom I/O port and issue the necessary commands with mtty? could be that there is some logic powered on the board but not enough to make the "USB" section powered up.. similar to serial a console cable on network gear etc. OR.. is there any known secrets such as a hardware debug mode initiated with certain pin(s) on the I/O connector.. such as grounding one or two.. any HTC tech documents floating around for troubleshooting?

You are not one with this problem. The same happens with me too.
Let searching for solution together.
If you want you can contact with me by icq: 190812766

i'm gonna kill myself..3 my friends Jasjar plus 1 qtek dead

Please guys..could anybody help me??error 150 rom upgrade utility error
this rom upgrade utility does not design for your device...
I tried everything but i can't make it works...the window is always the same ... :shock: error 150 rom upgrade utility error
this rom upgrade utility does not design for your device...
MaUpgradeUt_noID doesn't work...
PLEASE PLEASE PLEASE...thanks
mik111

Did you tried hard reset it?

First, don't get panic! Well.When I tried to unlock my device and make it Super CID that message appeared in my screen too.I tried anything I was told in this fantastic forum and nothing worked.Finally I was told to reinstalled windows on my PC and...it worked!! I think it's a problem of drivers. If you are desperated try it.
Good luck and be the force with you...

may the force be with you! :lol:
but like alberbrando said, don't panic. panic would only make things worse. try re-installing your windows. Hopefully, that should resolve your problem.

???
gtm55 said:
Did you tried hard reset it?
Click to expand...
Click to collapse
hi guys..i tried to hard reset it but nothing happend..i'm very depressed...how can it be possible??i've already done this operation with this pc..and it worked..is that possible ?drivers?reinstall windows??****..is one of the of the worst boring operations i've ever done..
any other ideas?

http://forum.xda-developers.com/viewtopic.php?t=61002

frz said:
http://forum.xda-developers.com/viewtopic.php?t=61002
Click to expand...
Click to collapse
thanks frz..i've hard resetted...nothing happend...

So do the other thing they told you and reset windows.
Which is worse? a few hours boredom of backups and reinstalls, or spending what. . . 1300. . £2600 on new PDA's for you and your friends?
I know which one I'D pick.

Try
Try with this upgrade Tools
-put nk.nbf file on this folder
-put your device to bootloader mode
-deactive active sync on your computer
-connect to USB
-Run upgrade tools
cheers
indra9110

Right, don't panic, not being able to flash isn't such a big deal.
First, get an official update package for your QTek, and for your friends an I-Mate update package.
Next, hold the power button and the light-button (next to the volume slider), and stick the stylus in the little reset hole in the back. Hold the keys for a little longer, untill you vaguely see "Serial" or "USB" on the bottom part of the screen (put a little light on the screen, as the backlight will not be lit).
At this point make sure it's connected to your PC through the USB cable.
Right-click the MS ActiveSync icon (on your PC) and choose connection settings, make sure "Allow USB Connections" is unticked.
Next run the update utility, and everything should be fine again
If this doesn't help, ask again and state clearly that you've tried this already.

TheBlasphemer said:
Right, don't panic, not being able to flash isn't such a big deal.
First, get an official update package for your QTek, and for your friends an I-Mate update package.
Next, hold the power button and the light-button (next to the volume slider), and stick the stylus in the little reset hole in the back. Hold the keys for a little longer, untill you vaguely see "Serial" or "USB" on the bottom part of the screen (put a little light on the screen, as the backlight will not be lit).
At this point make sure it's connected to your PC through the USB cable.
Right-click the MS ActiveSync icon (on your PC) and choose connection settings, make sure "Allow USB Connections" is unticked.
Next run the update utility, and everything should be fine again
If this doesn't help, ask again and state clearly that you've tried this already.
Click to expand...
Click to collapse
Thanks Blasphemer but i've done that 2000 times with no success at all...i think that entirely rebuild the pc is my last chance... I don't wanna think at what will happen when the same old window will came out...I' m preparing my gun... :shock:

b4 attempting to flash
b4 attempting to flash,
chk if the 3 steps with mtty work,
if u don't get any error,
plz get ur battrey charged fully from a friend.
then attempt a flash by downloading a different rom from the one u r presently using
disable ur pc firewall
also disable ur anti virus [dont know if this is really required...but i read it in quite a few forums & it worked for me...]
flash only the rom
no extended rom or radio
use the MaUpgradeUt_noID
hopefully this should sort out ur problem....
i know coz i had the same problem....
frz

Another suggestion....
before making any other test, if it's possible, try on another PC, using a fresh rom (not the same used...) .... can be a PC problem, so test the procedure on another host ....

... sorry, again...
have you checked the bootloader version on the devices ? ... verify it before any other tentative ....

help please

my xdalls is dead ,i cannot hard or soft reset it,an orange light comes on when i put it in the cradle,the screen is black and says serial at the top and v 2.08 at the bottom ,could someone help me please ,i have read as much as i can but nothing seems to work tia

Use the SEARCH engine...there are several other posts like yours!

thanks
thanks for your time,it would be nice if you advised me what to search for ?among the many posts,after several diferent searches i am still empty handed ,being a newbie simply suggesting to search wasnt very helpful,thanks anyway

Try here to start:-
http://wiki.xda-developers.com/index.php?pagename=BlueangelFAQ
That page is full of links to help you out.
And then try here:-
http://wiki.xda-developers.com/index.php?pagename=BA_GettingStarted
If you don't understand it don't do it but its pretty straight forward.
People will help if you try things from there and then explain what is happening.

thanks for your help but nothing works
thank you so much for your reply,at least you have tried to adress my problem rather than just telling me to search (which i have already done)
I have previously checked out the posts you directed me to and either i am stupid and dont understand or my problem is different?Anyway what i see my problema as being is that i cannot perform a hard or soft reset by the usual methods ,also active sync dosnt pick up my device so i cannot install any operating system including my original version,i am trying not to believe that i have ruined my device because as a disabled pensioner i rely so much on it and cannot afford to replace it,i have spent hours aquiering the software that i need to help me with my disability and time spent in hospitalsd and waiting rooms,once again thank you for giving me some hope and i would appreciate any further advice

samuraijack said:
thank you so much for your reply,at least you have tried to adress my problem rather than just telling me to search (which i have already done)
I have previously checked out the posts you directed me to and either i am stupid and dont understand or my problem is different?Anyway what i see my problema as being is that i cannot perform a hard or soft reset by the usual methods ,also active sync dosnt pick up my device so i cannot install any operating system including my original version,i am trying not to believe that i have ruined my device because as a disabled pensioner i rely so much on it and cannot afford to replace it,i have spent hours aquiering the software that i need to help me with my disability and time spent in hospitalsd and waiting rooms,once again thank you for giving me some hope and i would appreciate any further advice
Click to expand...
Click to collapse
Unfortunately i do not have a blue angel so my attempts to help are limited but what i would suggest is to fully charge the pda overnight and then remove the battery for ten-twenty mins.
Then try and put it in bootloader mode (after you have reinserted the battery and turned it on).
If you can get this far attatch it to your usb (let any drivers install on their own on pc) and flash the same rom the handset came with.
Hope it helps

actually you are "IN" the bootloader mode... it's the UI for flashing.
Serial... means your USB cable isnt detecting any PC connection.
Orange led means you're phone is charging, that's a good sign.
try charging it for a long time and wait if it becomes green.
then if and when your battery is full...
take your battery out for at least 30-40 mins,
if your backup battery is old... and you know how fast it could drain out
you can use that time instead of the 30-40 mins...
put the battery back...
press and hold the record button + the power button...
now stick the reset.
use a separate synch cable.
then flash your phone again.
if that doesnt work...
search for MTTY...
i dont know the particulars but i think you'll find it somehow
Good luck!

1. Download mtty v1.42 from http://files.pdamobiz.com/ROMs/XDA/mtty1.42.rar
2. Stop ActiveSync, by Task Manager (press Ctrl + Alt + Delete) kill two processes rapimgr.exe and wcescomm.exe
3. put your device into Bootloader Mode by pressing Power + Record Button and Soft Reset.
4. Run mtty (from downloaded) Choose WCEUSBSH001 (If you only see COM 1 and COM 2, try unplugging the USB and replugging it)
5. type "set 14 0" without the quotes to tell bootloader to boot the OS after reset.
6. type "task 28" to get your device formatted (only do this is if you dont mind losing all data on the BA)
7. type "task 0" to ask your device reboot
8. take the device out of the cradle, and manually reset it if it does not do that already.
good luck.

Thanks ,but no Luck
Thanks for your reply,but i cannot Choose WCEUSBSH001 when Run mtty.exe,i can choose Com 3 but when i type in your instructions it tells me to "Please input command name in menu Auto first" ARRGGGHHH! i am going crazt,but i realy appreciate yout time and effprt to my problem,it is wonderful to have some hope of getting it up and running as i am so lost without it,once again any help or suggestions appreciated

did you kill both process in task manager?
Have you tried to unplug the device wait ten seconds and then plug it back in?

RE:more thanks
i dont find the rapimgr.exe process running ,could that be the problem? thanks again ,really appreciate your time and efforts

kinda new to this myself mate but had a similar problem recently.
firstly, it sounds like your OS has gone....the screen you can see basically means there is nothing to 'boot' to.
'serial' should change to 'usb' once plugged into the pc before you can start active sync and reloading an OS.
try, if possible, a different usb port if that fails is there any chance you could borrow another cradle to check that the usb side is ok?.
another thing i did not see mentioned (may have missed it), if you push power + soft reset together and as soon as you see the boot loader press record + camera at the same time, if this works it will show 3 options, first one should remain 'no' the next 2 should be changed to 'yes', (record moves down the options, camera changes the setting) then press the 'mail' button.
this should clear the BA (losing any saved data etc) but might 'wake it up' so the pc will recognise it again and allow you to reload.
if it is showing 'serial' and charging then i doubt it is broken beyond repair, just one of those annoying problems that comes with technology.
i upgraded to WM6 with no problem, it was as i tried to downgrade back to 2003 i got my problems, it appeared as if i had wrecked my BA but re-read all help/instructions a few times and managed to get it sorted, dont give up hope, just keep going over it.....i am sure you will get there, good luck.

Given up
thanks for all your help ,after trying so many combinations ,i have given upo and sent it in to be repaired,i was wondering however if it is worth upgrading it to 6? and what the correct rom version is ,any help here would be apreciated ,and once again thanks for your time

Pocket Loox N560 stuck on boot screen. Won't start up

Does anybody know if there is a way to boot N560 using SD card? I think I killed my FS with some "rom killer" and all I get now is FS boot screen, no other activities.
Any way to start it from SD card and flash it from there?
Perhaps any other way to bring it back to life?

i have the same problem
is there anybody for help???
SOS please

Eenigmaa said:
Does anybody know if there is a way to boot N560 using SD card? I think I killed my FS with some "rom killer" and all I get now is FS boot screen, no other activities.
Any way to start it from SD card and flash it from there?
Perhaps any other way to bring it back to life?
Click to expand...
Click to collapse
You cannot burn the ROM from an SD card.
If the device has had the anti-theft password set at some stage then you cannot reburn the ROM! This might be the problem?
A hard reset on the N560 followed by running the Loox burn program on a PC with ActiveSync connection to the N560 cradle is the only answer i.e. a normal ROM burn.

fingerstoo said:
You cannot burn the ROM from an SD card.
If the device has had the anti-theft password set at some stage then you cannot reburn the ROM! This might be the problem?
A hard reset on the N560 followed by running the Loox burn program on a PC with ActiveSync connection to the N560 cradle is the only answer i.e. a normal ROM burn.
Click to expand...
Click to collapse
Theft protection is not a problem here. It was wrong ROM and now it is stuck on boot screen, active sync does not see it at all, maybe there is a trick to somehow anable burn, flash, service mode on it? So far nothing helps....

Eenigmaa said:
Theft protection is not a problem here. It was wrong ROM and now it is stuck on boot screen, active sync does not see it at all, maybe there is a trick to somehow anable burn, flash, service mode on it? So far nothing helps....
Click to expand...
Click to collapse
read, and pay attention here:
[email protected]@p://a.mod-site.net/gb/u/newplow-1.html
POST 203.
Edit/Delete Message

vladtapes said:
read, and pay attention here:
[email protected]@p://a.mod-site.net/gb/u/newplow-1.html
POST 203.
Edit/Delete Message
Click to expand...
Click to collapse
GREAT!!!!
Thanks ever so much! You are real HELP!!!!
You should close process "wcescomm.exe" on PC in task manager. Then hold button record, power and puch reset after that you will come in boot loader. Run the program mtty.1.42 and select usb connect. If You will see the any error just start again mtty. Put command l c:\os_213u.nbf (You should put correct flash file in c:\ or use correct path to os_213u.nbf, l - like L but small). When it will done You should start PocketLOOX5xxFlashTool.exe and flash you PDA.
Click to expand...
Click to collapse

Eenigmaa said:
GREAT!!!!
Thanks ever so much! You are real HELP!!!!
Click to expand...
Click to collapse
do you confirm the method is fully functional?
I made a backup of my german original rom, if i have problems i want to restore it...
have you got a backup of your old wm5?
thanks

Yes it is working! Even if error comes at the end, shut the appie and use FS update tool to finish it up! All perfect!
Google for WM5, it is somwhere out there!

Eenigmaa said:
Yes it is working! Even if error comes at the end, shut the appie and use FS update tool to finish it up! All perfect!
Google for WM5, it is somwhere out there!
Click to expand...
Click to collapse
could you please p.m. to me the link of wm5 other language?
If you refer 4pda...it can't be downloaded, i don't know russian, i registered, but always cannot download...
if you have other link...pls send me...

vladtapes said:
could you please p.m. to me the link of wm5 other language?
If you refer 4pda...it can't be downloaded, i don't know russian, i registered, but always cannot download...
if you have other link...pls send me...
Click to expand...
Click to collapse
You can if you use an translator like www.windowslivetranslator.com or translate.google.com
then it is pretty easy.

I've resolved...
Fully functional WM6.0 newplowe in English...
now I'm searching for editing it in Italian/French but I need to edit the rom part of the XIP (just that).
For doing that, I need to open decrypt the file .nbh file (don't really know howto, and newplow doesn't answer about that... ).

Hi everybody, I need your help. I spent 2 hours to read several posts about N560 brick recover, and I still can't figure how to do it.
I flashed the N560 with the WM 6.1 and then I tried to flash the backup Rom Image ... which failed. Now is stucked in the climbing image ... and is not reacting to nothing. I didn't try the mitty sol because I don't have a clear ideea about using it, I am still a newbie ...
Please, I am begging for help if you can , thanks

rcretu said:
Hi everybody, I need your help. I spent 2 hours to read several posts about N560 brick recover, and I still can't figure how to do it.
I flashed the N560 with the WM 6.1 and then I tried to flash the backup Rom Image ... which failed. Now is stucked in the climbing image ... and is not reacting to nothing. I didn't try the mitty sol because I don't have a clear ideea about using it, I am still a newbie ...
Please, I am begging for help if you can , thanks
Click to expand...
Click to collapse
Try this?
Take the N560 off the cradle. Remove the battery for at least 30 seconds. Reinsert battery and back cover. Do not worry if the screen shows the dolphins again. Do a full hard reset to get back to factory setting i.e Simultaneously press and hold the Suspend/Resume button (1) and the Calendar application button (2). Briefly press the stylus tip into the soft reset opening (3). Continue to hold down the Suspend/Resume button and the Calendar application button for a few seconds. The reset can take a few minutes. At the end an acoustic signal sounds. Please follow the further instructions on the display.
A hard reset should put the device back to the existing (last burned ROM) and you can try the burn again.
You probably do not know why the burn originally failed. The most common reason is some interrupt of the processor (internet access, switch of all internet access) but more likely something is polling the USB port, which might be shared in the PC. My external USB TV tuner constantly polls the USB port and interrupts any transfers on other ports! I suggest that you disconnect all other USB devices and make sure that your N560 cradle is connected to a USB port directly on the motherboard of the PC (not a USB hub or expansion card with multiple USB ports).
Hope this helps.

N560 - still stucked in the climbers bagground after WM 6.1 flash
fingerstoo said:
Try this?
Take the N560 off the cradle. Remove the battery for at least 30 seconds. Reinsert battery and back cover. Do not worry if the screen shows the dolphins again. Do a full hard reset to get back to factory setting i.e Simultaneously press and hold the Suspend/Resume button (1) and the Calendar application button (2). Briefly press the stylus tip into the soft reset opening (3). Continue to hold down the Suspend/Resume button and the Calendar application button for a few seconds. The reset can take a few minutes. At the end an acoustic signal sounds. Please follow the further instructions on the display.
A hard reset should put the device back to the existing (last burned ROM) and you can try the burn again again.
You probably do not know why the burn originally failed. The most common reason is some interrupt of the processor (internet access, switch of all internet access) but more likely something is polling the USB port, which might be shared in the PC. My external USB TV tuner constantly polls the USB port and interrupts any transfers on other ports! I suggest that you disconnect all other USB devices and make sure that your N560 cradle is connected to a USB port directly on the motherboard of the PC (not a USB hub or expansion card with multiple USB ports).
Hope this helps.
Click to expand...
Click to collapse
Hi and thanks a lot for your post ... I tried several times this procedure ... I see no change for the hard reset .. No dolphins image at all ... I would say whatever I do it doesn't affect it. No sound, no other signs ... same climbing image.... Please keep remember other solution, It should be one ... thank you again ...

rcretu said:
Hi and thanks a lot for your post ... I tried several times this procedure ... I see no change for the hard reset .. No dolphins image at all ... I would say whatever I do it doesn't affect it. No sound, no other signs ... same climbing image.... Please keep remember other solution, It should be one ... thank you again ...
Click to expand...
Click to collapse
THANKS FOR HELP, I didn't made correctly the the procedure ... now all it's Fine ... really appreciate your help ... saved my precious loox ...

rcretu said:
THANKS FOR HELP, I didn't made correctly the the procedure ... now all it's Fine ... really appreciate your help ... saved my precious loox ...
Click to expand...
Click to collapse
PHEW! Thank goodness. I suspect you did not do the hard reset correctly at first. But I agree about the Loox being precious! I look after mine very carefully! Glad I could help you. My pleasure....

My fs560 is brikked!!!!
It remains to climbing people...
I can enter to bootloader (dolphins) but i cannot update to Windows mobile 6.1 Classic ver. 063.07
I need your HELP!!
I tried to use mtty and i can arrive to:
Image Download Finish
OEMFlashWrite(A0000000h,8C200000h,0236002Ah)
Download Fails !!!
OEMFlashWrite error(12)
Error : DownloadImage return error (code = 0xFFFFFFFF)
but then I cannot initialize normal update, it remains to dolphins with the blue bar fullfilled by precedent mtty...
the PocketLOOXN560FlashTool.exe can't find the device...
Can someone explain me the CORRECT method after mtty?
PLEASEE!!!

vladtapes said:
My fs560 is brikked!!!!
It remains to climbing people...
I can enter to bootloader (dolphins) but i cannot update to Windows mobile 6.1 Classic ver. 063.07
I need your HELP!!
I tried to use mtty and i can arrive to:
Image Download Finish
OEMFlashWrite(A0000000h,8C200000h,0236002Ah)
Download Fails !!!
OEMFlashWrite error(12)
Error : DownloadImage return error (code = 0xFFFFFFFF)
but then I cannot initialize normal update, it remains to dolphins with the blue bar fullfilled by precedent mtty...
the PocketLOOXN560FlashTool.exe can't find the device...
Can someone explain me the CORRECT method after mtty?
PLEASEE!!!
Click to expand...
Click to collapse
I think you have received a reply from Newplow on his guestbook....

Hi
I tried to upgrade to 128mb but after restart I see only climbing. I tried everything here but on dolphins afterr line is blue it is finished. that I am unpluging device. starting looxflastool for 560 and first is trying to connect by active sync and that when no connection made I see dolphins on left screen of flash tool window. than I am pluging again and after couple secs I see that: Error"The language in this Flash Image update (ENGLISH) differs from that on your device. I tried to change rom on every language but not working as well. PLEASE HELP!!
if that helps than i will add than on top when delfins i see on 560 is two lines. first is typed 2.14.G4 on second directly below is 2.15.
and when mtty 1.42 finishing flashing i see following:
Image Download Finish
OEMFlashWrite(A0000000h,8C200000h,0224002Ah)
Download Fails !!!
OEMFlashWrite error(12)
Error : DownloadImage return error (code = 0xFFFFFFFF)
I've done already procedure You've mentioned here with taking of the battery for at least 30 secs with hard reset afterwards but it is still climibing screen. Can U manage this as well???
THX

The most common error with the procedure is NOT making a proper or true hard reset, or back to factory settings reset. If you do it wrong, you will only achieve a soft reset, the same as you get if you just put the stylus in the reset hole in the base of the N560.
The correct procedure is to hold Power/Resume/Suspend button (on/off button) and the Calendar button simultaneously. Keep holding them and with the other hand press in the reset hole with the stylus. The screen should blank out. KEEP holding the other two buttons all this time, and release the stylus. KEEP holding those two buttons until the screen display returns, only then release them.
This should allow another burn.
I hope this is the problem. It has happened to me and others, so I think I am right. But if this fails, you may need another approach.

[Q] My S8530 is Bricked

I have made a really stupid mistake
i have changed my product code to 8600 a few days ago
and really forgot about it
http://forum.xda-developers.com/showthread.php?t=1333956&highlight=code
i was trying to flash my phone as I did many times before
using 1.2 ver
when I got to dbl.mbn - boot files
muliloader (ver 5.65) got an error - security fail
and then nothing
black screen
no download mode - in any condition
no battery icon - when the cell is connected to power adapter
no response from usb when I connect to pc
kies of course cant see my cell
only black screen
any advice ?
10x in advance

no download mode - in any condition
Click to expand...
Click to collapse
Before you are sure... Bootloader is dead...
1.
Remove battery for few minutes
2.
Be 100 % sure your battery is NOT empty...
Good luck.
Btw.:
I saw this error often in posts from other users... maybe this has nothing to do with Product Code...
Often between bada 1.x and 2.0 change or Bootloader change general...
Best Regards

yes donot worry
just remove the battery and put it back and try to go to download mode directly
best regards

its verry problematique if you dont have another battery cause now you cant recharge it.
Then there's trick what you can do.
Im serious i do it but be carrefull..
We know wave recharge white usb and usb its 5volt then try to find other recharge you dont use it and cut the positive and negative lead then look on battery put in to recharge it directly 1 or 2 min then you can flash the important bootfiles to rc1 first
Send from Wave S8530

Thank you all for support
but the problem is not in the battery
I never flash my cell - if I dont have at least 80% power of the battery
I think it is something with the change of the product code ( I have changed to 8600)
and error of security I got - in the dbl.mbn
If you dont have any magic trick to offer , then my phone is dead (Jtag or riff box at least )
me any my curiosity

if you arre good at soldering and such you could try the
unbrickablemod

if the phone seal still intact,
go to samsung service center.
they will give you a new phone.