Friends,I recently flashed my wave 2 s8530 to bada 2 and yesterday when i tried to flash it june update indian firmware(s8530 DDKF1) ,the flashing failed midway.I was getting rsrc1 erase error.I tried to flash it again still d error didn't go.After some time my phone showed "SOFTWARE UPDATE FAILED" error.Now i can't even enter the download mode.When i try,the download mode comes and after 5 sec the screen becomes blank or d software update error shoots up...I dont know what to do and I dont want to give it to the service center because i need the cell in working condition by sunday...Please help.
Try these options:
1. Make sure all necessary drivers are installed.
2. USe the correct version of multiloader to flash (flashing back from a different bada version usually has problems with multiloader v5.62 e.g. erase error).
3. Remove battery from phone for a mimumum of 10 minutes. Then insert battery again. Please borrow a fully charged battery from a friend (as yours obviously cannot be charged now).
4. Try flashing again.
Best of luck.
Related
:roll:
i reaaly feel depressed .. & that is coz when i was tring to upgrade my T_Mobile Radio to RU 6.24.00
that i downLoaded from http://www.romanweb.com/yorch/
my mobile gave me the messge of that the upgrade failed ...
keeping repeating restarting ..upgrading process progress for several times ...then i ting i did restart or something like that after that I think my device Died no longer working all what i could see is T)mobile start screen with the ROM vervion RT Lower Courner U above it & some letter above them without vervions #s!!! !!!.
I did reset+ON/OFF Botton pressing ... got into the WALLBAY Bootloader V5.15. then .............................. WAIT...
then i resseved the messege GSM ERROR.
I restarted same as before +on/off .
Recieved same message then Pressed RT Upper Botton got into FLASH TOOLS selected GSM ROM TO SD got the messege
SD Backup
==============
Please
connect rs232
and run PC Monitor
Now
in your sitle this messege is followed by
SD BACKUP
=============
Please
connect rs232
and run
PC Monitor
Now
We're not yet sure how to use this to dump the GSM ROM.
..... End.
Now ,,, what sould i do to recover my T-Mobile ....
GSM Error, 1% failed, and battery not charge
That was what happen on my XDA too. I've been upgrade, downgrade both OS and RS roms with my XDA for about 9 mos without any trouble until last week when I tried to upgrade RS from ATT A20.10 to TMO 6.24.01, the upgrade failed and now I am stuck with 1% failed problem. Worse, the battery is not charged any more causes any further upgrade fail. I still can upgrade/downgrade the OS rom but do not know how to fix the Radio stack.
I have tried virtually all suggestion on this forum: the 4 RS files upgrade, SD nb1, nbf upgrade, repair.zip, Programme A, programme B, different OS and RS roms upgrade/downgrade. None worked.
I even opened the XDA and connected wires. Still not working.
Hi, I have a problem with my defy and I really short to deal with that. First my defy stopped on red M logo and done proceed to system start. So I go to service menu, set clear cache- cache were cleared for 30mins so I take out batery, then I set - format/factory reset. same problem, it goes without end so after batery goes off, I make McGiver style for bring pnone to life and go to boot loader, run firmware flash over RSD lite and wait......after that RSD give me this message - Phone [0000] Error verifiing code group 33 Checksums. File:0x8BAC,Phone:0x4805 . RSD do nothing, on phone were instaling. after our when I suppose this is and I take out batery from phone and try run it. Every time start boot loader with message :
Code Corrupt
Battery OK
OK to Program
Conect USB
Data Cable
I cant launch android recovery, and If i flashed firmware again a have the same and. Can you please somebody help me with that??
Thanks,
ps. sorry for my english I think is not perfect
new thing, new error mesage from RSD. he pass Checksums errors, than give me message - restarting device ( that is not happend, device were still on), afted while there is new message : Failed flashing proces. Failed plashing proces. phone [0000] Error geting subscriber unit checksum. Device API error: 0xe003003F Command : (RQRCS 0xe403203f); phone conected
result FAIL
I am really desperate.. anyone have experience with this??
Thanks for any advice.
NoDi
As I see probably nobody had this issue like I had. Tomorrow I try bring phone to seller (Vodafone), and than I have to pray for reflashing it from them. Anywhere I will post result from them after I get some, If somebody have the same problem in future like I had.
NoDi
Difrent SFB
try usuing difrent sfb f.
have similar problem at some time...
just try using another sfb and do factory reset each time
yea.. some sbf have higher or lower on img version which might prevent your phone from fully flashed.
I tried various different FW from here. Everytime the same results. Today I was bring phone to Vodafone, I wonder on verdict
you said you tried all firmware versions, can you try diffrent RSD Lite version, may be RSD lite having problem. I am using " RSD Lite 4.9.msi ".
so phone is back. In report from service were Changed bad SWAP module. In used parts were 1pcs of RF board. Anyway I brought phone back to Vodafone because he cant sign in other than 3G network, and many places in our country are sill only 2G.
Hi,
I have a Samsung Galaxy S Plus here which is almost brand new and has only been used for some phone/texts/emails so far.
I connected it to a PC running Samsung Kies and it told me there was a firmware update available for this phone, so i clicked ok and had it install.
During the installation, at 22%, everything freezes and locks up, it remained at 22% for 45 minutes until (after some googling) i was recommended to just turn it off / reboot it.
After rebooting, i constantly get this icon on the screen :
Copy & paste the following in a web browser (as I'm not allowed to place a link or picture apparently)... : img267.imageshack.us/img267/930/fotofg.jpg
I tried removing the battery for 10 seconds and then boot it up again - same screen.
And it doesn't matter if its connected to the PC or not, its always that screen.
And when it IS connected to the pc, samsung Kies shows the 'connecting' screen but it never actually connects.
What do I do ?
How is it possible that someone's phone gets locked/frozen for simply trying to update ?!
orangewall said:
Hi,
I have a Samsung Galaxy S Plus here which is almost brand new and has only been used for some phone/texts/emails so far.
I connected it to a PC running Samsung Kies and it told me there was a firmware update available for this phone, so i clicked ok and had it install.
During the installation, at 22%, everything freezes and locks up, it remained at 22% for 45 minutes until (after some googling) i was recommended to just turn it off / reboot it.
After rebooting, i constantly get this icon on the screen :
Copy & paste the following in a web browser (as I'm not allowed to place a link or picture apparently)... : img267.imageshack.us/img267/930/fotofg.jpg
I tried removing the battery for 10 seconds and then boot it up again - same screen.
And it doesn't matter if its connected to the PC or not, its always that screen.
And when it IS connected to the pc, samsung Kies shows the 'connecting' screen but it never actually connects.
What do I do ?
How is it possible that someone's phone gets locked/frozen for simply trying to update ?!
Click to expand...
Click to collapse
have the same problem ... did u solving ?
XXX.hard-reset.com/samsung-i9000-galaxy-s-hard-reset.html
Copy and paste into address bar not allowed to post links. Substitute xxx for www
Custom solution
Hello,
It's a big problem, but maybe can you blame samsung? However, I don't know if you have CMW, but try to boot that and than install custom rom (a zip rom). After that you can install original firmware.
If that doesn't work find a rom that works with odin, boot in download mode and install that rom, after that install original firmware.
Similar thing append to me but wile using odin i got the same screen.
What i did was connect it gain to the pc, odin detected it and was able to flash the rom.
It was pretty scary i assure you.
My advise is if the phone is brand new take it to your dealer a let them sort this out as it was not your fault at all.
If it's a brand new phone I'd use Samsung's warranty or maybe even return it.
Hello everyone,
i bought the SM-P607T during my deployment in Afghanistan over Ebay USA . Spending my time there i tested the device and installed all updates etc. Back in Germany just my wife used it. Some weeks ago i noticed that an update to Lollipop should be avaible so i took the device to bring it up to date and i noticed some problems.
(Please note that i am just a noobie to flashing and rooting android and just follow guides to get to my goal.)
1. Device only loading while shut down. (After rooting and installation of TWRP it strangely started to load while on again even on PC USB connection)
2. Its not possible to connect the device with any PC.
3. OTA updates stop at around 27% and fail (KitKat 4.4.4)
[In TWRP shown
"E: Error executing updater binary in zip /data/fota/update.zip
E: Error installing zip file /data/fota/update.zip"]
Strange enough that the update info shown in android is Chinese Version
Tried to get some support with Samsung Europe but unfortunately they say US device US problem......
So what did i do in the meantime
1. Tried different loading devices frome Samsung and 3rd party companys. No changes.
2. Tried several different data cables to connect to 4 different PC. Even the one wich worked good with my Honor7 or the Galasy S4 mini dont do with the 607
3. My last try to fix this problem was to change the USB charging dock completely. Also didn´t change anything.
4. Now the step where i am currently stuck. I managed to root the device and install TWRP(v2.8.7.0) . Now tried to install Version P607TUVUBOI2 via SD Card.
Just followed diffenrent Guides on youtube and forums but im stuck at this.
Here is the message i got in TWRP recovery:
"Installing /external_sd/1/TMB-P607TUVUBOI2-20510930112901.zip
Checking for MD5 file....
Skipping MD5 check : no MD5 file found
Error flashing /external_sd/1/TMB-P607TUVUBOI2-20510930112901.zip
updating partition details......
Checked the *.zip on my PC there was just this file in: P607TUVUBOI2_P607TTMB1BOI2_P607TUVUBOI2_HOME.tar.md5
Downloaded the file from a different source again with same result
It would be very nice if someone is capable to help me with this and give me a hint what i possibly did wrong (Please do not mention not to buy in the US). For me it doesnt matter if i got a rooted or not routed version to install my main goal is to get rid of 4.4.2 . The problem with the not working USB connection is the biggest show stopper for me.
[email protected] said:
Hello everyone,
i bought the SM-P607T during my deployment in Afghanistan over Ebay USA . Spending my time there i tested the device and installed all updates etc. Back in Germany just my wife used it. Some weeks ago i noticed that an update to Lollipop should be avaible so i took the device to bring it up to date and i noticed some problems.
(Please note that i am just a noobie to flashing and rooting android and just follow guides to get to my goal.)
1. Device only loading while shut down. (After rooting and installation of TWRP it strangely started to load while on again even on PC USB connection)
2. Its not possible to connect the device with any PC.
3. OTA updates stop at around 27% and fail (KitKat 4.4.4)
[In TWRP shown
"E: Error executing updater binary in zip /data/fota/update.zip
E: Error installing zip file /data/fota/update.zip"]
Strange enough that the update info shown in android is Chinese Version
Tried to get some support with Samsung Europe but unfortunately they say US device US problem......
So what did i do in the meantime
1. Tried different loading devices frome Samsung and 3rd party companys. No changes.
2. Tried several different data cables to connect to 4 different PC. Even the one wich worked good with my Honor7 or the Galasy S4 mini dont do with the 607
3. My last try to fix this problem was to change the USB charging dock completely. Also didn´t change anything.
4. Now the step where i am currently stuck. I managed to root the device and install TWRP(v2.8.7.0) . Now tried to install Version P607TUVUBOI2 via SD Card.
Just followed diffenrent Guides on youtube and forums but im stuck at this.
Here is the message i got in TWRP recovery:
"Installing /external_sd/1/TMB-P607TUVUBOI2-20510930112901.zip
Checking for MD5 file....
Skipping MD5 check : no MD5 file found
Error flashing /external_sd/1/TMB-P607TUVUBOI2-20510930112901.zip
updating partition details......
Checked the *.zip on my PC there was just this file in: P607TUVUBOI2_P607TTMB1BOI2_P607TUVUBOI2_HOME.tar.md5
Downloaded the file from a different source again with same result
It would be very nice if someone is capable to help me with this and give me a hint what i possibly did wrong (Please do not mention not to buy in the US). For me it doesnt matter if i got a rooted or not routed version to install my main goal is to get rid of 4.4.2 . The problem with the not working USB connection is the biggest show stopper for me.
Click to expand...
Click to collapse
I really confused about your description? you using twrp to flash a .zip rom? then you mentioned about .md5 rom on your pc? how did you flash? With .md5 rom you need to use Odin to flash. Can you boot into download mode (hold down volume down + Home buttons then press power button)? If you able to boot to download mode, your pc should able to see the device and you would use Odin to flash the .md5 rom from your pc to the device. Also where did you download the .zip rom?
hello guys
i have a j600fn to recover after a failed automatic update (low battery and shut off)
after failed update i tried to manual update via odin to latest oreo rom from sammobile but i have this issue:
- phone changed from single sim to dual sim
- imei changed
- every sim i put in will not connect to network..
i'tried to flash combination and 4 files recovery but no results at all..
can someone help me to recover my phone please?
mastermoon said:
hello guys
i have a j600fn to recover after a failed automatic update (low battery and shut off)
after failed update i tried to manual update via odin to latest oreo rom from sammobile but i have this issue:
- phone changed from single sim to dual sim
- imei changed
- every sim i put in will not connect to network..
i'tried to flash combination and 4 files recovery but no results at all..
can someone help me to recover my phone please?
Click to expand...
Click to collapse
have you already tryed to hold the buttons vol + and vol -
and then insert cable
then start odin ?
let me know if this works for you
PS you need to look up the right type of carrier in my case its PHN
and its the j600fn
if you start the phone like i said above you will see a small text in the upper left corner of you screen
with the right type of J600***** and the right type of rom like i said above it PHN for me
kind regards marthy1992