i tried to set up htc hd rom on my device ( kaiser )
after booting from my device
it work normally till the 1st third on stripe at booting screen
then this message appear
" the update is failed and terminated "
i made restart
but the phone doesn`t work after this
what shall i do
please help me
Have you tried installing a ROM made specifically for the kaiser or do you mean that the phone won't even turn on for you to get to the installation menu? It's not a great idea to install roms designed for other devices, especially one that has no similarity to the kaiser. The roms need a lot of updates before they will work on the kaiser such as kernel modules, drivers etc.
thank you for reply
but the phone doesn`t work at all ablack screen
even not recognized by pc
fayedcoo said:
thank you for reply
but the phone doesn`t work at all ablack screen
even not recognized by pc
Click to expand...
Click to collapse
So when you pull out the battery and put it back in and turn the phone on does it do nothing, no leds, no screen at all? if so there is a few things it could be, either a dead battery which needs charging, sometimes it takes a bit of charging before the phone will come to life again. You could have a shorted pin in the mini-usb socket on the bottom or elsewhere in the phone stopping it from turning on or the phone is bricked completely. What happends if you hold down the camera button whilst pressing the power button to turn the phone on?
i did every thing you imagine but nothing at all
just a black screen
battary is ok.
i did hard rest but nothing .
and the computer don`t recognize it.
i think it`s dead
any body can help me ??????????????
Sounds like the phone is completely bricked, if you tried hard resetting it, pulling the battery, and trying what scoot said to try -- Hold camera button while pressing the power button to boot the phone. When doing that you should get a tri-color screen.
i did this but still not work
what shall i do if it`s completely bricked
fayedcoo said:
i did this but still not work
what shall i do if it`s completely bricked
Click to expand...
Click to collapse
Get your battery charged through a universal charger (which charges battery in its own cradle), put it back into kaiser.
Connect USB cable to PC
Hold Camera button and Insert other end of USB cable into your kaiser.
Go to My Computer Proporeties > Device Manager and see if there is a composite device in the USB Devices drop down list. If there exists, all you have to do is to flash official ROM again.
While you installed an "HD" rom which was intended to run on HTC HD rather than HTC TyTn II, maybe you actually over-written your kaiser's SPL/Radio while doing so.
NEVER EVER FLASH A ROM INTEDED FOR ANOTHER DEVICE THAN THE ONE YOU HAVE
thanks for replay
but i think the problem not the battary because i tried another one 100% WORKING
i rally do what you say but i don`t observed any change
what happen to the device after upgrading with this funcken rom
is the motherboard bricked totally or somthing about the flash ???????????????
i respect your replay
thanxxxxxxx
fayedcoo said:
thanks for replay
but i think the problem not the battary because i tried another one 100% WORKING
i rally do what you say but i don`t observed any change
Click to expand...
Click to collapse
Hold Camera button, plug in USB Cable
If your device gets into three-colour screen, flash the official Windows Mobile from HTC
Related
Of usually i search and search until I find an answer but I have now idea what to do...
-T-Mobile Dash with a Cingular Sim running Kavanna 6.1 (and kavanna has ran fine on it for the most part)
-Phone randomly froze (wouldnt let me type a text msg)
-Powered off
-Went to power it back on and nothing -no lights, no nothing
-Tried the two softkeys and power button for two seconds
-Tried te camera button and power button
-Pulled batter multiple times and pulled all cards from it
-When it is plugged into a wall I dont even get a power charging light....
Any ideas? I cant afford a new phone
[email protected] said:
Of usually i search and search until I find an answer but I have now idea what to do...
-T-Mobile Dash with a Cingular Sim running Kavanna 6.1 (and kavanna has ran fine on it for the most part)
-Phone randomly froze (wouldnt let me type a text msg)
-Powered off
-Went to power it back on and nothing -no lights, no nothing
-Tried the two softkeys and power button for two seconds
-Tried te camera button and power button
-Pulled batter multiple times and pulled all cards from it
-When it is plugged into a wall I dont even get a power charging light....
Any ideas? I cant afford a new phone
Click to expand...
Click to collapse
looks like your battery is gone Try with another battery
woulnt I be able to get some sort of power or light with the batter pulled and it plugged in? cause I dont....
[email protected] said:
woulnt I be able to get some sort of power or light with the batter pulled and it plugged in? cause I dont....
Click to expand...
Click to collapse
Not if your battery is completely waste it. Check if your battery pins in your dash make full contact with your battery, because that can cause a problem (very odd, but it happens). If not, try another battery.
Have you checked your charger, I guess is damaged because if your battery is damaged or if is no battery at all and you connect the charger the led will turn red.
sam happened w me, no solution yet
hate to tell you that you might have bricked your phone,
the same happened to my excalibur, when i tried to flash it -mistakenly- with the wrong rom,
thing is; the rom is controlling the power charging process and the battery support to the device, if something went wrong with the rom for any reason; then no instructions are sent to the battery neither the charger, therefore: no power sign of any in the device.
i couldn't find an answer to fix my dash, but i think the solution is either changing the rom or JTAG-ing it might solve the problem, though i have no tools neither knowledge to do so.
sorry pal, the bright side is: you are a member of (BDC) the Bricked Dash Club
cheers
bootrecord said:
hate to tell you that you might have bricked your phone,
the same happened to my excalibur, when i tried to flash it -mistakenly- with the wrong rom,
thing is; the rom is controlling the power charging process and the battery support to the device, if something went wrong with the rom for any reason; then no instructions are sent to the battery neither the charger, therefore: no power sign of any in the device.
i couldn't find an answer to fix my dash, but i think the solution is either changing the rom or JTAG-ing it might solve the problem, though i have no tools neither knowledge to do so.
sorry pal, the bright side is: you are a member of (BDC) the Bricked Dash Club
cheers
Click to expand...
Click to collapse
With the information provided it hasn't been your same case due that he hasn´t flashed any other rom, so basically he can try another battery and see what happens.
errrrrr
New Battery - Still no lights and using the reset features found in the unbricking tutorial do not work.
Tried using a cable from my comp to give power to phone so it isnt power cable
So what now? I cant even get to a bootloader screen or anything.... I cant afford a new phone ERRR
**Update-
Was plugging in the USB cable and looks like it gets a connection only when it is plugged in a little but this not just at the end that connects to the phone (it happened when the phone was already plugged into the cable and I was plugging it into the comp and vice versa) Um so that is strange - the light does not stay on and when the battery is in the phone I do not get that quick red flash - so it still doesnt work and cant do anything
[email protected] said:
New Battery - Still no lights and using the reset features found in the unbricking tutorial do not work.
Tried using a cable from my comp to give power to phone so it isnt power cable
So what now? I cant even get to a bootloader screen or anything.... I cant afford a new phone ERRR
**Update-
Was plugging in the USB cable and looks like it gets a connection only when it is plugged in a little but this not just at the end that connects to the phone (it happened when the phone was already plugged into the cable and I was plugging it into the comp and vice versa) Um so that is strange - the light does not stay on and when the battery is in the phone I do not get that quick red flash - so it still doesnt work and cant do anything
Click to expand...
Click to collapse
Maybe is your USB port causing the problem.
pls help me ..i lost connection ugrading to a new rom...now my xda exec universal is dea...even cant get into bootloeader..onmy soft reset and when i press the O for factory defoulds .still does nothing just goes to its dark screen
put it in to bootloader and flash a new rom.
universal dead
thanxs for the replay ..the universal dont even gets in bootloader. when i press the 3 keys for geting in the bootloader ,it does not .what else can i do???
Please read the wiki before posting:
http://wiki.xda-developers.com/index.php?pagename=Uni_Stuck_Bootloader
http://wiki.xda-developers.com/index.php?pagename=Uni_Stuck_Bootloader_Serial
I think what dekyprio is saying is that the Uni does nothing while powered on. I have the same issue on my side, so for now my Uni is waiting in a box for the process to bring it back to life :-(
Any help would be appreciate.
Regards
hey,
i have the same problem. I got a looking new universal, I tried to updaty the system, but my battery is very broken, and it crashed while updating. Now, when I try to get in the bootloader, it's crashing.
I hope you can help me!! And I never worked with a windows phone, and I never tried to flash one, so I don't know sth. about doing this...
ebi
There is no backlight in bootloader mode. Go to bootloader, put the screen under a direct light source and see if it says SERIAL or USB (it will be very faint). If it doesn't, the device is almost certainly bricked. Make sure the battery isn't dead and try this while connected to USB or AC charger.
You could also try the mtty method in the stickied topic and see if the device responds at all. It could be a screen problem (long shot though).
Don't forget to remove SD and SIM cards before trying to flash.
Don't think my device is broken, as I successfully updated the ROM, then played with it, forget it more than 2 weeks on my desk. and then never wake up again.
So when battery is dried down, and the internal backup battery (I think it's a supercapacitor), are fully empty, then there is no way to bring it back to life. As the battery only start charging when at least we passed the bootloader sequence, how could we bring it back to life in that case ?
Just in addition to this, I already tried to replace the battery by an external power supply, taking care of the polarity. But without success.
Please advise.
Regards
me too,i put my device in bootloader but led not light(not light screen)
billounet said:
Don't think my device is broken, as I successfully updated the ROM, then played with it, forget it more than 2 weeks on my desk. and then never wake up again.
So when battery is dried down, and the internal backup battery (I think it's a supercapacitor), are fully empty, then there is no way to bring it back to life. As the battery only start charging when at least we passed the bootloader sequence, how could we bring it back to life in that case ?
Just in addition to this, I already tried to replace the battery by an external power supply, taking care of the polarity. But without success.
Please advise.
Regards
Click to expand...
Click to collapse
You would need a fully charged battery when flashing even if you had it on a charger while flashing, the charger will do nothing while theres a ROM being updated.
atl_luan said:
me too,i put my device in bootloader but led not light(not light screen)
Click to expand...
Click to collapse
There would be no lights when in bootloader mode nor lights on the screen but you will see SERIAL at the top and V2.01 or lower at the bottom but you would need to look closely as there are no lights.
Hi.
Im spanish, so my english is not perfect. Sorry about that.
Well i wil explain my problem.
I have an HTC One X, which one day,recived an "cachi" of water. (Cachi is an spanish type of glass for partys, about a liter)
The phone wont start in normal mode.Only starts in fastboot(VOL- + POWER) if are plug into wall charger (if i plug into pc, wont start at all)
The screen is working, but not the led from the screen, so if i want to see if thers something into the screen i have to use a torch light.
Next problem is i wont start into recovery (displays an triangle whit an exclamation insde in red), but i can start in fastboot sometimes.
But here´s another problem, it doesen´t have battery. I check whit fastboot the battery voltage and shows 47mv, yes 47mv.
So i try to charge whit an script, but its impossible because if i try to restart into bootloader pluged into pc, dont start and only shows windows searching for drivers every 5 seconds, because i think it disconected and conected itself every 5 second, so it fails at the time of install drivers.
Any solutions.Please!!
Thanks in advance
Rodrigo
Did you completely dry out the phone?
de4life said:
Did you completely dry out the phone?
Click to expand...
Click to collapse
In that day yes, but the same result
Y discover that one chip near the nvidia chip was broken in a corner.
This chips have a white point i dont have a photo sorry
So a few hours back I picked up my phone, but it didn't respond. A few minutes earlier it worked fine, and now it just seems dead. I cannot launch recovery mode or download mode. The phone does not respond to me holding the power button or something, there is no vibration and no visuals on the screen. Removing the battery and plugging it back in does not work. Leaving it charge for a while does not work. (assuming that it even charges). When I plug in the phone into my PC via cable I hear a sound that something is connected, but it doesn't show up on 'My PC'.
What do I do?
The same happened to my sister! Nothing worked, probably the motherboard died. Used it at leaset for spare parts for my other s4 mini. Especially the LED panel is so precious, it's cost is like half the price of the phone.
TranceMusic2014 said:
The same happened to my sister! Nothing worked, probably the motherboard died. Used it at leaset for spare parts for my other s4 mini. Especially the LED panel is so precious, it's cost is like half the price of the phone.
Click to expand...
Click to collapse
Can the motherboard really die like that? One moment its fine, the next second dead?
jeekay said:
Can the motherboard really die like that? One moment its fine, the next second dead?
Click to expand...
Click to collapse
Yeah, likely. I ain't a geek or sth, but the same happened to my sister. Was looking for a solution for hours, but it's probably some random variation in voltage or sth that burns some part on it and then it dies. You don't have to crack the phone etc., it can happen randomly.
TranceMusic2014 said:
Yeah, likely. I ain't a geek or sth, but the same happened to my sister. Was looking for a solution for hours, but it's probably some random variation in voltage or sth that burns some part on it and then it dies. You don't have to crack the phone etc., it can happen randomly.
Click to expand...
Click to collapse
Wouldn't a broken motherboard make my PC unable to make a sound when it's connected? Also, when it's connected to the PC and i hold the power button for ~15 seconds, it disconnects. This would mean that the power button still functions
jeekay said:
Wouldn't a broken motherboard make my PC unable to make a sound when it's connected? Also, when it's connected to the PC and i hold the power button for ~15 seconds, it disconnects. This would mean that the power button still functions
Click to expand...
Click to collapse
Then it's deffinitely NOT completely broken. A dead MB would definitely NOT identify the phone in the PC.
Did u try entering Download mode & connecting to ODIN, trying to load FW again?
TranceMusic2014 said:
Then it's deffinitely NOT completely broken. A dead MB would definitely NOT identify the phone in the PC.
Did u try entering Download mode & connecting to ODIN, trying to load FW again?
Click to expand...
Click to collapse
I cannot enter any mode. Pressing volume up or down + home + power doesnt do anything. How do I connect to Odin, and whats an FW?
jeekay said:
I cannot enter any mode. Pressing volume up or down + home + power doesnt do anything. How do I connect to Odin, and whats an FW?
Click to expand...
Click to collapse
FW = Firm Ware i.e. software that is flashed onto chips. aka ROM.
But if you can't go to download mode you can't flash stock ROM again. So Yes sounds likely some component has failed or maybe just a bad solder joint, a short, etc) which is not allowing power up,( either way you need someone to fix hardware & install stock using jtag for you, probably not worth the cost on our old phones in most countries. but if you can buy a used phone with eg a damaged screen or other problem you may be able to get 1 working phone by swapping parts eg power board ...
The same happened to me last august... I posted here, but no one ever helped me https://forum.xda-developers.com/galaxy-s4-mini/help/weird-bricked-gt-i9195-stuck-black-t3619023 i just think that it's some kind of programmed obsolescence, my phone was 4 years old and it just shut off and never light up again after closing a simple call... F*** Sammy and their timers!
Just happened my nephews phone. Was intermittently responding to buttons and now not at all. PC detects it and shows as "HS-USB Diagnostics 9008" in Device Manager.
There are a couple of guides online for using applications on the PC to interact with the phone using this device ID, but it seems to be mainly focused on LG phones. Anyone know if there's anything that can be done for Samsung devices?
The exact thing happend to my S4, it suddenly turnd of while im using it, did anyone find a solution?
My phone's battery was almost dead, so I bought a replacement battery and installed it. Nothing weird happened during the "procedure", and the battery charges fine, but the phone won't boot. The screen lights up to show the % when I connect it, but after it's off, it won't light up again when I press the power button.
I'm guessing something happened to the cable that connects the buttons to the MB. Or could it be something else?
luizedu said:
My phone's battery was almost dead, so I bought a replacement battery and installed it. Nothing weird happened during the "procedure", and the battery charges fine, but the phone won't boot. The screen lights up to show the % when I connect it, but after it's off, it won't light up again when I press the power button.
I'm guessing something happened to the cable that connects the buttons to the MB. Or could it be something else?
Click to expand...
Click to collapse
Impossible to know what has happened as we didn't see the repair.
Will the device boot to any partition ?
Recovery ? Download mode ?
I've seen several devices lose the OS if the battery goes completely dead....and pulling the battery would do the same thing on a susceptible device I would think.
Unless you can get into DL mode or recovery....it doesn't look good for restoring the device....g
gregsarg said:
Impossible to know what has happened as we didn't see the repair.
Will the device boot to any partition ?
Recovery ? Download mode ?
I've seen several devices lose the OS if the battery goes completely dead....and pulling the battery would do the same thing on a susceptible device I would think.
Unless you can get into DL mode or recovery....it doesn't look good for restoring the device....g
Click to expand...
Click to collapse
No, because it won't respond to any button press, so I can't boot it. Is it possible to access adb or something when the device is off? It does show and is identified on my PC when it's connected, so I don't think it's the case that its drives have been wiped.
luizedu said:
No, because it won't respond to any button press, so I can't boot it. Is it possible to access adb or something when the device is off? It does show and is identified on my PC when it's connected, so I don't think it's the case that its drives have been wiped.
Click to expand...
Click to collapse
So the PC is seeing the device but you have no screen activity....
Is there a chance that your display is not connected ?
I'm reaching here....but with all of the connections inside of the device....you may have missed something ?
gregsarg said:
So the PC is seeing the device but you have no screen activity....
Is there a chance that your display is not connected ?
I'm reaching here....but with all of the connections inside of the device....you may have missed something ?
Click to expand...
Click to collapse
The screen turn on fine when I first connect it and it starts charging, but I can't turn it on. I send to a repair shop and they diagnosed that the power button is not getting any juice, so I ordered a replacement for it, I just hope the issue on the cable and not on the connector in the MB.