Related
i tried to set up htc hd rom on my device ( kaiser )
after booting from my device
it work normally till the 1st third on stripe at booting screen
then this message appear
" the update is failed and terminated "
i made restart
but the phone doesn`t work after this
what shall i do
please help me
Have you tried installing a ROM made specifically for the kaiser or do you mean that the phone won't even turn on for you to get to the installation menu? It's not a great idea to install roms designed for other devices, especially one that has no similarity to the kaiser. The roms need a lot of updates before they will work on the kaiser such as kernel modules, drivers etc.
thank you for reply
but the phone doesn`t work at all ablack screen
even not recognized by pc
fayedcoo said:
thank you for reply
but the phone doesn`t work at all ablack screen
even not recognized by pc
Click to expand...
Click to collapse
So when you pull out the battery and put it back in and turn the phone on does it do nothing, no leds, no screen at all? if so there is a few things it could be, either a dead battery which needs charging, sometimes it takes a bit of charging before the phone will come to life again. You could have a shorted pin in the mini-usb socket on the bottom or elsewhere in the phone stopping it from turning on or the phone is bricked completely. What happends if you hold down the camera button whilst pressing the power button to turn the phone on?
i did every thing you imagine but nothing at all
just a black screen
battary is ok.
i did hard rest but nothing .
and the computer don`t recognize it.
i think it`s dead
any body can help me ??????????????
Sounds like the phone is completely bricked, if you tried hard resetting it, pulling the battery, and trying what scoot said to try -- Hold camera button while pressing the power button to boot the phone. When doing that you should get a tri-color screen.
i did this but still not work
what shall i do if it`s completely bricked
fayedcoo said:
i did this but still not work
what shall i do if it`s completely bricked
Click to expand...
Click to collapse
Get your battery charged through a universal charger (which charges battery in its own cradle), put it back into kaiser.
Connect USB cable to PC
Hold Camera button and Insert other end of USB cable into your kaiser.
Go to My Computer Proporeties > Device Manager and see if there is a composite device in the USB Devices drop down list. If there exists, all you have to do is to flash official ROM again.
While you installed an "HD" rom which was intended to run on HTC HD rather than HTC TyTn II, maybe you actually over-written your kaiser's SPL/Radio while doing so.
NEVER EVER FLASH A ROM INTEDED FOR ANOTHER DEVICE THAN THE ONE YOU HAVE
thanks for replay
but i think the problem not the battary because i tried another one 100% WORKING
i rally do what you say but i don`t observed any change
what happen to the device after upgrading with this funcken rom
is the motherboard bricked totally or somthing about the flash ???????????????
i respect your replay
thanxxxxxxx
fayedcoo said:
thanks for replay
but i think the problem not the battary because i tried another one 100% WORKING
i rally do what you say but i don`t observed any change
Click to expand...
Click to collapse
Hold Camera button, plug in USB Cable
If your device gets into three-colour screen, flash the official Windows Mobile from HTC
Hi,
I want drivers for xperia s, plz any body provide the link, also when i connect to chrage the red led, start diming whats the problem?
thx
If the led starts dimming it's not the driver problem.
Windows 7 will auto detect and install drivers for you, what's the problem?
kami2k said:
Hi,
I want drivers for xperia s, plz any body provide the link, also when i connect to chrage the red led, start diming whats the problem?
thx
Click to expand...
Click to collapse
Did you try another microUSB cable?
And does it starts dimming on wall charger?
cell didn't on at all when connected just red led dimming, whats the problem?
kami2k said:
cell didn't on at all when connected just red led dimming, whats the problem?
Click to expand...
Click to collapse
You can try to connect it to wall charger and leave it for a few hours, battery could be completely drained. I'm not sure why it's dimming, it never occurred on my Xperia S.
Is the bootloader locked? Did you try flashing fw with flashtool?
Windows 7 should automatically install 3 necessary drivers for the xperia S. 2 are auto installed when you first plug the phone in BEFORE you get the prompt to install PC companion (if you have that enabled in the phone). The 3rd auto-installs when you put the phone into flash mode (phone off, volume down held while plugging in the usb cord).
If you are having problems related to these drivers...head to device manager with the phone plugged in, look for 'portable devices' and uninstall the device and quickly unplug the phone. The next time you plug it in, windows should start the installation process over again. Do this before having flashtool running, or even installed for that matter (if you haven't yet)...
like anything windows though...your results may vary. I've done this on 2 different windows 7 machines...one at home, and one at my office. My home computer calls the flash mode driver 'SEMC Flash Driver' or something...my work machine calls it 'S1Boot Driver'...i've never seen these flipped, as in, never got the S1Boot driver at home or vice versa...yet flash tool works regularly on both, AS LONG AS PC companion isn't running...that screwed me up more times than i can count.
anyway though...after that, make sure PC companion is not running...and install flashtool and its driver package (might as well do all of them, the names are a bit confusing as you'll see the detailed installation list containing stuff not listed in the installation prompts).
After that, reboot windows...after the restart, if you're having issues with the phone...its a pretty safe bet its not the drivers...
while doing google i found that its battery is got dis, and its hard bricked windows doesn't recognize it and its just dead
kami2k said:
while doing google i found that its battery is got dis, and its hard bricked windows doesn't recognize it and its just dead
Click to expand...
Click to collapse
Hold the volume up key and power button for roughly 10 seconds. It should vibrate once after 2 or 3 seconds, then 3 times towards 10 seconds of holding both...after that, it should reboot...If the battery is truly dead, it may not fully boot...but will hopefully accept a charge after that...
if it doesn't work, report back...there are 50 page threads everywhere explaining how to get out of various stages of 'brickage'...
doesn't work plz share the url of thread
http://forum.xda-developers.com/showthread.php?t=1849170
there are more threads in the general section. If you search 'xperia brick' or something similar, you should find multiple threads. Be sure and read through them as much as possible, as one thread often answers/mentions any number of different causes and fixes.
Hi everyone, i have huge problem with ma Xperia. I bought it and it is not working.
When I wanted to power up it first time, nothing happened. Then i plugged to charger, and nothing.
Then i plugged USB to PC and it,s started. There was Android 2.3 i think, but the touchscreen didn't worked.
After unplug Xpera stuck at sony ericcson logo
Then i plugged usb with search button - uknown device, then with back - same thing unknown device.
The I removed battery, then insert it back and nothing happened with charger, usb, withou any cable - still nothing
Red light is flashing 3 times.
Whats the problem?
And can I run games without touchscreen?
kfasub said:
Hi everyone, i have huge problem with ma Xperia. I bought it and it is not working.
When I wanted to power up it first time, nothing happened. Then i plugged to charger, and nothing.
Then i plugged USB to PC and it,s started. There was Android 2.3 i think, but the touchscreen didn't worked.
After unplug Xpera stuck at sony ericcson logo
Then i plugged usb with search button - uknown device, then with back - same thing unknown device.
The I removed battery, then insert it back and nothing happened with charger, usb, withou any cable - still nothing
Red light is flashing 3 times.
Whats the problem?
And can I run games without touchscreen?
Click to expand...
Click to collapse
maybe the problem is your battery
and yes you can play games without touch but not all games just xperia play optimized games
raminta said:
maybe the problem is your battery
and yes you can play games without touch but not all games just xperia play optimized games
Click to expand...
Click to collapse
Is it possible, because as i said it works for short time without any cable, but stuck on SE logo.
I know i can play without touch, wrong question - my bad.
Can I run game, walking in menu without touch, using pad buttons?
kfasub said:
Is it possible, because as i said it works for short time without any cable, but stuck on SE logo.
I know i can play without touch, wrong question - my bad.
Can I run game, walking in menu without touch, using pad buttons?
Click to expand...
Click to collapse
Try to flash stock firmware with flashtool . Make sure you have drivers installed (from flashtool folder). If you have drivers installed but it still not recognized by flashtool, look in device manager and see what is written under "unknown device".
Phone can be used without touch screen (my Play had broken flex slider cable for more then a month). Navigation in launcher is with dpad, X is confirm, O is back. There is app in play store called "open notification" that I used to see notification, also, app "hard key soft keyboard" to type with dpads.
To be able to answer call, I used xposed framework for GB, with plugin to change home or search key for answering calls
As for games, it is per game. PSXperia games don't need touch screen (and I was playing mostly that while my touch screen was broken)
Bakisha said:
Try to flash stock firmware with flashtool . Make sure you have drivers installed (from flashtool folder). If you have drivers installed but it still not recognized by flashtool, look in device manager and see what is written under "unknown device".
Phone can be used without touch screen (my Play had broken flex slider cable for more then a month). Navigation in launcher is with dpad, X is confirm, O is back. There is app in play store called "open notification" that I used to see notification, also, app "hard key soft keyboard" to type with dpads.
To be able to answer call, I used xposed framework for GB, with plugin to change home or search key for answering calls
As for games, it is per game. PSXperia games don't need touch screen (and I was playing mostly that while my touch screen was broken)
Click to expand...
Click to collapse
Generally, Flashtool doesn't see my phone but there is one weird thing with that i think, i will write that later when, i will back home.
My device is always Unknown Device for Windows. With battery, without it, with back key, search key. Always Unknown device, and red light blinking continously.
And what do you mean "look in device manager and see what is written under "unknown device"."?
kfasub said:
Generally, Flashtool doesn't see my phone but there is one weird thing with that i think, i will write that later when, i will back home.
My device is always Unknown Device for Windows. With battery, without it, with back key, search key. Always Unknown device, and red light blinking continously.
And what do you mean "look in device manager and see what is written under "unknown device"."?
Click to expand...
Click to collapse
On PC, right-click on "my computer" and select "manage". Then on on left side select "device manager". Unknown devices is marked with yellow icon with exclamation mark.
For drivers, look in c:/flashtool/drivers folder (or whatever path you have it installed).
Red led is most likely empty battery, but too much reasons for that without proper troubleshooting (bad charger, bad USB cable, bad battery, bad charging circuit on battery, bad charging circuit in phone, damaged USB port or even short-circuit on motherboard). But it could also means damaged boot loader, and that's why I asked what is written in "unknown device" (it will be something like QHSUSB-something)
hi
Bakisha said:
On PC, right-click on "my computer" and select "manage". Then on on left side select "device manager". Unknown devices is marked with yellow icon with exclamation mark.
For drivers, look in c:/flashtool/drivers folder (or whatever path you have it installed).
Red led is most likely empty battery, but too much reasons for that without proper troubleshooting (bad charger, bad USB cable, bad battery, bad charging circuit on battery, bad charging circuit in phone, damaged USB port or even short-circuit on motherboard). But it could also means damaged boot loader, and that's why I asked what is written in "unknown device" (it will be something like QHSUSB-something)
Click to expand...
Click to collapse
if it is detected in testpoint .... zeus device or qhusb in device manager .... contact me on gtalk [email protected]
There is some progress i think, and maybe degress(?) . I left phone with charger for all night. At the morning for my surprise there is green light. I tried power on, and its work. Almost. Touchscreen is didn't working. But thats nothing. When I unplugged from charger it switch off. Now I can power on it with charger or USB Cable, but without it it's stack on SE logo.
I was think thats battery issue, but it isn't. I pluuged phone directly to USB 5V(Red- "+", Black - "-") without battery of course. Same thing, stack on SE logo.
What can I do next? Can I do anything with that?
EDIT I tried flash stock rom via Flashtool, and nothing. Flashmode and fastboot are working.
Hi,
my M8 doesn't turn on anymore. Already tried to change the battery, already tried to start it with VOL+ vor a couple of minutes, tried VOL+ and VOL- for a couple of minutes - nothing. I can't get into bootloader, i can't boot the phone - BUT:
- After connecting the phone to the PC a device "Qualcomm HS-UB QDLoader 9008 (COM10)" shows up
- When putting the charging cable only half the way in the charging LED turns on for 1-2 seconds and then off again
- When trying to do the VOL+ and Power method the charging LED turns on very short every 10-15 seconds as long as i hold the keys
Is it completely dead? Or can i try to flash something with qualcomm tools from here? Its a non-provider phone (HTC_102 i think) and the android variant.
The last thing i did was htcdev unlock after i got it from htc repair where they replaced the motherboard. i installed twrp and then miui7 and after this viperrom and leedroid. With miui it turned on but not every time (i don't know why) but after leedroid it doesn't even get into bootloader.
I don't think this is rom related and more of a hardware issue but maybe you have some ideas. The phone seems to be dead anyway, so let's try something.
Thanks
Dacoco said:
- When putting the charging cable only half the way in the charging LED turns on for 1-2 seconds and then off again
- When trying to do the VOL+ and Power method the charging LED turns on very short every 10-15 seconds as long as i hold the keys
Click to expand...
Click to collapse
What color charge LED?
Orange
Dacoco said:
Orange
Click to expand...
Click to collapse
I have the same issue. Same indicators. Just happened after charging overnight phone seems completely dead. Tried everything. (Light trick, Volume Up & Down w/ Power)
For the most part, if you've charged the phone for several hours, and all your are getting is orange/red LED (I would call it red, but maybe I'm not remembering it correctly) and the button combos don't work, its probably bricked.
Try holding power+Vol up for a minute or so (it will sometimes take that long to reboot, in certain circumstances). Also try Power+Vol up+vol down (but it sounds like you did already).
Also try the button combos with or without the charger attached and plugged in. In can think of at least one user, that had success with the charger plugged in, when they had lost all hope.
Basically, the device will come up with the Qualcomm Download message on your PC anytime the phone is not powered on. So it can be an emmc failure, or a dead battery. You can try replacing the battery, but that can just end up as a disappointment (which looks like may be the case for the OP). Or you can even have the Qualcomm message come up, if the charge is too low. I've had that happen once, gave me a heart attack. Red LED, and no response to button combos. I let it sit on charger for a few hours, then holding power+vol up for a minute made it boot, much to my relief.
---------- Post added at 03:51 PM ---------- Previous post was at 03:49 PM ----------
Dacoco said:
Orange
Click to expand...
Click to collapse
I would have been more hopeful if it was a green LED, appearing for a second when you connected the charger. That would have made me think maybe the charge port is just loose.
Same problem
having the same problem and i have noticed that when I plug it to pc then I shows qgusb dloader and when I press power button or any other button combination then I stop showing as qgusb dloader it appears as device is unplugged and then if I replug it then it won't show anything nor led neither qhusb..But after 10 min or so if I plug it then it again shows led and qhusb and I have also noticed one more thing that if I plug it in charger then led just blink for some microseconds but when I plug it to pc led blinks several times dim solid for 2 3 seconds is there any hope?
I reached this stage by installing unknown ROM .
By the way I have one more HTC one M8 but its from different career (at&t) and it's also rooted and custom rom installed but its in very bad condition just working but i m thinking about replacing motherboard or battery so i can fix it it this idea succesfull ?
narshi shukla said:
I reached this stage by installing unknown ROM .
Click to expand...
Click to collapse
What do you mean "unknown"? Do you mean, you can't remember exactly which ROM you flashed?
I presume you don't mean you flashed something, without knowing what it is.
Do you remember anything about the ROM?
What carrier version of the M8 are you talking about?
S-on? If so, its hard to brick this phone with s-on.
Hello All,
I have the exact same issue ...
It started by showing messages like "android core/services has/have stopped". I rebooted, then there was no mobile network connection -> No IMEI.
I had no worries, that happened also in the past and I could solve it with a dirty flash.
Then I went to Recovery, dirty flashed my ROM (Android Revolution), phone rebooted and started building application cache.
At some point, it started, then some more caching and ... boom, blackout.
It doesn`t respond to anything. No power+volume combination, anything.
I have even opened it up and removed the battery connector.
Without battery, when I connect it to the power source, via USB, the RED light turns on for a second and the Off. ..
Also, when connected to the PC, it is identified as : " Qualcomm HS-USB QDLoader 9008 " .
Are there any repair possibilities, besides motherboard replacement ?
Thank you in advance.
dachriss_13 said:
Hello All,
I have the exact same issue ...
Click to expand...
Click to collapse
Please don't post the same question to multiple threads. One place is enough. It makes it confusing to those trying to help you, and it's therefore against forum rules.
Understood, won`t happen again.
Thank you.
I was flashing the zui with qfil and now my zuk is with a black screen and vibrate every 32 seconds
Qfil error: https://imgur.com/a/pUjb3IB
Chewbaccaun said:
I was flashing the zui with qfil and now my zuk is with a black screen and vibrate every 32 seconds
Qfil error: https://imgur.com/a/pUjb3IB
Click to expand...
Click to collapse
Well use this
https://forum.xda-developers.com/lenovo-zuk-z2/how-to/lenovo-z2-plus-zuk-z2-plus-hard-brick-t3713126
JV Spartacus said:
Well use this
https://forum.xda-developers.com/lenovo-zuk-z2/how-to/lenovo-z2-plus-zuk-z2-plus-hard-brick-t3713126
Click to expand...
Click to collapse
problem solved
Nothing helps..?
(I will post this also here, cos no one answered @ zukfans yet)
Hi! I think I need to ask help now.
I've managed to hard brick my Z2 with QFIL trying to update the phone from zui 2.something to 3.5. Well obviously that did not end up good.
My phone went to a stage described in some cases: White light blinking every 15 seconds or something and phone vibrating. Ok, I tried to shut the phone down by keeping and releasing after second blink. Did not work. Then I tried to hold for two or more minutes. It seemed to work first but suddenly also that didnt work (kept power pushed for ten minutes or more). Ok, the I made the cable described here. I did a jumper cable from my usb extension cord. Windows reacted to the phone but did not recognize it. Nothing showed up in device manager or QFIL or MiFlash. The phone keeped on vibrating and a left it like this for the night. I guess battery ran out and phone finally shutdown.
I continued and same results. One time windows recognized a unknown device for some seconds but it did not show up in device manager or MiFlash. After that nothing. Now the phone only blinks the light. It vibrates only when trying to charge it or plugged in PC. I don't now if it's on or not. Anyways, the same results with windows: reaction, but no recognition. I've tried to pull usb out and change to another slot etc.
Also I've installed Zuk 1.05 drivers, MiFlash and tried also with Qualcomm drivers. Uninstalled everything and tried again. Nothing seems to help.
Could this be because of Windows 7? Or bad extension cord? Or what...? Any advice would be appreciated.
edit: It was not Windows problem I guess. I installed fresh Windows 10 with no help. Actually worse. No Windows is not reacting at all. Maybe it's the jumper cable I created. I didn't want to ruin my only USB-C.
edit: Ok. Back to Win7. Now there is no reaction at all also in Win7. The phone vibrates when connected to pc. Otherwise phone seems to be off. No lights flashing. If power is held down white led flashes briefly but no vibration.
edit: Now if I connect the phone to laptop the led blinks every 0.5 seconds... I have no idea how turn the phone off. It seems to be off while not touched because nothing is happening...
@Pelepako
Try this,just a copy paste
2.0). Turn off the phone. If the phone boots up (reboots) then immediately to point 2.1
2.1). Put wire on the 2nd contact on the left
. And together with the wire insert into the PC (at the same time the phone is already connected by cable).
2.2). After 5-10 seconds, take out the usb plug with the wire. Remove the wire and insert the plug back.
2.2.1). If you do not have a bootlap, but it hangs on MI, on the boot process, etc. Hold the POWER button and insert the USB plug with the wire into the usb port. The screen goes out and you get what you want.
3.1). Your device in EDL mode.
3.2). Click REFRESH in Miflash and see your device in COM format.
3.3). Flash firmware at your discretion.
Thanks for the instructions.
Still nothing. Windows 10 does not recognize the phone in any way. The phone vibrates almost immediately when plugged in. Then nothing. Sometimes (before) I got Windows to recognize it as "unknown device".
2.0 Turning off the phone. I'm unpluggin the battery. I guess that does the job? At least nothing is flashing or vibrating.
2.1 I inserted a paper clip as in the picture.
Dunno if it's a driver thing. I've installed different Zuk driver version, Qualcomm, MiFlash, QFil, ADB.. you name it. I've turned on the Test Mode in Windows (driver signature). I've tried two different cables. One of them is the original. Tried the paper clip trick and the wire connect trick. Nothing is working. There has to be some flaw that I'm not noticing. Can't be the only one who really got his phone bricked...
About the drivers:
Ive installed zuk 1.05. Is it ok? Tried also 1.06 and 1.08.
How to install ADB. I've used ADB installer and installed system-wide. Should I also install the device driver (Google)?
Qualcomm drivers. Cannot manually install. With Miflash etc. some Qualcomm drivers get installed.
Do I need to install Fastboot and ADB "executables"? Where do I need these in my situation? Nowhere?
What abou QFIL? Is it necessary if I'm using MiFlash?
narshi shukla said:
@Pelepako
Try this,just a copy paste
2.0). Turn off the phone. If the phone boots up (reboots) then immediately to point 2.1
2.1). Put wire on the 2nd contact on the left
. And together with the wire insert into the PC (at the same time the phone is already connected by cable).
2.2). After 5-10 seconds, take out the usb plug with the wire. Remove the wire and insert the plug back.
2.2.1). If you do not have a bootlap, but it hangs on MI, on the boot process, etc. Hold the POWER button and insert the USB plug with the wire into the usb port. The screen goes out and you get what you want.
3.1). Your device in EDL mode.
3.2). Click REFRESH in Miflash and see your device in COM format.
3.3). Flash firmware at your discretion.
Click to expand...
Click to collapse
Ok. Just found out that the only 2.0 port is broken. There is no second pin. At least anymore. I might have broken it in some point.
Other reason for malfunctioning could be the circuit board of the phone. The previous owner in all his wisdom had glued the battery cover with super glue. As I opened it it ripped of some of those circuit materials that conduct electricity. The broken part is near the usb port of the phone. Maybe if I put the cover back it will work cos the ripped parts are still glued to the back cover..
So back to the issue.
The broken part of the phone seems to be speaker so it should not affect the connection I guess. I also fixed with conductive silver paint. Still, no help.
Just found out that the charger and probably also the cable are not original ones. Maybe this is the reason for this is not working. I cannot come up with any other solutions. Now I would need to know which usb cable would qualify for the procedure. How can tell which is a proper cable before buying it? Also does the micro-usb cable work if I have the convertor dongle (Samsung made)?
edit:
Ok. Sometimes the led blinks every 0.5 sec. Sometimes phone vibrates every fifteen or something seconds. Only way to get the computer to react is with modded usb extension cord -> green to black. This way Windows recognizes an unknown device. That's it. I cannot install Qualcomm drivers for this or do anything else. This way Windows makes this connected sound every 0.5 seconds and the phone led blinks. After a while it stops and the phone is marked as "unknown device". Also if I connect the phone to a charger it blinks all the time (0.5s) and vibrates occasionally. Then after a while the led calms down and blinks every 15 seconds. And then back to 0.5s with vibration. All these symptoms seem unclear and I haven't found anyone suffering from same kind of problems...
Really am I the first that really bricked this one? I didn't even use the phone yet. Just checked it and tried to update the system cos it was old version.
I assume that the phone has to be off after disconnecting battery cable so that should not be the problem here.
@narshi shukla
I turned the phone off by removing battery. It does not reboot after shut down before I connect it to computer. Few seconds after connecting to pc it vibrates shortly. Nothing else happens after that. Same with and without the wire.
I've tried so many different methods that I'm giving up with this I guess. Am I the only one who got his phone permanently bricked. After all I tried to flash by following instructions. The flash failed and phone went on crazy vibration and screen on for some seconds after that it was vibrating every 15 seconds. Then suddenly it stopped doing that. Now it does only if I plug it to pc or charger.
The "black green wire trick" is strange. If I only connect those two wires nothing new happens BUT if I connect green to black and black to green by tying instead only touching the phone vibrates and led blinks every 0,5 seconds and windows also makes the connection sound even though it is not working.
narshi shukla said:
@Pelepako
Try this,just a copy paste
2.0). Turn off the phone. If the phone boots up (reboots) then immediately to point 2.1
2.1). Put wire on the 2nd contact on the left
. And together with the wire insert into the PC (at the same time the phone is already connected by cable).
2.2). After 5-10 seconds, take out the usb plug with the wire. Remove the wire and insert the plug back.
2.2.1). If you do not have a bootlap, but it hangs on MI, on the boot process, etc. Hold the POWER button and insert the USB plug with the wire into the usb port. The screen goes out and you get what you want.
3.1). Your device in EDL mode.
3.2). Click REFRESH in Miflash and see your device in COM format.
3.3). Flash firmware at your discretion.
Click to expand...
Click to collapse