After dropping my desire the screen had an obvious crack (no crack in the glass/digitiser) and displayed crazy colours from the crack, spreading across the screen over the course of the day until finally going completely blank.
Bought a new screen on ebay, same part number, same samsung AMOLED. Replaced today and the phone exhibits exactly the same behaviour. Switches on, digitiser works to the extent I can unlock and lock the phone, but screen is constant black. After a few switch on/offs the screen showed two green lines at the top and about half way down upon unlocking, that went away after another lock and unlock.
Pretty confident that the disassemble/assemble went ok and I didnt stress any flex connectors or similar... so have no idea what could still be wrong....
As I say, phone boots and can unlock/lock (makes the right noises etc) and is recognised by computer when plugged in.
Could using the phone until the screen completely stopped working have broken the controller or something?
Any input greatly appreciated.....
EDIT:
Just switched it on again, green line at top from keyboard lighting point, then the whole screen went blue on unlock. :S
This sound like a dying something, or maybe just bad contacts? Find it strange that unlocking has an effect....
Might be a bad connection or little shortcut?
Here is an official video on how to assemble and disassemble the device, http://forum.xda-developers.com/showthread.php?t=768535. Don't know if that helps but you can check if you did something wrong in the progress.
"..Bought a new screen on ebay.." Do not buy Chinese, buy the original.
ronijs19 said:
"..Bought a new screen on ebay.." Do not buy Chinese, buy the original.
Click to expand...
Click to collapse
Seeing as the part was shipped from my country and had the exact same markings and serial numbers as the part I removed, I dont think this is the issue.
Thanks for the video, will disassemble and clean all contacts later today.
Was mainly posting to see if people had heard of/experienced the same issue, trying to ascertain whether it could be a faulty replacement or if its possible to break the hardware that runs the screen.
A good fake can be hard to tell apart from an OEM part...
So the consensus is that its a fake replacement? Really? The screen seems identical in all markings and connectors, my only conclusion can be it came from the same factory. What market would there be in producing defective replicas of mobile phone components?
Anyway I have sent the screen back to the seller for a replacement.
Any response to my other questions? Is it possible to damage the hardware that drives the screen by using the phone with a dying screen to the point of blank display?
Reading through another thread: http://forum.xda-developers.com/showthread.php?t=933866
Post #6 suggests the rom on the phone could have an effect, is this the case?
Thanks for any input.
Rom couldn't be the issue if you've installed the exact same screen.
My guess would be a loose connector.
Sent from my HTC Desire using XDA Premium App
My desire lives!
Replacement screen worked just fine....
Thanks for everyones responses!
Can you post the link to the seller on ebay, from whom you bought the display?
Related
hi, have searched and searched on the forum but no real answer to my problem.
i dropped my htc one x and the glass cracked, so i sent it away to a supposed reputable firm (i didnt realise htc repaired phones aswell otherwise i would have sent it there)
anyway the lcd display and brightness worked perfectly, the company have replaced the screen and now the backlight no longer works and flickers when touched or cpu is being used.
they have said it is the display IC, and coil etc,
they say that this was caused by the phone being dropped, and not by them and they have charged me (they take payment before sending phone back), they initially took the phone back, and 3 weeks later they have decided to wash there hands of it, have put the phone back together shodily tell me i have to put up with the phone as it is, and refuse me a refund.
they acknowledge that the ic was fine before they took it apart, but blame it on the nature of the phone design as to why it now doesn't work.
i would post link to another forum explainingg the possible issue (has no explanation of cause though) and pics of the phone has been returned to me, but i can't because im a noob
Basicly the question is,
Who is at fault?
And how could the ic get shorted out,
The backlight flickering is likely to be poor installation of the new screen.
Again this is an old example I'm referring to here. I used to replace the screens on the Nokia n95 quite regularly.
You get the screen assembly and the ribbon cable which attached to the motherboard.
If the ribbon cable was not seated 100% perfectly I would get the exact same symptoms you are describing.
No backlight. Pressing down on the screen would either get it to flicker or come on for a while.
It shows a poor connection. I took the screen back out and repositioned the cable back in. Reassembled and then it was fine after
Sent from my HTC One X using xda app-developers app
sx_turbo said:
Basicly the question is,
Who is at fault?
And how could the ic get shorted out,
Click to expand...
Click to collapse
Hi mate did you managed to get this sorted I am having the exact trouble same issue with a company call Elite Phones and Computers.
They are saying that the IC shorted out and the only repair would have to be a replacement board.
sx_turbo said:
hi, have searched and searched on the forum but no real answer to my problem.
i dropped my htc one x and the glass cracked, so i sent it away to a supposed reputable firm (i didnt realise htc repaired phones aswell otherwise i would have sent it there)
anyway the lcd display and brightness worked perfectly, the company have replaced the screen and now the backlight no longer works and flickers when touched or cpu is being used.
they have said it is the display IC, and coil etc,
they say that this was caused by the phone being dropped, and not by them and they have charged me (they take payment before sending phone back), they initially took the phone back, and 3 weeks later they have decided to wash there hands of it, have put the phone back together shodily tell me i have to put up with the phone as it is, and refuse me a refund.
they acknowledge that the ic was fine before they took it apart, but blame it on the nature of the phone design as to why it now doesn't work.
i would post link to another forum explainingg the possible issue (has no explanation of cause though) and pics of the phone has been returned to me, but i can't because im a noob
Click to expand...
Click to collapse
had the same ..from now ill always send it to htc if something is broken again it costs the same i found out
Yesterday i dropped my device from one feet. It turned off and i turned it on.
Now lower part of screen and capacitative buttons dont work. i will attach a image(non-working area outlined in red)
My warranty has expired so i cant exchange it for a new one. What should i do? Can i fix it by myself?
Please help me
Fycola123 said:
Yesterday i dropped my device from one feet. It turned off and i turned it on.
Now lower part of screen and capacitative buttons dont work. i will attach a image(non-working area outlined in red)
My warranty has expired so i cant exchange it for a new one. What should i do? Can i fix it by myself?
Please help me
Click to expand...
Click to collapse
Hi,
Only thing I can think of is that somehow it has damaged the cable from the touchscreen or the tiny wires that feed into the cable without damaging the screen. I came across a brand new screen I was replacing once for someone that had a similar problem where the bottom left hand corner wouldn't respond to touch unless there was firm pressure on the screen to create contact, and this was a brand new screen. It could also be that the touchscreen connector needs to be pushed back onto the board if it's come a bit loose.
If this is the problem, you can fix it by yourself although I'd have a good look around youtube, there are heaps of DIY videos of how to replace screens. If you do go down this path I recommend you replace the touchscreen/LCD/LCD frame in one go, as it's generally already pre- assembled the only thing here is that there are 3 brands of LCD's HTC used with the phone and they aren't all compatible, and you can only tell by pulling down your phone and looking at the LCD flex cable colours, and the other thing is that the screens that are available aren't always the same quality as the original. If this sounds to hard your best bet is to take it somewhere and diagnose the problem just in case it's something else
Yes, like it turned itself off but it did not go off as I was still getting audible email notifications. Tried everything speaking with Google support and then even Asus support who told me to go to their website and fill in an RMA form. This unit is 13 months old-out of warranty. There is nothing on the form relevant to the nexus to fill in so you cannot continue with it. So I am stuck right now and do not know what to do if anything. Any help would be appreciated.
claypoole said:
Yes, like it turned itself off but it did not go off as I was still getting audible email notifications. Tried everything speaking with Google support and then even Asus support who told me to go to their website and fill in an RMA form. This unit is 13 months old-out of warranty. There is nothing on the form relevant to the nexus to fill in so you cannot continue with it. So I am stuck right now and do not know what to do if anything. Any help would be appreciated.
Click to expand...
Click to collapse
Normally, 3 things can go wrong:
1. The cable is not connected properly. This could be caused by any impact. You take off the back cover and reseat it. It's the amber cable that runs the length of the battery. Be sure to check both ends. The one on the motherboard's end is in plain sight. The other end is hidden beneath the daughter board at the bottom of the tab, so you need to remove it to inspect the connection.
2. The backlight which illuminates the display went out. You can check this by turning the tab on and taking the tab to a dark room and shine a flashlight on the screen. If you can see the icons or the boot page, the back light is bad. The bad news is that you'd have to remove the lcd/touchscreen unit to replace the backlight. 10 times out of 10, when you do this on an original tab, you will break the touchscreen. Since it's glued to the lcd with LOCA (liquid optically clear adhesive), you will have to separate them, fix the backlight, buy a new touchscreen, then reassemble the whole thing. Most people would find it simpler to just buy a new lcd/touchscreen combo. If you're game though, I can give you an lcd back with a working backlight strip.
3. The video circuit on the motherboard went belly up. To test this, you need a micro usb to HDMI adapter like the one here , and a newer lcd TV. If nothing shows on your TV, the GPU is probably dead, in which case the only practical solution is to replace the motherboard since it's impossible to replace the GPU at home.
Good luck.
graphdarnell said:
Normally, 3 things can go wrong:
1. The cable is not connected properly. This could be caused by any impact. You take off the back cover and reseat it. It's the amber cable that runs the length of the battery. Be sure to check both ends. The one on the motherboard's end is in plain sight. The other end is hidden beneath the daughter board at the bottom of the tab, so you need to remove it to inspect the connection.
2. The backlight which illuminates the display went out. You can check this by turning the tab on and taking the tab to a dark room and shine a flashlight on the screen. If you can see the icons or the boot page, the back light is bad. The bad news is that you'd have to remove the lcd/touchscreen unit to replace the backlight. 10 times out of 10, when you do this on an original tab, you will break the touchscreen. Since it's glued to the lcd with LOCA (liquid optically clear adhesive), you will have to separate them, fix the backlight, buy a new touchscreen, then reassemble the whole thing. Most people would find it simpler to just buy a new lcd/touchscreen combo. If you're game though, I can give you an lcd back with a working backlight strip.
3. The video circuit on the motherboard went belly up. To test this, you need a micro usb to HDMI adapter like the one here , and a newer lcd TV. If nothing shows on your TV, the GPU is probably dead, in which case the only practical solution is to replace the motherboard since it's impossible to replace the GPU at home.
Good luck.
Click to expand...
Click to collapse
Did anyone else read this response and want to hit the edit button, and then type in huge letters "Time to buy a new Nexus!"
Thank you for your detailed reply. I checked the cable from the MB at both ends. Seems OK on the connections. I am unable to turn on the tab to check the backlight. That's about as far as I can go with it at this point. I am thinking that this tab is toast and to make matters worse, the abominably bad Asus customer service. I am considering replacing this with a Samsung and be done with it.
claypoole said:
Thank you for your detailed reply. I checked the cable from the MB at both ends. Seems OK on the connections. I am unable to turn on the tab to check the backlight. That's about as far as I can go with it at this point. I am thinking that this tab is toast and to make matters worse, the abominably bad Asus customer service. I am considering replacing this with a Samsung and be done with it.
Click to expand...
Click to collapse
Hey, don't lose hope! Samsung is not any better specs or quality-wise (especially the display). If you're gonna butcher the thing anyway, might as well find out. I was gonna suggest to lend you a used lcd for you to test, but I realize people for some reason are extremely wary of gratuitous offers so I won't. But if you value it, try to get a screen with a good lcd but broken digitizer on Ebay. They wouldn't cost more than 15 bucks. Once you can determine it's not the motherboard, we can go from there. I can guide you on the replacement part if you want. I'm just a hobbyist, but I have messed around with this thing enough to tell.
Graph, you are kind to offer. I also have noticed that the glass has a few cracks in it as well. At this point, I can't turn it on. It seems like when I punch the on button in there is extremely little movement if at all. So I don't know if it is still on which I don't this it is or it shut itself off. When it was black screen and on, I was getting my email notifications audibly but since yesterday-none. I am not looking to spend big bucks on these things as essentially all I do mostly is use for reading. I do want to stick with android if I replace this. I know samsung does not have as good resolution but seems to get good reviews from users.
Hi,
I have to following problem:
My HTC One M8 has colorful grainy static screen and sometimes the picture turns off, like a cable is loose. I read all the forums and search google all over for a solution, most of them claimed that after a panel replace it will be fine. I switched the whole front panel for a new one, but after assembly i have the same problem. The phone is working, because i can unlock the screen lock, turn off the phone, i get the notifications and everything, but the screen is just static noise. I'm assuming that maybe it is some graphic fault, but not related to the lcd panel or the cables (they are all brand new, and i double checked all of them). Is the logic board responsible for the image? What should i try to replace next the upper motherboard, or the middle logic board?
Shad
pic related
imgur . com/a/kjR6F
Oldai3912 said:
Hi,
I have to following problem:
My HTC One M8 has colorful grainy static screen and sometimes the picture turns off, like a cable is loose. I read all the forums and search google all over for a solution, most of them claimed that after a panel replace it will be fine. I switched the whole front panel for a new one, but after assembly i have the same problem. The phone is working, because i can unlock the screen lock, turn off the phone, i get the notifications and everything, but the screen is just static noise. I'm assuming that maybe it is some graphic fault, but not related to the lcd panel or the cables (they are all brand new, and i double checked all of them). Is the logic board responsible for the image? What should i try to replace next the upper motherboard, or the middle logic board?
Shad
pic related
imgur . com/a/kjR6F
Click to expand...
Click to collapse
I've got the exact same thing here.... Searched a lot around without finding anything that has resolved my case. I ordered a replacement screen for a cracked screen on the first phone, but when I tested the LCD before I assembled everything together it was showing just noise like in your picture. I assumed the LCD was bad, so I ordered a new one. But the new one was acting exactly the same.
Yesterday, I was approached by another one who needed help with their M8, and that phone needed to have its volume buttons replaced. So, I reused the parts from the old M8, but when I booted the phone after repair, it showed this same noisy screen as the first M8 I tried to repair. Anyone here that knows these phones and what is going on here? I'm pretty sure I have 3 working LCD's here now, and suspect something strange going on with the mainboard or controller for screen.
Anyone?
The battery on my HTC 10 was completely shot and needed to be replaced. I'm a careful person by nature and this being my first phone repair, I bought an extra screen just in case something happened getting it apart. Followed a guide by jerryrigeverything on how to take apart the phone, got the battery replaced, everything seemed to go smoothly. When I went to test the display before screwing everything together, the new screen I installed lit up, but the right half of the display only showed as a repeating segment from the middle of the screen. Thinking the connector was loose, I disconnected and reconnected the display and made sure everything was tight: same problem. I reinstalled the original display, which I made sure had worked after cutting through the adhesive before I disconnected it, and now the old display is also showing the same issue.
The touch screen on the broken side of the display still works, I'm able to type PIN numbers and whatnot even though I can't see them properly. Only thing I can think of is maybe the connection actually got some debris or something inside of it? I don't think I damaged anything, as I was super careful, but it was also my first time opening up a phone.
Sorry for the inefficiently worded post. Any help would be really appreciated.
Did you resolve this?
I have exactly the same issue you describe after my screen replacement (with two new screens) Believing the first was a dud.
I have done many screens/batteries on my m7, m8's previously never having a problem.
I'm currently back to running my M8 and miss my 10!
Anyone reading this and has any suggestions they are all welcome!!
Thank you in advance
Exactly the same issue this guy has
https://youtu.be/RpdCuMiTOn8
I'm now wondering if it is just bad aftermarket screens?
Has anyone else replaced their screen successfully, if so where did you get the screen?
Thanks Rory
I have been having the same problem. I just tested screen number 4 that has the same exact problem. Is there a specific brand that is known to test well?
I dropped my 10 in water at work...believe it was a salty water at that. It stopped working completely. I opened the phone to check the internal components for damage and I broke the LCD doing so. I replaced the battery and the screen at almost the same time. I think it may have been a week or two apart.
The battery is still working. The screen worked initially but the phone kept getting really hot and the heat kills the phone. I tried keeping it cool at all times which kept it operational. It hasn't been activated since I quickly replaced the phone with another of my lines upgrades. I went back to the phone to check it out and try using it as a replacement for my daughter but the screen no longer works.
The battery charges just fine...the led light indicates that well. I've tried reinstalling it several times with no success getting the screen working again. I tried the original screen to check and I could see light and it was responding but its not usable so I'm stuck with a phone that has a new non-working display. I think the brand was called DIYRepair or similar.
If anyone has encountered this and has advice...I'd be happy to try anything.