Develop Bugs

help with ROM upgrade and problems with SIM

Hi i have a Diamond that i bought in Russia and now i want it in Swedish.
So i downloaded a swedish ROM: DIAM1.37.413.3SVE
And i have the Unsign-Hard-SPL-Diamond-Oilnex 1.40
So when i have installed the SPL, And the Swedish ROM, Everythings OK, Runs like normall BUT when i put a SIM Card inside the Diamond it wont work, Cant call, The Touch screen will not work right, Its freezing and booting the device... Why? Do i need some "Radio" or whats it called?
Im very new about this som please help me and explain good-easy how to do step by step
When i start the Diamond it says;
R 1.00.25.03
G 52.26a.25.09
D 1.37.00.00
If that says anything?
Hope for some expert help. Best regards. Micke!

micke99 said:
Hi i have a Diamond that i bought in Russia and now i want it in Swedish.
So i downloaded a swedish ROM: DIAM1.37.413.3SVE
And i have the Unsign-Hard-SPL-Diamond-Oilnex 1.40
So when i have installed the SPL, And the Swedish ROM, Everythings OK, Runs like normall BUT when i put a SIM Card inside the Diamond it wont work, Cant call, The Touch screen will not work right, Its freezing and booting the device... Why? Do i need some "Radio" or whats it called?
Im very new about this som please help me and explain good-easy how to do step by step
When i start the Diamond it says;
R 1.00.25.03
G 52.26a.25.09
D 1.37.00.00
If that says anything?
Hope for some expert help. Best regards. Micke!
Click to expand...
Click to collapse
Hi i'm not an expert, but it's not right that when you start the Diamond it says "1.37.00.00" when in fact you have installed ROM "1.37.413.3SVE".
I would suggest try flashing the hard SPL again, then flash the new ROM again. (and use with the signed version of Hard SPL this time for safety against bricking).

Now i tryed the Signed 1.30 Oilnex SPL. And then flashed again with the Swedish ROM.
When i flashed with the Swedish ROM it says that i have 1.30 Oilnex in the display.
But when i start the diamond it still says 1.37.00.00 is that right?
Still it wont work with SIM inside...

micke99 said:
Now i tryed the Signed 1.30 Oilnex SPL. And then flashed again with the Swedish ROM.
When i flashed with the Swedish ROM it says that i have 1.30 Oilnex in the display.
But when i start the diamond it still says 1.37.00.00 is that right?
Still it wont work with SIM inside...
Click to expand...
Click to collapse
That is not really a problem. On my phone, which works perfectly well, I also only see the major number release (i.e. 1.37.00.00). I don't think that's a symptom of why your phone is not working. You should try to find the cause elsewhere, but I also do not know where you should start.

Yes because the phone is working with russian ROM, But not when i install the Swedish... hmm...
Any clues=?

i can help you - flash this:
http://rapidshare.com/files/129598071/Diamond_Radio_1.00.25.05.rar
and your swedish rom will work

O2 xda diamond flashing problem

I have o2 xda diamond -but when i see the device setting it's say (htc touch diamond p3700) with ID DIAM300
rom 1.93.831.1 wwe
rom date 07/18/08
radio version 1.00.25.05
protocol 52.29.25.12h
first
i was flash my phone with hard -spL-1.37 olinex and i cant flash any rom
then i flash hard-spL-1.39 olinex .hard-spl-1.40 olinex -development verision .
When i inter boot loader it's hard-spl40 olinex
but i cant flash any rom it's error invaild id trying a lot rom wm6.1
nothing work it's closed at 1% then i see the error
then i trying flashing the rom by storege method but's not work too....
i no know what's the wrong ???
Please help me .......
Sorry for bad language

make manual usbflashing threecollor settings and use normal ruu for flash.Maybe im more time use for ole htc diamond because show me message low battery but battery is full 70-80 % and im use usbsettings <threecolor menu> and flash

a_2004_81 said:
I have o2 xda diamond -but when i see the device setting it's say (htc touch diamond p3700) with ID DIAM300
rom 1.93.831.1 wwe
rom date 07/18/08
radio version 1.00.25.05
protocol 52.29.25.12h
first
i was flash my phone with hard -spL-1.37 olinex and i cant flash any rom
then i flash hard-spL-1.39 olinex .hard-spl-1.40 olinex -development verision .
When i inter boot loader it's hard-spl40 olinex
but i cant flash any rom it's error invaild id trying a lot rom wm6.1
nothing work it's closed at 1% then i see the error
then i trying flashing the rom by storege method but's not work too....
i no know what's the wrong ???
Please help me .......
Sorry for bad language
Click to expand...
Click to collapse
Hi, I also have an o2 xda ignito...Download the attached file, and extract "SSPL_Manual" onto your phone and run it, the screen will go blank...now just flash with hard spl olinex 1.93 unsigned by running "DiamonCustomRUU" and then flash the rom of your choice.

Yessss it's working now
Yes it's work . Thanks for all supporting.............

Upgrading O2 XDA Ignito

Hi every one
I would like to thank every one in this forum for all the great help & support.
I have learned a lot from here on how to tweak my 1st windows mobile
My HTC is O2-UK branded :
XDA Ignito
DIAM300 64M
SPL-2.07.0000
ROM version: 2.10.206.1 WWE
ROM date: 24/06/2009
Radio: 1.13.25.24
Protocol version: 52.62.25.34H_1.13.25.24
Using O2 official ROM upgrade
[Xda Ignit2_UK_2.10.206.1_Radio_Signed_Diamond_52.62.25.34_1.13.25.24_Ship.exe]
What I want to do is just put a clean ROM (may be HTC original) without all the additional software that comes with the branded ROM
The reason for this is my windows folder is filled with unnecessary stuff that I can’t delete (like opera9 & some ringtones) which is taking some precious space (file properties show it's ROM files).
My question is:
1- Which HardSPL should I use?
I’ve read this great tutorial & I’ve gathered that I need Unsigned-Hard-SPL-Diamond-OliNex & this (correct me if I am wrong)
Thanks to cozzykim for his MiniTUT but does it matter if I have SPL 2.07 & install an older version (like Unsigned-Hard-SPL-Diamond-OliNex 1.40 or 1.93) or should I wait for an upload of SPL 2.07 ??
2- Does it matter if the SPL I install is signed or not when it comes to installing cooked ROMs in this forum vs official HTC ROMs ?
3- If I want to revert back to the stock ROM for warranty reasons, can I still do that? & how ? (revert back to same SPL & ROM) ?
I've got the extracted files from the official rom which include [01_SPL.nb] which is SPL-2.07.0000, (if anyone is interested I can upload it).
So can I reinstall this in future? or just run the full official ROM.exe installer to put everything back as it was (including original SPL)?
Before any one starts flaming about searching before opening a new thread, I did search (spent two weeks reading through different posts) & I did not find any mention (or upload) of Hard SPL 2.07 (only found 1.93).
I found previous threads with similar questions not answered so thought may be it's better to open a new thread than digging & bringing up a one year old thread.
Pardon me for my noobish questions but this is my 1st flash & I am sure it will be easier afterwards but I hope answering these questions will make it easier for noobs like me & to those with XDA ignito.
Any help is appreciated & if any moderator thinks this is a repeat post & should be closed then feel free to do so.

I have O2 Ignito and this is what I did:
1. Hard SPL - I'm using OliNex 1.40
2. Reset to bootloader to check Hard SPL .
3. Copy GSM rom to Internal Storage ( file name DIAMIMG.nbh )
4. Flash Rom ( put reset button - keep holding volume down button and back button - then release reset button ).
5. Wait until it's finish then reset.
6. Done
My fone doesn't have warranty so I don't care to roll-back to stock rom . I can't help you but I think someone can.
Good Luck !

thangkls said:
I have O2 Ignito and this is what I did:
1. Hard SPL - I'm using OliNex 1.40
2. Reset to bootloader to check Hard SPL .
3. Copy GSM rom to Internal Storage ( file name DIAMIMG.nbh )
4. Flash Rom ( put reset button - keep holding volume down button and back button - then release reset button ).
5. Wait until it's finish then reset.
6. Done
My fone doesn't have warranty so I don't care to roll-back to stock rom . I can't help you but I think someone can.
Good Luck !
Click to expand...
Click to collapse
Many thanks for the reply
One question though, does it matter if you have a newer SPL than 1.40?
I mean did you have the same SPL (1.40) before installing OliNex 1.40 or it doesn't really matter what version is in your phone?
(mine is 2.07 & I am not sure if it's ok to install an older version like 1.40 or 1.93)
Thanks

Ok I've done it
Same steps as thangkls
1. Hard SPL - used OliNex 1.40 [Unsigned-Hard-SPL-Diamond-OliNex].
2. Reset to bootloader to check Hard SPL .
3. Flashed with A.Z.T.O.R. Re-Evolution
& I must say, it looks great so far (especially the landscape feature).
I'll worry about the warranty later (though I think restoring a newer SPL 2.07 should work the same way, as explained here)
Thanks again for the help
Now am off to test all those ROMs .... wohoooooooo

Look at my signature:

Look at my signature
Actually this was the 2nd ROM on my list to test.
I liked A.Z.T.O.R. Re-Evolution but had to abandon due to a keyboard bug.
Gen.Y D2 R5.3 looks great with 15MB more storage space & same memory use.
No bugs so far.

Spl-2.07.0000
gsm 44
where can i get SPL-2.07.0000
previously i hav phone wid this specs
XDA Ignito
DIAM300 64M
SPL-2.07.0000
ROM version: 2.10.206.1 WWE
ROM date: 24/06/2009
Radio: 1.13.25.24
Protocol version: 52.62.25.34H_1.13.25.24
then i updated spl with hspl olinex
nd my spl changed
now i want to revert back to spl 2.07.0000
but how
i have gone back to spl 1.93 but not beyond that

ok i did it i got the spl 2.07.0000 back

dimanod stuck on boot ( please help ! )

i used hard spl 1.4 olinex and sucessfully
then i upgraded radio to 1.00.25.05
and then in installed wmpoweruser new 6.5.3 rom
but after flashing phone stucked on touch diamond screen and nothing happens.whats the probelm ? please help me.is for one my freinds and i promised a good rom to him and now its broken.

Use mtty procedure from this post: http://forum.xda-developers.com/showthread.php?t=540290
Or more simple write a original htc rom.

lordsinasina said:
i used hard spl 1.4 olinex and sucessfully
then i upgraded radio to 1.00.25.05
and then in installed wmpoweruser new 6.5.3 rom
but after flashing phone stucked on touch diamond screen and nothing happens.whats the probelm ? please help me.is for one my freinds and i promised a good rom to him and now its broken.
Click to expand...
Click to collapse
hard reset the device once and boot again.... post back if its stuck... will see what we can do..

[Q] Big Problem :(

I try to change my rom and everything was super till the procedure reach 15 % and stop and there were sighn that lost conecton to the PPC and my PPC die Would somebody help me ?? I love this PPC and if there is a way to bring it to life i will be very greatfull

...
youv bricked it dude, however its fixable.. you need to download your original rom (stock rom) and flash it to the device.
good luck hunting for you rom,you will probably find it on the xda artemis wiki so id start there if i was you..
when you have your original rom working on your device, download uspl 1.11.cmon..
(click in my sig to download, i have put a user guide inside.. however.. when it tells you to soft-reset, DONT..)
Uspl will basicly take the restrictions off your device so you can put any custom rom for the artemis on it.. (only the original rom will fix your problem though)
Rn
Artemis Original Roms Link

My computer can't establish conection with the PPC.There is no sighn of life even when put the usb in PPC.Should I keep trying diferent roms to find the right one ??

...
hello again..
when you turn your device on, what are the red numbers shown on your device startup/bootloader?
dont keep trying roms coz only the original will work.. anyway..
you should be able to see.. eg, my artemis info..
IPL: 3.04.0001
SPL: 1.11.cmon
GSM/RADIO: 02.94.90
OS: 3.15.0.0
just post your info (up) thats all ill need and ill send you the link to download your original rom..
(in some cases the rom is not for download, but fingers crossed eh..)
Rn

...
SPL: *.**.**** = you need original rom..
SPL: 1.11.cmon = any rom will flash, original rom not needed..
SPL: 1.11.0000 = some roms will flash, depending on size.. (original rom may be needed)
*dont worry bout pc not connecting for now
(there are other ways