Related
I updated my rom from the original spanish version to a Artemis_Touch_3.01
After some use, the device is blocked.
It starts the HArd reset, after "Format messages" It starts HTC white screen
IPL 3.13.0001
SPL 3.13.0000
and nothing more
.
It also works ROM update mode (Three colors screen) but when I execute the Rom update frommy pc, it reaches 2/3% and gives different Errors depending the ROM,
"Ivalid Vender ID [294] when I use the ROM HTC_P3300_SPA_3.13.412.1_4.1.13.44_02.94.90_Ship_R
ERROR [270]: Update Error -The Image File is corrupted - When I use Black & Blue 4.3 or Artemis_Touch_3.01
I need help!!!
brick?
hello,
First you must open the bootloader menu,
hold voice dial button and press soft reset.
If this not working hold voice dial and on/off button and softreset.
You must connect first your htc with your pc and the start the bootloader.
When you are in the bootloader menu, you can upload an orginal fabricrom to your htc.
Search xda-developer for the fabric rom.
And then you can change your rom for something else but don't forget the uspl.
When you want to change image you must install the uspl first otherwise everthing will blocked
the problem you have is that you have to run the uspl first before you can flash another firmware. If you run the uspl you will see that the spl loader of your device is version 1.11.000 and than you can flash an other rom of your choice
greetzz Patrick
uspl does not work. this is the point you can not get it.
have a problem but I cannot find anything useful for my case, maybe you can help me?
pvdhelm said:
the problem you have is that you have to run the uspl first before you can flash another firmware. If you run the uspl you will see that the spl loader of your device is version 1.11.000 and than you can flash an other rom of your choice
greetzz Patrick
Click to expand...
Click to collapse
Hi Patrick,
I have a dutch rom on my htc P3300
IPL: 1.12.0001
SPL: 1.12.0000
GSM: 02.67.90
os: 1.12.0.0
my HTC remains stuck on the startup screen (logo HTC) and will not get any further.
Connection with active synch is not possible, ans holding the buttons reset-voice rec-on/off buttons don't react. WM cannot be started in that way.
is it possible to find a boot program which allows me to start up WM again like a regular PC? something like a emergency startup disk? I have a 2GB micro SD card. After reading and trying so many things, I lost the way in this site and was hoping maybe you can send me some useful links that can solve my problem? I would appriciate the effort.I don't know if it's allowed to send my personal emailadress? If it is allowed please let me know. Maybe we can exchange directly some info, otherwise I don't have a problem mailing this site.
(I hope I can find this thread again after closing?)
Kind regards , Eli
my artemis is also in the same state
Hi All,
Please help me with problem which I am facing with my HTC P3300
When i switch it on..Its stuck in the state where it shows
IPL 3.07.0001
SPL 1.11.0000
GSM 03.08.90
OS 3.4.0.0
What I tried.
1. I tried USPL , its not loading as device is not getting detected in my laptop.
2. Volume Down+Reset is not working
Please help me with this
I really need some help!
I was following the the post The DEFINITIVE MTTY Thread!! REVISED 02-11-09 and I made a mistake as follows;
blanktruth said:
Ok, first of all I did not think that it was this dangerous to use MTTY!.
I followed everything and came to these lines
---------------------
Cmd>task 8
Cmd>
---------------------
But after Cmd>task 8 my device restarted immediately before the second line Cmd> appears and I panicked and disconnected my device and pushed the wrong buttons while "Touch Diamond" logo was on the screen.
Now, nothing happens. I can not start from the beginning because I can not start the bootloader by pushing Vol Down and the small red reset button...
Is there anything else left for me to try? Or should I throw my HTC to garbage?
Click to expand...
Click to collapse
Now, I do not know how, but I brought my HTC to bootloader mode and now I can see it via MTTY. But I mistakenly formatted the Internal Storage while I was trying to bring my HTC to bootloader.
Is there any way to upload the DIAMIMG.nbh file to Internal Storage? Or should I follow a different way to save my HTC Diamond?
i have the same probnlem!! with my diam300
my bootloader show not Diam300 64m but only 64M on the first position in 3color mode... plz help
Connect the Diamond and run the customruu.exe from your desktop, this should work.
how to connect if i used mtty... its clear everything what i have on device storage and in bootloader canot start stock or developed rom...
if i want start hard spl its say invalid model it....
blanktruth said:
I really need some help!
I was following the the post The DEFINITIVE MTTY Thread!! REVISED 02-11-09 and I made a mistake as follows;
Now, I do not know how, but I brought my HTC to bootloader mode and now I can see it via MTTY. But I mistakenly formatted the Internal Storage while I was trying to bring my HTC to bootloader.
Is there any way to upload the DIAMIMG.nbh file to Internal Storage? Or should I follow a different way to save my HTC Diamond?
Click to expand...
Click to collapse
The only thing to do now is to flash back a stock ROM or use a custom ROM with the RUU.
Solved!...
Dom1n8tr1x said:
First of, your device is supposed to soft-reset after the "task 8" command and you should have been holding down the "Volume Down" and "Back Buttons" to begin flashing your new ROM. The whole idea of using MTTY is to format your Main Storage and flash a new ROM. Therefor you should have loaded the ROM that you wanted to flash onto your Internal Storage.
Click to expand...
Click to collapse
Thank you for your reply.
Actually I had uploaded the ROM to my internal storage, but during trying to bring my phone to bootloader mode, I formatted the internal storage...
Anyway, what I did now is, first I opened the USB Connection feature from ActiveSync, and then used CustomRUU.exe to Flash the ROM...
Everything is solved now...
Thank you very much all...
ilijan said:
how to connect if i used mtty... its clear everything what i have on device storage and in bootloader canot start stock or developed rom...
if i want start hard spl its say invalid model it....[/QUOT
bootloader is all you need to revive the phone
connect it to usb in bootloader mode and just install an oficial diamond rom from an windows xp pc.
it's easy
Click to expand...
Click to collapse
plz write here step by step guide how you solved
How it was solved...
ilijan said:
plz write here step by step guide how you solved
Click to expand...
Click to collapse
Actually the most crucial part was to bringing phone to boot loader mode. And I think I managed that by pushing the Volume Down and Back (the arrow pointing left) buttons immediately after restarting my phone. And I had to do this after taking out the battery and putting it back after 5 sec.
When I pushed these buttons at the start up the phone tried to install the ROM from my internal storage, but as I explained I had deleted it by mistake. Therefore it could not find the ROM. I disconnected my phone from my PC and the screen started to say something like Retrying USB connection or waiting for USB connection, something like that.
I restarted my PC in Digitally Signed feature disabled by pressing F8 during start-up. Reconnected my phone to PC (the screen of the phone was still blinking as waiting or retrying usb connection). And voila the phone screen changed to boot loader mode...
The rest was easy. I opened the USB connection feature from ActiveSync and used CustomRUU.exe with a ROM to flash my phone...
That is all...
1. plug phone in to computer in bootloader
2. run customruu or stock from rom update on computer
3. wait for rom to flash to device
4.???
5.profit
but my booloader dont show model ID: DIAM300 64M what i had befor
and show me only: 64M
and any flash error with invalid model id, i canot flash, rom, stock rom, or hardspl...
understand me.. im not totaly noob... i used mtty X times... but now have this probles
can somebody help me?
my diamond dont have model id...
before i had in bootloader mode DIAM300 64M model id, but now i havent got... its show only 64M,
every rom flash stopped at 1% cose model id error,
every hard spl falsh finished 100% but after flash when device restart write model id error...
i cant do anithing... can somebody help me?
For everyone facing problems after flashing his/her device, take a look at the link in my sig.
There you can find a guide to restore your diamond.
you dont understand me..
i canto flash any rom any hard spl becous my diamond dont have device ID...
in bootloader dont show DIAM300 64M but only 64M
after all flash say error mobile ID...
i try mtty, hard reseted, soft... and nothing
after start its show me only first stock screan, the red text on the right bottom sight dont start: 1.17.25.14
2.100000
geny d2x
its maybe wrong but i forgot what waz here...
how can change device model ID? form 64M back to my stock DIAM300 64M?
Try another version of Hard-SPL, some people report that 1.40 not fully works.
I suggest you try 1.94 Olinex.
my diamond is death... if somebody know how can heal it... plz write me...
my device ID is missing... so i cant flash any rom, any hard spl, any radio...
try this? http://forum.xda-developers.com/showthread.php?t=409425&highlight=invalid+model+id
im not sure but i dont think one can brick his/her phone after hard spl, thats the reason of hard spl in the first place that u dont brick it. boot loader is always present
Guide
if you are using Windows XP try the following steps:
Connect your device to your PC
In Active Sync > connection settings > check Allow USB connections (which you have un-checked while doing MTTY)
Find a ROM with CustomRUU.exe / diamond wrapper
Now enter into bootloader mode(forget about the device ID)
Go to customRUU.exe and run it
Follow the ROM installation steps
This will help you installing your new ROM.
I had a similar problem and i resolved it by follwoing the above steps.
Guide
if you are using Windows XP try the following steps:
Connect your device to your PCIn Active Sync > connection settings > check
Allow USB connections (which you have un-checked while doing MTTY)
Find a ROM with CustomRUU.exe / diamond wrapper
Now enter into bootloader mode(forget about the device ID)
Go to customRUU.exe and run it
Follow the ROM installation steps
This will help you installing your new ROM.
I had a similar problem and i resolved it by follwoing the above steps.
My artemis is in the white screen.after use the Artemis_USPL (in ROMUpdateUtility level).
please help me fast.please.
...
sounds like it went wrong.lol
you probably bricked device..
take sd card out, if device goes to bootloader - red,blue,green..
there is a chance to bring it back to life.
to do this you need the official rom that was on the phone, so first things first, download that!
secondly, download ''uspl cmon'' this will let you flash more roms to your device, - with old uspl it sometimes stops at 3% because of size.. but with cmon, it doesnt!
so flash with official rom, uspl cmon, then flash a new 6.1 or 6.5 rom!
good luck..
if you need more help, message me..
...
...try this beforeyou panic..
try uspl again, once dos screen has finished, (penguin) soft reset and update uspl. device should restart and spl should be
1.11.0000 - uspl
1.11.cmon - uspl cmon!
help please,
need the original t-mobile Mda Compact Rom!!!
can`t flash other roms.
when i want to flash it shows me the error 300
i just need the original rom.
i can`t do nothing with my device!
please help me
raving_nanza said:
sounds like it went wrong.lol
you probably bricked device..
take sd card out, if device goes to bootloader - red,blue,green..
there is a chance to bring it back to life.
to do this you need the official rom that was on the phone, so first things first, download that!
secondly, download ''uspl cmon'' this will let you flash more roms to your device, - with old uspl it sometimes stops at 3% because of size.. but with cmon, it doesnt!
so flash with official rom, uspl cmon, then flash a new 6.1 or 6.5 rom!
good luck..
if you need more help, message me..
Click to expand...
Click to collapse
hi my friend .
im tryed but cant do it. when i run start_uspl it go to boot loader and occur error 260 and ... !
what is the problem ?
what i can do ?
please help me !
thank's a lot .
error 260 Here after I get to bootloader
No any one ? !
help me please !
...
error 260 is the connection to activesync dude..
you just gotta keep trying..
(remember do not soft reset)
Take SD card out and try again.
...
solved??..
raving_nanza said:
solved??..
Click to expand...
Click to collapse
no !
after start and finish artemis-uspl my artemis stay in white screen & the ROMUpdateUtility failed ! (error 260 !)
my pc windows is 7 !
excuse me for bad english write ! bacause my language is other !
tnx
...
wait for artemis to get active sync connection before continuing with the RUU..
(make sure to take memory card out)
raving_nanza said:
wait for artemis to get active sync connection before continuing with the RUU..
(make sure to take memory card out)
Click to expand...
Click to collapse
im sure my artemis connected to WMDC in win 7 !
and the SD Card is out !
after start artemis-uspl and finish my artemis(p-3350) stay in white screen ! and when the ROMUpdateUtility started(auto) in verifying information level occur 260 error !
...
after the white screen device restarts, thats when you click through the RUU
...
(let active sync gain connection before clicking through RUU)
raving_nanza said:
(let active sync gain connection before clicking through RUU)
Click to expand...
Click to collapse
in start_uspl.exe in 70% level my artemis stand in white screen & ..... 100% !
im sure when my artemis in white screen its conncted to pc !
can i run ROMUpdateUtility after white screen in bootloader or when the window are booted ? ( Manual)
Hello! I've got a big problem with my htc p 3300. It Doesn't start. What can I do? please help me
ovidiumihai said:
Hello! I've got a big problem with my htc p 3300. It Doesn't start. What can I do? please help me
Click to expand...
Click to collapse
download your original rom
what are the red numbers and letters when the device starts up?
so let me get this straight
I hard reset my default ROM
I install
- Cert_SPCS
- EnableRapi
activesync ON
start uspl (Dos)
wait for it
(Penguin)
Creating Preloader 1:1 Mapping
WHITE SCREEN & no active sync connection
How long do I wait here, before I am able to do anything? I can safely reboot however ^_^ and it goes back to WM5, like nothing happened
my device is an old Dopod P800W, never flashed before and running old ROM from 2006
Worked a treat, saved my bacon.
Many thanks
Hi ,
I was flashing my jasjam using sspl-herm and a 6.1 rom ,
While upgrading the progress bar reached the end but it stayed saying upgrade in progress , it took too longer than normal and i knew it wouldnt continue so i soft resetted the phone ,
now it's stuck in the splash screen before even the windows loading.
Plz plz plz help....
try doing a hard reset not just a soft reset that might help
medo_punsher said:
Hi ,
I was flashing my jasjam using sspl-herm and a 6.1 rom ,
While upgrading the progress bar reached the end but it stayed saying upgrade in progress , it took too longer than normal and i knew it wouldnt continue so i soft resetted the phone ,
now it's stuck in the splash screen before even the windows loading.
Plz plz plz help....
Click to expand...
Click to collapse
if u have loaded hardspl then hold power button + OK button on sides of phone and then stick stylus into reset button an dthis should get u 2 red, green, white, blue colour screen and then plug usb in and re-flash
get hermes in bootloader mode, connect USB cable and flash with this http://www.4shared.com/file/61372397/e2bf76c0/official_ATT_WM6_striped.html
Hey ,
Thnx guys 4 help
1st I tried hard resetting and it didnt work
2nd I DONT have hard spl
3rd I get into bootloader , i plug the usb cable but i cant flash , the ruuwrapper program says error during upgrade , i think it cant access the phone first coz the mobile device icon in my computer is emtpy , second activesync says not connected(although it tries to) and device manager reads an " htc usb sync " drive but no letter or something
Still no luck , any help ??
Activesync doesn't need to be runing.
download mtty and do like he said here "http://wiki.xda-developers.com/index.php?pagename=Instructions for those stuck on Boot Screen" (copy all text between " " and paste to your browser).
After "set 14" give "task 8"
Try flashing from SD card, first the HardSpl ant then the Original Stripped ROM.
@TheMim : tried but didnt work
@eryunt : how ?? i have a custom rom with the name HERMIMG.nbh on my sd card but it doesnt upgrade it says loading for a few seconds then some red numbers and letters appear at the top of the screen then it goes into the bootloader and doesnt upgrade
NOTE THAT : i dont have hard spl (no supercid)
Thnx again , plz help
Try downloading HARDSpl7 from here:
http://forum.xda-developers.com/attachment.php?attachmentid=35136&d=1173326890
Unzip it and rename the file "RUU_signed.nbh" in "HERMIMG.nbh"; put it on SD and so you will flash the HARDSpl.
Then, make the same thing with the file "RUU_signed.nbh" extracted from an original shipped ROM.
Hope it fixes your Tytn
Many thanks for your help , i will try that tomorrow but one final question ,
How can i access my sd card with no phone ?? do i need an external sd-to-usb device or something like that ??
medo_punsher said:
How can i access my sd card with no phone ?? do i need an external sd-to-usb device or something like that ??
Click to expand...
Click to collapse
Yes, you need an SD-Reader for your PC
Okay , now i have a cooked rom on my sd card (fat32 formatted) named HERMIMG.nbh when i get into bootloader it says loading for a few second then a red number "00068002" appears at the top of the screen and it continues to the tri-colour bootloader
any help ??
Have You already installed HARDSpl correctly via SD-card?
No , i didnt but will it work or i will get the same red number ??
PS : my bootloader version is 1.04 so i guess i dont need hard spl as this one can flash any rom , right ??
medo_punsher said:
No , i didnt but will it work or i will get the same red number ??
PS : my bootloader version is 1.04 so i guess i dont need hard spl as this one can flash any rom , right ??
Click to expand...
Click to collapse
Try downloading HARDSpl7 from here:
http://forum.xda-developers.com/attachment.php?attachmentid=35136&d=1173326890
Unzip it and rename the file "RUU_signed.nbh" in "HERMIMG.nbh"; put it on SD and so you will flash the HARDSpl.
Then, make the same thing with the file "RUU_signed.nbh" extracted from an original shipped ROM.
JUST FOLLOW ALL THE STEPS ABOVE
No no no no..... HSPL cant be upgraded now via SD card cause th SSPL was unsuccesfull!!!!!.....
Get a XP PC... your batt must be 50% charged or more "better", a working USB cable
NO SD CARD inserted... your XP pc must have NET frameworks 3.5
put your device in bootloader mode.... and upgrade any stock rom to rewrite a valid SPL cause your is corrupted now
then when you get a stock rom working via SSPL you will be able to redo the steps to flash HSPL V7
When turned on it shows a HTC screen with :
IPL 1.12.0001
SPL 1.12.0000
GSM 02.67.90
OS 1.12.0.0
I can get into bootloader mode but doesn´t know what to do then. Tried a hard reset but ends up with the same start-up screen.
I downloaded mtty because I saw in another post I might need that. Think I also need a Danish Rom, but have no idea how to get one.
Hope someone can help me?
...
if you gona use mtty.. (might not be needed in your case)
when it opens TYPE (no copy and paste, it wont work)
Cmd>password BsaD5SeoA
Cmd>ruurun 0
Cmd>ResetDevice
anyway..
you cant go no further than the start-up screne because I GUESS you tried flashing with no USPL..
click 1.11.cmon in my signature to download..
uspl 1.11.cmon will basicly take the security off the device so an unofficial/cooked rom can be flashed no matter what the rom size is.. instructions inside uspl1.11.cmon folder..
youl need your original rom though which can be found here
so.. to do list:
*find original rom - i think its the English or French rom..
*flash original rom - run ruu or use mtty
*do uspl 1.11.cmon - DONT SOFTRESET when instructions tells you to!
*flash new unofficial/cooked rom
DONE
any questions or if you get stuck, just private message me and ill help the best i can..
Rn
Thanks. I´ll try it out this weekend.