my tp2 touch screen is not responding suddenly!!! the problem started only after i answered some call through the screen slider, however, the touch screen is not responding to my fingers ever since !!!!
now i'm operating the phone only through the buttons !! but as if it is not touch screen!!
anyone have a clue about what the problem can be?? please help me. my device runs wm 6.5 and this is the first time to have this problem, i did soft reset many times but no imrovment!!
I had SOD this early morning and it was my first, do you guys think there is a relation between these events???
I have the same problem.
Just happened this morning.
I was able to use my mobiler to access the screen.
Tried several hard resets. No luck.
Tried re-installing energy Rom (4.1)
Then tried the new Energy Rom (4.11) still no luck.
But then I got the big idea to go back to the stock ROM. Now I cannot use the on screen prompts to access "my mobiler"
Anybody have any suggestions or is it back to AT&T for a new phone?
so whe you back to the stock rom, did u get ur screen working again??
No. no workey
Now that stock rom is on. I keep going back to the "Sim Card Changed" screen. I can not tap "cancel" or "Next". I can use the hard buttons so I am able to get to the phone and then use keyboard to dial.
Still no touch screen. And no work around with keyboard to get to screen. need a "Tab" button. then might be okay.
this sucks.
Just a quick bump before I go to AT&t in the morning.
Try running task 29 and then flash back to a stock.
And have you tried taking your sim card out of you're phone? Maybe that will avoid the message.
i'm buying a black berry
Does your screen look as if an oily residue is under the touch screen part?
My screen stopped responding a few weeks after the appearance of the 'oil' and Vodafone swapped it with no problems. It seems like a fairly common problem
yes, I've got that oily spot and somehow i managed to relief the problem only for minutes when i raised the digitizer carefuly which got me the screen working for few minutes untill it went unresponsive again after while. I'm looking forward to do alcohol swab to this oily spot and will see weather this will solve the problem..
Related
I have a Siemens SX66 which has worked great since I got it when it came out. Recently I cracked the screen so I replaced it with a new lcd including touch screen. The screen is a geniune HTC Sony screen. After putting it together again the software was reset. It asks to touch the screen to begin. Then, it goes straight to "align screen" and asks to tap the target at each location as it moves around to align the screen.
It seems to be stuck there because I have had it cycle through the same spots (original and 4 corner spots) over and over at least 20 times without going to the today screen yet.
I tried reflashing the software and after a successful flash it still does the same thing.
Can someone tell me what to do to make this thing work again?
Same thing here :0
Did you two guys solve your problems?
I have the same problem, I am still trying to fix it. I suspect from the backup battery, since before I hard reset my SX66 all programs lost their configuration when I turn off and on again my SX66, and when I tried to realign the screen the align cycle repeated forever. Then I tried hard resetting, reflashing to various OS's and I can not pass the initial calibration screen.
Please keep me posted if someone have found the way to solve it.
Thanks !
ok so i searched on the sites for a fading to a white screen problem but it looks like its related to the dpad... my phone was really low on battery last night it kept beeping continuously... so by the time i got to plug it in the screen started to fade to white... now the screen has vslight vertical lines and every time i shut off the phone with the power button and turn it on it comes normal but as soon as u touch the screen it fades to white!!! was this caused by the low battery. i fully charged it but still have the same prob. i tried clearing my storage and that didn't help..what do i do?
white screen
you will need to replace the board for the dpad.
ok thanks. is this the same issue that others are having as well? the wierd thing is half the time it works the other half it doesnt...
I had a similar problem. I had pressed the power button to check the time and screen was white! SR rebooted and after the first splash screen the screen faded to white. I finally founded a product called Pocket Controller http://www.soti.net/ (trial ver works fine) that allowed me to see my phone on my computer. I was then able to backup my data to the storage card. I reflashed the phone and it’s worked fine afterwards.
yeah man thats what happened to me exactly... im reflashing the official wm6 rom now... ill post what happens... thanks
Silverexp said:
I had a similar problem. I had pressed the power button to check the time and screen was white! SR rebooted and after the first splash screen the screen faded to white. I finally founded a product called Pocket Controller http://www.soti.net/ (trial ver works fine) that allowed me to see my phone on my computer. I was then able to backup my data to the storage card. I reflashed the phone and it’s worked fine afterwards.
Click to expand...
Click to collapse
damn it didnt work with me my screen still goes in and out when it chooses to. and it is my dpad b/c it stops working when the screen is gonna go..
Hi,
Try tightening the screw behind the red hang up button on the dpad. There is a component behind there which causes this problem. If tightening doesn't work try loosening. It's all to do with the pressure on the chip. Very odd problem.
Also try squeezing the bottom right hand corner of the phone and SR.
Bonkers solution for a bonkers problem but it certainly fixed one of mine.
Good luck!
yes, the screw tightening/unloosing thing works for me. same thing happened when i dropped my unit. i even completely dismantled it (managed to fix the microsd card spring). something loose with the connections.
niec guys thanks... i will try the tightening and loosening the screw... i tried holding down the bottom right and SR didn't work but thanks anway... i guess i have to buy a screw driver to open this thing up... god i remember when i had to take apart my mpx 220 im getting flashbacks!!!
Had exactly the same problem but mine was due to an phone shop employee dropping it. It would do exactly the same as yours. Sometimes it would work fine and once when I reflashed it the problem went away for a few days but if came back.
I used to control it using Soti pocket controller but them migrated to Net Support as that allowed me to control over wifi. In the end had to get it replaced.
i have been using the p3300 for a month now an it was working fine but all of a sudden i couldn't use my stylus. i tried the screen allignment but the screen didnt respond so i restarted the device. this also didnt work. i also tried a soft reset. no results so i did a hard reset now i am stuck at the screen where it says " Tap to start your device "
Plz Help....
Hi
It sounds then like the touch function of the screen has stopped working.
If you have only had it a month depending on where you got it you may be able to return it.
Sorry about this
Cheers Dave
maybe
seems like that to me too
still i hope i wont need to
anyway thanks
no problem
Anytime
If you have not yet returned it, try taking the screen protector off if you have one on.
My screen stopped responding to touch a while back. When I took the protector off all was fine.
could be it
may be but i am not sure about it i will try it nonetheless
Thanks
screen needs rest ??
nope no use the screens gone crazy i guess
it recognises a few strokes when left for a few hours the goes dead again
maybe it need some rest
On the screen, round the edges make sure there’s no gunk under the gap between the case and screen. You will be surprised what can get under there. Flat Plastic tooth picks are good for clearing it
i am nooob
cant try it
dont really know how to remove the screen guard
cant find the seam
Hi
You might not be a Noob. You can only remove a Screen Guard/Protector if you have actually put one one.
Also i still dont think there is much you can do.
If it does work after a while it is possible that the screen calibration has gone haywire If you get chance to use it try doing that it may help
Cheers Dave
mine to same problem please help
Hi all, I got my touch pro 2 through Orange a while back and I have this frustration which is really ticking me off. The touch screen stopped working!
It looked like it had a fine film of transparent oil which surrounded a fine grid pattern which you could see if you held your phone against the light at an obscure angle. Nothing is more infuriating than trying to back up your phone, or import emails onto the computer before sending it away for repair, to find that the back up software that comes recommended can't be installed because... wait... you guessed it.... you need the soddin touch screen to install the bloody thing.
My question to you guys is this, has anyone found a way to use the keyboard as an alternative to 'ok', 'cancel', 'install' and other important functions?
It has already been away for repair becuase of this 'recognised' issue, and now it's gone again. I'm getting fed up with HTC stuff going faulty on me, and i've had a lot of their products, however nice the phone is.
Thanks in advance for any and all assistance...
insomnai
I hope someone might actually help me out with this. I used my phone perfectly good yesterday, tonight, i put it on standby, and go to bed. Woke up in the morning, i grab my phone, turn it on from standby mode, everything's fine, but digitizer is not answering to my touch. Soft-reset, and try to put pin, but all i get is pressing 1 / 4 / 7 no matter which part of the screen i actually touch. I haven't been flashing it for months, and i had the latest simplicity rom when this happened. Thought it was an alignment problem, so i navigated with keyboard till the align screen, and tried to align. It went in loop, as soon as i pressed the last align point, it went back to the first point, without letting me exit. Tried to re-flash with a stock rom, same problem. Tried to re-flash with an energy rom, same problem. Anyone got any ideas of what the hell happened?
May be some condensation/moisture in between the outside screen and the touch screen. This happens to me all the time when its in my pocket and its hot out. Try using your finger nail, or something, to go around the edges of the screens plastic. It will let moisture escape.
Good luck.