please help as diamond is not responding(after installing spl)
--------------------------------------------------------------------------------
i installed some diamond spl on diamond although it completed 100 percent and turned off, and model id error flashed on screen, now it is not responding (not turning on) is there any solution to install any spl either stock or hard any so the device can turn on , plz help........any way to spl at this stage?
Related
can anyone help me? Im new with PDA. What happen was i tried to upgrade my PDA, and i manage to install the satin black. after trying another os my pda doesn't want to reboot when the installation was succesful. tried hard reboot and it goes to the red green yellow and white screen. now everytime i get the spl 1.40 to install it works till 100% but after that it won't reboot. what can i do? thx. please help
you should hard spl your x01ht first before upgrading your pda.
did you do hard spl first?
what is your radio rom, SPL??
Hello Experts..
HELP ME PLZ
i have
I-Mate JASJAM HERM100
IPL-1.00
SPL-1.04
i was flaishing (installing) the rom from my laptop to the i-mate
it starts ok,
then when it reached 6%, connection error happened
then followed the steps, (to remove the battery, and turn on the device again)
but it didn't repair it
now when i turn on my device, it starts in the bootloader screen (the red/green/blue lines)
and in the red line is written
HERM100
IPL-1.00
HERM100
SPL-1.04
and i can't connect it to my computer to install or flash a new rom...
I tried to flash the rom from the SD Card, after it finnished , (updated successfully) or something like that, i restarted the device , it returns into the bootloader screen
what can i do, and which programs or roms shall i use...
thanx a lot for the one who can help me....
Don't panic check this link and read carefully through it.. http://wiki.xda-developers.com/index.php?pagename=Hermes_SDCardFlashing and try this link as well http://forum.xda-developers.com/showthread.php?t=296722 i wish u good luck.. and don't forget before before starting to flash to pass by this link too http://forum.xda-developers.com/showthread.php?t=295751
What ROM were you flashing? Do you have HardSPL installed? Have you read wiki on how to flash ROM?
HERM100
IPL-1.00
HERM100
SPL-1.04
It seems you forgot to hardspl the phone before you flash it....
Hello, I was re-flashing my SPV M3100 (with hardspl v7 oplio 2.10) from Schaps WM6Pro_Hermes 4.30 WWE Full Rom to the 20070311 Hermes WM6 LVSW rom, at about 22% of rom being updated, the USB cable was accidently unplugged from my device
I plug it back up and try to restart the process but it gives me a "ERROR [260] UPDATE ERROR" message and my PDA screen stays at windows mobile and my Activesync 4.5 can't connect to my PDA
When I try Soft Reseting or Master Reset, it will try to load and I see red letters on the HTC boot
M 05
S 04 NO GSM (appears for about 8 sec.)
B 06 D 3.62
After the red words clear and it stays frozen on the windows mobile screen. Can someone please help me..
put the phone into boot loader and try flashing the rom again.
Hi Joshkoss,
I have tried many times re-flash the rom and sim unlock under bootloader, however all doesn't work at all.
IPL: 1.01, SPL: 1.09.
Could you please kindly advise?
Thanks in advance..
try the stock shipped rom from bootloader, maybe it will "see" it.
It looks like you do not have hardspl v7 installed. With hardspl your spl line should say 2.10 olipro
You need to flash the original orange rom to your spv m3100, what country you are in is important, if in the uk use the rom update from orange on there website, if any other country then use that update.
hey guys, thanks alot for your advice.
cheers..
Dear All,
Please urgent help required.
my HTC P3300 (Artemis) stuck up when i was trying to start it up. when i use to turn my cell on, i goes to the starting screen shows the following numbers and then stuck up.
IPL 3.07.0001
SPL 3.07.0000
GSM 02.69.90
OS 3.7.0.0
the screen does not move after that. i tried soft reset through the reset button but result is the same.
i also tried hard reset and when i puch the green phone button to proceed, a message come "FORMAT FAILED" and the phone stucks up.
i am quite a lot of problems since i have upgraded to WM6 from WM5 last week.
i am quite sucked with this problem. not been able to use my set since yesterday.
please also note that my HTC was not syncing with my PC since i have upgraded to WM6.
PLEASE HELP URGENTLY.
Nomi
HTC P3300
Follow this link and have a deep read
http://wiki.xda-developers.com/index.php?pagename=HTC_Artemis
I upgraded my htc-p3350 with "WM6[1].1 EN - Meschle Artemis Touch 4.02 Full with 4 sided cube.rar" completely. but did not work truly.
then upgraded again with: "HTC_P3300_WWE_3.13.405.1_4.1.13.44_02.94.90_Ship_ R.exe"
upgrade process stopped on 50% .
after that I was unable to upgrade my phone by any ROM because it shows "error 244"
How can i install any ROM on my phone. please help me on this problem.
current ipl/spl:
ipl: 3.13.0001
spl: 3.13.0000
gsm:02.94.90
os: 3.13.0.0
looks like your phone is bricked. did the connection was lost during the upgrade process?
i suggest u go look for the original rom installed on your phone
Dear mvenneker thanks for your help.
I have installed these ROMs bellow
ART_HTCWWE_11240501_026790_WWE_Ship.exe
ART_HTCWWE_depoda-artemis-original rom.exe
But all of them didn't installed completely and they progressed just up to 2%
and after that it shows "error 244" .
can you suggest any suitable ROM for my phone.