Help plz!!! Error with flashing rom !!! - 8525, TyTN, MDA Vario II, JasJam ROM Development

Hello Experts..
HELP ME PLZ
i have
I-Mate JASJAM HERM100
IPL-1.00
SPL-1.04
i was flaishing (installing) the rom from my laptop to the i-mate
it starts ok,
then when it reached 6%, connection error happened
then followed the steps, (to remove the battery, and turn on the device again)
but it didn't repair it
now when i turn on my device, it starts in the bootloader screen (the red/green/blue lines)
and in the red line is written
HERM100
IPL-1.00
HERM100
SPL-1.04
and i can't connect it to my computer to install or flash a new rom...
I tried to flash the rom from the SD Card, after it finnished , (updated successfully) or something like that, i restarted the device , it returns into the bootloader screen
what can i do, and which programs or roms shall i use...
thanx a lot for the one who can help me....

Don't panic check this link and read carefully through it.. http://wiki.xda-developers.com/index.php?pagename=Hermes_SDCardFlashing and try this link as well http://forum.xda-developers.com/showthread.php?t=296722 i wish u good luck.. and don't forget before before starting to flash to pass by this link too http://forum.xda-developers.com/showthread.php?t=295751

What ROM were you flashing? Do you have HardSPL installed? Have you read wiki on how to flash ROM?

HERM100
IPL-1.00
HERM100
SPL-1.04
It seems you forgot to hardspl the phone before you flash it....

Related

Need help ! cingular 8125 bricked :(

Hey iam new to this upgrading,CID unlocking etc.
I just bought my Cingular 8125 three weeks before.
I tried upgrading to WM 6.0 The update process completed successfully but after the reboot my mobile was back to factory default with wm 5.0.
without tring the lokiwiz to unlock, i used shelltools to flash the wm6.0.
it was successful, it asked me to do a hard reset.
Since then i am stuck up with the boot screen.
I can't get my Mobile back working.
i tried flashing with the Offical rom but of no use.
i have tried button rom, love rom. nothing works out.
without much knowledge i upgrade my spl & IPL to 3.08
now i am not able to downgrade that too.
tried flashing different roms but of no use, still it stucks up in the boot screen.
the only hope iam having is i am able to get into the boot loader.
I am not sure, where to post this thread, my appologize if i have posted in the wrong page.
below is the information i have on the screen
IPL 2.26
SPL 3.08
GSM 01.12.10
OS 1.5.4.2
Some one please help me out. i am very much worried, any help is very much appreciated.Thanks a bunch in advance !
dosai.
Have you tried flashing from the bootloader to an official rom?
thanks for reverting, i have tried that too, but of no use.
Sounds to me like you didn't run the Cert_SPCS and EnableRapi cab files before flashing with ShellTool. Being stuck at the splash screen is a dead giveaway.
I never did understand why someone would attempt to flash a ROM without doing ALL the steps. . .
i did ran Cert_SPCS and EnableRapi cab before running the shelltool. shell tool took around 10 mins to complete the update.after restart, my phone stucked up in the boot screen!. (i remember not unlocking the cid before proceeding with the shelltool) .
is there any way to get the mobile working i am too worried.
Solution
Hi, press and hold the CamShot Button and press the Power button, when you see a multi-color screen you can make a update again.
Hello all Im new here and have the same problem. I followed all the steps and followed all the instructions to fix this problem but nothing. I am stuck on the multi-color screen and i can't do nothing! HELPPPPPPPPPPPP!

help me plz i am stuck in os screen after try to update from schapes 3.3 to 4.0

hi plz every one who can help me it very urgent..
i try to upgrade my friend htc hermis but i am stuck in os menu
previusly i install scap rom 3.3
i treid to install the new version it reached 2% and the an error massege appear (connection error) then i tried to do it again but evry time i try the same maasege appear on the phone (coonection error )
it reach 0% and this message appear
i have spl 1.09
i also tried to hard spl it but still the same message ...
i treid different usb and pc but still
i download an official rom the same message
i sleep a see the same f*cking message
plz help me
IT Would help if you Gave the Error Message # for Example If your Getting Error Message 240 It's a Connection Problem.
Try Turning of your Firewall, Have the Rom you are upgrading to in your Root Directory And Always Make sure your Phone is Super CID unlocked.
Hope This Helps.....I"ve been where you were at once... IT was the My Firewall for me.
Try flashing your Operator rom using the SD card method. Or looking at the Unbrick table done by POF. It's all in the WIKI...
halder said:
hi plz every one who can help me it very urgent..
i try to upgrade my friend htc hermis but i am stuck in os menu
previusly i install scap rom 3.3
i treid to install the new version it reached 2% and the an error massege appear (connection error) then i tried to do it again but evry time i try the same maasege appear on the phone (coonection error )
it reach 0% and this message appear
i have spl 1.09
i also tried to hard spl it but still the same message ...
i treid different usb and pc but still
i download an official rom the same message
i sleep a see the same f*cking message
plz help me
Click to expand...
Click to collapse
Try booting in debug mode (hold the Side OK button + power button and reset at the same time)
once you booted into that 4 colored screen with SPL/IPL listed, flash the device with HardSPL 0.7
Link Here
Then upgrade your device again.
using HardSPL it ensures your device will not be overwritten with bad blocks and it enables unsigned rom files to be written to the phone. it's a win-win if you upgrade it.
still the same message 262 update error.
i triecthe hard spl but s6s error always appear
i can go to boot screen
plz if there solution tell me..
its not afirewall fault..
halder said:
still the same message 262 update error.
i triecthe hard spl but s6s error always appear
i can go to boot screen
plz if there solution tell me..
its not afirewall fault..
Click to expand...
Click to collapse
This 262 Error Message I got this
""ERROR [262] : UPDATE ERROR
This error occurs during the CE ROM code upgrade process.
Solution: If this happens, you can just soft-reset the device and run RUU again. The update process will then continue.
Note: At this stage, the Wince is destroyed; instead, it is in upgrade mode.""
At this Point I"m Stumpped I"m hoping one of the Big Boys Will Step in on this one and give you a better Solution....
yes it reached 2% then it stuck there i treid to reupgrade with the same rom no luck..i tried different rom also ..
do u think if i download a shiped htc rom it will work
halder said:
yes it reached 2% then it stuck there i treid to reupgrade with the same rom no luck..i tried different rom also ..
do u think if i download a shiped htc rom it will work
Click to expand...
Click to collapse
Wam7 has already given the best advice to start unbricking your phone.
1. Get the original Rom which came with your phone. It might be listed here http://wiki.xda-developers.com/index.php?pagename=Hermes_Upgrades or here http://wiki.xda-developers.com/index.php?pagename=Available Original Shipped WM6 ROM Versions. If it is not listed you'll need to search the internet and/or this forum.
2. When you have your original ROM, flash it to your phone from the SD card, not from your computer. Instructions to do this are here http://wiki.xda-developers.com/index.php?pagename=Hermes_SDCardFlashing. Remember to have a full battery charge before beginning.
Hopefully this will recover your phone. If it does, then make sure that you flash Olipro's HardSPL 2.10 (V7) to your phone http://forum.xda-developers.com/showthread.php?t=296722.
If you get stuck on how to do this correctly, there is some good advice in Mrvanx's upgrade guide http://forum.xda-developers.com/showthread.php?t=299462.
Also, in the future it can help others to help you if you give more information about your phone such as phone type, original ROM, current Rom, Radio version, SPL version etc, etc. Most people include some of this info in their signature so they don't have to keep re-typing it.
thank you very much for replaying...
i tried the sd card method and i download my exact cid rom but still it give the error 0068002 i download more than 5 original shiped rom same message
my phone is htc ...tytn ..not qtek or dopod ....
htc pure
info
r 1.18.00.10
g 32.55.7018.01h
d 3.57
m05 s04 b06
any other solution
i can go to boot menu
plz again
i tried evry possible way to flash my phone but i cannt get it done why??? EROOR 262
i download more than 10 official rom (htc) and i apply the exact sd method steps still it give me 0028002 error
my device is HTC ...BUT HTC WHAT I DONT KNOW...IT JUST HTC ONLY
SO I CANNOT CHOOS MY EXACT CID ROM
PLZ HELP ME OR I WILL THROUGH IT AWAY
plz answer me its very urgent?????
ok i dont want to open a new thread with same question.so if some one plz can help i will be graetful....
i want to knew how to fix error 262
Have you tired flashing from the bootloader?
Have you tired flashing just the rom from mitty ?
Is the phone unlocked? Have you thoroughly read the unbricking thread in the wiki?
WB
i dont know if its unlocked but i flash it with chap 3.7 a then i tried to flash it with chap 4.00 it reach 2% and stoped..ofcouse its unlocked..
it tried the mitty way but it give
level=ff instead of 0
and bad command
it tried the sd card method the error 0068002 or invalid vender id
If you get invalid vendor error doesn't that mean the phone is locked?
since no one helped me here in this thread ...i helped my self..
i found the solution...i send my ID to htc.com and they replay nicey and send me the link to my exact cid rom ..
the problem was my original rom was norway not wwe ..**** who thought that???
anyhow thank you for all who tried to help me..really i benfit from thier method for future desaster???
see u in another problem...
cuz we know nothing we just ask and ask until we find the solution ..

My SPV M3100 bricked, can anyone help me?

Hello, I was re-flashing my SPV M3100 (with hardspl v7 oplio 2.10) from Schaps WM6Pro_Hermes 4.30 WWE Full Rom to the 20070311 Hermes WM6 LVSW rom, at about 22% of rom being updated, the USB cable was accidently unplugged from my device
I plug it back up and try to restart the process but it gives me a "ERROR [260] UPDATE ERROR" message and my PDA screen stays at windows mobile and my Activesync 4.5 can't connect to my PDA
When I try Soft Reseting or Master Reset, it will try to load and I see red letters on the HTC boot
M 05
S 04 NO GSM (appears for about 8 sec.)
B 06 D 3.62
After the red words clear and it stays frozen on the windows mobile screen. Can someone please help me..
put the phone into boot loader and try flashing the rom again.
Hi Joshkoss,
I have tried many times re-flash the rom and sim unlock under bootloader, however all doesn't work at all.
IPL: 1.01, SPL: 1.09.
Could you please kindly advise?
Thanks in advance..
try the stock shipped rom from bootloader, maybe it will "see" it.
It looks like you do not have hardspl v7 installed. With hardspl your spl line should say 2.10 olipro
You need to flash the original orange rom to your spv m3100, what country you are in is important, if in the uk use the rom update from orange on there website, if any other country then use that update.
hey guys, thanks alot for your advice.
cheers..

jasjam and the file Custom_RUU.exe

hello each rom that i download and have the file Custom_RUU.exe
not working on my imate jasjam
whats happening is : the rom start the installing process and when the imate needs to load the boot loader screen (blue red green) just before the process of the rom copying should start the phone goes to sleep mode..
mainly i just want to install energy rom 3.0 on my imate ..
is that problem can be solved ?
bennylu said:
hello each rom that i download and have the file Custom_RUU.exe
not working on my imate jasjam
whats happening is : the rom start the installing process and when the imate needs to load the boot loader screen (blue red green) just before the process of the rom copying should start the phone goes to sleep mode..
mainly i just want to install energy rom 3.0 on my imate ..
is that problem can be solved ?
Click to expand...
Click to collapse
hi dude!
For first time flashing and newbie:
Please flash HardSPL and OEM Stripped AT&T first before you can flash Custom ROMs.
HardSPL link: http://forum.xda-developers.com/attachment.php?attachmentid=37669&d=1177280888
OEM Stripped AT&T: http://www.4shared.com/file/61372397/e2bf76c0/official_ATT_WM6_striped.html
Flashing method :
Withactivesync http://wiki.xda-developers.com/index.php?pagename=Hermes_UpgradeForBeginners
For How to flashing with MicroSD,http://wiki.xda-developers.com/index.php?pagename=Hermes_SDCardFlashing
And Hard reset after flashing rom
good lucky !
hi!
thanks for the fast replay
ive done exactly as you said but the problem stays ..
if i flashing roms that comes with the file RUUWrapper.exe
i have no problem
is there any convertor that can convert between those types?
Mate, use the sd card method... No problems with syncing ever again...

rom doenst want to install

Hello,
With the mtty method, i wanted to install a new rom. I did this a lot of times before so i know how to do it. I copied the rom to the memory and used mtty to instal it. But it keeps get stuck at "loading..." Because the mtty i dont have a rom to start up at the normal way.
When i am at the bios of the tel and connecting by usb to my computer, i also tried to install a rom from the computer, but there it keeps stuck at 0%. When i re-install hard SPL, that goes fine (but my tel. doenst want to boot).
Also i tried a other rom, but that doenst whant to install too.
Can someone help me?
Hi
same problem.
use olinex again.
AMIRHADI DAISY said:
Hi
same problem.
use olinex again.
Click to expand...
Click to collapse
Hello,
I installed olinex hard SPL again, but my tel doenst want to boot. It only shows the "HTC diamond" starting screen.
Fixed! I tried a other hard SPL

Categories

Resources